CONSET BSR 101 Quick setup guide

1
IMPORTANT!
INFORMATION ABOUT THE USE OF ELECTRICAL
HEIGHT ADJUSTABLE CHANGING TABLE
 Never leave the child unattended on the changing
table
 The remote should be placed out of reach of small
children. Switch off after use
 Be aware of other children in the room while in
use
 Be aware of things placed underneath the
changing table
 Changing table only to be used by the staff
 Please read the complete manual and remember
to instruct new staff about the use of the changing
table
TO BE PLACED NEARBY THE CHANGING TABLE

2
ELECTRIC HEIGHT ADJUSTABLE CHANGING TABLE
ConSet® - Type BSR 101+103+121
DIRECTIONS FOR USE / ASSEMBLING
IMPORTANT NOTES!
Prior to installment, use and maintenance of the table frame, any installer and any user of the changing table
must study this assembly and operation manual carefully, so as to gain a complete understanding of its
contents.
EN
WARNING
33
2
8
7
0
.
0
B
S
R 121
BSR 101/103

3
TABLE OF CONTENT
1. SAFETY AND WARNINGS
2. USAGE
3. SET UP AND INSTALLATION
4. OPERATION
5. MAINTENANCE AND DEFECTS
6. TECHNICAL DATA
7. PARTS
8. ASSEMBLY DIRECTIONS
9. DECLARATION OF CONFORMITY
1. SAFETY AND WARNINGS
2. GUIDELINES REGARDING ASSEMBLY AND USAGE
Usage:
 The electrical height adjustable changing table is designed to be used indoors in a dry atmosphere
(0-40°C; 20-90% relative humidity)
 For children 0-36 months.
 The changing table height is infinitely adjustable so that it can be set to the most ergonomically suitable
working level of the staff in a day care center or public day care
 They have not been designed for other purposes than those included in this manual, e.g. they are not to
be used in areas of high humidity or dampness, nor for lifting adults. Any other use is at one’s own risk!
Safety routines:
 Never leave the child unattended on the changing table
 THE REMOTE should be placed out of reach of small children. Switch off after use.
 Be aware of other children in the room while in use. Do not crawl, lie or move around under the changing
table.
 When placing the changing table always maintain a safe distance from other furnishings to avoid pinch
points.
 The changing table is only to be used by the staff. The changing table is a work station, not a toy.
 The remote control must not be used if there are any signs of damage or excessive wear and tear.
 If changing tables are mounted side by side a partition wall should be mounted to minimize risk of pinch
points.
Liability:
The manufacturer accepts under no circumstances warranty claims or liability claims for damages arising
from the improper use or handling of the table frame other than that described in this
operations manual.
This changing table complies with the prescribed safety regulations. Inappropriate use may cause
damage to persons and table.
Please read the operation manual prior to using the changing table. It provides you with important
information about safety, use, installation and maintenance of the table, and thus protecting you
and your children to avoid injury or damage to the table.
Please keep this operation manual and pass it on to any future owner!

4
3. SETUP AND INSTALLATION
The changing table must be mounted by a skilled fitter or craftsman. All directions of this manual must be
followed carefully.Upon assembly, the fitter must place page 1 of this manual near the changing table.
4. OPERATION
Push the buttons to adjust the height. When the button is no longer pushed, the changing table will stop.
5. MAINTENANCE AND DEFECTS
 The changing table i s only to be mai ntained with a wrung cloth. The changing table can under no
circumstances be hosed down.
 In the event of the occurrence of jarring sounds during operation, STOP using the table immediately.
6. TECHNICAL DATA
Frame, materials: Steel, powdercoated
F
MAX
= Max. load on changing table 70 kg
Operation: Up/down push button
Voltage:
Consumption:
Standby consumption:
100-240 VAC / 50-60Hz
80 Watt
< 1 watt
UP
DOWN

5
7. ASSEMBLY INSTRUCTIONS FLOOR TYPE BSR 101-103
a)Assemble foot and top support
b) Assemble top in pre drilled holes

6
c) Mount control box (white), power supply (black) and handset
d) Mount the wire basket in pre drilled holes
Important! The
handset must be
placed out of reach of
children. It is the
fitter’s responsibility
that this is the case!
The changing table is now ready for use.
The fitter must instruct the staff in the proper use
and the instructions of this manual.

7
8. ASSEMBLY INSTRUCTIONS WALL TYPE, BSR 121
a)Assemble wall brackets and top support
b) Assemble top in predrilled holes

8
c) Mount control box (white), power supply (black) and handset
d) Mount the wire basket in pre drilled holes
Important! The
handset must be
placed out of reach of
children. It is the
fitter’s responsibility
that this is the case!
The changing table is now ready for use.
The fitter must instruct the staff in the proper use
and the instructions of this manual.

9
9. DECLARATION OF CONFORMITY
We hereby declare, under our sole responsibility that the following products:
- ConSet changing table type BSR
which are covered by this statement, are in conformity with the following standards and other normative
documents::
- Council Directive 98/37/EF
- Council Directive 89/336/EØF with later changes
- Council Directive 73/23/EØF with later changes
With reference to the Machinery Directive (98/37/EF) please be aware:
- The changing table is considered a machine and
- The changing table may not be used until it has been assembled and installed according to the
instructions.
Manufacturer:
ConSet A/S
Stålvej 14-16
DK-6900 Skjern
Danmark
Tel: [phone], Fax: [phone]
www.conset.com
[email protected]