Cooler Master GD160 ARGB User manual

GD160 ARGB
GD160 ARGB
33.8/38.2 kg
96 x 33 x 23 cm
7F., 398, Xinhu 1st Rd., Neihu Dist.,
Taipei City 114065,
Taiwan

GD160 ARGB

100 kg (220.5lbs)
160 x 75 cm (63.0” x 29.5”)
65 to 130 cm (25.6” to 51.2”)
GD160 ARGB
Model
Position
Materials
Lighting
Table Length x Width
Height Range (Dual Motor)
Max. Load
Cable Management Tray
Mouse Mat
Certifications
Deluxe Large
Chipboard, Aluminum, and Steel
ARGB (front & back)
Yes
Yes, 90 x 30 cm (35.4” x 11.8”)
• ANSI/BIFMA X5.5-2021
• EN527-1 and EN527-2
• CE, FCC, and RoHS
• REACH
• ISTA 3A (Package)
65 to 130 cm (25.6” to 51.2”)

M6 Screws for Connecting
Frame
Power Adapter & Cable
Tray
Cable Management Tray
Power Adapter
AC Power Plug
Control Panel
LED Power Cable (2 PIN)
Tabletop
LED Control Box
Micro USB to USB Cable
Communication Cable
4
8
24
4
1
1
1
1
1
1
1
1
1
1
1
1
6
2
2
2
2
2
2
M6 Screws for Lifting
Column
M6 Screws
M4 Screws
Cable Route
Feet
Lifting Columns
Left Supporting Beams
Right Supporting Beams
Side Brackets
Connecting Rods
Allen Key 4x4mm
Allen Key (with cross)
5x5mm
GD160 ARGB
N
O
P
Q
R
S
T
U
V
W
H
I
J
K
L
M
Cable a
Cable b

Installation diagram
1
2
3
Install supporting beams (J) (K) and side brackets (M)
Loosen
Insert
Insert
Tighten
Install lifting column (I)
Install feet (H)
GD160 ARGB
M
V
H
S
P
PK
U
J
L
N
Q
R
T
W
H
IO
E
A
L
K
A
M
M
K
J
L
I
E
B
B
E
C
C
H
K x 2
L x 2
M x 2
J x 2
E x 1
A x 4
B x 8
E x 1
I x 2
E x 1
H x 2
C x 8

Loosen
Adjust
Tighten
The adjustment of the support
beams cannot exceed past this hole.
Connect cables to the power adapter (P) and LED control box (U)
Interface for light strip
Install cable management tray (O)
Turn over the table and install the cable
management tray (O).
Install power adapter & cable tray (N)
Step7
Install tabletop (T), power adapter (P) and control panel (R)
GD160 ARGB
F
D
E
D
R
F
P
C
C
R
P
Q
w
V
U
S
Peel off Affix cables
Fix the cables to the tabletop
with cable route (G) to keep
the desk cables organized.
Sort cables
under
T
E
C
O
2
3
1
Buckle from
one side
Buckle from
the other
side
Tighten
N
Q
V
P
U
Port for lifting colums
Control panel
cable b
Control panel
cable a
W
S
G
STEP 2: Buckle power adapter &
cable tray (N)
STEP 1: Tighten the screw without
screwing them completely.
E x 1
C x 12
D x 4
F x 1
P x 1
R x 1
E x 1
C x 4
O x 1
E x 1
N x 1

Height USB Fast Charging
Complete
Operation Instructions
1. Product Outline
2. Product Specification
3. Operating Instructions
There are seven control options: "▲" , "▼" , "1" , "2" , "3" , "M" , "A"
(1) "▲" : Adjust the desk upwards
(2) "▼" : Adjust the desk downwards
(3) "1" : Position 1, first height position saved by the user
(4) "2" : Position 2, second height position saved by the user
(5) "3" : Position 3, third height position saved by the user
(6) "M" : Height memory function
(7) "A” : Press to switch the light effect
Height adjustable function:
Press the"▲" or "▼" button to adjust the height. The LED display shows the current
height.
●
●USB charging function:
a. USB output: QC2.0/QC3.0, 5.0V/9.0V/12.0V, ±5%, current: 1.5A
●Anti-collision sensitivity adjustment - optional features:
a. Press and hold the “▲” and “▼” buttons for 5 seconds simultaneously to switch the
sensitivity. Switch one file for 1 time and divide it into 4 files (A-3, A-2, A-1, A-0);
b. The display shows “ ” , the anti-collision function is off; the display shows “ ”,
low sensitivity; Display shows “ ”, medium sensitivity; display shows“ ”, high
sensitivity;
c. During height adjustment, when tabletop comes in contact with another object, it
instantly stops and reverses to avoid damage.
d. Press and hold the “▲” and “▼” button for 5 seconds simultaneously. If the display
does not display the above code, the anti-collision feature is disabled.
●Troubleshooting:
a. Reset: When the LED shows " "or " ", press “▼” button until the desk reaches its
lowest height and rebounds to stop, indicating that the reset has been finished.
b. When it doesn't work and the LED shows "E01" or "E02", please wait 18 minutes and
try again.
c. If LED display shows other codes and the “▼” button doesn't work, please check the
cable connection and then cut off the power for at least 10 seconds. Reconnect to the
power and press “▼” button . Then the LED display will show " " or " ".
Long press ”▼“ button to start the reset process.
d. If all the above do not work, please contact our customer service.
●Light effect switching function:
a. Short press “A”button to switch the light effect; overall seven types.
0: Spectrum;
1: Reload;
2: Recoil;
3. Breathing;
4. Refill;
5. Custom mode;
6. Turn off;
b. Long press “A”button for three seconds to turn off the light.
c. Long press “A”button for three seconds after turning off the light to turn it on again.
GD160 ARGB
Height memory function:
a. Press UP or DOWN button and adjust the height to the desired height. Press "M" to
save the height, and the screen will display " ";
Press "1", "2", or "3" and save the height to the corresponding number of 1 or 2 or 3,
which will then display on the screen as " ", " ", or " ";
b. Press "1", "2" and "3" button directly to automatically adjust the height you saved.
●

Attention
1. Power supply: AC100V-240V, 50/60Hz
2. Service Environment: 0-40℃
3. Unplug the power plug before cleaning, wipe the dust on surface with slight wet
dishcloth when cleaning, be careful not to allow any wet drops reach internal parts.
4. The electric box contains electronic components, metals, plastics, wires etc., so
dispose of it in accordance with each country's environmental legislation, and not
with general household waste.
5. Check carefully to ensure correct and complete assembly before using.
6. Be familiar with all functions and program settings of the product before first use.
7. Children are forbidden to play on the product because of unforeseen action when
playing, so any dangerous consequences caused by this improper action will not be on
manufacturers.
8. Slight noise caused by the V-ribbed belt or brake system due to structure will not
have any effect on the use of the equipment.
9. Corrosive or abrasive materials are forbidden to clean the equipment. Must ensure
that the cleaner used will not pollute the environment.
10. This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved. Children shall not play
with the appliance.
The following tips will help you detect and fix common issues. If the error you've run
into is not listed below, please contact with your supplier. Only the manufacturer and
professionals are capable for investigating and correcting these issues.
MethodIssue
Common Issues
11. Cleaning and user maintenance shall not be made by children without supervision.
12. If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or a similarly qualified person in order to avoid a hazard.
13. Please make sure there is no hazard sources in your operating environment. e.g.,
do not litter the tools around. Always be careful to treat the packaging materials in order
to avoid any possible danger, e.g. plastic bag may lead to choking hazard to children.
14. Keep the original package of the equipment if necessary in case of the future use in
transportation.
Waste disposal
This marking indicates that this product should
not be disposed with other household wastes.
To prevent possible harm to the environment or
human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable
reuse of material resources. To return your used
device, please use the return and collection
systems or contact the retailer where the
product was purchased. They can take this
product for environmental safe recycling.
GD160 ARGB
The desktop will not function
Table rises very slowly
The desk moves downwards
without any operation
Automatically self resets
Table is able to move downwards,
but not upwards; or vice-versa
The table does not reach its
highest or lowest position
The desk cannot rise
Overwork
(Duty cycle: Max 2min on/
18min OFF)
Check if all the cables well connected;
Check if overloaded,
max loading: 100 kg (220.5lbs)
Reset;
Restart after suspend for 18mins while
connecting with power.

GD160 ARGB

GD160 ARGB