Coram Showers OPTIMA QUADRANT User manual

71799 00 / Issue 1 / 15
CUSTOMER CARELINE 01746 713410
Equipment needed:
Drill, 6.5mm Masonry Bit, 4.5mm & 3mm Metal Bits (general), Crosshead Screwdriver, 16mm Spanner, Spirit Level, Pencil,
Tape Measure, Masking Tape, Silicone Sealant.
Note: The screws and wall plugs supplied are for masonry walls. For lightweight walls i.e. stud partition, plasterboard etc,
use the correct type of fixings.
OPTIMA QUADRANT / OFFSET
QUADRANT
X X
Y
Z
Please read these instructions carefully and keep for future reference.
Incorrect fitting will invalidate the guarantee.
SAFETY
● Handle glass with great care. Although the glass is very tough, sharp impacts can damage both the glass and metal frame.
● Make sure there are no hidden pipes or cables hidden in the wall where you intend to drill.
● Wear safety goggles, shoes and appropriate clothing.
BEFORE INSTALLATION
● Check that the shower tray is level in all directions. The enclosure will not sit correctly on an uneven surface.
If uneven, the wall channels may not fit and the doors may not shut correctly.
● The enclosure should be fitted on tiled walls which are sealed with waterproof grout.
●There must be a good silicone seal between the rim of the shower tray and the wall.
● The shower tray and the enclosure must match in size. Attempting to fit the incorrect size of enclosure to
the shower tray will result in water leaks.
● Always check very carefully that components are vertical.
Y= Widths:
1000 x 800 Door = 780 - 805mm
1200 x 800 Door = 780 - 805mm
1200 x 900 Door = 880 - 905mm
DIMENSIONS
Check the enclosure size in the table below matches the showertray installation.
Z = Widths:
1000 x 800 Door = 980 - 1005mm
1200 x 800 Door = 1180 - 1205mm
1200 x 900 Door = 1180 - 1205mm
X = Widths:
800 Door X = 780 - 805mm
900 Door X = 880 - 905mm

2
100mm
max
=
=
=
100mm
max
ø 4.5
mm
a: Drill holes in both wall channels at points shown using a 4.5mm drill bit, where shown.
b: Ensure the shower tray is level in all directions.
IMPORTANT: Clean the tray and seal the gap between the tray surface and tiles. It is important that the tray is sealed right up to
the tray edge so that the bottom of the wall channel is sealed. Failure to do this will cause water to leak under the wall channel
and between the tray and tiles, resulting in damp patches on the wall and under the tray.
1a b
PN10801
800 RAIL - PN80684
900 RAIL - PN80685
PN10801
800 RAIL - PN80684
900 RAIL - PN80685
PN10801
PN10801
1000 x 800 RAIL - PN80686
1200 x 800 RAIL - PN80687
1200 x 900 RAIL - PN80688
1000 x 800 RAIL - PN80689
1200 x 800 RAIL - PN80690
1200 x 900 RAIL - PN80691
Check contents of pack before installation. If anything is missing, contact our Customer Careline for assistance.
CUSTOMER CARELINE: 01746 713410
8
PN3230
8
PN3225
2
8/4
10 2
Inner &
Outer
wheel
covers
PN40335
32mm
4
4
2
PN50490
PN50488
14
PN4748
PN60510 PN40350
PN80564
1/1
PN50493
PN50494 1/1
PN60524
10mm
800 x 800
900 x 900
1000 x 800
1200 x 800
1200 x 900
= PN40338
= PN40340
= PN40344
+ PN40338
= PN40349
+ PN40388
= PN40349
+ PN40340
4
4
2
2
2
2
2
2
Short
seal
Long
seal

3
3
a: Place the wall channels on the tray ensuring they are vertical and an equal distance back from the front of the tray.
Place masking tape against the wall before marking drill hole positions, this will help prevent the drill bit slipping. Drill 6.5mm
holes, 30mm deep and insert the wall plugs.
b: Apply sealant to the back of the wall channels. c: Fix the wall channels to the walls using 8 x 32mm screws and screw caps.
Inside
32mm
a b c
2
The Offset Quadrant can be assembled with the offset on either the right
or left. Note: The following instructions show installation of the Quadrant.
a: Place the bottom rail onto the tray with its end mouldings inserted into the wall channels.
b: Centre the bottom rail between the wall channels so that there is an equal gap at each end.
4a b
==
X
ø 6.5
mm
X = Door widths
800 = 780 - 805mm
900 = 880 - 905mm
X
Y = Widths
1000 x 800 = 780 - 805mm
1200 x 800 = 780 - 805mm
1200 x 900 = 880 - 905mm
X = Widths
1000 x 800 = 980 - 1005mm
1200 x 800 = 1180 - 1205mm
1200 x 900 = 1180 - 1205mm
XY

5
Push fit the 'flipper seals' onto the top and bottom
edges of both fixed panels - flush against the metal
profile. Ensure the flipper seal 'flaps' are on the
inside of the fixed panels.
Note: Wetting the glass with water will help fit the seals.
6
Position the fixed panels into the wall channels and slide down so
that they fully slot onto the end mouldings of the bottom rail.
4
Outside
face of fixed
panels
Out-
side
face of
fixed
panel
7
Position the top rail onto the top of
the fixed panels/wall channels.
Ensure the top rail is fully pushed
down.
Out-
side
face of
fixed
panel

5
8
Check the door frame is vertical and is centrally positioned between the wall channels.
From inside the enclosure, in the 6 positions shown, drill through the wall channels into the fixed panels.
Important: The top holes MUST be 18mm down from the top. Drill using a 3mm drill bit.
Fix using 6 x 10mm screws and screw caps.
From inside
10mm
9
a: Attach 2 x glass clamps to each of the horizontal rails (at edge of glass) using 10mm screws, tighten by hand only - do not
overtighten. Push fit glass clamp covers.
b: Select the short vertical seals (PN40350), fit the seals to both fixed panels.
Important: Seals must sit tight against glass clamps (top and bottom).
Important: Seal 'flippers' must be on inside of the enclosure. Note: Wetting the glass with water will help fit the seals.
Inside of
fixed panel
PN50490
ø 3
mm
18mm
PN50488
10mm
Inside of
fixed panel
a b
PN40350
<ID

11
a: Select the long vertical seals (PN40335), fit the seals onto the back edge of the
doors. Ensure the flipper seal 'flaps' are on the outside of the doors.
b: Push fit 'magnetic seals' (PN80564) onto the closing edge of the doors (the same
side as door handle).
Note: Ensure the magnetic seals are positioned as shown.
Note: Wetting the glass with water will help fit the seals.
PN40335
PN80564
PN80564
Outside
a
Outside
face of
door
Outside
face of
door
PN80564
PN40335
10
Fit the door handles (PN60510) to the
door ensuring the washers fit between
the glass and handle.
b
a: From inside the enclosure, position the top wheels into the top rail. b: From outside the enclosure with the door closed,
push down the 'plungers' on both bottom wheels, position into the bottom rail and release. Repeat with other door.
12
From inside
Top of doors
Bottom of doors
6
Inside
Outside
From
inside
From
outside
a
b

7
Door adjustment: The wheels at the top of the doors may need adjusting so that the doors slide freely and the magnetic seals
meet evenly when the doors are closed.
a: From outside the enclosure and with the doors closed, adjust the screws on the top wheels. The bottom wheels should be
securely located in the bottom rail but the door must not be raised so high that the 'plungers' on the bottom wheels do not
operate.
b: The 'plungers' on the bottom wheels can be pushed down to unclip the doors which will allow access to clean the doors and
fixed panels.
13
From inside
a
b
Adjust
from
outside
Magnetic
seals
14
a: From outside the enclosure push fit the outer wheel covers onto the wheels at the top of the doors.
b: From inside the enclosure push fit the inner wheel covers onto the wheels at the top and bottom of the doors.
a b
From inside
- top and bottom
From
outside
- top only

16
From the outside only, apply sealant to the bottom of the enclosure and 50mm up the wall channels and vertical joints as shown.
15
Push fit the top caps (PN50493/50494) onto the wall channels.
50mm
CORAM SHOWERS LTD
Stanmore Industrial Estate, Bridgnorth, Shropshire WV15 5HP, UK •Tel: [phone] •Fax: [phone] • www.coram.co.uk
Recycling
Packaging:- The cardboard and polythene parts of this packaging can be recycled.
End of life:- This product contains materials such as aluminium and glass which can be recycled.
Please contact your local authority to find your nearest recycling centre.
IMPORTANT: You must not use the shower for 24 hours after installation of the enclosure.
DO NOT use bleach, scouring powders, solvents or other aggressive cleaning agents. To clean, use warm soapy water and a
clean cloth and rinse off.
Please note: There has been a glass coating applied to this product, use a squeegee to remove water and debris.
Periodically check all fixings and tighten if necessary.
Li Li

Check out our full range of Shower Enclosures
Quadrant Shower Enclosures
Corner Entry Shower Enclosures
Walk in Shower Enclosures
Sliding Shower Doors
Bifold Shower Doors
Pivot Shower Doors
Hinged Shower Doors
Shower Screens
From Top Brands
Coram Shower Enclosures
Mira Shower Enclosures
Hydrolux Shower Enclosures
Diamond Shower Enclosures
With quality shower trays to match your enclosure
Square Shower Trays
Rectangular Shower Trays
Quadrant Shower Trays
Coram Shower Trays
Mira Flight Shower Trays