Klark Teknik DN 30T User manual
(1) Headphone output – Connect a pair of
headphones via ⁄" TRS cable. The volume can be
adjusted with the adjacent LEVEL knob.
(2) SYNC LED – The LED will light red when the unit
is powered on, and light green when the unit is
connected to an Ethernet network. A ashing green
LED indicates that the unit is in master clock mode,
and solid green indicates slave mode.
(3) SYS LED – The LED will light red while the unit
is booting up. Once Dante becomes active,
the LED will light green.
(4) SIGNAL LEDs – The left and right LEDs will light
green when signal is present on each channel.
The LEDs will light red when the input signal
approaches clipping.
(5) ETHERCON LEDs – The left LED lights green to
indicate data trac, and the right LED lights to
indicate successful Ethernet connection.
(6) ETHERCON port – Connects the unit to a Dante
network via CAT5e or CAT6 cable. Power can also
be supplied via this connection.
(7) ON LED – Lights when power is connected via the
included 24 V power adapter.
(8) PoE LED – Lights when the unit is receiving power
via the Ethernet port.
(9) DC INPUT – Connect the included power adapter if
you don’t plan to use PoE.
(10) EARTH LIFT – Removes the ground/earth
connection to remove unwanted noise.
(11) OUTPUT L/R – Connect to a mixing console or audio
interface via balanced XLR cables.
(12) INPUTS – Connect an audio source via balanced
or unbalanced ¼" cables, RCA cables, or a stereo
⁄" cable. All inputs are wired in parallel with one
another.
(13) LEVEL – Adjusts the level of all input jacks. Start
with the knob at the center 12:00 position and turn
up if more signal is needed. Turn the knob down if
the SIGNAL LEDs light solid red.
DN 30T/DN 30R
2-Channel Dante Audio Receiver/Transmitter for High-Performance Networking
(1) (2)(3) (5) (5) (6) (7)(2) (9)(3) (8)
(10) (9) (4) (13)(11) (12)
DN 30R DN 30T
(7)
(6)
(8)
Specications
DN 30R DN 30T
Connectors
Ethernet 1 x RJ45 1 x RJ45
Analogue audio inputs —
2 x ¼" TRS, 40 k balanced,
20 k unbalanced
2 x RCA, 20 k unbalanced
1 x ⁄" TRS stereo,
20 k unbalanced
Max. input level — +22 dBu (sensitivity 0 dBu)
Analogue audio outputs
2 x XLR, 75 balanced
⁄" TRS, stereo,
20 unbalanced
—
Max. output level +22 dBu —
Phones 1 x ⁄" TRS, stereo —
Controls
Level 0 to -∞ dBu, adjustable
(phones only)
Sensitivity -20 to +20 dB,
adjustable
LED indicators Sync, Sys, On, PoE Signal, Sync, Sys, On, PoE
System
Frequency response 20 Hz to 20 kHz (±0.1 dB)
THD + N @ 1 kHz 0.0015% unweighted 0.0014% unweighted
Signal-to-noise ratio 98 dB 97 dB
Sample rate 44.1, 48, 88.2, 96 kHz
Dynamic range 116 dB unweighted
Crosstalk LR -110 dB -100 dB
Power adapter 24 V DC, 300 mA, center positive
Physical
Dimensions (H x W x D)
Without bumpers 54 x 108 x 103 mm (2.1 x 4.3 x 4.1")
With bumpers 63 x 118 x 112 mm (2.5 x 4.6 x 4.4")
Weight 0.7 kg (1.5 lbs)
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suered by any person who
relies either wholly or in part upon any description, photograph, or statement contained
herein.Technical specications, appearances and other information are subject to
change without notice. All trademarks are the property of their respective owners.
Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic,TC Helicon,
Behringer, Bugera and Coolaudio are trademarks or registered trademarks of Music Tribe
Global Brands Ltd. © Music Tribe Global Brands Ltd. 2019 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information
regarding Music Tribe’s Limited Warranty, please see complete details online at
musictribe.com/warranty.
Zhongshan Eurotec Electronics Limited
No. 10 Wanmei Road, South China Modern Chinese Medicine Park, Nanlang Town,
528451, Zhongshan City, Guangdong Province, China
FEDERAL COMMUNICATIONS
COMMISSION COMPLIANCE
INFORMATION
Responsible Party Name: Music Tribe Commercial NV Inc.
Address: 5270 Procyon Street
Las Vegas, NV 89118
Phone Number: +1 702 800 8290
DN 30T/DN 30R
complies with the FCC rules as mentioned in the followingparagraph:
This equipment has been tested and found to comply with the limits for a ClassB
digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected
• Consult the dealer or an experienced radio/TV technician forhelp
This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Caution!
Any changes or modications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Klark Teknik
DN 30T/DN 30R
This manual suits for next models
1
Other Klark Teknik Receiver manuals
