CR-Tec CR-LASER SUPER-1 User manual

Version: 2.0
This manual contains important laser system safety and operation
information. Read and understand all instructions prior to powering on
laser unit the first time, to avoid laser eye injury and to avoid breaking
the law. Keep this manual in a safe place for future reference.

USER MANUAL
1
WARNING DATA
Lasers can be hazardous and have unique safety considerations.
Permanent eye injury and blindness is possible if lasers are used
incorrectly. Pay close attention to each safety REMARK and
WARNING statement in the user manual. Read all instructions
carefully BEFORE operating this device.
Attention!
Important!
Caution!
Laser!
Recycle
Indoor
Disposal
Location
Indicates a skill or other useful information for special
situations.
Indicates important information to protect people from laser
incident or injury.
Prevent damage or injury from incorrect operation.
Laser safety warming labels.
To protect the environment, recycle packing material
wherever possible.
The projector is for indoor use only, IP20. Use only in dry
locations. Keep this device away from rain and moisture,
excessive heat, humidity and dust. Do not allow contact with
water or other fluids.
Don’t throw this product away just as general trash, please
dispose of this product following the abandon electronic
product regulations in your area.
The projector must be installed in a location with adequate
ventilation, at least 50cm (20 inches) from adjacent surfaces.
Be sure that no ventilation slots are blocked.

USER MANUAL
2
LASER SAFETY WARNINGS
Caution: Avoid direct eye contact with laser light. Never
intentionally expose your eyes or others to direct laser
light.
Caution: This laser product can potentially cause instant eye
injury or blindness if laser light directly strikes the eyes.
Caution: It is illegal and dangerous to shine this laser into
audience areas, where the audience or other personnel
could get direct laser beams or bright reflections into
their eyes.
Caution: It is a US Federal offense to shine any laser at aircraft.
Caution: There are no user serviceable parts inside the unit. Do
not open the housing or attempt any repairs yourself. In
the unlikely event your unit may require service, please
contact the dealer nearest to you..
NON-INTERLOCKED HOUSING WARNING
This unit contains high power laser devices internally. Do not open the laser
housing, due to potential exposure to unsafe levels of laser radiation. The laser
power levels accessible if the unit is opened can cause instant blindness, skin
burns and fires.
Potential laser injury hazard exists with this product! Read these
instructions carefully, which includes important information about
installation, safe use and service!

USER MANUAL
3
LASER SAFETY AND OPERATING INSTRUCTIONS
STOP AND READ ALL LASER SAFETY DATA
Laser light is different from any other light source with which you may be familiar.
The light from this product can potentially cause eye injury if not set up and used
properly.
Laser light is thousands of times more concentrated than light from any other
kind of light source. This concentration of light power can cause instant eye
injuries, primarily by burning the retina (the light sensitive portion at the back of
the eye). Even if you can not feel “heat” from a laser beam, it can still potentially
injure or blind you or your audience. Even very small amounts of laser light are
potentially hazardous even at long distances. Laser eye injuries can happen
quicker than you can blink.
It is incorrect to think that because these laser entertainment products split the
laser into hundreds of beams or laser beam is scanned out in high speed, that
an individual laser beam is safe for eye exposure. This laser product uses
dozens of milliWatts of laser power (Class 3B levels internally). Many of the
individual beams are potentially hazardous to the eyes.
It is also incorrect to assume that because the laser light is moving, it is safe.
This is not true. Nor, do the laser beams always move. Since eye injuries can
occur instantly, it is critical to prevent the possibility of any direct eye exposure.
In the laser safety regulation, it is not legal to aim Class 3B lasers in areas which
people can get exposed. This is true even if it is aimed below people’s faces,
such as on a dance floor.
zDo not operate laser without first reading and understanding all safety and
technical data in this manual.
zAlways set up and install all laser effects so that all lasers light is at least 3
meters (9.8 feet) above the floor on which people can stand. See “Proper
Laser Set-up & Usage” section later in this manual
zDo not point lasers at people or animals.
zNever look into the laser aperture or laser beams.
zDo not point lasers in areas in which people can potentially get exposed,
such as uncontrolled balconies, etc.

USER MANUAL
4
zNever point a laser at aircraft, this is a federal offense.
zNever point un-terminated laser beams into the sky.
zDo not expose the output optic (aperture) to cleaning chemicals.
zDo not use laser if the laser appears to be emitting only one or two beams.
zDo not use laser if housing is damaged or open, or if optics appear
damaged in any way.
zNever open the laser housing. The high laser power levels inside of the
protective housing can start fires, burn shin and will cause instant eye
injury.
zNever leave this device running unattended.
zThe operation of a class 3B laser show laser is only allowed if the show is
controlled by a skilled and well-trained operator familiar with the data
included in this manual.
zThe legal requirements for using laser entertainment products vary from
country to country; the user is responsible for the legal requirements at the
location/country of use.
zAlways use appropriated lighting safety cables when hanging lights and
effects overhead.
LASER SAFETY LABEL REPRODUCTIONS
This is only one laser aperture
on this product. The label
indicates the laser beam output
aperture.
Caution – Class 3B LASER
RADIATION, WHEN OPEN,
AVOID EXPOSURE TO BEAM
LASER RADIOATION AVOID
EXPOSURE TO BEAM CLASS
3B LASER PRODUCT.

USER MANUAL
5
LASER EXPOSURE WARNING
LASER LIGHT
AVOID DIRECT EYE EXPOSURE
Further guidelines and safety programs for safe use of lasers can be found in
the ANSI Z136.1 Standard “For Safe Use of Lasers”, available from
“www.laserinstitute.org”. Many local governments, corporations, agencies,
military and others, require all lasers to be used under the guidelines of ANSI
Z136.1. Laser Display guidance can be obtained via the International Laser
Display Association, www.laserist.org.
LASER EMISSION DATA
* As measured under IEC measurement conditions for classification.
LASER COMPLIANCE STATEMENT
This laser product complies with EN/IEC 60825-1 Ed 2, 2007-03, and US
FDA/CDRH FLPPS via the terms of Laser Notice No. 50 dated June 24, 2007.
Laser Classification Class 3B
Green Laser Medium DPSS Nd:YVO4,532nm
Beam Diameter <5mm at aperture
Divergence(each beam) <2 mrad
Divergence(total light) <90 degrees
Laser power G>100mW
Transverse Beam Mode TEM00
Cooling TEC & Fan Cooling
Scanning DC to 20KHz, ±25 Degrees X & Y

USER MANUAL
6
GENERAL SAFETY INSTRUCTIONS
Every person involved with installation and maintenance of this device has to:
zBe qualified
zFollow the instructions of this manual
This device has left out premises in absolutely perfect condition. In order to
maintain this condition and to ensure a safe operation, it is necessary for the
user to follow the safety instructions and warning notes written in this manual.
Important! The manufacturer will not accept liability for any resulting
damages caused by the non-observance of this manual or
any unauthorized modification to the device.
zPlease consider that damages caused by manual modifications to the
device are not subject to warranty.
zNever let the power-cord come into contact with other cables! Handle the
power-cord and all connections with the mains with particular caution!
zMake sure that the available voltage is not higher than stated on the rear
panel.
zAlways plug in the power plug least. Make sure that the power-switch is set
to off-position before you connect the device to the mains. The power-plug
has to be accessed after installing the device.
zMade sure that the power-cord is never crimped or damaged by sharp
edges. Check the device and the power-cord from time to time.
zAlways disconnect from the mains, when the device is not in use or before
cleaning it. Only handle the power-cord by the plug. Never pull out the plug
by tugging the power-cord.
zIt is essential to connect the yellow/green conductor to earth.
zThe electric connection, repairs and servicing must be carried out by a
qualified employee.
CAUTION! Be careful with your operations. With a high voltage
you can suffer a dangerous electric shock when
touchin
g
the wires!

USER MANUAL
7
zDo not switch the fixture on and off in short intervals as this would reduce
the laser diode life.
zFor replacement, please use fuses of same type and rating only.
zIf the device has been exposed to drastic temperature fluctuation, do not
switch it on immediately. The arising condensation water might damage
your device. Leave the device switched off until it has reached room
temperature.
zDo not shake the device. Avoid brute force when installing operating the
device.
zWhen choosing the installation-spot, please make sure that the device is
not exposed to extreme heat moisture or duct. There should not be any
cables lying around. You endanger your own and the safety of others!
zThe minimum distance between the fixture and surrounding walls must be
more than 50cm.
zAlways fix the fixture with an appropriate safety-rope. Fix the safety-rope at
the safety-rope only.
zThe ambient temperature must be between 10℃to 40℃.
zPlease use the original packaging if the device is to be transported.
zPlease consider that unauthorized modifications on the device are
forbidden due to safety reasons!
CAUTION! Operate the device only after having familiarized with its
functions. Do not permit operation by persons not qualified
for operating the device. Most damages are the result of
unprofessional operation!
CAUTION! If this device will be operated in any way different to the one
described in this manual, the product may suffer damages and
the warranty void.

USER MANUAL
8
BEFORE OPERATION
Unpacking Instructions
CAUTION! Immediately upon receiving a fixture, carefully unpack
the carton, check the contents to ensure that all parts are
present, and have been received in good condition.
Notify the shipper immediately and retain packing
material for inspection if any parts appear damage from
shipping or the package itself shows signs of
mishandling. Save the package and all packing materials.
In the event that a fixture must be returned to the factory,
it is important that the fixture be returned in the original
factory box and packing.
What is Included
The carton or flight case contain following items:
Power Supply
To determine the power requirements for a particular fixture, see the label
affixed to the back plate of the fixture of refer to the fixture’s specifications chart.
A fixture’s listed current rating is its average current draw under normal
conditions. All fixtures must be powered directly off a switched circuit and can
not be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat
or dimmer channel is used solely for a 0% to 100% switch. Before applying
power to a fixture, check that the source voltage matches the fixture’s
requirement.
NAME QTY
Laser Light 1 PCS
KEYs (for key switch) 2PCS
Power Cord 1 PCS
Interlock Connector 1 PCS
USER MANUAL 1 PCS

USER MANUAL
9
The unit is supplied with a power plug appropriate to its voltage and destination.
Should any other connections be required they must be carried out with the
following configuration.
DMX-512 connection between fixtures
The fixture is equipped with 3-pin XLR sockets for DMX input and output. The
sockets are wired in parallel. Only use a shielded twisted-pair cable designed for
3-pin XLR-plugs and connectors in order to connect the controller with the
fixture or one fixture with another.
Occupation of the XLR-connection
Caution! At the laser fixture, the DMX-cable has to terminate with
a terminator. Solder a 120 Ohm resistor between Signal (-)
and Signal (+) into a 3-pin XLR-plug and plug and plug it in
the DMX-output of the last fixture.
Cable(EU) Cable(US) Pin International
Brown Black Live L
Light blue White Neutral N
Yellow/Green Green Earth

USER MANUAL
10
Building a serial DMX-chain
zIf you are using the standard DMX-controllers, you can connect the
DMX-output of the controller directly with the DMX-input of the first fixture
in the DMX-chain. If you wish to connect DMX-controllers with other
XLR-outputs, you need to use adapter cables.
zConnect the DMX-output of the first fixture in the DMX-chain with the
DMX-input of the next fixture. Always connect output with the input of the
next fixture until all fixtures are connected.
zIf you use a controller with 5 pins DMX connector, you need to use a 5 to 3
pins adapter.
zAt last fixture, the DMX cable has to be terminated with a terminator.
Solder a 120 Ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+)
into a 3 pins XLR-plug and plug it in the DMX-output of the last fixture.
zConnect the fixture together in a daisy chain by XLR plug cable from the
output of the fixture to the input of the next fixture. The cable cannot be
branched or split to a Y cable. DMX 512 is a very high speed signal.
Inadequate or damaged cables, soldered joints or corroded connectors
can easily distort the signal and shut down the system.
zThe DXM output and input connectors are pass-through to maintain the
DMX circuit, when power is disconnected to the unit.
zEach fixture needs to have a DMX address to receive the data from the
controller. The DMX address number which could be read from rear panel
of each fixture is between 000~511.
zThe end of the DMX 512 chain should be terminated to reduce signal
errors.

USER MANUAL
11
Proper Laser Set Up & Usage
This fixture has been designed to be hung. It is recommended for safety
purposes, your lighting effect are properly mounted using a suitable hanging
clamp and safety cable. Items appropriate for safe and effective mounting are
easily sourced from your lighting vendor.
International laser safety regulations require that lasers must be operated in the
fashion illustrated below, with a minimum of 3 meters (9.8 ft) of vertical
separation between the floor and the lowest laser light vertically. Additionally, 2.5
meters of horizontal separation is required between laser light and audience or
other public spaces.
Rigging the Fixture
CAUTION: Use of controls, adjustments, or performance of
procedures other than what is specified herein may
result in hazardous radiation ex
p
osure
CAUTION: Please consider the respective national norms during the
installation! The installation must only be carried out by an
authorized em
p
lo
y
ee or dealers!

USER MANUAL
12
zThe installation of the fixture has to be built and constructed in a way that it
can hold 10 times the weight for 1 hour without any harming deformation.
zThe installation must always be secured with a secondary safety
attachment, e.g. an appropriate catch net. This secondary safety
attachment must be constructed in a way that no part of the installation can
fall down if the main attachment fails.
zMake sure the area below the installation place is free from unwanted
persons during rigging, de-rigging and servicing.
zThe operator has to make sure that safety-relating and machine-technical
installations are approved by an expert before taking into operation for the
first time and after changes before taking into operation another time.
zThe operator has to make sure that safety-relating and machine-technical
installations are approved by a skilled person once a year.
zThe fixture should be installed in the position where persons cannot reach
and where persons may walk by or be seated.
CAUTION: When installing the device, make sure there is no highly in
inflammable material (decoration articles, etc.) in between a
distance of min 0.5 meter.

USER MANUAL
13
RODUCT OVERVIEW
Rear Panel
NO NAME FUNCTION
1 Switch Switch on and off the power
2 Mains input With socket and integrated fuse holder
3 DMX output 3PIN Female XLR port，using for DMX
4 DMX input 3PIN Male XLR port, using for DMX
5 Urgent and safe switch Switch off the laser manually if error occurs
6 Key switch Make sure the professional person use
7 Cooling fan Cooling and never cover this fan outlet
8 LED control Panel Intelligent LED control panel of the system
9 Safety eye Attach the safety cable
10 ILDA / Hardware Setting Sound, Music, ILDA, Patterns Setting

USER MANUAL
14
ILDA / Hardware Setting Panel
NO NAME FUNCTION
11 X SIZE
Y SIZE The Size of X / Y axis adjustment
12 X MIRROR
Y MIRROR
X / Y axis mirror setting (It could be done by
LCD control panel as well)
13 MIC Microphone. Turn the knob to adjust the
sound activated sensitivity.
14 ILDA INPUT Standard ILDA DB25 Input
15 ILDA OUT Standard ILDA DB25 Output(thought)
16 R G B Laser beam output indicator LED.
17 ILDA ILDA connection indicator LED. Green is
connection and red is disconnection.

USER MANUAL
15
Front Panel
NO NAME FUNCTION
19 POWER Indicates that the unit is switched on.
20 DMX DMX connection indicated LED. Red is
DMX connected, Green is preprogram
standalone mode.
21 MUSIC Flashes to the sound of the music
detected by the mic
22 Laser output Laser output aperture.
23 HANGING
BRACKET
With 2 knobs on both sides to fasten the
unit and a mounting hole to fix a
mounting hook.
24 WARNING LABEL laser aperture
25 WARNING LABEL Caution-Class 3B laser
26 LASER WARNING
SIGN Warms against apotentially dangerous
laser when not used by skilled operators.
27 WARNINGLABEL Laser radiation Avoid exposure to beam.
Class 3B laser product.

USER MANUAL
16
IMPORTANT
For your own safety and full laser
safety regulation, we do
strongly recommend you to
take this optional switch!
CONTROL & FUNCTION
zRegular breaks during operation are essential to maximize the life of this
device as it is not designed for continual use.
zDo not switch the unit on and off in short time intervals
zAlways unplug the unit when it is not used for a longer time. Or before
replacing the bulb or start servicing.
zIn the event of serious operation problems, stop using the fixture and contact
your dealer immediately.
zAttention Laser will be output from laser aperture in 5 seconds
after the unit is powered on.
Operating Mode
When laser is powered on, LED monitor on rear panel shows the current
operating standalone mode or DMX address of DMX mode. With help of LED
control panel, is very easy to set and change the operating mode of laser. After
every resetting and saved, the new mode information will be shown on LED
monitor at next power on.
Mode/Function Option, to choose the operating mode of laser.
Confirmation, to confirm all setting or change of LED control panel.
UP/DOWN, to change operating mode, parameter or DMX address.

USER MANUAL
17
Operation
Stand Alone Preprogram Laser Show
zPress FUNC to enter MODE OPTION.
zTill to LED panel show any one of “A1, A2, S1 , S2”.
zPress UP or DOWN to select your favorite Stand Alone mode as above.
zPress ENTER to confirm the setting.
The laser is working in stand alone. Each time when you turn on your laser, you
have this confirmed laser show.
In the MODE OPTION setting, the stand alone laser show that you are going to
choose is flashing. Press UP or DOWN to change stand alone laser show, you
will have 4 different stand alone preprogrammed laser show. Their DISPLAY and
EFFECT are listed below:

USER MANUAL
18
DISPLAY STAND ALONE MODE LASER EFFECT
A1 Auto laser show with random order
A2 Auto laser show with traditional order
S1 Sound activated laser show with random order
S2 Sound activated laser show with traditional order
Attention: In S1 or S2 MODE (Sound Activated Mode), the
laser will be blocked out in 3 second when MIC Signal
was not detected.
DMX MODE
zPress FUNC to enter MODE OPTION
zTill to LED panel shows 001.
zPress UP or DOWN to select the DMX 512 ADDRESS among 001-512.
zPress ENTER to confirm the setting
The laser is working in DMX MODE. With help of UP and DOWN button, the
DMX address could be set.
zAttention In DMX MODE, once the DMX cable is connected with
laser and DMX controller, the DMX LED in front panel of
laser will be ON.
SLAVE MODE
zPress FUNC to enter MODE OPTION.
zTill to LED panel shows SLA
zPress ENTER to confirm the setting
The laser is working in “SLAVE MODE”. Connect MASTER laser with several
SLAVE laser with DMX cable, the SLAVE lasers do what exactly the MASTER
laser does. Please check “5.2 DMX connection” to have more details about laser
connection.

USER MANUAL
19
PATTERN MIRROR REVERSE SETTING
zPress FUNC to enter MODE OPTION
zTill to LED panel show any one of , , , .
zPress UP or DOWN to select pattern mirror mode as above.
zPress ENTER to confirm the setting.
In the MODE OPTION setting, the pattern mirror mode that you are going to
choose is flashing. Press UP or DOWN to change pattern mirror mode, you will
have 4 different pattern mirror mode. Their DISPLAY and OUTPUT are listed
below：
DISPLAY PATTERN MIRROR
OUTPUT DISPLAY PATTERN MIRROR OUTPUT
zAttention Beside of LED programmed mirror reverse setting, the
laser scanned world could be set by ILDA control panel.