CR-Tec CR-Laser Fit-F User manual

NON-INTERLOCKED HOUSING WARNING
This unit contains high power laser devices internally. Do not open the
laser housing, due to potential exposure to unsafe levels of laser radiation.
The laser power levels accessible if the unit is opened can cause instant
blindness, skin burns and fires.
LASER EMISSION DATA
As measured under IEC measurement conditions for classification.
Version: 3.0
This manual contains important laser operation information. Read and
understand all instructions prior to powering on laser unit the first time, to
avoid laser eye injury and to avoid breaking the law. Keep this manual in a
safe place for future reference.
Laser Classification Class 3B
Green Laser Medium DPSS Nd:YVO4, 532nm
Red Laser Medium 650nm LD
Beam Diameter <5mm at aperture
Pulse Data All pulses < 4Hz (>0.25sec)
Divergence (each beam) <2 mrad
Divergence (total light) <160 degrees
Laser Power Red>100mW, Green>30mW

USER MANUAL
2
PRODUCT OVERVIEW
zThis device has left out premises in absolutely perfect condition. In order to
maintain this condition and to ensure a safe operation, it is necessary for the
user to follow the safety instructions and warning notes written in this
manual.
zThe manufacturer will not accept liability for any resulting damages caused
by the non-observance of this manual or any unauthorized modification to
the device.

USER MANUAL
3
CONTROL & FUNCTION
zRegular breaks during operation are essential to maximize the life of this
device as it is not designed for continual use.
zDo not switch the unit on and off in short time intervals
zAlways unplug the unit when it is not used for a longer time. Or before
replacing the bulb or start servicing.
zIn the event of serious operation problems, stop using the fixture and
contact your dealer immediately.
NO. NAME DESCRIPTION
1 Power LED Indicates the fixture is switched on
2 Music LED Synchronize to detected music signal
3 Laser Aperture
The laser effect output aperture. NEVER LOOK
INSIDE THE FIXTURE THROUGH THIS
APERTURE WHILE FIXTURE IS OPERATING.
4 Power Switch Switch ON and OFF the fixture
5 Fuse Holder The replaced fuse is hold here
6 Main Power Input With IEC socket and integrated fuse holder.
7 DMX
Input/Output 3 pins male/female XLR connector
8 Control panel To control the fixture with digital LED display, check
more information on CONTROL & FUNCTION
9 Microphone To detect the music/sound signal
ATTENTION: Laser will be output from laser aperture in 5 seconds
after the unit is powered on.

USER MANUAL
4
Operation
Stand Alone Preprogram Laser Show
zPress FUNC to enter MODE OPTION.
zTill to LED panel shows either one of Aut, Aup,Aud & Sou.
zPress UP or DOWN to select your favorite Stand Alone mode as above.
zPress ENTER to confirm the setting.
The laser is working in stand alone. Each time when you turn on your laser, you
will have this confirmed laser show.
In the MODE OPTION setting, the stand alone laser show that you are going to
choose is flashing. Press UP or DOWN to change stand alone laser show, you will
have 4 different stand alone preprogrammed laser show. Their DISPLAY and
EFFECT are listed below:
DISPALY STAND ALONE MODE LASER EFFECT
ArA Mixed laser effect Auto show with rAndom order
SrA Sound activated mixed laser effect show with rAndom order
Sod Sound activated solidbeam with double burst grating effect
SoP Sound activated Pattern effect show with random order

USER MANUAL
5
SOUND ACTIVATED MODE sensitivity setting
zPress FUNC till to see S 6
zPress UP/DOWN to set microphone sensitivity. S 0 is no sound activated,
from S 1 to S 9, the sensitivity level is going more sensitive.
zPress ENTER to confirm and save the setting.
MASTER/SLAVE MODE
zPress FUNC to enter MODE OPTION
zTill to LED panel shows SLA
zPress ENTER to confirm the setting.
The laser is working in “SLAVE MODE”. Connect MASTER laser and SLAVE
lasers with DMX cable, the SLAVE lasers do what exactly MASTER laser does.
Check “5.2 DMX connection”to have more details about laser connection.
DMX MODE
zPress FUNC to enter MODE OPTION
zTill to LED panel shows 001.
zPress ENTER to confirm the setting.
The laser is working in “DMX MODE”. With help of UP/DOWN button, it could be
easily change the DMX address of the laser.

USER MANUAL
6
DMX PROTOCOL
CANNEL DMX VALUE DESCRIPTION
CH 1
MODE
000-019 Laser Block Out
020-075 ARA Mixed Effect Auto Mode
076-131 SRA Sound Activated Mixture Mode
132-188 SOD Sound Activated Moving Dots Mode
189-239 SOP Sound Activated Firework Mode
240-255 DMX MODE
CH 2
Color
selection
000-036 Blackout
036-072 Red
073-108 Green
109-144 Red &green (alternate strobe)
145-180 Red on & Green strobe
181-216 Green on & Red strobe
216-255 Red & Green strobe
CH 3
Strobe
000-004 No function
005-254 Strobe (fast-slow)
255-255 Strobe to sound
CH 4
Rotation
000-004 No function
005-127 Clockwise rotation (slow-fast)
128-133 Stop
134-255 Counterclockwise rotation (slow-fast)
CH 5
Swing 000-255 Swing range (short –long)

USER MANUAL
7
SPECIFICATIONS
Mains Input:
Fuse:
Total Power:
Music Control:
Laser Power:
Laser Classification:
Laser Safety Standard:
Condition Temperature:
DMX Connections:
DMX Channels
Measurement:
N Weight:
AC100-240V, 50/60Hz
250V 1A Slow Blow (20mm Glass)
12W
Internal microphone
100mW-R + 30mW-G CW
Class 3B
EN60825-1 2007
10~40℃
3 pins XLR Male/Female
8 channels
145x160x80mm
1.8 Kg
Specifications subject to change without prior notice.
The availability of particular products may vary by region. Please check with the dealer.