Core Products HR915 User manual

Height: 700 mm
Width: 1017 mm
Depth: 390 mm
95 min
PLEASE RETAIN THIS INSTRUCTION LEAFLET FOR FUTURE REFERENCE.
SMALL SIDEBOARD
WITH 2 DOORS & 1 DRAWER
BEFORE YOU START ASSEMBLY
Please check that you have all the
correct parts and fittings as detailed.
We recommend that you build your
furniture on top of a soft clean cover to
ensure the unit does not get marked or
damaged during assembly.
Thank you for choosing this furniture.
BEFORE YOU START ASSEMBLY please store the carton for 48 hours or more so the contents can acclimatise.
PLEASE RETAIN ALL PACKING UNTIL YOU HAVE COMPLETED ASSEMBLY.
Information about your furniture.
This furniture range has been carefully crafted from melamine faced manufactured board.
Each piece is manufactured to the highest standards using specialised computer controlled machinery to ensure accuracy.
Caring for your furniture.
Extreme temperature can cause slight movements in the board material so please avoid placing your furniture close to radiators or other direct sources of heat.
Please avoid exposing your furniture to continued bright sunlight as this can affect the colour.
Any fluid spills should be removed as quickly as possible.
Always lift your furniture when moving as dragging may cause damage to your furniture or flooring.
Always use place mats, coasters or tablecloths to help protect against scratches and accidentally dropped items. Always use heat resistant mats when placing hot or
cold items on to surfaces.
Do not sit or stand on your furniture.
After care.
Wipe all surfaces with a dry cloth and the occasional use of a normal household furniture polish and a household glass cleaner on glass surfaces.
Please do not use detergents or chemicals on your furniture.
After assembly remove all visible component identification stickers, these should remove easily however any remaining adhesive residue can be easily removed with
a label adhesive removal liquid available from most DIY or hardware stores.
02/10/2020

x40
Dowel Minifix Bolt
x30
Cover Caps
x30
Colour 1
x30
Minifix Cams
x1
Roll Over Kit
(Includes screws)
x1
Drawer Slides
(Includes screws)
Page 2
ASSEMBLY PARTS MAX SUGGESTED LOADS
A - x1
B - x1
C - x1
D - x1
E - x1
F - x4
G - x2
H - x1
I - x1
J - x1
K - x1
L - x1
M - x1
N - x1
O - x4
8kg
End Panel
Hinge (EPH)
(Includes screws)
x4 x4
Screw
(50,8mm)
10kg
5kg
15kg
8kg
Handle
(Includes screws)
x3
Leg
x4
Screw
(28,5mm)
x8
ASSEMBLY HARDWARE
O
O
O
O
B
C
D
E
F
F
F
F
H
G
G
I
L
K
J
M
N
A

1
2
3
Page 3
Fx4
Front
B
B
F
F
12
Gently hit to adjust.
Repeat this in the
following steps.
Gently hit to adjust.
Repeat this in the
following steps.
Gently hit to adjust.
Repeat this in the
following steps.
2
1
Rotate 180°
End Panel Hinge (EPH)
413

Page 4
4
5
6
Gx2
G
F
F
B
Rotate to tighten
Gently hit
to adjust.
D
Front
4
13

7
8
9
Page 5
Rotate
D
D
G F
F
B
Rotate to tighten
C
End Panel Hinge (EPH)
Gently hit
to adjust.

10
11
12
Page 6
Rotate to tighten F
F
C
F
F
C
G
F
F
F
F
G
G
D B
C
Rotate to tighten
Gently hit
to adjust.
Gently hit
to adjust.
Gently hit
to adjust.
Rotate to tighten

13
14
15
Page 7
E
E
F
F
F
F
D B
C G
G
Rotate to tighten
B
D
B
E
F
F
F
F G
O
O O
O
Gently hit
to adjust.
Slide the back panels
inside the cabinet

16
17
18
Page 8
A
Rotate to tighten
Gently hit
to adjust.
A B
G
G
O
B
F
F
F
F O O
O
28,5mm
A B
O
F
F
F
F O O
O

19
Page 9
20
1
5
4
3
2
E
H
I
C
A
G G
B O
D
J
K
Depth adjustment
Hinge adjustment
Side adjustment Height adjustment Secure Hinge

21
Page 10
22
23
L
K
J
Screw
(50,8mm)
N
J
1
2
N
J
K
M

25
24
Page 11
Rotate to tighten
N
MJ
L
K
-WARNING! TIPPING HAZARD – Unanchored
furniture can tip over
-WARNING: CHECK FOR HIDDEN PIPES AND
CABLES BEFORE DRILLING.
-IMPORTANT: IF YOUR WALLS ARE NOT SOLID
LIKE BRICK OR STONE, YOU WILL REQUIRE
SPECIALIST FITTINGS (NOT SUPPLIED)
-Pre-drill small pilot hole on the back edge of the
furniture top using a 2mm drill bit. Attach the other
end of the fixing strip to the back edge of the
furniture top using the 15mm screw + washer and
securely tighten.
-Place fixing strip against the wall and mark position
for drilling hole.
-Drill hole in your wall to a depth of 30mm using a
6mm drill bit. If the surface of your wall is soft and
crumbly, we would advise you to use a 5mm drill bit
for a tighter fit.
-Insert plug into hole with end flush to the wall
surface.
-Attach fixing strip to the wall using the 25mm
screw + washer and securely tighten.
Slide the drawer
inside the cabinet.
M
HIC
E
After you finish the
adjustment of the cams,
cover them with the
cover caps. AAfter you finish
assembling the cabinet,
take off the adhesive
letters.