Conifer II Ultraflex Administrator Guide

CONIFERII ®
WIRELESS TELECOMMUNICATION TECHNOLOGY
Warning: Installation of Antenna near
power lines is dangerous!
Type certified for operation under Part 21.909.
Ultraflex® System Must Be Professionally Installed.
Ultraflex®System
Transverter
Installation & Operator Manual
Photo shows Transverter installed with 18dBi
Microceptor, Model QD-2450. Optional 18dBi
(Model 18T-2127) and 24dBi (Model 26T-
2127) available.
Page 12.

Ultraflex® Two-Way System
Packing List
(1) Response Antenna
Options
•QD-2450
•18T-2127
•26T-2127
(1) Transverter
(1) Power Supply/Inserter
(1) GPS Antenna
(2) Transverter Mounting Brackets
#726055 for inch pipe
#726044 for 1-2 inch O.D. pipe
(2) “L” Bolts #163155.2
Response Antenna Options
QD-2450
(2) #6 x 1/2” Stainless Screws
Model 26T-2127
FEED BOX
(1) Feed assembly
(1) Sub-reflector
(1) #6 x 1/2” stainless screw
(2) Stainless 1/4 x 20 hex nuts
(2) Stainless lock washers
(2) Stainless carriage bolts
REFLECTOR BOX
(2) Reflector halves
(2) Stainless U-bolts
(2) Mast clamps
(1) Mounting "L" shaped bracket
(4) Keps nuts
(4) #8-32 machine screws
(6) Stainless 1/4 x 20 hex nuts
(6) Stainless lock washers
(2) Stainless carriage bolts
(1) Stainless flat plate washer
Model 18T-2127
FEED BOX
(1) Feed assembly
(1) Sub-reflector
(1) #6 x 1/2" stainless screw
(2) Stainless 1/4 x 20 x 1" carriage bolts
(2) Stainless 1/4 x 20 Hex nuts
(2) Stainless 1/4" lock washers
REFLECTOR BOX
(1) Reflector
(1) Mast clamp
(1) Mounting "L" shaped bracket
(1) Stainless U-bolt 1/4 x 20 x 2"
(2) Stainless 1/4 x 20 Hex nuts
(2) Stainless 1/4" lock washers
(1) Stainless flat plate washer
#1
#2
#3
Page 2.
GPS Antenna
GPS Port
Antenna Port
(located on side
of transverter)
Mounting
Bracket
“L” Bolt
Figure 10
Bracket
Chan-
nels
Input/Output
-20dB Test
Figure 9
0-20 dB
Attn.
Downstream
To “Ant”
To “Set” Figure 11
Figure 8
11. Connect the downlead cable
to the input/output on the
Transverter. (See Figure
9.)
Page 11.
10. Mount the Transverter on the
mast by sliding the mounting
bracketsand “L” Bolts into the
bracket channels on the
backside of the Transverter.
(See Figure 10.)
12. Run the downlead to
the PS-0200 power supply
connector labeled “To
Ant”. (See Figure 11.)
13. Run a cable from the
PS-0200 power supply
connector labeled “To
Set” to the set-top.
(See Figure 11.)

Antenna
Output
GPS Antenna
GP-0100
Transverter
TR-2278
Response Antenna
QD-2450
Antenna Port
(located on side of transverter)
GPS
Port
Polarity
Position
INSTALLATION / ASSEMBLY
with QD-2450 Response Antenna
1. Determine the polarity of the antenna. (See Figure 1.)
NOTE: See labeling on the back of the QD-2450 antenna for horizontal
and vertical polarity positioning.
2. Connect the QD-2450 antenna output to the antenna port on the side of
the Transverter. (See Figure 1.)
3. Secure the transverter and antenna connection with a #6 stainless
screw on each side of the Transverter. (See Figure 1.)
4. Connect the GPS Antenna to the GPS port on the Transverter. (See
Figure 1.)
NOTE: Warning! GPS Port Only - +5VDC output 0 VDC input maximum.
Figure 1 #6 Stainless Screw
(One on each side)
V
E
R
HOR
Page 3.
Figure 5
Mast Clamp
U-Bolt
Figure 6
Mast Clamp
Tilt Holes
Mast Clamp 6. Attach the feed on the
front with 2 carriage
bolts. Secure on the
back with the lockwashers
and nuts. (See Figure 4.).
7. Place the 2 mast clamps on
the 2 U-bolts. (See Figure
6). Fasten the U-bolts on
the “L” bracket with the 4
lockwashers and nuts
(See Figure 5).
NOTE: By eliminating 1 mast
clamp and U-bolt, the optional
fixed tilt holes provide eleva-
tion in 100 increments. (Not
recommended under high
wind conditions.) (See Figure
6.)
Use the flat plate washer on
the adjustable tilt slot to
secure the antenna to the
required elevation. (See
Figure 7.)
Figure 7
Tilt Slot
Page 10.
8. Connect the GPS Antenna to
the GPS port on the
Transverter. (See Figure 8)
9. Connect the 26T-2127
antenna output to the
antenna port on the side of
the Transverter. (See Figure
8)

6. Mount the complete unit on a
1-2” O.D. mast or on Conifer’s
optional DS-1000 mount assembly.
(See Figure 3.)
7. Connect the downlead cable to the
input/output on the Transverter.
(See Figure 4.)
8. Run the downlead to the PS-0200
power supply connector labeled
“To Ant”. (See Figure 5.)
9. Run a cable from the PS-0200
power supply connector labeled
“To Set” to the set-top. (See
Figure 5.)
5. Slide the mounting brackets and “L” Bolts into the bracket
channels on the backside of the Transverter. (See Figure 2.)
Mounting
Bracket
“L” Bolt
Figure 2
Input/Output
-20dB Test
Figure 3
0-20 dB
Attn.
Downstream
To “Ant”
To “Set” Figure 5
Bracket
Chan-
nels
DS-1000 Mount Figure 4
Page 4.
Figure 3
4. Place the “L” bracket on the back of the antenna.
Insert two carriage bolts from the front (figure 4)
to attach. Secure on the back with the lock
washers and nuts. (See Figure 5).
5. Re-check the dipole feed assembly for the proper polarity.
(See Figures 1 & 2).
Figure 4
Sub-reflector
Page 9.

INSTALLATION / ASSEMBLY
with 18T-2127 Response Antenna
1. Place the sub-reflector on the
front of the feed and secure
with the #6 x 1/2" stainless
screw. (See Figure 1).
2. Determine the polarity of the
antenna. (See figures 2 & 3).
Figure 1
Sub-reflector
Figure 2 Figure 3
Horizontal Polarity
Vertical Polarity
Page 5.
1. Assemble the two halves
inserting the 4 #8-32
machine screws through
the front. Secure with
the keps nuts on the back.
(See Figure 3).
Vertical Polarity
Figure 2
Note: Loosely tighten
all hardware until
completely assembled
and then tighten
securely.
INSTALLATION / ASSEMBLY
with 26T-2127 Response Antenna
Horizontal Polarity:
Refer to (figure 1) for proper feed
alignment.
Vertical Polarity:
Refer to (figure 2) for proper feed
alignment.
3. Determine the polarity of
the antenna.
(See Figures 1 & 2).
2. Place the sub-reflector on
the front of the feed and
secure with the #6 x 1/2”
stainless screw. (See
Figure 4).
Figure 1
Horizontal Polarity
Page 8.
Model 18T-2127
Model 18T-2127
Model 18T-2127

Mast Clamp
U-Bolt Figure 6
“L” Bracket
Lock Washers & Nuts Figure 5
Figure 4
Tilt Holes
Tilt Slot
3. Place the "L" bracket on the back of
the antenna. Secure the feed on the
front with two carriage bolts. Secure
the feed on the back with the lock
washers and nuts. (See Figure 4).
4. Place the mast clamp on the U-bolt.
(See Figure 6.) Fasten the U-bolt on
the “L” bracket with 2 lockwashers
and nuts. (See Figure 5).
Note: Fixed tilt holes provide
antenna elevation up to
600 in 100 increments.
(See Figure 6).
Use the flat plate washer
on the adjustable tilt slot to
secure the antenna to the
requiredelevation.
(See Figure 7)
Tilt Slot
Figure 7
5. Connect the GPS Antenna to
the GPS port on the
Transverter. (See Figure 8)
6. Connect the 18T-2127
antenna output to the an-
tenna port on the side of the
Transverter. (See Figure 8)
7. Mount the Transverter on the
mast by sliding the mounting
brackets and “L” Bolts into
the bracket channels on the
backside of the Transverter.
(See Figure 10.)
Page 6.
GPS Antenna
GPS Port
Antenna Port
(located on side
of transverter)
Mounting
Bracket
“L” Bolt
Figure 10
Bracket
Chan-
nels
Input/Output
-20dB Test
Figure 9
0-20 dB
Attn.
Downstream
To “Ant”
To “Set” Figure 11
Figure 8
8. Connect the downlead cable to the
input/output on the Transverter.
(See Figure 9.)
9. Run the downlead to the PS-0200
power supply connector labeled
“To Ant”. (See Figure 11.)
10. Run a cable from the PS-0200
power supply connector labeled
“To Set” to the set-top. (See
Figure 11.)
Page 7.