Cornelius IDC Pro Guide

Berkshire Hathaway
SSD Replacement Instructions – IDC PRO
Before replacing SSD, if unit is operational or you have a second IDC PRO unit with
an identical brand lineup be sure to get a back up copy of the units configuration
onto a USB memory stick (see troubleshooting pages 15-19 “Exporting brand
configuration from a pre-existing machine”) and or write down the units flavor line
up on the provided Flavor Line Up sheet. This will speed up the process when you
are reconfiguring the unit after new SSD is put into screen.
Document Revision x2
1
IMPORTANT

IDC Pro Flavor Line Up
•Up to 10 brands per multi-flavor valve
•Up to 4 flavor shots per multi-flavor valve
•One plain water per valve, with optional flavor shots
•One carbonated water per valve
•One flavor shot pour per valve
Dispenser serial number -___________________
Left Side Right side
S1 ___________________ S8 _________________
S2 ___________________ S9 _________________
S3 ___________________ S10 _________________
S4 ___________________ S11 _________________
S5 ___________________ S12 _________________
S6 ___________________ S13 _________________
S7 ___________________ S14 _________________
A1 ___________________ A4 _________________
A2 ___________________ A5 _________________
A3 ___________________ A6 _________________
Flavor Shots
F1 ________________ F5 _______________
F2 ________________ F6 _______________
F3 ________________ F7 _______________
F4 ________________ F8 _______________
*S1-S14 will run through the cold plate and will be used for your carbonated
brands.
*A1-A6 is your ambient lines and will be used for your non-carbonated brands. If
you have more than 7 carbonated brands you can run carbonated brands through
the ambient lines but you want to use a low volume and low foaming brand.

Berkshire Hathaway
SSD Replacement Instructions – IDC PRO
Tools Required:
1. Large Phillips Screw Driver
2. Fine Tip Phillips Screw Driver
3. USB Memory stick
Document Revision x2
Replacement Operation:
1. Locate the SBC Cover
on the back side of the door
2. Remove the 4 screws as shown
3. Carefully hold the cover until
the fan harness is disconnected
Before proceeding, unplug
the power harness from the unit.
NOTES:
1. Wear a properly grounded ESD wrist strap
if available.
2. Minimize body contact with electronic
components.
2

Berkshire Hathaway
SSD Replacement Instructions – IDC PRO
Document Revision x2
4. Disconnect the fan harness and remove the cover
3

Berkshire Hathaway
SSD Replacement Instructions – IDC PRO
Document Revision x2
5. Carefully undo the lock screw to unlock the SSD. DO NOT LOOSE THIS PART!
4

Berkshire Hathaway
SSD Replacement Instructions – IDC PRO
Document Revision x2
6. Carefully replace the SSD with a new part
5

Berkshire Hathaway
SSD Replacement Instructions – IDC PRO
Document Revision x2
7. Carefully secure the lock screw to lock the SSD. DO NOT LOOSE THIS PART!
6

Berkshire Hathaway
SSD Replacement Instructions – IDC PRO
Document Revision x2
8. Connect the fan harness and replace the cover. Make sure the silicone
(white glue) doesn’t get in the way of the pins and connector.
7

Berkshire Hathaway
SSD Replacement Instructions – IDC PRO
Document Revision x2
9. Close the SBC cover
10. Secure the 4 screws as shown
11. Reconnect the power harness
12. After power up, ensure the fan
is working properly.
8

Berkshire Hathaway
Troubleshooting
Screen resolution comes up incorrect
Document Revision x2
1. If image on the screen appears to be
too far zoomed in or out the screen
resolution will need to be adjusted
in the Bios settings.
2. Plug in a keyboard into a USB port
on the back of the screen. Restart
the unit and during the initial
startup “AAEON” screen continually
press the DELETE key.
9