COZY ROADIE CR-1015-01 User manual

Model Number: CR-1015-01
COZY ROADIE-EXECUTIVE OFFICE CHAIR
1. To Adjust Seat Height:
While seated, lean forward and reach under the right
side of the chair to find the handle. Lift the handle and
raise your body up slightly to allow the chair to rise to
the desired height. To lower the seat, lift the handle
whi l e applying more wei ght downward on t he s eat. The
chair will descend until the handle is released or the
chair reaches the bottom position.
2. To Operate Tilt Lockout:
While seated, reach under the right side of the chair to
find the height adjustment handle. Pull the handle all
the way ou t (away f rom t he seat plate) to allow the
chairto tilt backwards. To lock thechair inthe upright or
vertical position, sit upright and push the handle in
towards the seat plate.
3. To A djus t Tens ion on the Tilt Mechanism:
Reach under the front center of the chair, grasp the
round knob and turn counter - clockwiseto makethe tilt
mechanism firmer (stiffer). To make the tilt mechanism
less firm, turn the knob clockwise until the desired
resistance is found.
4. To Collapse the Chair Back Cushion:
Standing behind the chair, release the handle on the
back cover of the back cushion (diagram 1), push the
back cushion forward and fold the back cushion on seat
cushion (diagram 2). Important: Do Not Force! (Refer to
Diagram 1 and Diagram 2 for proper seat back
Operation)
5. 360° Swivel:
360° seat swivel.
OPERATING INSTRUCTIONS

Model Number: CR-1015-01
COZY ROADIE-EXECUTIVE OFFICE CHAIR
A. Remove all parts from case and separate them into part number groups as indicated in the parts list.
B. To b egin as s emb ly, place the Base (2) upside down and insert the Casters (1) into bottom of the Base (2).
C. Turn the Base (2) over and insert the Quick Release Gas Lift (3) into the center hole on the Base (2).
D. Attach Seat Plate (4) to the bottom of Seat and Back Cushion w/ Arms (5) (with the front of seat plate facing
the front of seat cushion) using the four Captive Knobs (4) and tighten knobs to the seat bottom.
E. Place the Pre-assembled Seat and Back Cushions w/ Arms (5) and Seat Plate (4) on top of Gas Lift (3) and
press down until fully engaged.
F. Standing in front of the chair, push the seat back cushion into an upright position. Check to mak e sure the pins
have lock ed into the arm holes correctly. (Refer to Diagram 1 and Diagram 2 for proper assembly)
G. Periodically (every 90 days) make sure that the screws and k nob are still fully tightened.
ATTENTION: M ake certain all Thumb Screws on seat plate are fully snugged before using chair. Do Not
Over Tighten.
NOTE: Any adjustments made to the position of the upper quick release on the gas cylinder must be
made with the quick release positioned flush against the “tilt -swi ve l plate” on the underside of the chair
seat, an d n ot so h i gh o n th e cyl i n der, th at i t i m ped es th e g as cyl i n der fro m secure l y p ress -fitting into the
seat-plate. Once assembled, carefully sit in the chair, full weight, to press fit it together. It
is Operator/Assembler's responsibility to safely determine that the chair is indeed fully press-fit together
and ready for use. Operator/Assembler assumes full responsibility for safe assembly of the chair for
himself and others who may use it. Cozy Roadie assumes no responsibility for improperly assembled
chairs.
Part #
Description
Quantity
1.
2.
3.
4.
5.
6.
Casters
Heavy Duty Base
Quick Release Gas Lift
Seat Plate wi t h Captive Knobs
Seat and Back Cushions w/
Arms (no assembly needed)
Allen Key
5
1
1
1
1
1
PARTS LIST
ASSEMBLY INSTRUCTIONS
For tightening the
arms, if necessary
No tools nec es s ar y