Costway EP24962US User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Follow Costway
Please give us a chance to make it right and do better！
Contact our friendly customer service department for help first.
Replacements for missing or damaged parts will be shipped ASAP!
USER’S MANUAL
Jump Starter
EP24962US

Contact Us!
Do NOT return this item.
Contact our friendly customer service department for help first.
E-mail
US: [e-mail]
UK: [e-mail]
Before You StartBefore You Start
Please read all instructions carefully.
Retain instructions for future reference.
Separate and count all parts and hardware.
Read through each step carefully and follow the proper order.
We recommend that, where possible, all items are assembled near to the
area in which they will be placed in use, to avoid moving the product
unnecessarily once assembled.
Always place the product on a flat, steady and stable surface.
Keep all small parts and packaging materials for this product away from
babies and children as they potentially pose a serious choking hazard.
02

SAFETY INSTRUCTIONS
Read the user instructions carefully before use.
Save them for future reference.
WARNING:
● Wear safety glasses. Incorrect handling may cause a risk of personal injury if
you get battery acid in your eyes, rinse your eyes with clean water for at least 10
minutes and then seek medical attention immediately.
● If the jump starter is handled wrongly, there is a risk of explosion and serious
personal injury and/or material damage.
● When the jump starter is not in use, the black inverter power switch should be
in the OFF position, to avoid the risk of personal injury and/or material damage
if the clamps short-circuit.
● Never short-circuit the clamps with any metal object or by allowing them to
touch each other.
● Check that the vehicle battery is 12V, or there will be a risk of explosion
and/or serious injury.
● Before you start the jump starter, check that the clamps are connected with the
right polarity, otherwise the device or the battery could explode and cause
serious injury and/or material damage.
● CAUTION: The jump starter cannot be used to replace the vehicle's own
battery.
● Only use the built-in charger. Other chargers may shorten the lifetime of the
battery or cause it to explode and cause personal injury or material damage.
TECHNICAL DATA
AC ADAPTOR
Model
Voltage
Amps
Battery type
GM022IC
12V
600A cranking amps（5s）
Lead-acid battery 12V 22AH
ETL certificated
INPUT 120V AC, 60Hz, 0.25A
OUTPUT 12V DC 1A
03

04

1. Pressure gauge
2. 12V outlet
3. Emergency lighting
4. Charging connection
5. Indicator light for correct/incorrect connection
6. Power switch for compressor/USB
7. 5V USB connection
8. Power switch
9. Indicator light for correct/incorrect connection
10. Indicator lights for charge level
11. Battery control button/switch for emergency light
12. Compressor compartment
13. Inverter fuse
14. Indicator light for inverter fault
15. 120V outlets
16. Indicator light for inverter
17. Inverter power switch
OPERATION
INTENDED USE
● The jump starter is intended to start cars, boats etc. with 12V batteries.
● The jump starter has a 12V outlet which can be used to power most appliances
that are designed to be connected to a 12V outlet (max. 15A).
● LED light for emergency lighting.
● 200W inverter to power appliances designed for 120V. Indicator lights for
inverter status.
● The built-in battery in the jump starter can be charged with an external charger
connected to the charging connection. The jump starter has a built-in overcharge
protection.
● 5 V USB connection for charging mobile phones etc.
● Indicator lights showing battery level.
05

CHARGE THE JUMP STARTER BATTERY
NOTE:
● Charge the built-in battery in the jump starter before using it for the first time.
● Check the charge level in the built-in battery by pressing the battery control
switch and reading the indicator lights. If the red indicator light comes on, the
battery should be charged.
● Always keep the battery fully charged for best results and battery life. The
battery capacity and lifetime will be affected if it is left discharged for a long
time.
● Charge the built-in battery in the jump starter every three months if not used.
● The battery will last longer if you follow the instructions below.
- Charge the battery before using it for the first time.
- Charge the battery fully after each use.
- Charge the battery fully every 3 months.
1. Connect the charger to a mains outlet.
2. Connect the charger plug to the socket.
- The three indicator lights flash in turn to show that the built-in battery is being
charged.
- It takes 6-40 hours to charge the built-in battery fully, depending on the
condition of the battery.
- When the battery is fully charged, the green indicator light comes on. Allow
charging to continue if possible, to prolong battery life.
3. Disconnect the charger.
POWER SUPPLY VIA 12V OUTLET
NOTE:
● The outlet has overload protection with automatic reset.
● The internal battery in the jump starter can be emergency charged from the
vehicle's 12V outlet. However, it cannot be charged fully in this way. Use the AC
charger in the usual case.
1. Open the cover over the outlet.
2. Connect the 12V product to the outlet.
06

JUMP STARTING OF ENGINE
WARNING:
● Make sure the vehicle battery is 12V, or there will be a risk of explosion and/or
serious injury.
● Before you start the jump starter, make sure the clamps are connected with the
right polarity.
● Follow the instructions below, otherwise there is a risk of personal injury
and/or material damage.
1. Switch off the ignition and all systems (lights, radio, air-conditioning etc.) in
the vehicle.
2. Connect the red positive clamp (+) on the jump starter firmly to the positive
terminal (+) on the vehicle battery.
3. Connect the black negative clamp (-) to the negative terminal (-) on the
battery or to a metal part of the vehicle. If the connection is made correctly, the
green light will come on.
4. Put the switch in the ON position.
5. Turn the ignition key to try to start the engine. Do not hold the key turned for
more than 5 seconds.
6. If the vehicle does not start, wait for at least 3 minutes and try again.
7. If the engine starts, set the power switch to the OFF position.
8. Disconnect the black negative cable (-) and put it away.
9. Disconnect the red positive cable (+) and put it away.
10. Recharge the built-in battery in the jump starter as soon as possible.
COMPRESSOR
WARNING: The compressor can be run continuously for maximum 10 minutes
and then it needs to cool down for at least 10 minutes. When inflating tires, the
pressure rise very quickly - pay attention.
07

Inflation
1. Open the compressor compartment and pull out the air hose.
2. Place the nozzle over the valve and press it right down. Fold down the locking
lever into the locked position.
3. Start the compressor with the compressor power switch.
4. Monitor the air pressure on the manometer until the desired pressure is
reached.
5. When the desired pressure has been reached, turn off the compressor with the
power switch, fold up the locking lever and disconnect the nozzle from the
valve. Replace the hose in the compressor compartment.
6. Use an adapter to inflate beach balls, air mattresses, inflatable boats etc.
INVERTER
● The inverter can supply 120VAC, 60Hz, 200W.
● To protect the battery, the inverter is fitted with under voltage protection. If the
voltage falls too low, an alarm will be emitted and the inverter will be switched
off. It will be reset automatically when the battery voltage is higher.
● The inverter is fitted with short-circuit protection, which switches off the jump
starter if the connected equipment short-circuits.
● If the indicator light on the inverter comes on, check that the connected
equipment is working correctly and does not need too much power for the jump
starter. Also check the charge level in the battery.
● The fuse trips in the following situations. Replace the fuse if necessary.
- If the connected equipment needs too much power.
- In the event of a short circuit in the connected equipment.
1. Set the inverter power switch to the ON position.
2. Insert the cable from the external equipment into the 120V outlet.
3. Start the external equipment.
4. The inverter can be switched off automatically or with the power switch.
08

MAINTENANCE
REPLACING THE BATTERY
WARNING: Do not burn batteries — risk of explosion.
1. Loosen the screws holding the back cover.
2. Separate the front and back covers so the battery is visible.
3. Remove the battery.
4. Unscrew the positive and negative wires from the battery.
5. Connect the red positive wire to the battery's positive terminal and the black
negative wire to the battery's negative terminal.
6. Place the new battery in the battery compartment.
7. Replace the back cover and tighten the screws.
8. Spent batteries must be disposed of in accordance with applicable regulations.
Care for the environment!
Must not be discarded with household waste! This product contains electrical or
electronic components that should be recycled. Leave the product for recycling
at the designated station e.g. the local authority's recycling station.
09

Welcome to visit our website and purchase our quality products!
We would like to extend our hearelt thanks to
all of our customers for taking me to assemble
this product and giving us valuable feedbacks.
With your inspiring rating, COSTWAY will be more consistent to offer you
EASY SHOPPING EXPERIENCE, GOOD PRODUCTS and EFFICIENT SERVICE!
US office: Fontana, California
UK office: Ipswich
Reward Points
Exclusive Customer Service
Personalized Recommendaons
Permanent Shopping Cart
Order History
10