COP-USA CD250XIR-WDR User manual

CD250XIR‐WDR
User'sManual
DOWNUPLEFTRIGHTENTER
Thesebuttonsarelocatedinsidethedomeonthe
backoftheCCDBoard.
PressthecenterButton toEntertheOSDMenu.
MoveUporDowntomovethruthemenuoptionsandleftorrightto
changevaluesonthemenu,
Pressthecenterbuttonagaintogetintosubmenus.
Alwaysremembertosavebeforeyouexit.
WhenyouHighlighttheReturnOption,presstherightbuttontoeitherexit,
saveandexitorjustreturn.
MENU
EXPOSURE
COLOR
DAY &NIGHT
EFFECT
MOTION
PRIVACY
ENHANCE
SYSTEM
Packing List:
‐1ArlenScrewdriver
‐1miniflatscrewdrive
‐1kitwithscrewsandanchors
‐1SpecificationSheet
‐1miniflatscrewdrive
‐1DCconnector

1.EXPOSURE
EXPOSUREMENU NORMAL
/
BLC
/
WDR
/
HLI
SENSEUP OFF
/
X2~X1024
AGC OFF
/
LOW
/
MIDDLE
/
HIGH
LENS ELECTR
/
DCIRIS
BRIGHTNESS 0~99
EXIT
ExposureSettings:
Normal
Tobeusedundernormallight
conditions,wherenoneofthe
conditionslistedbelowarepresent
.
BLC(BacklightCompensation)
WDR (WideDynamicRange)
ThisFunctionisusedto
Senseup:(Slowshutter Speed)
OFF
X2~X1024Manual Slowshutter
modeselectfromlowx2uptohigh
x1024
AGC :(IncreasesBrightness,the
higherthesettingthemorenoise
willgetonthevideo)
Lens:
ELECTR.(youmustusethisoption
asdefaultsetting)
GotoSubmenuandselectthe
speedfortheShutter.
‐1/100000to1/60FLC
‐AUTO
‐X2toX1024
DCIRIS
1/100000 1/60FLC
Brightness:
Brightnesscontrol
itrangesfrom0~99
2.COLOR
WBMODE ATW
/
AWC
/
MANUAL
/
PUSH
EXIT
compensatethestrongBacklight
conditions.
HLI (HighLevelInterface)
ThisFunctionisusedwhenreading
Licenseplateatnight.
ATW(AutoTrackingWhiteBalance)
ItAutomaticallyadjuststhecolorbetween
1.800Kand10500K.
Usethisoptionifthelightingconditions
changesconstantly
MANUAL(Adjustthecolormanually)
AdjusttheREDandBLUEsettingswithvalues
rangingfrom0~255
OFFAGCdisabled
LOWLow AGCSetting
MIDDLEMiddleAGCSetting
HIGHHighAGCSetting
‐
1/100000
to
1/60FLC

‐AUTO
‐X2toX1024
AWC(PresetWhiteBalance)
Usethisoptionwhenmanywhiteobjects
appearsonthesceneandalsowhenaobject
mergestothescenewithsimilarcolorshade
PUSH
Adjustthewhitebalancebyfocusingata
whiteobjectorwhitesheetofpaperandpres
sentertoadjustthecolor.

2.DAY&NIGHT
MODE SMARTLED
/
NIGHT
/
DAY
/
AUTO
BURST ON
/
OFF
DAY
/
NIGHT 0~255
NIGHT
/
DAY 0~255
DELAYTIME 0~10
CDS_START 0~255
CDS_END 0~255
EXIT
MODE:
SMARTLED
AdjuststheIRlevelandalsoadjustthebrightness
dependingonthedistanceoftheobject
NIGHT
StaysonNightmodeandB/W
DAY
BURST:
ON
Whenthisisselected,aCOLOR‐ B/Wpicturewillbe
shown.Thiswillincreasethenoise.
OFF
WhenthisisSelectedatrueB/Wpiocturewillbe
CDS:
CDS_START
This O
p
tionsetstheCDSSensorlevelwhichwilldeterminewhen
DELAY TIME:
This FunctioncontrolstheswitchingtimebetweenDAYmodeto
NIGHTmode,andFromNIGHTmodetoDAYmode.
3.EFFECT
FREEZE
MIRROR HORI
/
VERT
/
ROTATE
D.ZOOM ON
/
OFF
(
X1.0~X10.0
)
SHARPNESS SHARPNESS
(
0~49
)
STABILIZER
EXIT
StaysonDAYmodeandColor
AUTO
CameraswitchesfromColortoB/Wdependingon
theilluminationofthescene.
DAY/NIGHT
This Optionsetsthebrightnesslevelwhichwill
determinewhentoswitchfromDAYtoNIGHTmode.
NIGHT/DAY
This Optionsetsthebrightnesslevelwhichwill
determinewhentoswitchfromNIGHTtoDAYmode.
p
toswitchfromDAYtoNIGHTmode.AndtoturntheIRCutON
CDS_END
This OptionsetstheCDSlevelwhichwilldeterminewhento
switchfromNIGHTtoDAYmode.AndtoturntheIRCutOFF.
MIRROR
This Optionallowsyoutomirrortheimagehorizontally,verticallyandRotate(turnstheimageUpside
down.
D.ZOOM
ThisFunctionallowstomagnifyaimageupto10Xdigital.
SHARPNESS
AdjusttheImageSharpnessdecreasingorIncreasingtheValues
STABILIZER
Thisfunctionhelpstostabilizethepictureandreducethe
imageshakewhenthecameraphysicallymoves.This
functionisusefulespeciallywhenusingahigh‐zoomlens,
whereeverysmallmovementofthecameraresultsinshake

4.MOTION
MOTIONDET. ON
/
OFF
ALARMMODE OFF
/
MESSAGE
/
AREA
SENSITIVITY 0~120
AREASELECT 1~4
MODE
ON/OFF
START
X

(0
~
15)

/

Y(0
~
15)
END
X

(0
~
16)

/

Y(0
~
16)
OUTPUT

TIME
0
~
10
AUTO

ZOOM
ON/OFF

(N/A)
EXIT
MOTIONDET.(ON/OFF)
ThisFunctionallowstoidentifytheareawherethemotionisdetected
ALARM MODE :
OFF‐ WillnotnotifywhenMotionisDetected
MESSAGE‐ WillShowamaninmotioniconontopofthescreen.
ld ill hidi i iii
AREA SELECT.1~4
Thisfunctionenablesupto4motionareas.
MODE ON/OFF
EnableandDisabletheMOTIONAREA.
STARTX(0~15)/ENDX(0~16)
DrawstheHorizontalMotionArea
STARTY((0~14)/ENDY(0~15)
Draws the Vertical Motion Area
4.PRIVACY
MASKSELECT 1~8
MODE ON
/
OFF
COLOR 1~7
TOP X
(
29~216
)

/
y
(
5~128
)
LEFT
X

(29
~
216)

/
y
(5
~
128)
RIGHT
X

(29
~
216)

/
y
(5
~
128)
BOTTOM
X

(29
~
216)

/
y
(5
~
128)
MOVE
X

(29
~
216)

/
y
(5
~
128)
EXIT
AREA ‐Aco
l
ore
d
transparentAreaw
ill
s
h
owup
i
n
di
cat
i
ngmot
i
onact
i
v
i
ty.
SENSITIVITY
SetstheMotionSensitivitylevels.from0(low)to120(High).
Draws

the

Vertical

Motion

Area
*togettoYsettings,highlighttheXoptionandpressENTER.
OUTPUTTIME
Rangefrom0~10seconds.FortheALARMMessageModeONLY.
AUTOZOOMN/A
READTIME(3~12)N/A
ZOOMIN(1~44)N/A

4.ENHANCE
GAMMA 0.3~1.0
3D‐DNR 0~5
MONITOR CRT
/
LCD
DPC
OFF/AUTO
MASKSELECT
Thiscamerahasupto8maskingareas.These8MaskingAreascanbesetupanywhereinthescreen.
andeachmaskcanbeenabledordisabledanytime.
MODE(ON/OFF)
EnablesorDisablesthePrivacyMasks.Makesureyouareselectingtherightprivacymask,lookingattheMASKSELECTnumber.
COLOR
youcanchoosefrom7differentmaskcolors.
TOP/LEFT/RIGHT/BOTTOM/MOVE
UsethesecommandstoadjustthesizeoftheMaskandLocationbylookingatthedrawing,youwillseewhichisTOP/RIGHT/BOTTOMandLEFT.
Xistomoveoneofthearea'spointHorizontally.
Yistomoveoneofthearea'spointVertically.
MOVEXmovetheMaskAreahorizontally
DPC OFF
/
AUTO
LENS

CORR
.
0
~
50
EXIT
Usethesefeaturestoenhancethequalityofthevideo
Gamma‐ (AdjusttheBrightness0.3brighter1.0darker)
3D‐DNR‐(ThisFeatureistoreducetheBackgroundnoiseinalowlightenvironment.)
Monitor‐(ChoosethemonitorTypeused)
DPC‐(N/A)
LENSCORR.‐HelpsenhancethebrightnessatthecornersofthescreenValuesrangefrom0to5fromdarktobright.

5.SYSTEM
COMMID. N/A
RS‐485 N/A
BAUDRATE N/A
TITLE ON/OFF TITLE EDIT
LANGUAGE ENGLISH/CHINESE LOCATION
RETURN
SYNC INTER/AUTO AUTO V‐PHASE
RETURN
EXIT
TITLE:
EDIT: (editthecameratitleusing
thesecharactersmovearound
usingthedirectionalbuttonsand
pressthecenterbuttontoselect).
/
TITLE:
LOCATION: (usethedirectional
buttonstomovethetitle
location)
RETURN
@#*+_
/
(=)
1234567890
OWERTYUIOP
ASDFGHJKL:
ZXCVBNM,.?
_____________
RETURN
CLEAR