Contec PIO-64L(PCI)H User manual

1PIO-64/64L(PCI)H, PI-128L(PCI)H, PO-128L(PCI)H
Ver.1.00
Digital I/O Board with Opto-Isolation for PCI
PIO-64/64L(PCI)H
Digital Input Board with Opto-Isolation for PCI
PI-128L(PCI)H
Digital Output Board with Opto-Isolation for PCI
PO-128L(PCI)H
with Driver Library [API-PAC(W32)]
This board is a PCI-compliant interface board for input/output of
digitalsignals.
The board can input the open/closed circuit states of switches and
can control relays.
< PIO-64/64L(PCI)H > can input and output up to 64 channels.
< PI-128L(PCI)H > can input up to 128 channels.
< PO-128L(PCI)H > can output up to 128 channels.
Using the bundled Driver Library [API-PAC(W32)], you can create
Windows application software for this board in your favorite
programming language supporting Win32 API functions, such as
Visual Basic or Visual C/C++.
Features
- Common power-supply configuration in 16 channel units, capable of supporting different external power supplies.
- Opto-coupler used to electrically isolated I/O signal interface from the PCI bus, offering good noise immunity.
- Capable of using up to 16 channels of input signals as interrupt inputs.
Also capable of selecting the input signal edge for generating interrupts
< PIO-64/64L(PCI)H >, < PI-128L(PCI)H >
- Digital filtering that prevents input signal noise and chattering.
< PIO-64/64L(PCI)H >, < PI-128L(PCI)H >
- Up to 35VDC, 100mA per signal, max. output.
< PIO-64/64L(PCI)H >, < PO-128L(PCI)H >
- Zener diode connected to output transistors for protection from surge voltage. Over-current protective device provided for every eight channels
of output transistors.
< PIO-64/64L(PCI)H >, < PO-128L(PCI)H >

2PIO-64/64L(PCI)H, PI-128L(PCI)H, PO-128L(PCI)H
Ver.1.00
Specification
Item Specifications
Input
Type Opto-Isolated Input (for current sinking output)
(Negative logic *1)
Number of Channels 128 channels
(16 of these 128 can be used as interrupt signal)
(16 channels share a positive common)
Resister 4.7kΩ
Current required to turn ON 2.0mA(Min.)
Current required to turn
OFF
0.16mA(Max.)
Interrupts Combine four interrupt signals to one interrupt
request signal as the INTA.
Either rising edge or falling edge of input signal can
generate interrupt.
Response time 200μsec(Max.)
Common
I/O address Any 32-byte boundary
Interrupt level 1 level use
Boards in one system Maximum of 16 boards can be install in a same system.
Isolated voltage 250Vrms
External power supply 12 - 24VDC(±10%)
Power consumption 5VDC 500mA(Max.)
Operating condition 0 - 50°C, 10 - 90%RH (No condensation)
Connecting distance 50m(Typ.)(depending on wiring environment)
PCI bus specification 32bit, 33MHz, Universal key shapes supported *2
Dimension (mm) 176.41(L) x 106.68(H)
Weight 215g
*1 Data “0” and “1” correspond to the High and Low levels, respectively.
*2 This board requires power supply at +5V from an expansion slot
(it does not work on a machine with a +3.3V power supply alone).
Item Specifications
Output
Type Opto-Isolated Open Collector Output (current sinking
type)
(Negative logic *1)
Number of Channels 128 channels (16 channels share a negative common)
Voltage 35VDC(Max.)Rate
Current 100mA/channel (Max.)
Residual voltage with output
on
0.5V or less (Output current ≤50mA),
1.0V or less (Output current ≤100mA)
Surge protector Zener diode RD47FM(NEC)
Response time 200μsec(Max.)
Common
I/O address Any 32-byte boundary
Interrupt level not use
Boards in one system Maximum of 16 boards can be install in a same system.
Isolated voltage 250Vrms
External power supply 12 - 24VDC(±10%)
Power consumption 5VDC 500mA(Max.)
Operating condition 0 - 50°C, 10 - 90%RH (No condensation)
Connecting distance 50m(Typ.)(depending on wiring environment)
PCI bus specification 32bit, 33MHz, Universal key shapes supported *2
Dimension (mm) 176.41(L) x 106.68(H)
Weight 215g
*1 Data “0” and “1” correspond to the High and Low levels, respectively.
*2 This board requires power supply at +5V from an expansion slot
(it does not work on a machine with a +3.3V power supply alone).
Item Specification
Input
Type Opto-Isolated Input (for current sinking output)
(Negative logic *1)
Number of Channels 64 channels
(16 of these 64 can be used as interrupt signal)
(16 channels share a positive common)
Resister 4.7kΩ
Current required to turn ON 2.0mA(Min.)
Current required to turn
OFF
0.16mA(Max.)
Interrupts Combine four interrupt signals to one interrupt
request signal as the INTA.
Either rising edge or falling edge of input signal can
generate interrupt.
Response time 200μsec(Max.)
Output
Type Opto-Isolated Open Collector Output (current sinking type)
(Negative logic *1)
Number of Channels 64 channels (16 channels share a negative common)
Voltage 35VDC(Max.)Rate
Current 100mA/channel (Max.)
Residual voltage with output
on
0.5V or less (Output current ≤50mA),
1.0V or less (Output current ≤100mA)
Surge protector Zener diode RD47FM(NEC)
Response time 200μsec(Max.)
Common
I/O address Any 32-byte boundary
Interrupt level 1 level use
Boards in one system Maximum of 16 boards can be install in a same system.
Isolated voltage 250Vrms
External power supply 12 - 24VDC (±10%)
Power consumption 5VDC 500mA(Max.)
Operating condition 0 - 50°C, 10 - 90%RH (No condensation)
Connecting distance 50m(Typ.)(depending on wiring environment)
PCI bus specification 32bit, 33MHz, Universal key shapes supported *2
Dimension (mm) 176.41(L) x 106.68(H)
Weight 215g
*1 Data “0” and “1” correspond to the High and Low levels, respectively.
*2 This board requires power supply at +5V from an expansion slot
(it does not work on a machine with a +3.3V power supply alone).
[mm]
The standard outside dimension (L) is
the distance from the end of the board
to the outer surface of the slot cover.
176.41(L)
106.68(H)

3PIO-64/64L(PCI)H, PI-128L(PCI)H, PO-128L(PCI)H
Ver.1.00
Support Software
You should use CONTEC support software according to your
purpose and development environment.
API-PAC(W32) is the library software that provides the commands
for CONTEC hardware products in the form of Windows standard
Win32 API functions (DLL). It makes it easy to create high-speed
application software taking advantage of the CONTEC hardware
using various programming languages that support Win32 API
functions, such as Visual Basic and Visual C/C++.
It can also be used by the installed diagnosis program to check
hardware operations.
CONTEC provides download services to supply the updated drivers
and differential files.
For details, read Help on the bundled CD-ROM or visit the
CONTEC's Web site.
< Operating environment >
OS Windows XP, 2000, NT, Me, 98, etc..
Adaptation language Visual C/C++, Visual Basic, Delphi, Builder,
etc..
This driver is used to control CONTEC digital I/O boards (cards)
from within Linux.
You can control CONTEC I/O boards easily using the shared library
used by gcc and Kylix, the device driver (module) for each kernel
version, and the board (card) configuration program (config).
CONTEC provides download (at http://www.contec.com/comm/)
services to supply the updated drivers and differential files.
For details, read Help on the bundled CD-ROM or visit the
CONTEC's Web site.
< Operating environment >
OS RedHatLinux, TurboLinux, etc..
(For details on supported distributions, refer
to Help available after installation.)
Adaptation language gcc, Kylix, etc..
This is a VI library to use in National Instruments LabVIEW.
VI-DAQ is created with a function form similar to that of LabVIEW's
Data Acquisition VI, allowing you to use various devices without
complicated settings.
See http://www.contec.com/vidaq/ for details and download of VI-
DAQ.
Cable & Connector
Connection Conversion Shield Cable (100P 96P)
: PCB100/96PS-1.5 (1.5m)
: PCB100/96PS-3 (3m)
: PCB100/96PS-5 (5m)
Flat Cable with One 100-Pin Connector
: PCA100P-1.5(1.5m)
: PCA100P-3(3m)
: PCA100P-5(5m)
Connection Conversion Shield Cable (100pin 37pin D-SUB x 2)
: PCB100WS-1.5(1.5m)
: PCB100WS-3(3m)
: PCB100WS-5(5m)
Product Configuration List
- Board
[PIO-64/64L(PCI)H, PI-128L(PCI)H, or PO-128L(PCI)H] ... 1
- First step guide ... 1
- CD-ROM *1 [API-PAC(W32)] ... 1
*1 The CD-ROM contains the driver software and User's Guide (this
guide)
Accessories
Screw Terminal : EPD-96 *1
Digital I/O 64CH Series Terminal Panel : DTP-64(PC) *1
96pin half 37pin D-SUB(Female) x 2 conversion terminal
: CCB-96 *1
Signal Monitor for Digital I/O(64Bits) : CM-64(PC)E *1
Termination panel with Screw Terminals for Spade Lugs
: DTP-3(PC) *2
Termination panel with Screw Terminals : DTP-4(PC) *2
Relay Terminal Unit for Crimping : EPD-37 *2
Relay Terminal Unit for Crimping : EPD-37A *2
*1: A PCB100/96PS optional cable is required separately.
*1: A PCB100WS optional cable is required separately.
* Check the CONTEC's Web site for more information on these
options.

4PIO-64/64L(PCI)H, PI-128L(PCI)H, PO-128L(PCI)H
Ver.1.00
Using the On-board Connectors
To connect an external device to this board, plug the cable from the device into the interface connector (CAN,CNB) shown below.
- Connector used
HDRA-E100W1LFDT1EC-SL
(mfd.by HONDA)equivalent
- Applicable connector
HDRA-E100MA1(mfd.by HONDA)
Interface connector
CNACNB
P-A/B
P-A/B
O-B7
O-B6
O-B5
O-B4
O-B3
O-B2
O-B1
O-B0
O-A7
O-A6
O-A5
O-A4
O-A3
O-A2
O-A1
O-A0
N-A/B
N-A/B
N-A/B
N-A/B
N-A/B
N-A/B
N.C.
N.C.
P-8/9
P-8/9
O-97
O-96
O-95
O-94
O-93
O-92
O-91
O-90
O-87
O-86
O-85
O-84
O-83
O-82
O-81
O-80
N-8/9
N-8/9
N-8/9
N-8/9
N-8/9
N-8/9
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
P-E/F
P-E/F
O-F7
O-F6
O-F5
O-F4
O-F3
O-F2
O-F1
O-F0
O-E7
O-E6
O-E5
O-E4
O-E3
O-E2
O-E1
O-E0
N-E/F
N-E/F
N-E/F
N-E/F
N-E/F
N-E/F
N.C.
N.C.
P-C/D
P-C/D
O-D7
O-D6
O-D5
O-D4
O-D3
O-D2
O-D1
O-D0
O-C7
O-C6
O-C5
O-C4
O-C3
O-C2
O-C1
O-C0
N-C/D
N-C/D
N-C/D
N-C/D
N-C/D
N-C/D
CNB
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
I-40
I-41
I-42
I-43
I-44
I-45
I-46
I-47
I-50
I-51
I-52
I-53
I-54
I-55
I-56
I-57
P-4/5
P-4/5
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
I-60
I-61
I-62
I-63
I-64
I-65
I-66
I-67
I-70
I-71
I-72
I-73
I-74
I-75
I-76
I-77
P-6/7
P-6/7
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
I-00
I-01
I-02
I-03
I-04
I-05
I-06
I-07
I-10
I-11
I-12
I-13
I-14
I-15
I-16
I-17
P-0/1
P-0/1
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
I-20
I-21
I-22
I-23
I-24
I-25
I-26
I-27
I-30
I-31
I-32
I-33
I-34
I-35
I-36
I-37
P-2/3
P-2/3
CNA
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
* I-00 - I-17 can be used as interrupt signal.
Common plus pin for
+E/+F output ports
+F port (Output)
+E port (Output)
+D port (Output)
+C port (Output)
Common minus pin for
+E/+F output ports
Common plus pin for
+C/+D output ports
Common minus pin for
+C/+D output ports
Common plus pin for
+A/+B output ports
+B port (Output)
+A port (Output)
+9 port (Output)
+8 port (Output)
Common minus pin for
+A/+B output ports
Common plus pin for
+8/+9 output ports
Common minus pin for
+8/+9 output ports
+5 port (Input)
+4 port (Input)
+6 port (Input)
+7 Port (Input)
Common plus pin for
+6/+7 input ports
Common plus pin for
+4/+5 input ports
+0 port (Input)
+1 port (Input)
Common plus pin for
+0/+1 input ports
Common plus pin for
+2/+3 input ports
+3 Port (Input)
+2 Port (Input)
P-0/1 - P-6/7 Connect the positive side of the external power supply. These pins are common to 16 input
signal pins.
P-8/9 - P-E/F Connect the positive side of the external power supply. These pins are common to 16 output
signal pins.
N-8/9 - N-E/F Connect the negative side of the external power supply. These pins are common to 16 output
signal pins.
A current of 0.3 A is allowable per connector pin. Connect the required number of pins for the
total current for the corresponding 16 output signals.
N.C. This pin is left unconnected.

5PIO-64/64L(PCI)H, PI-128L(PCI)H, PO-128L(PCI)H
Ver.1.00
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
I-40
I-41
I-42
I-43
I-44
I-45
I-46
I-47
I-50
I-51
I-52
I-53
I-54
I-55
I-56
I-57
P-4/5
P-4/5
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
I-60
I-61
I-62
I-63
I-64
I-65
I-66
I-67
I-70
I-71
I-72
I-73
I-74
I-75
I-76
I-77
P-6/7
P-6/7
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
I-00
I-01
I-02
I-03
I-04
I-05
I-06
I-07
I-10
I-11
I-12
I-13
I-14
I-15
I-16
I-17
P-0/1
P-0/1
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
I-20
I-21
I-22
I-23
I-24
I-25
I-26
I-27
I-30
I-31
I-32
I-33
I-34
I-35
I-36
I-37
P-2/3
P-2/3
CNA
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
P-A/B
P-A/B
I-B7
I-B6
I-B5
I-B4
I-B3
I-B2
I-B1
I-B0
I-A7
I-A6
I-A5
I-A4
I-A3
I-A2
I-A1
I-A0
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
P-8/9
P-8/9
I-97
I-96
I-95
I-94
I-93
I-92
I-91
I-90
I-87
I-86
I-85
I-84
I-83
I-82
I-81
I-80
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
P-E/F
P-E/F
I-F7
I-F6
I-F5
I-F4
I-F3
I-F2
I-F1
I-F0
I-E7
I-E6
I-E5
I-E4
I-E3
I-E2
I-E1
I-E0
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
P-C/D
P-C/D
I-D7
I-D6
I-D5
I-D4
I-D3
I-D2
I-D1
I-D0
I-C7
I-C6
I-C5
I-C4
I-C3
I-C2
I-C1
I-C0
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
CNB
* I-00 - I-17 can be used as interrupt signal.
Common plus pin for
+E/+F input ports
+F port (Input)
+E port (Input)
+D port (Input)
+C port (Input)
Common plus pin for
+C/+D input ports
Common plus pin for
+A/+B input ports
+B port (Input)
+A port (Input)
+9 port (Input)
+8 port (Input)
Common plus pin for
+8/+9 input ports
+5 port (Input)
+4 port (Input)
+6 port (Input)
+7 Port (Input)
Common plus pin for
+6/+7 input ports
Common plus pin for
+4/+5 input ports
+0 port (Input)
+1 port (Input)
Common plus pin for
+0/+1 input ports
Common plus pin for
+2/+3 input ports
+3 Port (Input)
+2 Port (Input)
I-00 - I-F7 128 input signal pins. Connect output signals from the external device to these pins.
P-0/1 - P-E/F Connect the positive side of the external power supply. These pins are common to 16 input signal pins.
N.C. This pin is left unconnected.

6PIO-64/64L(PCI)H, PI-128L(PCI)H, PO-128L(PCI)H
Ver.1.00
N-4/5
N-4/5
N-4/5
N-4/5
N-4/5
N-4/5
O-40
O-41
O-42
O-43
O-44
O-45
O-46
O-47
O-50
O-51
O-52
O-53
O-54
O-55
O-56
O-57
P-4/5
P-4/5
N.C.
N.C.
N-6/7
N-6/7
N-6/7
N-6/7
N-6/7
N-6/7
O-60
O-61
O-62
O-63
O-64
O-65
O-66
O-67
O-70
O-71
O-72
O-73
O-74
O-75
O-76
O-77
P-6/7
P-6/7
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
N-0/1
N-0/1
N-0/1
N-0/1
N-0/1
N-0/1
O-00
O-01
O-02
O-03
O-04
O-05
O-06
O-07
O-10
O-11
O-12
O-13
O-14
O-15
O-16
O-17
P-0/1
P-0/1
N.C.
N.C.
N-2/3
N-2/3
N-2/3
N-2/3
N-2/3
N-2/3
O-20
O-21
O-22
O-23
O-24
O-25
O-26
O-27
O-30
O-31
O-32
O-33
O-34
O-35
O-36
O-37
P-2/3
P-2/3
CNA
P-A/B
P-A/B
O-B7
O-B6
O-B5
O-B4
O-B3
O-B2
O-B1
O-B0
O-A7
O-A6
O-A5
O-A4
O-A3
O-A2
O-A1
O-A0
N-A/B
N-A/B
N-A/B
N-A/B
N-A/B
N-A/B
N.C.
N.C.
P-8/9
P-8/9
O-97
O-96
O-95
O-94
O-93
O-92
O-91
O-90
O-87
O-86
O-85
O-84
O-83
O-82
O-81
O-80
N-8/9
N-8/9
N-8/9
N-8/9
N-8/9
N-8/9
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
P-E/F
P-E/F
O-F7
O-F6
O-F5
O-F4
O-F3
O-F2
O-F1
O-F0
O-E7
O-E6
O-E5
O-E4
O-E3
O-E2
O-E1
O-E0
N-E/F
N-E/F
N-E/F
N-E/F
N-E/F
N-E/F
N.C.
N.C.
P-C/D
P-C/D
O-D7
O-D6
O-D5
O-D4
O-D3
O-D2
O-D1
O-D0
O-C7
O-C6
O-C5
O-C4
O-C3
O-C2
O-C1
O-C0
N-C/D
N-C/D
N-C/D
N-C/D
N-C/D
N-C/D
CNB
Common plus pin for
+E/+F output ports
+F port (Output)
+E port (Output)
+D port (Output)
+C port (Output)
Common minus pin for
+E/+F output ports
Common plus pin for
+C/+D output ports
Common minus pin for
+C/+D output ports
Common plus pin for
+A/+B output ports
+B port (Output)
+A port (Output)
+9 port (Output)
+8 port (Output)
Common minus pin for
+A/+B output ports
Common plus pin for
+8/+9 output ports
Common minus pin for
+8/+9 output ports
+5 port (Output)
+4 port (Output)
+6 port (Output)
+7 Port (Output)
Common plus pin for
+6/+7 output ports
Common plus pin for
+4/+5 output ports
Common minus pin for
+6/+7 output ports
Common minus pin for
+4/+5 output ports
+1 port (Output)
+0 port (Output)
+2 port (Output)
+3 Port (Output)
Common plus pin for
+2/+3 output ports
Common plus pin for
+0/+1 output ports
Common minus pin for
+2/+3 output ports
Common minus pin for
+0/+1 output ports
O-00 - O-F7 128 output signal pins. Connect input signals from the external device to these pins.
P-0/1 - P-E/F Connect the positive side of the external power supply. These pins are common to 16 output signal pins.
N-0/1 - N-E/F Connect the negative side of the external power supply. These pins are common to 16 output signal pins.
A current of 0.3 A is allowable per connector pin. Connect the required number of pins for the total
current for the corresponding 16 output signals.
N.C. This pin is left unconnected.

7PIO-64/64L(PCI)H, PI-128L(PCI)H, PO-128L(PCI)H
Ver.1.00
Connecting Input Signals
Connect the input signals to a device which can be current-driven,
such as a switch or transistor output device.
The connection requires an external power supply to feed currents.
The board inputs the ON/OFF state of the current-driven device as a
digitalvalue.
External CircuitBoard
Vcc
Vcc
opto-coupler
Input Pin
Input Pin
Plus
Common External
Power
Supply
12 - 24 VDC
Switch
* Input Pin: I-xx
Switch
opto-coupler
The input circuit of this board is illustrated in Figure 3.5. The on-
board opto-couplers isolate internal input circuits from outside
devices. The input channels are to be connected with current sinking
output signals. Driving these opto-isolated circuits require an
additional power supply isolated from the PC system. When a
12VDC external power is used, each input channel will consume
about 2.6mA current; when a 24VDC external power supply is
selected, each input channel will consume about 5.1mA current.
I-00 (CNA : 7 pin)
Common plus for input (CNA : 23 pin)
External
Power
Supply
12 - 24 VDC
+
-
Board
Switch
Connecting Output Signals
Connect the output signals to a current-driven controlled device such
as a relay or LED.
The connection requires an external power supply to feed currents.
The board controls turning on/off the current-driven controlled device
using a digital value.
External Circuit
Plus
Common
Output
Pin
Board
Vcc
Zener
diode
Poly Switch
* Output Pin: O-xx
External
Power
Supply
12 - 24 VDC
Output
Pin
Minnus
Common
Zener
diode
opto-isolated
opto-isolated
Load
Load
The output circuit of this board is illustrated in Figure 3.7. The
signal output section is an opto- isolated, open-collector output
(current sink type). Driving the output section requires an external
power supply.
The rated output current per channel is 100 mA at maximum.
The output section can also be connected to a TTL level input as it
uses a low-saturated transistor for output. The residual voltage
(low-level voltage) between the collector and emitter with the output
on is 0.5 V or less at an output current within 50 mA or at most 1.0
V at an output current within 100 mA.
A zener diode is connected to the output transistor for protection
from surge voltages. A PolySwitch-based over-current protector is
provided for every eight output transistors. When the over-current
protector works, the output section of the board is temporarily
disabled. If this is the case, turn of the power to the PC and the
external power supply and wait for a few minutes, then turn them on
back.
When the PC is turned on, all output are reset to OFF.
O-80 (CNB : 7 pin)
LED
5.1kΩ
Common pluus for output (CNB : 23 pin)
Board
Common Minus for output (CNB : 1 pin)
+
-
When “1” is output to a relevant bit, the corresponding LED comes on.
When “0” is output to the bit, in contrast, the LED goes out.
External
Power
Supply
12 - 24 VDC

8PIO-64/64L(PCI)H, PI-128L(PCI)H, PO-128L(PCI)H
Ver.1.00
Common plus
for output
Output
TTL Level Input
VCC
Input Board
GND
2kΩ
+
-
External
Power Supply
12 - 24 VDC
Common Minnus
for output
Connecting the Sink Type Output and
Sink Output Support Input
The following example shows a connection between a sink type
output (output board) and a sink output support input (input
board). Refer to this connection example when you connect such
boards to each other.
+
-
Output(Sink Type)
Input(Sink Output Support)
External
Power Supply
12 - 24 VDC
Input Board
Common plus
for output
Common Minnus
for output
Output Board
Common plus
for input
Block Diagram
Interrupt Control
Control Circuit
PIO-64/64L(PCI)H
External
Digital Input Port0
(8ch, Group0)
Opto-
coupler
Opto-
coupler
&
Transistor
PCI BUS*
External
Digital Input Port1
(8ch, Group1)
External
Digital Input Port2
(8ch, Group2)
External
Digital Input Port3
(8ch, Group3)
External
Digital Input Port4
(8ch, Group4)
External
Digital Input Port5
(8ch, Group5)
External
Digital Input Port6
(8ch, Group6)
External
Digital Input Port7
(8ch, Group7)
External
Digital Output Port8
(8ch, Group8)
External
Digital Output Port9
(8ch, Group9)
External
Digital Output PortA
(8ch, GroupA)
External
Digital Output PortB
(8ch, GroupB)
External
Digital Output PortC
(8ch, GroupC)
External
Digital Output PortD
(8ch, GroupD)
External
Digital Output PortE
(8ch, GroupE)
External
Digital Output PortF
(8ch, GroupF)

9PIO-64/64L(PCI)H, PI-128L(PCI)H, PO-128L(PCI)H
Ver.1.00
Interrupt
Control
PI-128L(PCI)H
PCI BUS*
Control
Circuit
Opto-
coupler
External
Digital Input Port0
(8ch, Group0)
External
Digital Input Port1
(8ch, Group1)
External
Digital Input Port2
(8ch, Group2)
External
Digital Input Port3
(8ch, Group3)
External
Digital Input Port4
(8ch, Group4)
External
Digital Input Port5
(8ch, Group5)
External
Digital Input Port6
(8ch, Group6)
External
Digital Input Port7
(8ch, Group7)
External
Digital Input Port8
(8ch, Group8)
External
Digital Input Port9
(8ch, Group9)
External
Digital Input PortA
(8ch, GroupA)
External
Digital Input PortB
(8ch, GroupB)
External
Digital Input PortC
(8ch, GroupC)
External
Digital Input PortD
(8ch, GroupD)
External
Digital Input PortE
(8ch, GroupE)
External
Digital Input PortF
(8ch, GroupF)
The specification, color, and design of a product may be changed without a preliminary announcement.
Control Circuit
PO-128L(PCI)H
Opto-
coupler
&
Transistor
PC I BUS*
External
Digital Output Port0
(8ch, Group0)
External
Digital Output Port1
(8ch, Group1)
External
Digital Output Port2
(8ch, Group2)
External
Digital Output Port3
(8ch, Group3)
External
Digital Output Port4
(8ch, Group4)
External
Digital Output Port5
(8ch, Group5)
External
Digital Output Port6
(8ch, Group6)
External
Digital Output Port7
(8ch, Group7)
External
Digital Output Port8
(8ch, Group8)
External
Digital Output Port9
(8ch, Group9)
External
Digital Output PortA
(8ch, GroupA)
External
Digital Output PortB
(8ch, GroupB)
External
Digital Output PortC
(8ch, GroupC)
External
Digital Output PortD
(8ch, GroupD)
External
Digital Output PortE
(8ch, GroupE)
External
Digital Output PortF
(8ch, GroupF)