coov N200 Parts list manual

COOV N200 功能秘籍
Function Instruction of COOV N200
以X1，PS4 手柄按键分布图为例：
Take the button distribution of X1 and PS4 handle an example:
中左
Middle left button
十字键上
Up of cross button
十字键下
Down of cross button

上键
Up button
左键
Left button
右键
Right button
下键
Down button
中右
Middle right button
N200 无线连接示意图：
N200 wireless connection diagram:

电源按钮
Power button
COOV N200T 三视图及接口说明
Three-view drawing and interface description of COOV N200T
电源按钮
Power button
靠近按钮的接口为“接口 A”
The interface close to the button is "Interface A"
远离按钮的接口为“接口 B”
The interface away from the button is "Interface B"
不连接“接口 A”
Do not connect "Interface A"
连接“接口 B”
Connect "Interface B"
无线连接

Wireless connection
OTG 线
OTG line
无线连接 Switch
Wireless Connection Switch
1. 将官方配送的魔术贴贴至手柄背面

1. Stick the Velcro in the set to the back of the handle
2.将N200T 带有魔术贴的面粘贴至手柄背面魔术贴处
2. Paste the Velcro side of the N200T to the Velcro on the back of the handle.
N200T 与手柄完美融入一体
N200T and handle are integrated into one perfectly.
无线连接
Wireless connection
N200S 插入 Switch
Insert N200S to the Switch
连接设备（如连接示意图所示）
Connect equipment (as shown in the connection diagram)
A：将 N200S 通过 TYPE-C OTG 线或者 USB 接口连接至 Switch。
A: Connect the N200S to the Switch through the TYPE-C OTG line or the USB
interface.
B：将 N200T 的“接口 B”通过配套专线连接至手柄，并用魔术贴贴至手柄背面。
B: connect the "Interface B" of N200T to the handle through a matching line and
stick it to the back of the handle with a Velcro.
C: 按N200T 背部的电源键即可启动使用产品。
C: Press the power button at the back of the N200T to start the product.
PS: 1、靠近 N200T 的“接口 A”为充电接口。

PS: 1. The "Interface A" close to N200T is the charging interface.
2、N200T 长按一秒开、关机。断开连接 5分钟后自动关机。手柄闲置不动 15 分
钟后自动关机。
2. Press the power button for one second to turn on or turn off N200T. It will turn
off automatically after disconnecting for 5 minutes. It will turn off automatically
after leaving unused for 15 minutes.
3、N200T 低电量状态闪烁红灯，满电状态闪烁绿灯（部分批次为蓝灯），其他状
态闪烁白灯。
3. In the low power state, the red light flickers; in the full power state, the green
light (blue light in some batches) flickers green light; the white light flickers in
other states.
N200 有线连接示意图：
N200 wired connection diagram:

连接“接口 A”
Connect Switch to "Interface A"
配套专用线“接口 B”
Connect the matching special line of N200 to "Interface B"
手柄数据线
Handle data wire

OTG 线
OTG line
连接设备（如连接示意图所示）
Connect equipment (as shown in the connection diagram)
A：将 N200T 的”接口 B”通过配套专线连接至手柄，并用魔术贴贴至手柄背面。
A: Connect the "Interface B" of N200T to the handle through a matching line and
stick it to the back of the handle with a magic Velcro.
B：将 N200T 的“接口 A”通过 TYPE-C OTG 线与手柄数据线连接至 Switch。
B: Connect the "Interface A" of N200T to the Switch through the TYPE-C OTG line
with the handle data line.
C: 按N200T 背部的电源键即可启动使用产品。
C: Press the power button at the back of the N200T to start the product.
PS: 有线连接不需要使用到 N200S，且带有体感功能。
PS: The wired connection does not need the N200S and has a somatosensory
function.
设备升级：
Equipment upgrade:

A: N200T 升级
A: N200T upgrade
将MICRO USB 线一端连入 N200T 的“接口 A”，另外一端连接电脑 USB 口。 将
N200T 的升级文件 firmware.bin 文件文件复制到 N200T 磁盘。
Connect one end of the MICRO USB wire to the "Interface A" of N200T, and the
other end to the USB port of the computer. Copy the upgrade file of firmware.bin
of the N200T to the N200T disk.
B：N200S 升级
B:N200S upgrade
在N200T 关机状态下，将 N200S 连接电脑 USB 口，将 N200S 的升级文件
firmware.bin 文件复制到 N200S 磁盘。
In the shutdown state of N200T, connect the N200S to the USB port of the
computer, and copy the upgrade file of firmware.bin of the N200S to the N200S
disk.
注：1、win8 企业版 和win10 企业版 用户有可能不支持 N200s 的插入
Note:
1. Some users of the win8 enterprise version and win10 enterprise version may not
support the insertion of N200s.
2、升级固件的顺序可随意（可以先升级 N200S 也可以先升级 N200T）

2. The order of the firmware upgrade is optional (you can upgrade N200S
first, or upgrade N200T first)
3、N200T 和N200S 插入电脑后识别较慢，请用户耐心等待
3. N200T and N200S are slow to be recognized after they are inserted into the
computer. Please wait patiently.
无线使用场景：
Wireless usage scenario
出厂状态下的 N200 已进行过无线配对，N200T 的电池也具有一定电量。用户只需将
N200S 连接主机，将 N200T 连接手柄，再按下 N200T 背部的电源键即可启动。无线使
用场景下的软件功能与 N100 相同。
N200 has been wirelessly paired in the factory state, and the N200T battery has a
certain amount of electricity. The user only needs to connect the N200S to the
host, the N200T to the handle, and then press the power key on the back of the
N200T to start. The software function in the wireless usage scenario is the same as
that of N100.
如何开关机：
How to turn on/off the machine: