coov N100 Plus User manual

N100 Plus Instruction Manual
Content：
Ⅰ、Before use
Ⅱ、Wireless A Mode
Ⅲ、Wireless B Mode(Default Mode)
Ⅳ、Wired Connection
Ⅴ、PC end Joypad use
Ⅵ、COOV assistant PC side
Ⅶ、Firmware/script update
Ⅷ、QuickMacro
A、Button mapping
B、Burst (off by default)
C、Auto combo
D、Auto infinite loop function (off by default)
E、Joypad vibration switch and force adjustment function
F、Four sets of independent configuration switching
G、Calibration function
H、Linear control (on by default)

Ⅰ、Before use
Before use, please go to Switch Host "System Settings" - "Controllers and Sensors" - "Pro
Controller Wired Communication" is set to "On".
Note: Wireless A mode (The indicator light is blue) and wireless B mode (The
indicator light is green) can be switched by long pressing the pairing button for 5
seconds.
After the N100 Plus is successfully connected, there is no need to enter the
“Joypad”-“change grip/sequence” interface, otherwise the handle will be
automatically disconnected. Press the N100 Plus pairing button and the handle will
resume operation.
Ⅱ、无线 A模式
N100 Plus Bluetooth Wireless Connection Switch.The indicator light is blue.

1. Go to the Switch and set the "Controllers and Sensors" - "Change Grips / Order"
interface.
2. Connect the Joypad to the N100 Plus.
3. Connect the N100 Plus to a power source or a charging treasure (powering the N100
Plus).
4. The N100 Plus indicator 1 flashes blue.
5. After the connection prompt appears on the interface, press the ENTER button（NS Pro
Joypad button / PS4 Joypad button / X1 Joypad button）to confirm the normal use.
Note: If the Switch enter sleep mode, please perform the following process.
1. Press the power button on the Switch to make the screen light up.
2. Press the Bluetooth pairing button on the N100 Plus , and waiting auto
connection
Ⅲ、Wireless B Mode(Default Mode)
N100 Plus Bluetooth wireless Connection Bluetooth Joypad.The indicator light is green.

PS4 Joypad to connect to Bluetooth pairing:
1. The PS4 Joypad is in the off state.
2. Press and hold the Joypad“ + ”button until the Joypad indicator light flashes
(search for Bluetooth).
3. Connect the N100 Plus to the Switch host according to the diagram. Press the pairing
button and the indicator light flashes double (Search for Bluetooth).
4, wait 3-5 seconds or so, the Joypad indicator light is purple, N100 Plus indicator is
always on, the game display shows that the Joypad is connected successfully and a
"USB" prompt appears, the connection is successful.
X1S Joypad to connect to Bluetooth pairing:
1. The X1S Joypad is in the off state.
2. Press the Joypad“ ”button.
3. Press and hold the Joypad sync button“ ”button until the Joypad indicator
flashes quickly. (search for Bluetooth).
4. Connect the N100 Plus to the Switch host according to the diagram. Press the pairing
button and the indicator light flashes double (Search for Bluetooth).
5. wait 3-5 seconds or so, the Joypad indicator light is always on, the N100 Plus indicator
is always on, the game display shows that the Joypad is connected successfully and a
"USB" prompt appears, the connection is successful.

Pro Joypad to connect to Bluetooth pairing:
1. The NS Pro Joypad is in the normal Bluetooth connection state.
2, enter the Switch host "System Settings" - "Controllers and Sensors" - "Disconnect
Controllers".
3. Press and hold the“Sync Button ”，on the top of the Joypad until the Joypad indicator
flashes cyclically. (Search for Bluetooth)
4. Connect the N100 Plus to the Switch host according to the diagram. Press the pairing
button and the indicator light flashes double (Search for Bluetooth).
5, wait 3-5 seconds or so, the first light of the Joypad indicator light is always on, the game
display shows that the Joypad is connected successfully and a "USB" prompt appears,
the connection is successful.
Ⅳ、Wired Connection
The N100 Plus is wired to the Switch host and Joypad, plug and play. (Only used in
wireless B mode)

Note: When connecting the device, connect the Switch to the last step.
Ⅴ、PC end Joypad use
The N100 Plus has a Bluetooth wireless connection Joypad on the PC side and the
indicator light is green. (Only used in wireless B mode)
Connection, usage, handle Bluetooth pairing and wireless B mode
Ⅵ、COOV assistant PC side
This software could provide the fast and convenient
setting for COOV USB Device, including changing keys, upgrading, recovering, sharing
functions. The users could enter into the official website www.mycoov.come - the COOV
Assistant download page to utilize this software. You could use it by the related statement.

Ⅶ、Firmware/script update
1. Press and hold the N100 Plus pairing button, insert the N100 Plus into the computer's
USB port, and release the N100 Plus disk.
2, use the PC-side COOV assistant to perform online firmware script update
Ⅷ、QuickMacro
Note 1: The same button cannot be activated with the burst function 、the auto combo and
Auto infinite loop function.
Note 2: During the function configuration, each effective operation triggers a handle
vibration.
Note 3: The default operation is to simulate the Capture (NS handle) by double clicking
the HOME button.
A、Button mapping
Button mapping is to map a button to another button, so as to realize the same function of
several buttons or exchange functions of several buttons.
1.Setting
a. Press the PS4 button / X1 button / NS Pro button + PS4 button / X1 button
/ NS Pro button at the same time and release to enter the button mapping function
configuration mode.
b. Press the buttons that need to be mapped
c. Press the mapping button
d. Press the PS4 button / X1 button / NS Pro button to exit the configuration
mode.

For example, press the button first and then press the button, so that the
button has the function of button.
2.Single elimination
a. Press the PS4 button / X1 button / NS Pro button + PS4 button / X1 button
/ NS Pro button at the same time and release to enter the button mapping function
configuration mode.
b. Press the button that needs to eliminate the mapping
c. Press the button that needs to eliminate the mapping again
d. Press the PS4 button / X1 button / NS Pro button to exit the configuration
mode.
For example, press the button first, and then press the button once again, so
that the button will restore the default function.
3.Elimination
a. Press the PS4 button / X1 button / NS Pro button + PS4 button / X1 button
/ NS Pro button at the same time and release to enter the button mapping function
configuration mode.
b. Hold down the PS4 button / X1 button / NS Pro button for 3 seconds, all the
configured button mappings will be eliminated automatically, and it will exit the
configuration mode automatically.
4.Examples1
a. First map the button to , and then map the button to , so that the two
buttons can exchange function.
(In the button mapping mode, the operation is to press , , , )
b. Map the button to , map to , and then map to , so that the
three buttons can exchange function; and so forth
(In the button mapping mode, the operation is to press , , , , , )

5.Examples 2(exchange touchpad and SHARE)
a. In this configuration process, double-click PS4 button / X1 button / NS
Pro button can not be simulated into other keys, so you need ps4 handle or pro handle
for this operation
b. Enter key mapping function configuration mode, press the （PS4 button /
X1 button / NS Pro button）/（PS4 button / NS Pro button）/
（PS4 button / NS Pro button）/（PS4 button / X1 button / NS
Pro button）, then press PS4 button / X1 button / NS Pro button to exit
6.Button supported
All buttons except the PS4 button / X1 button / NS Pro button and the rocker
B、Burst (off by default)
Burst control is used to configure the selected button to a burst mode. When the button is
in a burst mode, once it is pressed, it will simulate the pressing-releasing event at a
certain frequency, and the frequency is adjustable.
1.Turn on the burst
a. Press the PS4 button / X1 button / NS Pro button + PS4 button / X1 button
/ NS Pro button at the same time and release to enter the burst function configuration
mode.
b. Hold down the button that needs to turn on the burst function, and then press the
PS4 button / X1 button / NS Pro button, so that the burst function of the
corresponding button can be turned on.
c. Press the PS4 button / X1 button / NS Pro button to exit the configuration mode.
2.Turn on the burst
a. Press the PS4 button / X1 button / NS Pro button + PS4 button / X1 button
/ NS Pro button at the same time and release to enter the burst function configuration
mode.

b. Hold down the button that needs to turn off the burst function, and then press the
PS4 button / X1 button / NS Pro button, so that the burst function of the
corresponding button can be turned off.
c. Press the PS4 button / X1 button / NS Pro button to exit the configuration mode.
3.Elimination of all the burst
a. Press the PS4 button / X1 button / NS Pro button + PS4 button / X1 button
/ NS Pro button at the same time and release to enter the burst function configuration
mode.
b. Hold down the PS4 button / X1 button / NS Pro button for 3 seconds, all the
configured burst function will be eliminated automatically, and it will exit the configuration
mode automatically.
4.Adjust the burst frequency(Basic mode)
a. Press the PS4 button / X1 button / NS Pro button + PS4 button / X1 button
/ NS Pro button at the same time and release to enter the burst function configuration
mode.
b. Press the to Increase the burst frequency
c. Press the to reduce the burst frequency
d. Press the PS4 button / X1 button / NS Pro button to exit the configuration
mode.
5.Adjust the burst frequency(Custom mode)
In custom mode, the user can set two parameters: press time a millisecond and release
time b milliseconds. When the burst starts, the key is automatically pressed for a
millisecond, then released for b milliseconds, and then pressed a millisecond for a round
trip. The values of a and b should be greater than 4 and less than 252.
a. Determine the value you want to set, such as a is 128, b is 164
b. Press the PS4 button / X1 button / NS Pro button + PS4 button /
X1 button / NS Pro button at the same time left and release, enter the serial
configuration mode