Connect NFT4872 User manual

154 lbs
0°/90°
Ax8 Bx 4 Cx4
x8
A
47.24 - 68.89 inches
①
⑤
④
③
②
x1
I
Dx6 Ex4 Fx8 Gx4 Hx8 I x1/1
⑦
⑧
⑥
+
4x4
x4
Gx1 I
4x4
1
2
x4
E
⑨
72x30x1 inches
< The pictures below are for reference only, please refer to the actual product. >
Please read this product manual carefully before use, and keep it properly.
Technical Data
Max. Load Capacity
Max. Desktop Size
Width Range
Tilting Angle
Product List
Accessory List
Attention: The drawings below are for guidance only and they may differ slightly from the product and
fittings received. Please contact customer service if there are any missing tools or installation problems.
Install on carpet to prevent scratches. Bring your own Phillips screwdriver or pistol drill.
Need two or more people to cooperate together.
Preparation before installation
or
Part List
No. Part PartNo.
Beam connecting
rod x2 Foot x2
Beam x4 Caster (2 with brake) x4 /
Allen key x1
Supporting plate
component x1 Cable tie x6
Spout plug x4 Foot pad x4
Lifting column x2
Installation Instruction
Installation Steps
Install Feet
STEP1
STEP2 Assembly beam
Insert
Pretighten the screw after
stretching to the proper position.
ITEM NO.: NFT4872
Installation guide

x4
Hx1 I
5x5
x4
Hx1 I
5x5
x4
E
STEP3 Install the beam
STEP4 Install supporting plate component
Tighten the screw H
Tighten the
screw B
Cover the
spout plug
Spout plug
STEP6 Install Casters or Leveling Glides
The front wheels are with brakes.
Handle Instructions
Please adjust the handle according to actual needs. While
turning the handle upwards, press the table with both hands
to turn it to a vertical angle. Release the handle. When you
hear a "pop", it means that the table is locked and the
adjustment is completed.
0°
90°
When adjusting the table,
please check whether there
are objects placed on the
table to avoid damage.
There's spare parts in the package, which will lead to asphyxia if swallowed by accident. Please
keep out of the reach of children for the spare parts.
Make sure you have read and comprehend the manual for installation. Please contact the
specialized persons if there's any confusion in the steps.
Children are forbidden to play on the product because of unforeseen action when playing, so any
dangerous consequences caused by this improper action will not be on
This appliance can be used by children aged from 7 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been given
supervision or instruction concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance.
Children must not perform cleaning and user maintenance without supervision.
Please make sure there is no hazard sources in your operating environment. e.g., do not litter the
tools around. Always be careful to treat the packaging materials in order to avoid any possible
danger, e.g. plastic bag may lead to choking hazard to children.
Keep the original package of the equipment if necessary in case of the future use in transportation.
Warning
This marking indicates that this product should not be disposed with other
household wastes. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources. To return your used device, please use
the return and collection systems or contact the retailer where the product was
purchased. They can take this product for environmental safe recycling.
F F
⑧
⑧
⑧
C
x1
I
4x4
x8
F
x4
C
STEP5 Install the tabletop
Self-prepared
Tear off Fix
Manage
Install the tabletop Cable ties ⑧
can be used to fix the
connecting wires on the table
to keep the cables tidy.
Loosen the screws and adjust the beam
length according to the table width.
Remarks: It is recommended that the distance between
the base and edge of the top is no more than 3 inches
on each side. Maximum top width 72 inches.
The cable must run down the center of the
support beam so it does not pinch when
top is installed.
Use Casters to make unit Mobile
or Glides for Stationary Unit