Cosmo S9 6 Operation manual
RANGETOP INSTALLATION & CARE
USER MANUAL
1
Important Safety Instructions
6 burners
BA
C
D
D
D
071
065
065 065
065
092
092
092 11
062
062
062
062 062
Position: 065 (Outer A Top Left, Outer A Top Right, Outer A Bottom Left, Outer A Bottom Right)
Position: 062 (Outer B Top Left, Outer B Top Right, Lower B Bottom Left, Lower B Bottom Right ), Inner B Middle
Position: 092 (Inner D Middle)
Position: 071 (Inner A Middle)
Position: 11 (Inner C Middle)
Natural Gas Conversion/Replacement Kit
18
Each nozzle is lightly engraved and numbered. You may view the engraving by putting a light on the side of the
nozzle. There are only 5 types of nozzles identified by their numbers (065,062,092,071,11). Each nozzle must be
inserted into the correct department. This must be done by a technician or all warranties are void.
1. Please ensure a white threaded sealant is used to avoid leakage around the threading of the nozzle prior to
insertion. This is mandatory.
2. Please shut all gas off to the appliance prior to configuration.
3. Please tighten each nozzle by hand until you can't turn any longer. Please then use a socket wrench and ONLY
turn one quarter turn clockwise. Any additional turning performed by the socket wrench can break the nozzle
compartment and destroy the burner assembly.
4. Please supply power to the gas and check for gas leaks by spraying the nozzles with a gas leak formula. If
bubbles are noticed and are expanding around the nozzle compartment, please shut off power to your gas supply
again and repeat steps 1-3 until no gas leaks are noticed.
IMPORTANT-PLEASEREADANDFOLLOW
üBefore usingthisappliance please readthese instructionscarefully.
üDonotremove permanentlyaffixedlabels.warnings, orplatesfromthe product.Thismayinvalidate the
warranty.
üPlease observe all localandnationalcodesandordinanceswithregardtothe installation ofa gashob.
üPlease ensure thatthisproductisproperlygrounded.
üTheinstallershouldleave these Instructionswiththe consumerwhoshouldretainforlocalInspector's
use and forfuturereference.
üThe electricalplug shouldalwaysbe accessible.
Installation ofany gas-firedequipmentshouldbe done byanauthorisedandregisteredinstaller. Hewill issue you
witha gascertificate. Amanualgasshut-off valvemustbe installedinthe gassupplyaheadofthe appliance inthe
gasstreamforsafetyandease ofservice.
üDonotstoreorusegasolineorotherflammablevaporsandliquidsinthevicinityofthisoranyother
appliance.
WHATTODOIFYOUSMELLGAS:
lDonottrytolightanyappliance.
lDonottouchanyelectricalswitch;
lDonotuse any phone inyourbuilding.
lImmediatelycall yourgassupplierfroma neighbor'sphone. Followthe gas
supplier'sinstructions.
lIf you cannotreachyourgassupplier.,.call the fire department.
üInstallation andservice mustbeperformedbyaqualifiedinstallerservice agency,oraregisteredsupplier
inordertoensure thewarrantyon thisproduct.
WARNING:IFTHE INFORMATIONINTHISMANUALISNOTFOLLOWEDEXACTLY,AFIRE OR
EXPLOSIONMAYRESULTCAUSINGPROPERTYDAMAGE, PERSONALINJURY, ORDEATH.
6 burners
BA
C
D
D
D
048
047
047 047
047
065
065
065 075
042
042
044
042 042
Position: 047 (Outer A Top Left, Outer A Top Right, Outer A Bottom Left, Outer A Bottom Right)
Position: 042 (Outer B Top Left, Outer B Top Right, Lower B Bottom Left, Lower B Bottom Right)
Position: 065 (Inner D Middle)
Position: 048 (Inner A Middle)
Position: 044 (Inner B Middle)
Position: 075 (Inner C Middle)
Liquid Gas Conversion/Replacement Kit
17
Each nozzle is lightly engraved and numbered. You may view the engraving by putting a light on the side of the
nozzle. There are only 6 types of nozzles identified by their numbers (047,042,065,048,044,075). Each nozzle
must be inserted into the correct department. This must be done by a technician or all warranties
are void.
1. Please ensure a white threaded sealant is used to avoid leakage around the threading of the nozzle prior to
insertion. This is mandatory.
2. Please shut all gas off to the appliance prior to configuration.
3. Please tighten each nozzle by hand until you can't turn any longer. Please then use a socket wrench and ONLY
turn one quarter turn clockwise. Any additional turning performed by the socket wrench can break the nozzle
compartment and destroy the burner assembly.
4. Please supply power to the gas and check for gas leaks by spraying the nozzles with a gas leak formula. If
bubbles are noticed and are expanding around the nozzle compartment, please shut off power to your gas supply
again and repeat steps 1-3 until no gas leaks are noticed.
Important Safety Instructions
2
WARNING WARNING
CAUTION
Power cord with three
prong grounding plug Three prong
electrical outlet
• Make sure all the cooktop parts are dry before
burner.
• Turn the knobs to the OFF position prior to removing
them from the valve stems.
• The cooktop should never be operated without the
knobs and trim rings in place.
• Use only dry pot holders when removing food and
cookware from the cooktop. Wet pot holders can cause
steam burns.
• When deep fat frying:
◊ Be certain that the pan is large enough to contain the
desired volume of food without overflow caused by
the bubbling of the fat. Never leave a deep fat fryer
unattended.
◊ Avoid frying moist or frost-covered foods. Foods
with high water content may cause spattering or
spilling of the hot fat.
◊ Heat fat slowly, and stir together any combination of
oils and fats prior to applying heat. Utilize a deep fat
frying thermometer to avoid heating the fat to
temperatures above the flash point.
• (Options, this appliance equipped with a three prong
plug for your protection against
possible electric shock hazards. If only a two prong
outlet is available, it is the customer’s responsibility
to have it replaced with a dedicated, grounded, three
prong electrical outlet by a licensed electrician. Do
not underany circumstances:)
◊ Cut or remove the third (ground) prong from the
power cord.
◊ Use an adapter plug.
◊ Use an extension cord.
◊ Use a power cord that is frayed or damaged.
◊ Plug the cooktop into an electrical outlet with a
ground fault interrupter (GFI).
TO REDUCE THE RISK OF INJURY TO PERSONS
IN THE EVENT OF A RANGE TOP GREASE FIRE:
a. SMOTHER FLAMES with a close-fitting lid,
cookie sheet or metal tray, then turn off the burner. BE
CAREFUL TO PREVENT BURNS. If the flames do
not go out immediately, EVACUATE AND CALL THE
FIRE DEPARTMENT.
b. NEVER PICK UP A FLAMING PAN - you may be
burned.
c. DO NOT USE WATER, including wet dish cloths or
towels - a violent steam explosion may result.
d. Use a fire extinguisher ONLY if:
◊ You have a Class ABC extinguisher, and you
already know how to operate it.
◊ The fire is small and contained in the area where it
started.
◊ The fire department is being called.
◊ You can fight the fire with your back to an exit.
• Do not allow acids (citrus juices, tomato sauces,
etc.) to remain on the cooktop’s surfaces. may stain
.
• Never use the cooktop surface as a cutting board.
• Do not try to remove heavy spills with a sharp object
such as a knife or metal spatula. Sharp objects may
scratch the cooktop’s surfaces.
• Do not expose the knobs or trim rings to direct flame,
hot utensils or other sources of heat.
Important Safety Instructions
3
Before You Call for Service
Problem Solution Guide:
Problem May Be Caused By What to Do
Nothing works.
Cooktop not connected to
electrical power.
Power to electrical outlet is off.
Power outage.
Check to make sure power cord is connected
to electrical outlet.
Turn on power at circuit breaker or fuse
box. Check for tripped breaker or blown
fuse.
Contact power company.
Igniter do not spark (no
clicking sound).
Power not supplied to unit.
Wet or dirty igniter(s).
See Nothing Works above.
Clean and dry igniter and burner assembly
according to Care and Cleaning
section.
No flame.
Igniter(s) not working.
Wet or dirty igniter(s).
Gas is turned off.
Gas supply interrupted.
See Igniter do not spark above.
Clean and dry according to Care and
Cleaning section.
Make sure the gas supply valve is in the
on position.
Contact gas company.
Burner goes out at lowsetting
Air intake holes obstructed.
Low gas pressure.
Check to make sure air holes above knobs
are not blocked.
Contact gas company to have pressure tested
Flame is distorted, yellow or
very large.
Burner parts are dirty or
clogged.
Burner parts are not properly
positioned.
Cooktop set up to use a different
type of gas (Natural or LP)
or set up for different altitude.
as regulator n
installed orfaulty.
Clean and dry according to Care and
Cleaning section.
Make sure burner is assembled according
to the section.
Have a service technician check
to make sure that the cooktop is set up
for the type of gas and the correct altitude.
Have a service technician check
the gas regulator.
Igniter continues to spark
(click) after flame ignites.
Burner is cold.
Flame distorted by air draft.
Wet or dirty igniter(s).
Burner parts wet or dirty.
Burner parts not positioned
.
Power supply polarity is
reversed.
Burners may continue to spark for up to
60 seconds when cold and set to low. See
Operating Your Cooktop section for
more information on how to minimize.
Minimize any air drafts around the cooktop.
Close nearby windows.
Clean and dry according to Care and
Cleaning section.
Clean and dry according to Care and
Cleaning section.
Make sure burner is assembled according
to the Setting Up Your Cooktop section.
Have a licensed electrician check the
electrical outlet.
16
IMPORTANTPRECAUTIONSAND RECOMMENDATIONS
lAfterhavingunpackedtheappliance, checktoensurethatit isnotdamaged.Ifyou haveanydoubts,donot
use it andconsult yoursupplierora qualifiedtechnician.
lPacking materials(i.e. plasticbags,polystyrenefoam,nails,packing straps,etc.)shouldnotbeleftaround
withineasyreachofchildren, asthesemaycauseseriousinjuries.
lThe packagingmaterialsare recyclable andismarkedwiththe recyclingsymbol .
lDonotattempttomodifythe technicalcharacteristicsofthe appliance asthismaybecome dangeroustouse.
lThemanufacturercannotbeconsideredresponsiblefordamagecausedbyunreasonable, incorrectorrash
use ofthe appliance.
lIf youshoulddecidenottousethisappliance anylonger(ordecidetosubstituteforanothermodel),before
disposingofit,itisrecommendedthatit bemadeinoperativeinanappropriatemannerinaccordance to
healthandenvironmentalprotection regulations, ensuring inparticularthatall potentiallyhazardouspartsbe
made harmless, especiallyinrelation tochildrenwho couldplaywitholdappliances.
lTheappliance shouldbeinstalledandall thegas/electricalconnectionsmadeby aqualifiedengineerin
compliance withlocalregulationsinforce andfollowingthemanufacturer'sinstructions.
IMPORTANTPRECAUTIONSANDRECOMMENDATIONSFORUSEOFELECTRICAL
APPLIANCES
Use ofany electricalappliance impliesthe necessitytofollowa seriesoffundamentalrules.Inparticular:
lNevertouchthe appliance withwethandsorfeet;
lDonotoperate the appliance barefooted;
lDonotallowchildrenordisabledpeople touse the appliance withoutyoursupervision.
Themanufacturercannotbeheldresponsibleforanydamagescausedby improper;incorrectorunreasonableuse
orinstallation ofthe appliance.
TIPSFORTHEUSER
lDuringandafteruse ofthe cooktops, certainpartswill become veryhot. Donottouchhotparts.
lKeepchildrenawayfromthe cookinghobwhenit isinuse.
lAfteruse, ensurethattheknobsareinpositionOFF,andclosethemaingasdeliveryvalveorthegas
cylindervalve.
lBefore anycleaningormaintenance, switchoffthe electricitytothe cooktops.
Riskoffire!
lDonotleave flammable materialon the cooktops.
lMakesurethattheelectricalcablesofotherappliancesinstallednearbycannotcomeintocontactwiththe
cooktops.
WARNING
Cleaning the Cooktop (continued)
Care and Cleaning
Knobs and Trim Rings
Never block the holes in the control panel behind the
knobs. Doing so will impair the flow of combustion air
and adversely affect burner operation, possibly
creating a hazardous condition.
To prevent damage, do not expose the knobs to direct
flame, hot utensils or other sources of heat.
• Turn the knobs to the off position before removing
them for cleaning or replacement.
• To remove the knobs, gently grasp each knob
and pull straight out, off of the valve shaft.
• Wash the knobs regularly with a solution of
warm soapy water. We recommends hand
dishwashing liquid.
• Clean the outside edges of the trim rings while
the knobs are removed. Do not remove the trim
rings. Wipe them with a soft damp rag. Use caution
to avoid getting moisture into the control
panel behind the trim rings.
• Replace the knobs according to the directions.
Be sure to install the knobs in their
proper positions
15
Getting to Know Your Cooktop
Parts of the Cooktop
6 burners
Burner Locations
A Triple Ring Burner : 17,000 BTU
B Triple Ring Burner : 15,000 BTU
C
D
Rapid Burner : 12,000 BTU
SaQJEBurner : 7,000 BTU
Burner
control knob
Burner
Grate
Burners T
cooktop’s system
generates a spark that lights the burner when
you turn the knob to HIGH. See the diagrams on the right
for the size and location of the different burner types.
Long Life Grates: The porcelain coated cast iron
grates support the cooking utensils during cooking.
They are removable allow the area below and
around the burners to be cleaned easily.
Spill Trays: The spill trays catch any food that falls
through the cooktop grates.
Burner Control Knobs: Use the knobs to turn on the
burners and adjust the flame size.
4
Installation RequirementsInstallation Requirements
WARNING
• Observe all governing codes and ordinances during
planning and installation. Contact your local building
department for further information.
• To prevent an electric shock hazard, the power supply
must meet the specifications stated below.
The electrical and gas supply data on this page is for
reference only. If the requirements below do not agree
with the product data label, use the data on the product
data label.
Electrical Requirements
• The electrical installation, including minimum
supply wire size and grounding, must be done in
accordance with National Electric Code ANSI/NFPA
70 and local codes and ordinances. A copy of this
standard may be obtained from:
National Fire Protection Association
1 Park
Quincy, MA 02269-9101
• The correct voltage, frequency and amperage must be
supplied to the electrical outlet according to the
product data label located on the bottom of the chassis.
• The electrical outlet must be installed by a licensed
electrician.
ELECTRIC CIRCUIT REQUIREMENTS
Circuit Required Total Connected Load
120 V 60Hz ,
Minimum 15 Amp.
0.25 Amp
@ 120 V, 60 Hz
Product Dimensions
Gas Supply Requirements
• Check your local building codes for the proper method
of installation. In the absence of local codes, this
appliance should be installed in accordance with the
National Fuel Gas Code ANSI Z223.1/NFPA 54. The
gas service must be installed by a qualified professional
• Be certain that the cooktop being installed is correct for
the gas service being provided (natural gas or LP gas).
Also, if operating the cooktop at an altitude above 4000
ft. (1219 m) make sure it is equipped for high altitude
operation. See the inside cover for more information.
• An external manual shut-off valve must be installed
between the gas inlet and the cooktop for the purpose
of turning on or shutting off gas to the appliance.
• A standard regulator be installed in the gas
lithat runs from the gas shut off valve to the cooktop
gas inlet. Use only a regulator inlet that accommodates
a 3/4” gas supply line and is also compatible with a
1/2” house gas supply.
The inlet to the cooktop itself equipped with a ” male
fitting
GAS SUPPLY PRESSURE REQUIREMENTS*
Gas Type Manifold
Pressure
Minimum Gas
Supply Pressure
Natural Gas
Propane (LP)
5” Water Column
10” Water
Column
6” Water Column
11” Water
Column
* Maximum gas supply pressure for all models is 1/2 p.s.i.
” gas inlet, connects to frombottom or rear of unit,
end is recessed2” (51 mm) from bottom.
Product tolerances: ±1/16” (±1.6 mm) unless otherwise
noted.
REAR VIEW
5
8 1/3 Inch
35 3/8 Inches
8 1/3”
23 5/8 “
35 3/8”
Electrical
Terminal
Box/Cover
Grate does not protrude in actual unit
Approximate position of
gas & electrical.
CAUTION
CAUTION
CAUTION
Continued...
Care and Cleaning
Burner Components and Igniter Grates, Spill Trays and WOK Ring
Use care while cleaning the igniter. The porcelain is
fragile and can crack or break.
IMPORTANT: The igniter may not spark or work
properly if the burner parts or the igniter themselves
are not clean and dry.
After disassembling the burners, check for any dirt
or grime deposited on the individual parts, including
the igniter.
1. Use a firm toothbrush to clean completely around
the igniter, including all of the metal top and porcelain
base. Use care while cleaning because the porcelain is
fragile and can crack or break. Do not use water to
clean the igniter. If necessary, use a small amount of
rubbing alcohol to help dissolve grime.
2. Examine the burner rings. Remove anything
stuck in the holes with a straightened paper
clip, wire or needle. Be careful not to scratch or
damage the ring and head. Do not distort the
shape of the burner ring holes.
3. Clean all of the burner parts, including the burner
bases, with window cleaner or rubbing alcohol. Use a
cleaning brush with plastic bristles or a firm tooth
brush. When done, rinse the parts well with clean water.
Dry all the parts thoroughly before re-assembling them.
4. Reassemble the cooktop according to the burner and
grate assembly instructions. Test the burners after
reassembling them. If the flame is uneven, be sure that
all the burner parts are properly positioned, then check
for any remaining dirt or grime on the burner parts or
igniter. If erratic sparking (clicking) is still present,
make sure the igniter is completely dry. If the unit still
exhibits problems after drying, call your local ervice gent.
CAUTION
Do not clean the cooktop grates, burner parts in a
dishwasher. They will be damaged.
The grates the spill tray are
coated with a porcelain finish.
• For everyday cleaning,use a soft cloth
or nonabrasivepad with warm
soapy water to clean all
of the porcelain parts.
• If necessary, tough
stains may be removed
by applying full-strength
sprays such as Simple
Green™, Ajax™ All-Purpose Cleaner or Formula
409™. To minimize wear, use the mildest cleaner
needed to get the surface clean.
• For extremely stubborn stains, you may use a
mildly abrasive cleaner or applicator, such as
Soft Scrub™, Bon Ami™, S.O.S. pads or other
soap-filled steel wool pads. Use these cleaners
with extreme care and only on occasion. Extensive
use of these types of abrasives will eventually
damage the porcelain enamel.
Stainless Steel Surfaces
Brass, Chrome and Copper Surfaces
Always wipe stainless steel (silver colored) surfaces.
To prevent scratching, do not use abrasive
cleaners or scrubbers on stainless steel surfaces.
•
.Rinse and dry with a soft, lint-free cloth.
To prevent scratching, do not use abrasive cleaners or
scrubbers on metal surfaces.
Using a soft cloth, clean metal surfaces with a mild
solution of
. Rinse and drywith a soft, lint-free cloth.
14
A / B Burner AssemblyC / D Burner Assembly
Burner cap
Outer burner cap
Inner burner cap
Burner ring Burner ring
Ignition pin Ignition pin
Thermocouple Thermocouple
Hole of the
burner base Hole of the
burner base
WARNING
CAUTION
Care and Cleaning
• Clean only the parts of the cooktop listed in this manual. Clean them only in the manner specified.
• To avoid dangerous fumes or damage to your cooktop’s surfaces and accessories, use only the types of cleaning
solutions specified in this manual.
• To avoid electrical shock or burns, turn off the burners and make sure that all parts are cool before cleaning.
DO NOT turn the burners on during cleaning.
• Do not use a steam cleaner to clean the cooktop. Steam could penetrate the electrical components and cause a
short circuit. After cleaning the burners, reassemble all of the burner parts before attempting to operate the
cooktop.
• After cleaning the burners, always dry and reassemble the cooktop parts completely before use.
• Do not try to remove heavy spills with a sharp object such as a knife or metal spatula. Sharp objects may
scratch your cooktop’s surfaces.
• To prevent damage, do not use abrasive or corrosive cleaners or applicators such as steel wool or scouring pads,
on any part of the cooktop unless instructed to do so. Use only a sponge, soft cloth, fibrous or plastic brush or
nylon cleaning pad for cleaning the surfaces of your cooktop.
• Do not remove the trim rings from the cooktop. Clean only the outside edges of the trim rings. If you get
moisture inside the trim rings damage to the cooktop may occur.
• Do not soak the knobs in water or put them in the dishwasher.
• Installing the cooktop knobs in the wrong position may result in damage to the cooktop .
riddle/grill kit
Cleaning the Cooktop
To keep the cooktop looking and operating its best,
clean it after every use. Also, quickly wipe up spills
that occur while cooking. Be careful not to touch any
hot areas. Spills that remain on hot burner parts
will be very difficult to clean, especially if allowed to
burn on. Certain types of food, such as tomatoes,
citrus juices, vinegar, alcohol and milk can damage
the finishes if you allow them to stand for any
length of time.
IMPORTANT: The cooktop is exposed to extremely
high temperatures. The grates are under high stress
when hot utensils are placed on them. Also, the
cooktop parts are occasionally exposed to acidic
food spill-overs. These severe operating conditions,
cause the porcelain enamel parts on your cooktop
to undergo a change in appearance over time. If
you care for and clean these parts carefully, you will
slow down, but not eliminate, the aging process.
Cooktop Disassembly
1. For safety, disconnect the cooktop power cord
from the electrical outlet prior to cleaning.
2. When the appliance is cool, remove the grates
from the top of the cooktop.
3. Disassemble the burners. Lift the burner caps
and burner rings off of the burners.
13
Not actual model frontal view displayed. General Photo
Installation RequirementsInstallation Requirements
Cabinet and Countertop Layout
WARNING
To avoid the risk of fire or personal injury, all minimum
and maximum specified clearances on this and the
following pages must be maintained or exceeded.
General Considerations
• The minimum distance from the back of the cooktop
to a combustible rear wall is 2 1/2” (64 mm) minimum
(Figure 1).
• Installation of a non-combustible material* (up to the
hood) or a backsplash is always recommended, and
mandatory if the distance to the back wall from the
cooktop is less than 2 1/2” (Figure 2).
* Consult local codes and ordinances for acceptable
non-combustible materials.
• Carefully check the location where the cooktop is to be
installed. For best performance, the cooktop should be
installed away from drafts caused by doors, windows
and heatingair conditioning outlets. To reduce the
risk of personal injury from reaching over a hot
appliance, avoid cabinet installations directly above.
• To reduce the risk of personal injury and to reduce
accumulated smoke in the room, strongly
recommends installing a range hood. A hood should
project forward a minimum of five (5) inches beyond the
face of the cabinets.
• The installation must allow access to the underside
of the cooktop for service and inspection purposes,
including the ability to turn off the cooktop gas supply
valve and electrical outlet.
• All contact surfaces between the cooktop and the counter
must be solid and level.
• The countertop overhang on the sides of the cutout
shown on the following pages cover the recessed
portions of the cooktop behind the control panel and
creates a seamless look for the installation.
• IMPORTANT: When installing the cooktop into a
laminated or synthetic countertop, radius the corners of
the cutout to help avoid cracking. Consult the countertop
manufacturer’s instructions for minimum corner radius,
reinforcement and heat protection requirements.
Gas and Electric Service Location
• The gas supply piping, gas shut-off valve and the
electrical outlet must be located so they do not interfere
with the cooktop when it is installed. If installing another
appliance in the cabinet below,
allow for the routing ofgas and electrical service out
the back of the unit.
• The shaded area on the facing page shows the
recommended location of the gas inlet and the electrical
outlet. For replacement purposes, the location of the
existing utilities may be utilized provided they do not
interfere with the sides or rear of the cooktop. Check
local building codes for permissible utility locations.
• For best performance and to minimize gas pressure
loss, attach gas supply regulatoras close as possible
to the cooktop gas inlet.
The installation must:
• Allow for access to the gas shut-off valve and regulator
when the unit is installed.
• Allow for access to the electrical outlet, when the
cooktop is in place so the power cord may be easily
disconnected if the unit needs service.
• Allow the (32”) power cord to reach the electrical outlet.
6
Grate does not protrude in actual unit
35.4”
30”
18”
WARNING
WARNING
Burner knob settings
Operating Your Cooktop
Selecting the Cookware
• To avoid burns and scalding, always turn pan handles
to a position where they cannot be easily hit. Also,
handles should not extend over adjacent burners.
Always set utensils gently onto the grates and center
them so that they are well-balanced.
• Do not drag cookware across the grates. Sliding may
damage the finish. Lift utensils to reposition them. Do
not drop them on the grate.
• Cookware with rough bottoms can cause permanent
damage to the coated surfaces on the grates.
• To avoid burns or a fire hazard, reduce the flame level
if it extends beyond the bottom of the utensil. Flames
extending up the sides are potentially dangerous.
For overall safety and best cooktop performance,
select the correct cooking utensil for the food being
cooked. Improperly selected cooking utensils will
not cook evenly or efficiently.
Use cookware that:
• Has flat, smooth bottoms.
• Is well balanced.
• Has tight fitting lids to keep heat, odors and steam in.
IMPORTANT: Avoid spills as much as possible.
The porcelain surfaces of the grates, spill trays and
burner caps are acid-resistant but not acid-proof.
Some foods can cause permanent damage if allowed
to remain on porcelain surfaces.
Lighting a Burner
• To avoid the chance of fire, explosion or carbon
monoxide poisoning, do not attempt to use your
cooktop without the burners completely and properly
assembled (see page 5). The burner rings spread the
flame evenly around the burner cap. The burner rings
must be properly seated for proper burner lighting and
operation.
• In the interest of safety, always light the burner before
putting the cooking utensil on the grate. Turn the
burner knob to the OFF position before removing the
utensil. Always check the position of the control knobs
to make sure the cooktop is off when you are finished
cooking.
• Do not turn the knob farther than the HIGH position
until lit. Doing so may result in a burst of flame that
could cause burns or damage to the surrounding area.
• Do not touch any part of the burner while the igniter is
sparking. An electrical shock could result.
• Never light the burners with a match or other open
flame.
• Always check to make sure all control knobs are in the
OFF position when you are finished cooking.
• If the gas does not ignite after four seconds or if the
flame goes out and gas escapes when attempting to
light a burner, turn the knob to the OFF position. Open
a window and allow at least five minutes for the gas to
dissipate. Then, repeat the lighting procedure.
Each burner control knob has a small diagram
next to it
1. To light a burner, push in gently on the knob and
turn it counter-clockwise to the HIGH position.
The igniter will spark (click) repeatedly until the
gas ignites. The burner should light within four
seconds.
11
Installation RequirementsInstallation Requirements
8
Cabinet/Countertop Dimensions (cont.)
Cutout tolerances +1/16” -0 (+1.6 mm, 0) unless otherwise noted.
Gas and electrical connections
Gas connection and power cord may be
routed through bottom or back of chassis
Increase countertop and overhang
additional 2 1/2” (64 mm) Min. for
combustible rear wall above
countertop
Non-combustible
rear wall, rear of
mounting platform
Gas/electrical utility cut-out in left rear corner of
mounting platform203 mm X 152 mm,
if gas and electrical are routed through bottom
3/8” (13 mm)
countertop overhang
½” (13 mm)
countertop
overhang
598 mm
11 7/16”
(291 mm)
/ ” di
bolt
1” thick mounting platform Min.
Cabinet face
below countertop
overhang
2” (51 mm)
1” (25 mm)
Cabinet/Countertop Cutout Dimensions - Top View
Please wait to obtain appliance prior to cutting dimensions.
10” (254 mm) min.
to combustible wall
above countertop,
both sides
Not actual position
of gas/electric
Table of contents
Popular Hob manuals by other brands
Emilia
Emilia EMCER64 Instruction manual / installation manual
CONTINENTAL EDISON
CONTINENTAL EDISON CETI2ZFLEX4B Instructions of use
Hotpoint Ariston
Hotpoint Ariston DD 751 P/HA operating instructions
NEFF
NEFF N K30 Series instruction manual
Caterlite
Caterlite DF824 instruction manual
Siemens
Siemens EF6 HNA Series user manual
