Craftsman 917.250051 User manual

®
MODEL NUMBER 917.250051 OWNER'SMANUAL
Assembly
Operation
Customer
Responsibilities
Service
Adjustments
Repair Parts
aution:
cad and Follow
I Safety Rules
_d Instructions
efore Operating
his Equipment

SAFETY RULES &
Safe Operation Practices for Ride-On Mowers
IMPORTANT: THIS CUTTING MACHINE ISCAPABLE OFAMPUTATING HANDS AND FEET AND THROWING OBJECTS.
FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
I. GENERAL OPERATION
•Read, understand, and follow all instructions in the manual
and on the machine before starting.
•Only allow responsible adults, who are familiar with the
instructions, to operate the machine.
•Clear the area of objects such as rocks, toys, wire, etc,
which could be picked up and thrown by the blade.
•Be sure the area isclear of otherpeople before mowing. Stop
machine if anyone enters the area.
• Never carry passengers.
• Do not mow in reverse unless absolutely necessary. Always
leek down and behind before and while backing.
,, Be aware of the mower discharge direction and do not point
it at anyone. Do not operate the mower without either the
entire grass catcher or the guard in place.
° Slow down before turning.
•Never leave a running machine unattended. Nways turn off
blades, set parking brake, stop engine, and remove keys
before dismounting.
• Turn off blades when not mowing.
° Stop engine before removing grass catcher or unclogging
chute.
• Mow only in daylight or good artificial light.
° Do not operate the machine while under the influence of
aicoho! or drugs.
° Watch for traffic when operating near or crossing roadways.
•Use extra care when loading or unloading the machine into
atrai_eror truck.
U, SLOPE OPERATION
Slopes are a major factor related to toss-of=controland tipover
accidents, which can result in severe injury or death. AHslopes
require extra caution. Ifyou cann otback up the slope orifyou feel
uneasy on it, do not mow it.
DO:
•Mow up and down slopes, not across.
•Remove obstacles such as rocks, tree limbs, etc.
° Watch for holes, ruts, or bumps. Uneven terrain could
overturn the machine. Tall grass can hide obstacles.
• Use slow speed. Cheese alow gear so that you wilf not have
to stop or shift while on the slope.
• Follow the manufacturer's recommendations for wheel
weights or counterweights to improve stability.
= Use extra care with grass catchers or other attachments.
These can change the stability of the machine.
•Keep all movement on the slopes slow and gradual Do not
make sudden changes in speed or direction.
° Avoid starting or stopping on a slope. If tires lose traction,
disengage the blades and proceed slowly straightdewn the
slope.
DO NOT:
•Do not turn on slopes unless necessary, and then, turn slowly
and gradually downhill, if possible.
.Do notmow near drop-offs, ditches, or embankments. The
mower could suddenly turn over if a wheel is over the edge
of a cliff or ditch, or if an edge caves in.
•Do not mow on wet grass. Reduced traction could cause
sliding.
•Do not try to stabilize the machine by putting your foot on the
ground.
•Do not use grass catcher on steep slopes.
ill. CHILDREN
Tragic accidents can occur if the operator is not afert to the
presence ofchildren. Children are often attracted tothe machine
and the mowing activity. Neverassume that children will remain
where you last saw them.
• Keep children outofthe mowing area and underthe watchful
care of another responsible adult.
•Be alert and tum machine off ifchildren enter the area.
• Before and when backing, look behind and down for small
children.
= Never carry children. They may fall off and be seriously
injured or interfere with safe machine operation.
• Never allow children to operate the machine.
•Use extra care when approaching blind corners, shrubs,
trees, or other objects that may obscure vision.
IV. SERVICE
•Use extra care inhandling gasoline and otherfuels. They are
flammable and vapors are explosive.
Use only an approved container.
Never remove gas cap or add fue! with the engine
running. Allow engine to cool before refueling. Do not
smoke.
Never refuel the machine indoors.
Never store the machine or fuel container inside where
there is an open flame, such as a water heater.
. Never run a machine inside a closed area.
, Keep nuts and bolts, especially blade attachment bolts, tight
and keep equipment in good condition.
=Never tamper with safety devices. Check their proper
operation regularly.
•Keep machine free of grass, leaves, or other debris build-up.
Clean oil or fuel spillage. Allow machine to cool before
storing.
o Stop and inspect the equipment if you strike an object.
Repair, if necessary, before restarting.
• Never make adjustments or repairs with the engine running.
° Grasscatchercomponentsaresubjecttowear, damage,and
deterioration, which could expose moving parts or allow
objects to be thrown. Frequently check components and
replace with manufacturer's recommended parts, when nec-
essary,
, Mower blades are sharp and can cuL Wrap the blade(s) or
wear gloves, and use extra caution when servicing them.
o Check brake operation frequently. Adjust and service as
required,
_r this symbol to_
fety precautions, It means !
N!II BECOME ALERT!!! YOUR i
IS INVOLVED, J
CAUTION: Always disconnect spark
plug wire and place wire where it cannot
contact spark plug in order to prevent
accidental starting when setting up,
transporting, adlusting or making
repairs.

CONGRATULATIONS on your purchase of a Sears
tractor. It has been designed, engineered and manufac-
tured to give you the best possible dependability and
performance.
Should you experience any problem you cannot easily
remedy, please contact your nearest Sears Service
CentedDepartment. We have competent, welt-trained
technicians and the proper tools to service or repair this
tractor.
Please read and retain this manual. The instructions will
enable you to assemble and maintain your tractor prop-
erly. Always observe the "SAFETY RULES".
MODEL
NUMBER 917.250051
SERIAL
NUMBER
DATE OF PURCHASE
THE MODELAND SERIAL NUMBERSWILL BE FOUND
ON A PLATE UNDER THE SEAT.
YOU SHOULD RECORD BOTH SERIAL NUMBER AND
DATE OF PURCHASE AND KEEP tN A SAFE PLACE
FOR FUTURE REFERENCE.
MAINTENANCE AGREEMENT
PRODUCT SPECiFiCATiONS
HORSEPOWER: 20.0
GASOLINE CAPACITY: 3.5 GALLONS
UNLEADED REGULAR
OIL (3.8 PINTS w/Fitter) SAE 30 (above 32°F)
(3.5 PINTS w/o FILTER) 5W-30 (below 32°F)
SPARK PLUG (GAP.025tN.): CHAMPION RV15YC
VALVE CLEARANCE: INTAKE .003- .006 IN.
EXHAUST .016-.019 IN.
GROUND SPEED: (MPH):
LO HI
1st .8 1.8
2rid 1.4 3.4
3rd 2.4 5.5
Rev. .9 2.1
TRANSAXLE OIL NON-DETERGENT
(4 QUARTS CAPACITY) SAE30 (ISO 100)
TIRE PRESSURE: FRONT: 14 PSI
REAR: 10 PSi
CHARGING SYSTEM: 15 AMPS @ 3600 RPM
BLADE BOLT TORQUE: 30-35 FT. LBS.
A Sears maintenance agreement is available on this prod-
ucL Contact your nearest Sears store for details.
CUSTOMER RESPONSlBILnT ES
Read and observe the safety rules.
, Follow a regular schedule in maintaining, caring for and
using your tractor.
Follow the instructions under "Customer Responsibili-
ties" and "Storage" sections of this manual,
WARNING: This tractor is equipped with an internal
combustion engine and should not be used on or near any
unimproved forest-covered, brush-covered or grass-cov-
ered land unless the engine's exhaust system is equipped
with a spark arrester meeting applicable local or state laws
lif any). Ifa spark arrester is used, it should be maintained
neffective working order by the operator.
In the state of California the above is required by taw
(Section 4442 of the California Public Resources Code).
Other states may have similar laws. Federal laws apply on
federal lands. A spark arrester for the muffler is available
through your nearest Sears Authorized Service Center/
Department (See REPAIR PARTS section of this manual
LIMITED TWO YEAR WARRANTY ON ELECTRIC START RIDING EQUtPiVIENT
For two years from date of purcl_ase, when this riding equipment is maintained, iubricated, and tuned up according to the
operating and maintenance instructions in the owner's manual, Sears will repair free of charge any defect in material or
workmanship.
This Warranty does net cover:
* Tire replacement or repair caused by punctures from outside objects (such as nails, thorns, stumps, or glass).
,Expendable items which become worn during normal use, such as blades, spark plug, air cleaners and belts.
* Repairs necessary because of operator abuse or negligence, including bent crankshafts and the failure to maintain the
equipment according to the instructionscontained in the owner's manual.
Riding equipment used for commercial or rentat purposes.
FULL 90 DAY WARRANTY ON BATTERY
For 90 days from date of purchase, if any battery included with this riding equipment proves defective in material or workmanship
and our testing determines the battery will net hold a charge, Sears wilt replace the battery at no charge.
WARRANTY SERVICE iS AVAILABLE BY RETURNING THE RIDING EQUIPMENT TO THE NEAREST SEARS SERVICE
CENTER/DEPARTMENT IN THE UNITED STATES.
This Warranty gives you specific legal rights, and you may also have other rights which ,vary from state to state.
SEARS, ROEBUCK AND CO., D/8t7 WA, HOFFMAN ESTATES, ILLINOIS 60179

TABLE OF CONTENTS
SAFETY RULES ............................................................ 2
PRODUCT SPECIFICAT!ONS .................................... :_3
CUSTOMER RESPONSIBiLiTiES ..................... 3, 13-1{}
WARRANTY .................. _,................................................ 3
TABLE OF CONTENTS ................................................. 4
iNDEX ............................................................................ .4
TRACTOR ACCESSORIES ........................................... 5
ASSEMBLY ................................................................ 7-9
OPE RATION ........................................................... 10-t 2
MAINTENANCE SCHEDULE ...................................... 13
SERVICE AND ADJUSTMENTS ............................ 17-20
STORAGE .................................................................... 2t
TRO UBLESHOOTtNG ............................................ 22=23
REPAIR PARTS -TRACTOR ................... :............. 25-38
REPAIR PARTS -ENGINE ..................................... 40-49
PARTS ORDERING/SERViCE ................... BACK PAGE
iNDEX
A
Accessories ............................................ 5
Adjustments:
Brake ........................................... 17
Carburetor ................................... 20
Clutch .............................. i........... 17
Throttle Control Cable ................. 20
Toeqn .......................................... 18
Air Filter, Engine ................................. 16
Air Screen, Engine .............................. 15
Assembly ........................................... 7-9
8
Battery:
Charging ........................................ 8
Cleaning ...................................... t 4
installation ..................................... 9
Levels ....................................... 8,!4
Preparation .................................... 8
Starting with Weak Battery .......... 19
Storage ........................................ 21
Terminals .................................... 14
Be_t:Motion Drive
Removal/Replacement ........... 18
Brake Adjustment ............................... 17
C
Carburetor Adjustment ....................... 20
Clutch Adjustment. ............................ !7
Controls, Tractor ................................. 10
Customer Responsibilities .......... 3,13-16
Engine:
Air Filter ................................... 16
.Air Filter Foam Pre-Cieaner .... 16
Air Screen, Engine .................. 15
Battery ..................................... 14
Cooling Fins, Engine ............... 15
Engine Oil ................................ 15
Fuel Filter ................................ 16
Spark Plugs ............................. 16
Tractor:
Lubrication Chart ..................... 13
Maintenance Schedule ............ t 3
Tire Care .............................. 8,19
E
Electrical:
Interlocks and Relays .................. 19
Schematic ................................... 24
Wiring Diagram ............................ 26
Engine:
Air Filter ....................................... 16
Air Filter Foam Pre-Cleaner ........ 16
Air Screen ................................... 15
Cooling Fins, Engine ................... 15
Oil Change .................................. 15
Oi! Level ................................... 8,14
Oil Type ....................................... 15
Preparation .................................. 12
Repair Parts ........................... 40-49
Starting ........................................ 12
Storage ........................................ 21
F
Filter:
Air Filter ....................................... 16
Air Filter Foam Pre-Cieaner ........ 16
Fuel ............................................. 16
Oil ................................................ 16
Fuel:Type ............................................ 12
Storage ........................................ 21
Fuse .................................................... 19
H
Hood Remova!/Installation .................. 20
L
Lubrication Chart ..................... _.......... 13
M
Maintenance Schedule ....................... 13
Muffler ................................................ 16
Spark Arrester .......................... 3,30
O
O_l:Cold Weather Conditions ....... t2,15
Fi_ter ............................................ 16
Engine ......................................... t 5
Storage ........................................ 21
Transaxle .................................... t 4
Operation ...................................... 10-12
Options:
Accessories ................................... 5
Spark Arrester .......................... 3,30
P
Parking Brake ................................ 10-11
Parts Bag ................ .............................. 6
Parts, Replacement/Repair ........... 25-38
Product Specifications ........................... 3
R
Repair Parts .................................. 25-37
S
Safety Rules ......................................... 2
Seat ...................................................... 8
Service and Adjustments ............... 17-20
Carburetor ................................... 20
Clutch .......................................... 17
Fuse ............................................ 1g
Hood Removal/installation .......... 20
Motion Drive Belt
Removal/Replacement ........... 18
Tire Care ................................... 8,t9
Toeqn .......................................... 18
Slope Guide Sheet ............................. 51
Spark Plugs. ....................................... 16
Specifications ....................................... 3
Starting the Engine ............................. 12
Steering Wh eel ................................ 7,18
Stopping the Tractor ........................... 11
Storage ............................................... 21
T
Throttle Control Cable
Adjustment .................................. 20
Tires ................................................... 8,19
Trouble Shooting Chart .................. 22-23
Transaxle:
Oil Level ...................................... 14
Repair Parts........................... 36-37
W
Warranty ............................................... 3
Wiring Diagram ................................... 26
Wiring Schematic ................................ 24

ACCESSORmES AN ATTACHMENTS
These accessories and attachments were available when the tractor was purchased. They are also available at most Sears retail outlets,
catalog and service centers. Most Sears stores can order these items for you when you provide the model number of your tractor.
ENGINE SPARK PLUG GAS CAN ENGINE OiL FUEL STABILIZER MAINTENANCE
PERFORMANCE
Sears offers a wide variety of attachments that fit your tractor. Many of these are listed below with brief explanations of how they can help
you. This list was current at the time of publication however, it may change in future years - more attachments may be added, changes
may be made in these attachments, or some may no longer be available or fit your mode. Contact your nearest Sears store for the
accessories and _ttachments that are available for your tractor.
Most of these attachments do not require additional hitches or conversion kits (those that do are indicated) and are designed for easy
attaching and detaching.
AERATOR promotes deep root growth for a healthy lawn, Tapered
2,5qnch steel spikes mounted on 10-inch diameter discs puncture
holes in soil at c_ose intervals to let moisture soak in. Steet weight tray
for increased penetration.
BUMPER protects front end of tractor from damage.
CARTS make hauling easy. Variety of sizes available, plus accesso-
ries such as side panel kits, tool caddy, cart cover, protective mat, and
dolly,
CORING AERATOR takes small plugs out of soil to allow moisture
and nutrients to reach grass roots. 36-inch swath. 24 hardened steel
coring tips, 150 Ib, capacity weight tray.
DISC HARROW has 2 gangs of 4 steel b_ades that angle from 10 to
20 degrees, 40 inches wide. Can hook2 units in tandem. (Requires
sleeve hitch.)
DOZER BLADE removes snow; grades dirt, sand an(] gravel, 48
inches wide, 17 inches high, clears 444nch path when angled. Master
lift control lever for operator ease. Spring trip for snow removal on
uneven pavement; built-in float for blade to follow ground contour.
Reversible, replaceable scraper bar. (Use with tire chains, wheel
weights or rear drawbar weight.)
EASY OIL DRAIN VALVE makes oiJ changes easier, faster.
FRONT END LOADER system includes double wide rear tires, rear
weight box, and hydraulically operated 5.26 cu.ft, bucket, Available
for horizontal engine garden tractors only. (Catalog onty,)
FRONT NOSE ROLLER canters in front of mower deck to reduce
chances of "scalping" on uneven terrain. Available for 38", 42" and
44" mower decks only.
GANG HITCH lets you tow 2 or 3 puiFbehind attachments at
once, such as sweepers, dethatchers, aerators (not for use with
rollers, carts or other heavy attachments).
GAUGE WHEELS on both sides of the mower deck reduce chances
of "scalping" on uneven terrain. For mower decks not so equipped.
MULCH RAKF_JDETHATCHER loosens soi_ and flips thatch and
matted leaves to lawn surface for easy pickup. Twenty spring tine
teeth. Useful to prepare bare areas for seeding. Available for front or
rear mounting. HiGH PERFORMANCE REAR-ACTION SPRING
TIN E DETHATCHER covers 36-inch wide path and tosses thatch into
large hopper.
MULCHING K_T, once installed, lets you mutch, discharge or bag
clippings (bagger optional) without changing blades. For models not
equipped as 3 in One Convertible mowers.
PLOW turns soil 6 inches deep, cuts 10-inch furrow. Crank adjust-
ment controls depth, 3-position yoke sets width_ Heavy steel landslide
for straight furrowing. (Requires sleeve hitch.)
RAMP TOPS AND FEET let you toad and unload tractor from a
pickup truck, Use with 2 x 8 or 2 x 10 lumber.
REAR BLADE is 42 inches wide and operated from driver's seat.
Reversible steel blade can be angled at 30 degrees for grading.
Reverses for snow plowing. (Requires sleeve hitch.)
ROLLER for smoother lawn surface. 36-inch wide, 18-inch diameter
waterqight drum holds up to 390 Ibs, of weight. Rounded edges
prevent harm to turf. Adjustable scraper automatically cleans drum. 5
SLEEVE CULTIVATOR is 43 inches wide. Prepares ground for
seeding, helps weed control Steel frame holds 5 adjustable sweeps.
Adiusts venticalty, horizontally. (Requires sleeve hitch.) Optional
accessory: steel furrow opener for wider openings for potatoes,
corn, and other deep-seeded crops.
SLEEVE HITCH for use with master lift system. Single pin couples/
uncouples.
SNOWTHROWER has 40-inch swath. Drum-type auger handles
powdery and wet/heavy snow. Mounts easily with simple pin arrange-
ment. Discharge chute adjusts from tractor seat. 6-inch diameter
spout discharges snow 10 to 50 feet. Lift controlled at tractor seat.
(Use with chains, wheel weights, or rear drawbar weight,)
SPRAYERS use 12-volt DC electric motor that connects to the tractor
battery or other 12-volt source, Includes booms for automatic
spraying when pulling, and hand held wand for spot spraying, Wand
has adjustable spray pattern. For applying herbicides, insecticides,
fungicides, and liquid fertilizers.
SPREADER/SEEDERS make seeding, fertilizing, and weed killing
easy. Broadcast spreaders are also useful for granular de-icers and
sand.
SWEEPERS let you collect grass clippings and leaves,
TILLER has 8 hp engine to prepare seed beds, cultivate, and corn post
garden residue. Chain-drive transmission. Six 1l-inch diameter one
piece heat-treated steel tines. Tills 30cinch path. (Requires sleeve
hitch.)
TILLER has 5 hp engine and 36-inch swath to prepare seed beds,
cultivate, and compost garden residue. Tiller has its own built-in lift
and depth control system and does NOT require a sleeve hitch. Fits
any lawn, yard or garden tractor. Simply hook up to the tractor
drawbar and go! Optional accessories convert unit for dethatching,
aerating, hi_ting...without tools.
TIRE CHAINS are heavy duty; closely spaced extra-large cross links
give smooth ride, outstanding traction.
TRACTOR CAB has heavy duty vinyl fabric over tubular steel frame,
ABS plastic top; clear plastic windshield offers 360 degree visibility.
Hinged metal doors with catch. Keeps operator warm and dry.
Remove vinyl and windshields for use as sun protector in summer.
Optional accessories include: tinted/tempered sotid safety glass
windshield with hand operated wiper; 12-vott amber caution light for
mounting on cab top.
TRACTOR COVER protects tractor from weather. Made of Evolution
3 fabric (water-repellent, extremely breathable, light weight, soft, non-
abrasive, pliable in all temperatures, durable, stain/tear/puncture
resistant, will not shrink or stretch). (Catalog only.)
VACS for powerful collection of heavy grass clippings and leaves.
Wand attachment to pick up debris in hardoto-reach places.
VAClCHtPPER includes a chipper-shredder,
WEIGHT BRACKET for drawbar for snow removal applications, Can
be mounted on front of tractor for plowing applications. Uses (1) 55
Ib. weight.
WHEEL WEIIGHTS for rear wheels provide needed traction for snow
removal or dozing heavy materials.

CONTENTS OF DWARE PAC
Parts Bag contents shown full size
(1) Shoulder Bolt 5/16q8
(1) Knob
(1) Washer 17/32 x 1-3/16 x 12 Gauge
(2) Hex Bolts t/4-20 x 3/4
(2) Hex Nuts 1/4-20
(2) Washers 9/32 x 5/8 x 16 Ga.
(2) Lock Washers 1/4
(2) Wing Nuts 1/4-20
Parts packed separately in carton
Seat ÷
8artery acid
Steering Wheet Bakery
Steering
Sleeve
Parts bag contents not shown ful! size
(2) Keys _! teering
Wheel
Insert
(2) Battery Carriage Bo|ts 1/4-20 × 7-1/2
Terminal Guard
15° Stope Sheet
L q
I................
"1
Battery Caps
and Instructions

Yournewtractorhasbeenassembledatthefactorywiththeexception of those parts left unassembled for shipping purposes.
To ensure safe and proper operation of your tractor, all parts and hardware you assemble must be tightened securely. Use
the correct tools as necessary to insure their proper tightness.
TOOLS REQUmRED FOR ASSEMBLY
A socket wrench set will make assembly easier. Standard
wrench sizes are listed.
(2) 7/16" wrenches (1) Tire pressure gauge
(1) 9/19" wrench (t) Adjustable wrench
(1) 1/2" wrench (1) Utility knife
When right and left hand is mentioned in this manual, it
means when you are in the operating position (seated
behind the steering wheel).
TO REMOVETRACTOR FROMCARTON
UNPACK CARTON
• Remove aH accessible loose parts from carton (See
page 6),
• Cut along lines on the carton, from top to bottom, all
four corners of carton and lay panels flat.
• Check for any additional loose parts or cartons and
remove,
BEFORE ROLMNG TRACTOR OFF SKiD
ATTACH $TEERRNG WHEEL (See Fig. t)
oRemove hex bolt, lock washer and large flat washer
from steering shaft.
, Position front wheels of the tractor so they are pointing
straight forward,
, Slide the steering sleeve over the steering shaft.
oPosition steering wheel so cross bars are horizontal
(left to right) and slide onto adapter.
= Secure steering wheel to steering shaft with hex bolt,
lock washer and large flat washer previously removed.
Tighten securely.
= Snap insert into center of steering wheel.
, Remove protective plastic from tractor hood and grill.
IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES
IN SKID THAT MAY PUNCTURE TfRES WHERE TRACTOR
IS TO ROLL OFF SKID.
TO ROLL TRACTOR OFF SKRD(See Fig, 2)
Release parking brake by depressing clutch/brake
pedal.
o Place gearshift lever in "NEUTRAL" position.
Roll tractor backwards off skid.
._ / STEERING
INSERT
_:i/BOLT _LOCK
i;! // WASHER
(_f'_ _FLAT WASHER
STEERING
WHEEL
ADAPTER
STEERING SHAFT
STEERING SLEEVE
FiG. 1
CLUTCH/BRAKE PEDAL
?°
GEARSHIFT LEVER PARKING BRAKE
FIG. 2
7

ASS
HOW TO SET UP YOUR TRACTOR
PREPARE BATTERY (See Fig. 3)
CAUTION: Wear eye and face shield.
Wash hands or clothing immediately ff
_ accidentallyincontactwithbatteryacid.
Oo not smoke. Fumes from charged
battery acid are explosive.
Read the instructions included with the
battery vent caps. Always wear gloves,
c_othing and goggles to protect your
hands, skin and eyes.
Your tractor has a battery charging system which is suffi-
cient for normal use. However; periodic charging of the
battery with an automotive charger will extend its life.
See instructions packed with vent caps in parts bag.
o Fill battery with acid. Fitl each cell until it reaches the
bottom of the vent wells. Do not overfill.
Allow battery to stand and settle for at least thirty
minutes. After standing, check the level of acid. If
below the vent wells, add more acid until the correct
level is reached.
While battery isstanding (after adding acid) and later, while
battery is being charged, continue with assembly of tractor.
ItV'iPORTANT: TO MAXiMiZE THE LIFE OF YOUR
BATTERY, IT IS NECESSARY THAT THE BATTERY BE
CHARGED BEFORE USE. FAILURE TO CHARGE
BATTERY CAN RESULT tN A SHORTENED BATTERY
LIFE.
o Charge battery at a rate of 6 amperes for 1 hour. Use
a 12 volt battery charger. Observe all safety precau-
tions required for battery charging.
*Check the acid level after the battery ischarged. If the
acid has fallen below the correct level, add distilled or
iron free water,
o Install the vent caps to cover the vent wells. Wash the
top of the battery with water to remove any acid, then
wipe dry.
, Check battery case for leakage to make sure that no
damage has occurred in handling.
o Dispose of excess battery acid. Neutralize acid for
disposal by adding it to four inches of water in a five
gallon ptastic container. Stir with a wooden or plastic
paddle while adding baking soda until the addition of
more soda causes no more foaming.
Follow instructions on how to install battery_
VENT CAP
VENT WELL
BATTERY
CELL ACiD
LY
iNSTALL SEAT (See Fig. 4)
Adjust seat before tightening adjustment knob.
•Remove cardboard packing on seat pan.
• Place seat on pan and assemble shoulder bolt.
• Assemble adjustment knob and fiat washer loosely.
Do not tighten.
Tighten shoulder bolt securely.
•Lower seat into operating position and sit on seat.
,Slide seat until a comfortable position is reached which
allows you to press clutch/brake pedal all the way
down.
Get off seat without moving its adjusted position.
Raise seat and tighten adjustment knob securely.
SEAT PAN
SHOULDER
BOLT
ADJUSTMENT
KNOB
SEAT
FLAT WASHER
FIG. 4
CHECK TiRE PRESSURE
The tires on your tractor were overinflated at the factory for
shipping purposes. Correct tire pressure is important for
best cutting performance.
, Reduce tire pressure to PSI shown in "PRODUCT
SPECIFICATIONS" on page 3 of this manual.
CHECK BRAKE SYSTEM
After you learn how to operate your tractor, check to see
that the brake is properly adjusted. See "TO ADJUST
BRAKE" in the Service and Adjustments section of this
manual.
FiG, 3
8

ASSEMBLY
HNSTALL BATTERY {See Figs, 5 & 6)
CAUT1ON: Do not short battery termi-
nals. Before installing battery, remove
metal bracelets, wristwatch bands,
rings, etc.
Positive terminal must be connected
first to prevent sparking from acciden-
ts! grounding.
,Raise hood.
,Make sure drain tube is fastened to drain hole in battery
tray and battery tray is positioned in hole of battery
support.
o Place battery in plastic tray, battery terminals to front of
tractor.
• First connect RED battery cable to positive (+) battery
terminal with hex bolt, flat washer, lock washer and hex
nut as shown. Tighten securely.
Connect BLACK grounding cable to negative (-) battery
terminal with remaining hexbolt, fiat washer, Iockwasher
and hex nut. Tighten securely.
Slide the two battery bolts through the terminal guard
and start the wing nuts onto the threads.
• Position terminal guard over the battery as shown, lower
bolts into key holes and slide square shafts of bolts into
slots of key holes.
Tighten wing nuts by hand making sure battery bolts
remain in slots of the key holes in the battery support.
Be sure terminal access doors are closed.
Use terminal access doors for:
Inspection for secure connections (totighten hardware).
Inspection for corrosion.
• Testing battery.
Jumping (if required).
® Periodic charging.
FLAT WASHER
(POSITtVE)
RED CABLE
HEXBOLT
(NEGATIVE)
CABLE
LOCK WASHER DRA|N TUBE
WING NUTS
BATTERY BOLT
KEY HOLE
DOORS
CAPS
BATTERY TRAY
RG. 6
JCHECKLIST
BEFORE YOU OPERATE AND ENJOY YOUR NEW
TRACTOR, WE WISH TOASSURE THAT YOU RECEIVE
THE BEESTPERFORMANCE AhID SATISFACTION FROM
THIS QUALITY PRODUCT.
PLEASE REVIEW THE FOLLOWING CHECKLIST:
,/ All assembly instructions have been completed.
,/ No remaining loose parts in carton.
¢" Battery isproperly prepared and charged. (Minimum 1
hour at 6 amps).
,/ Seat is adjusted comfortably and tightened securely.
¢" Al! tires are properly inflated. (For shipping purposes,
the tires were overinflated at the factory).
,/ Be sure mower deck is properly leveled side-to-side!
front-to-rear for best cutting results. (Tires must be
properly inflated for leveling).
•/Check mower and drive belts. Be sure they are routed
properly around pulleys and inside all belt keepers.
¢" Check wiring. Sse that all connections are stilf secure
and wires are properly clamped.
WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY
EXTRA A TTENTION TO THE FOLLOWING IMPORTANT
ITEMS:
¢Engine oil is at proper level.
¢Fuel tank is filled with fresh, clean, regular unleaded
gasoline.
¢ Become familiar with all controls-their location and
function. Operate them before you start the engine.
_' Be sure brake system is in safe operating condition.
FiG. 5
9

OPERATIC
KNOW YOUR TRACTOR
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR,
Compare the illustrations with your tractor to fami/iarize yourself with the location of various controls and adjustments. Save
this manual for future reference.
LIGHT SWITCH
ATTACHMENT CLUTCH SWITCH
THROTTLE CONTROL
CLUTCH/BRAKEPEDAL
iGNITION SWITCH
PARKING BRAKE
LEVER
HEIGHT
ADJUSTMENT
KNOB GEARSHJFTLEVER RANGE SHIFT LEVER
FiG° 7
Sears tractors conform to the safety standards of the American National Standards Institute.
ATTACHMENT CLUTCH SWITCH- Used toengage mower
blades or other attachments mounted to your tractor.
LIFT SW_TCH - Used to raise and lower mower deck or
other attachments mounted to your tractor. Ignition switch
must be on to operate this switch.
AMMETER - Indicates battery charging (+) or discharging
(-).
CLUTCH/BRAKE PEDAL -Used for declutching and
braking the tractor and starting the engine,
HEMGHTADJUSTMENT KNOB - Used toadjust the mower
height,
GEARSHIFT LEVER: Selects the speed and direction of
tractor.
THROTTLE CONTROL - Used to control engine speed.
RANGE SHIFT LEVER - Allows "Hi" or "LO" speed for all
forward and reverse gears.
iGNITiON SWITCH - Used to start and stop the engine.
LIGHT SW_TCH - Turns the headlights on and off.
PARKING BRAKE LEVER - Locks clutch/brake pedaJ into
the brake position.
CHOKE CONTROL - Used when starting a cold engine.
10

OPERATION
l_ The operation of any tractor can result in foreign objects thrown into the eyes, which can result in 1
severe eye damage. Always wear safety glasses or eye shietds before starting your tractor and while I
maving. We recomme,d wide visien safety mesk for overthe ,pectaeles._or_s!_
HOW TO USE YOUR TRACTOR
TO SET PARKING BRAKE (See Fig. 8)
Your unit is equipped with an operator presence sensing
switch. When engine is running, any attempt by the
operator to leave the seat without first setting the parking
brake will shut off the engine.
*Depress clutch/brake pedal intofull "BRAKE" position
and hold.
oPlace parking brake lever in "ENGAGED" position and
release pressu re from clutch/brake pedal. Pedal should
remain in "BRAKE" position. Make sure parking brake
wilt hold tractor secure.
ATTACHMENT
CLUTCH
SWITCH
"ENGAGED"
POSiTiON
iGNE|ON KEY
CHOKE
CLUTCH/BRAKE
PEDAL"BRAKE"
HEIGHT
ADJUSTMENT
KNOB
FiG. 8
THROTTLE
CONTROL LEVER
_PARKING
POSIT_ON
_'_'DiSENGAGED"
POStTION
JGEARSHIFT
VER
RANGE
SHIFT
LEVER
TO USE CHOKE CONTROL (See Fig= 8)
Use choke control whenever you are starting a cold engine.
Do not use to start a warm engine.
- To engage choke control, pull knob out. Slowly push
knob in to disengage.
TO USE THROTTLE CONTROL (See Fig. 8}
Always operate engine at full throttle.
.Operating engine at less than fuji throttle reduces the
battery charging rate,
.Full throttle offers the best mower performance.
TO MOVE FORWARD AND BACKWARD
(See Fig. 8)
The direction and speed of movement is controlled by the
gearshift lever.
*Start tractor with clutch/brake pedal depressed and
gearshift tever in "NEUTRAL" position,
o Move gearshift and range shift levers to desired posi-
tion.
-Slowly release clutch/brake pedal to start movement.
iMPORTANT: BRING TRACTOR TO A COMPLETE STOP
BEFORE SHiFTiNG OR CHANGING GEARS, FAILURE
TO DO SO WiLL SHORTEN THE USEFUL LiFE OF YOUR
TRANSAXLE.
STOPPING (See Fig. 8)
MOWER BLADES -
o Move attachment clutch switch to "DISENGAGED"
position.
GROUND DRIVE
o Depress clutch/brake pedal into full "BRAKE" position.
Move gearshift lever to "NEUTRAL" position.
ENGINE -
Move throttle control to "SLOW" position.
NOTE: Faiture to move throttle control to "SLOW" position
or allowing, engine to idle before stopping may cause
engine to backfire.
o Turn ignition key to "OFF" position and remove key.
Always remove key when leaving tractor to prevent
unauthorized use.
o Never use choke to stop engine.
NOTE: Under certain conditions when tractor is standing
idle with engine running, hot engine exhaust gasses may
cause "browning _'of gras& To eliminate this possibility,
always stop engine when stopping tractor on grass covered
areas.
TO OPERATE ON HILLS
Choose the slowest speed before starting up or down
hitls.
o Avoid stopping or changing speed on hills.
if slowing is necessary, move throttle control to slower
position.
If stopping is absoluteiy necessary, push clutch!brake
pedal quickly to brake position and engage parking
brake.
o Move gearshift lever to 1st gear and range shift lever to
"LO" position. Be sure you have allowed room for
tractor to roll slightly as you restart movemenL
o To restart movement, slowly release parking brake and
clutch/brake pedal.
o Make all turns slowly.
11

OPERATION
TO TRANSPORT
,Raise attachment lift to highest position with liftcontrol.
, When pushing or towing your unit, be sure gearshift
lever is in "NEUTRAL" position.
•Do not push or tow unit at more than five (5) MPH.
NOTE: To protect hood from damage when transporting
yourtractor on a truck or a trailer, be sure hood isclosed and
securedtotractor. Use an appropriate means of tying hood
to tractor (rope, cord, etc.).
BEFORE STARTING THE ENGINE
CHECK ENGINE OIL LEVEL (See Fig. 9)
, The engine in your unit has been shipped, from the
factory, already filled with summer weight oil
Check engine oil with unit on level ground.
•Remove dipstick and wipe clean, reinsert the dipstick
and push itat! the way down into the tube, wait for afew
seconds, remove and read oil level. If necessary, add
oil untit "FULL" mark on dipstick is reached. Do not
overfill.
For cold weather operation you should change oil for
easier starting (See "OIL VISCOSITY CHART" in the
Customer Responsibilities section of this manual).
o To change engine oil, see the Customer Responsibili-
ties section in this manual.
ENGINE OIL
FILLER CAP
FiG. 9
ADD GASOL|NE
• Fi!f fuel tank. Use fresh, clean, regular unleaded
gasoline. (Use of leaded gasoline wilt increase carbon
and lead oxide deposits and reduce valve life).
IMPORTANT: WHENOPERAT]NG1NTEMPERATURES
BELOW 32°F(0°C), USE FRESH, CLEAN WINTER GRADE
GASOLINE TO HELP iNSURE GOOD COLD WEATHER
STARTING.
WARNING: Experience indicates that alcohot blended
fuels (called gasoho_ or using ethanot or methanol) can
attract moisture which leads toseparation and formation of
acids during storage. Acidic gas can damage the fuel
system of an engine while in storage. To avoid engine
problems, the fuel system should be emptied before stor-
age of 30 days or longer. Drain the gas tank, start the
engine and let it run until the fuel lines and carburetor are
empty. Use fresh fuel next season. See Storage Instruc-
tions for additional information. Never use engine or
carburetor cleaner products in the fuel tank or permanent
damage may occur,
CAUTION: Fill to bottom of gas tank
filler neck. Do not overfill. Wipe off any
spilled oil or fuel Do not store, spill or
use g_ine near an open flame.
TO START ENGINE (See Fig. 8)
When starting engine for the firsL time or if engine has run
out of fuel, itwitt take extra cranking time to move fuel from
the tank to the engine.
- Depress clutch/brake pedal and set parking brake.
*Place gearshift lever in "NEUTRAL" position,
Move attachment clutch to "DISENGAGED" position.
Pull choke control out to "CHOKE" position for cold
engine start. For warm engine start do not use choke
control.
*Move throttle control to midway between "FAST" and
"SLOW" positions.
Insert key into ignition and turn key clockwise to"START"
position and release key as soon as engine starts. Do
not run starter continuously for more than fifteen sec-
onds per minute, if engine does not start after several
attempts, move throttle control to "FAST" position, wait
a few minutes and try again.
When engine starts, slowly push choke control in.
. Move throttle control to "FAST" position.
Atlow engine to warm up for a few minutes before
engaging drive or attachments.
NOTE: tf at a high altitude (above 3000 feet) or in cold
temperatures (below 32 ° F), the carburetor fuel mixture
may need to be adjusted for best engine performance. See
"TO ADJUST CARBURETOR" in the Service and Adjust-
ments section of this manual.
12

CUSTOM BmL ES
MAINTENANCE SCHEDULE
FILL iN DATES
AS YOU COMPLETE
REGULAR SERVICE SERVICE DATES
Check Brake Operation
Check for Loose Fasteners G##
Sharpen!Replace Mower Blades
Lubrication Chart
Check Battery Level/Recharge
Clean Battery and Terminals
Check Transaxfe Cooling
Adjust Blade Belt(s) Tension
Adjust Motion Drive Belt(s) Tension
Check Engine Oil Level
Change Engine Oil
Clean Air Filter
Clean Air Screen
inspect Muffler/spark Attester
Iv'
V',
v"
v"
v"
v" v"
V'2
V'2i
Replace Oil Filter (If equipped)
Clean Engine Cooling Fins
Replace Spark Plug
Replace Air Filter Paper Cartridge
Replace Fuel Filter
J
V'5
V'5
v"
1 - Change more often when operating under a heavy load or in high ambient temperatureS.
2 - Service more often when operating in dirty ondusty conditions.
JI-
V" .......I-
V"
V" l-
v" v"
v'i B I l_1 _
3 - If equipped with oil filter, change oil every 50 hours,
4 - Replace biades more often when mewing in sandy soil.
GENERAL RECOMMENDATIONS
The warranty on this tractor does not cover items that have
been subjected to operator abuse or negligence. To
receive full value from the warranty, operator must main-
tain tractor as instructed in this manual.
Some adjustments wilt need to be made periodically to
properly maintain your tractor.
All adjustments in the Service and Adjustments section of
this manual should be checked at least once each season.
Once a year you should replace the spark plug, clean
or replace air filter, and check blades and belts for
wear. A new spark plug and clean air filter assure
proper air-fuel mixture and helpyour engine run better
and last longer.
BEFORE EACH USE
Check engine oil level.
,Check brake operation.
Check tire pressure.
o Check for loose fasteners.
IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS
WHICH HAVE SPECIAL NYLON BEARINGS. VISCOUS LUBRI-
CANTS WILL ATTRACT DUST AND DIRT THAT WiLL SHORTEN
THE LIFE OF THE SELF-LUBRICATING BEARINGS, IF YOU
FEEL THEY MUST BE LUBRICATED, USE ONLY A DRY, POW-
DERED GRAPHITE TYPE LUBRICANT SPARINGLY.
5 - fl equipped with adiustable system.
LUBRICATION CHART
(_TIE ROD BALL JOINTS
(_) SPINDLE ZERK
(_) FRONT WHEEL (_)
BEARING ZERK BEARING ZERK
®SECTOR GEAR ENGINE (_)
PLATE
CTRANSAXLE
FLUID
13
(_ SAE 30 NON-DETERGENT OiL (ISO 100)
(_ GENERAL PURPOSE GREASE
(_) REFER TO CUSTOMER RESPONSIBIUTtES "ENGINE" SECTION
(_) SPRAY StMCONE LUBRICANT (MOVE BOOTS TO LUBRICATE)

CUSTOM ILITIES
TRACTOR
Always observe safety rules when performing any mainte-
nance.
BRAKE OPERATION
If tractor requires more than six (6) feet stopping distance
at high speed in highest gear, then brake must be adjusted.
(See "TO ADJUST BRAKE" in the Service and Adjust-
ments section of this manual).
TIRES
° Maintain proper air pressure in all tires (See "PROD-
UCT SPECIFICATIONS" on page 3 of this manual).
Keep tires free of gasoline, oil, or insect control chemi-
cals which can harm rubber.
• Avoid stumps, stones, deep ruts, sharp objects and
other hazards that may cause tire damage.
TRANSAXLE COOUNG
Keep transaxte free from build-up of dirt and chaff which
can restrict cooling_
CHECK TRANSAXLE ORL LEVEL
(See Fig. 10)
Block up rear axle securely or use a tractor jack.
Remove left rear wheel by removing hub bolts.
, Remove filler plug from transaxle. Oil level must be
even with plug threads. If necessary, fill with SAE 30
non-detergent oil (ISO 100). Replace filler plug.
,Reassemble wheel to hub.
• For approximate capacity, see "Product Specifica-
tions" on page 3 of this manual.
TRANSAXLE
OFILLER PLUG
©
BATTERY (See Fig. 11)
Your tractor has a battery charging system which is suffi-
cient for normal use. However, periodic charging of the
battery with an automotive charger will extend it's life.
• Acid solution level in each battery cell should be even
with bottoms of vent wells. Add only distilled or iron free
water if necessary. Do not overfill.
• Keep battery and terminals clean.
-Keep battery bolts tight.
• Keep vent caps tight and small vent holes incaps open.
• Recharge at 6 amperes for 1 hour_
CUT AWAY VIEW
VENT
BATTERY
CELL ACID
LEVEL
FIG. 1t
TO CLEAN BATTERY AND TERMINALS -
Corrosion and dirt on the battery and terminals can cause
the battery to "leak" power.
Remove terminal guard.
*Disconnect BLACK battery cable first then RED battery
cable and remove battery from tractor.
Wash battery with solution of four tablespoons of bak-
ing sodato one gatton of water. Be careful notto getthe
soda solution into the cells.
Rinse the battery with plain water and dry.
Clean terminals and battery cable ends with wire brush
until bright.
Coat termir_als with grease or petroleum jelly.
, Reinstall battery (See "INSTALL BATTERY" in the
Assembly section of this manual).
V- BELTS
check V-Belts for deterioration and wear after 100 hours of
operation. Replace if necessary. The belts are not adjust-
able. Replace belts if they begin to slip from wear.
FIG. 10
14

CUSTOMER FIESPONSIBmLITIES
ENGINE
LUBRICATION
Only use high quality detergent oil rated with API service
classification SG. Select the oil's SAE viscosity grade
according to your expected operating temperature.
SAEVISCOSITYGRADES
°F -20 _ 0o 30_ 32_ 40_ 60 ° 80 _ 100 °
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE
NOTE: Although mu{ti-viscosity oils (5W30, 10W30 etc.)
improve starting in cold weather, these multkviscosity oils
will result in increased oil consumption when used above
32°F. Check your engine oil levet more frequently to avoid
possible engine damage from running low on oil..
Change the oil after the first two hours of operation and
every 50 hours thereafter or at least once a year if the
tractor is not used for 50 hours in one year.
Check the crankcase oi] level before starting the engine
and after each eight (5) hours of continuous use. Tighten
oil fill cap/dipstick securely each time you check the oil
level.
TO CHANGE ENGINE OIL (See Figs. 12 and t3)
Determine temperature range expected before oil change.
All oil must meet API service classification SG.
Be sure tractor is on level surface.
,Oil witl drain more freely when warm.
Catch oil in a suitable container.
• Remove oil filler cap. Be careful not to allow dirt to
enter the engine when changing oil.
Remove drain plug.
After oil has drained completely, replace oil drain plug
and tighten securely.
, Refitl engine with oil through oil filler tube, Pour slowty.
Do not overfill° For approximate capacity see "Product
Specifications" on page 3 of this manua!.
o Use gauge on dipstick for checking level. Be sure
dipstick is in all the way for accurate reading. Keep oit
at "FULL" line on dipstick.
o
FIG. 13
CLEAN AIR SCREEN (See Fig. 14)
Air screen must be kept free of dirt and chaff to prevent
engine damage from overheating. Clean with a wire brush
or compressed air tb remove dirt and stubborn dried gum
fibers.
CLEAN ENGINE COOLING FINS
(See Fig. 14}
Remove any dust, dirt or oil from engine cooling fins to
prevent engine damage from overheating. Engine blower
housing must be removed. Remove side panels and hood
sSee"TO REMOVE HOOD AND GRILL ASSEMBLY" inthe
ervice and Adjustments section of this manual.)
/
COOLING FINS \
UNDER HOUSING AiR SCREEN
(BOTH SIDES)
FiG. 14
ENGINE OIL
FILLER CAP
DIPSTICK
FiG. 12
15

CUSTOMER RESPONSiBiLITIES
AiR FILTER (See Fig. 15)
Your engine will not run properly using a dirty air filter.
Clean the foam pre-cleaner element after every 25 hours of
operation or every season. Service paper cartridge every
!00 hours or every season, whichever occurs first.
Service air cleaner more often under dusty conditions.
*Remove wing nut and cover.
o Remove seal and cartridge plate.
TO SERVICE PRE-CLEANER
Slide foam pre-cleaner off cartridge.
Wash itin liquid detergent and water.
Squeeze it dry in a clean cloth.
- Saturate it in engine oil. Wrap it in clean, absorbent
cloth and squeeze to remove excess oil.
TO SERVICE CARTRIDGE
. Gentry tap the flat side of the paper cartridge to dis-
lodge dirt. Do not wash the paper cartridge or use
pressurized air, as this will damage the cartridge.
Replace a dirty, bent, or damaged cartridge,
. Reinstall the pre-cleaner (cleaned and oiled) over the
paper cartridge,
. Reassemble air cleaner, cartridge plate, and seal.
, Install the air cleaner cover and wing nut. Tighten wing
nut 1/2turn to 1 full turn after nut contacts cover. Do not
overtighten.
ENG1NE OtL FILTER
Replace the engine oil filter every season or every other oil
change if the tractor is used more than 100 hours in one
year.
IN-LINE FUEL FILTER (See Fig. 16)
The fuel fllter should be replaced once each season. Iffuel
filter becomes clogged, obstructing fuel flow to carburetor,
replacement is required.
*With engine cool, remove filter and plug fuel line
sections.
• Place new fuel filter in position in fuel line with arrow
pointing towards carburetor.
• Be sure there are no fuel line leaks and ciamps are
properly positioned,
o Immediately wipe up any spiIled gasoline.
CLAMP _ j CLAMP
COVER WING NUT
CARTRIDGE
PLATE
FOAM
PRE-CLEANER __ SEAL
__ CARTRIDGE
FIG. 16
CLEANING
o Clean engine, battery, seat, finish, etc. of all foreign
matter.
oKeep finished surfaces and wheels free of atl gasoline,
oil, etc.
• Protect painted surfaces with automotive type wax.
We do not recommend using a garden hose to clean your
tractor unless the electrical system, muffler, air filter and
carburetor are covered to keep water out. Water in engine
can result in a shortened engine life.
FIG. 15
MUFFLER
Inspect and replace corroded muffler and spark arrester (if
equipped) as it could create a fire hazard and/or damage.
SPARK PLUGS
Replace spark plugs at the beginning of each mowing
season or after every 100 hours of operation, whichever
comes first. Spark pIug type and gap setting are shown in
"PRODUCT SPECIFICATIONS" on page 3 of this manual.
!6

SERVICE ADJUSTMENTS
CAUTION: BEFORE PERFORMING ANY SERVICE OR ADJUSTtVlENTS:
Depress clutch/brake pedal fully and set parking brake.
_ lace gearshift lever in 'NEUTRAL'position.
Place attachment clutch in "DISENGAGED position,
®Turn ignition key "OFF" and remove key.
Make sure the blades and all moving parts have completely stopped.
*Disconnect spark plug wire from spark plug and place wire where itcannot come in contact with
plug.
POWER TAKE OFF (CLUTCH PULLEY -See
Fig, 17)
The power take-off clutch should provide years of service.
The clutch incorporates a built-in brake that stops the pulley
almost immediately. Eventually, the internalbrake will wear
so the mower blades wilt not stop as recommended.
Adjustments should be made by your nearest authorized
service center.
ss--._. CLUTCH
_Jf_- ....... ':_=._. J PULLEY
FIG, t7
TO ADJUST BRAKE (See Fig. 18)
Your tractor is equipped with an adjustable brake system
which is mounted on the left side of the transaxle,
If tractor requires more than six (6) feet stopping distance
at high speed inhighest gear, then brake must be adjusted.
iMPORTANT: DO NOT OVER TIGHTEN BRAKE, WHEN
DEPRESSING CLUTCH BRAKE PEDAL, THE MOTION
DRIVE BELT MUST STOP MOVING (DECLUTCH FROM
ENGINE PULLEY) BEFORE BRAKE ENGAGES.
IMPROPER ADJUSTMENT WILL CAUSE HARD SHIFTING
AND EXCESSIVE WEAR TO BRAKE LINING.
= Park and turn off the tractor on a level surface. Place
gear shift lever in "N" (neutral) position. Disengage
parking brake and be sure tractor does not roll in either
direction.
Lower mower deck (if installed on tractor).
Snap out access hole cover on left side of tractor above
footrest.
o Loosen jam nut at clevis which will allow brake rod to be
rotated.
With pliers, from underside of frame, unscrew brake
rod from clevis four (4) to six (6) full turns.
o Start tractor with gear shift lever in "N" (neutral) posi-
tion.
Stop engine. Screw brake rod back into clevis until
clevis pin is against rear edge of stot in brake arm. Do
not over tighten (see "IMPORTANT" above).
Tighten jam nut against clevis.
Replace access hole cover.
o Road test tractor for proper stopping distance and
dectutching as stated above. Readjust if necessary, if
proper adjustment cannot be attained, further mainte-
nance is necessary. Contact your nearest authorized
service center,
CLEVIS
PIN _,_,
,
\ JAM NUT _/___._
Ir
r_n_r,_ BRAKE ' '_ :>'
ARM ROD _'_>
FIG. 18
Slowly depress clutch/brake pedal to the point where
the motion drive belt stops moving, Hold clutch/brake
pedal in this position and engage parking brake. If belt
begins to move after engaging parking brake, reset
parking brake by depressing clutch/brake pedal slightly
to next notch on parking brake. 17

SERVICE AND ADJUSTMENTS
TO REPLACE MOTION DRIVE BELT (See
Figs. 19 and 20)
Park the tractor on level surface. Engage parking brake.
Forease of service there is a belt installation guide decal On
bottom side of left footrest. It is not necessary to remove
mower.
BELT REMOVAL -
, Raise hood and disconnect negative ground battery
cable.
Set parking brake (to get belt slack).
Loosen (do not remove) two (2) engine pulley belt
guide bolts and swivel R.H. side of belt guide up.
Tighten L.H. bolt to hold belt guide in position.
o Roll belt off engine pulley.
,Roll belt off "V" idler, flat idler and ciutching idfer
pulleys,
• Roll belt off clutch pulley-between pulley and chassis.
Pull belt off transaxte pulley.
BELT INSTALLATION -
• Push belt down from engine pulley area. Place back
(flat) side of belt on flat idler(flat idler is next to chassis).
•Place belt on clutching idler and over clutch pulley. "V"
(narrow) part of belt should engage clutch pulley.
• Place belt around transaxle pulley. "V" part of belt
should engage transaxle pulley.
•Make sure "V" part of belt engages "V" idter_
-Roll belt over engine pulley.
• Loosen L.H. engine pulley belt guide bolt and swivel
belt guide on to R.H. bolt. Tighten LH, and R.H, bolts
securely.
® Release parking brake,
IMPORTANT: CHECK BRAKE ADJUSTMENT,
LH, BOLT
ENGINE
PULLEY
.BOLT
FroG.19
FLAT iDLER
"'V" iDLER CLUTCH{NG IDLER TRANSAXLE PULLEY
CLUTCH PULLEY
FiG. 20
TO ADJUST STEERING WHEEL ALIGNMENT
If steering wheel crossbars are not horizontal (left to right)
when wheels are positioned straight forward, remove steer-
ing wheel and reassemble per instructions in the Assembly
section of this manual.
FRONT WHEEL TOE4N ADJUSTMENT
Front wheel toeqn is required for proper steering operation.
Toe-in was set at the factory and adjustment should not be
necessary, If parts in the front axle or steering mechanism
have been replaced or damaged, check toe-in and adjust if
necessary.
TO CHECK TOE-IN (See Fig. 21) -
Position front wheels straight ahead.
*Measure distance between wheels at front and rear of
tires (dimensions "A" and "B").
Front dimension "A" should be tt8" to t/4" less than rear
dimension "B".
TO ADJUST TOE-IN (See Figs. 2I and 22) -
It is important that both tie rods be equal in length before
adjusting toe-in. Both tie rods should measure approxi-
mately 10-1/4" in tength (see inset). Adjust if necessary.
, Loosen jam nuts at adjustment sleeves on tie rods.
* Adjust both tie rods equally until dimension "A" is 1/8"
to 1/4" less than dimension "B".
o Tighten jam nuts securely,
B
FRONT OF TRACTOR
A _"
FBG.21
ADJUSTMENT SLEEVES
TIE
ROD
JAM NUTS
FIG. 22
FRONT WHEEL CAMBER
The front wheel camber is not adjustable on your tractor. If
damage has occurred to affect the front wheel camber,
contact your nearest authorized service center.
!8

SERVICE AND ADJUSTMENTS
TO REMOVE WHEEL FOR REPAIRS
FRONT WHEEL (See Fig. 23) -
• Block up axle securely.
o Remove axle cover, retaining ring and washersto allow
wheel removal.
. Repair tire and reassemble.
•Replace washers and snap retaining ring securely in
axle groove.
® Replace axle cover.
WASHERS
RETAINING
RtNG
AXLE COVER
FIG. 23
REAR WHEEL-
BlOCk rear axle securely.
Remove five (5) hub bolts to allow wheel removal.
•Repair tire and reassemble. Replace and tighten hub
bolts and axle cover securely.
TO START ENGINE WITH A WEAK BATTERY
See Figs. 24 and 25)
_. j_ ate e_ses, Keep sparks, flame i
and _eHats away from bat-
ter'_ eye protection
a,oo ba,e,o,. .............................1
If your battery is too weak to start the engine, it should be
recharged, tf "jumper cables" are used for emergency
starting, follow this procedure:
IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A
12 VOLT NEGATIVE GROUNDED SYSTEM, THE OTHER
VEHICLE MUST ALSO BE A t2 VOLT NEGATIVE
GROUNDED SYSTEM. DO NOT USE YOUR TRACTOR
BATTERY TO START OTHER VEHICLES.
TO ATTACH JUMPER CABLES -
• Connect each end of the RED cable to the POSITIVE (+)
terminal of each battery, taking care notto short against
chassis.
Connect one end of the BLACK cable tothe NEGATIVE
(-) terminal of fully charged battery.
Connect the other end of the BLACK cable to a bolt on
the L.H. side of chassis, away from fuel tank and battery.
TO REMOVE CABLES, REVERSE ORDER -
• BLACK cable first from left side of chassis and fully
charged battery.
RED cable last from both batteries.
L.H,PANEL BOLT
O/
FIG. 25
TO REPLACE FUSE
Replace with 30 amp automotive-type plug-in fuse, The
fuse holder is located behind the dash.
TO REPLACE HEADLIGHT BULB
. Raise hood.
= Pull bulb holder out of hole in the backside of the grill.
• Replace bulb in holder and push bulb holder securely
back into the hole in the backside of the grill.
. Close hood.
iNTERLOCKS AND RELAYS
Loose or damaged wiring may cause your tractor to run
poorly, stop running or prevent it from starting.
Check wiring. See the electrical wiring diagram in the
Repair Parts section of this manual.
19

SERVICE A
TO REMOVE HOOD AND GRILL ASSEMBLY
(See Figs. 26 & 27)
• Lift hood. Disconnect headlight wire connection.
oUnscrew one screw at rear of each side panel.
•Pivot hood and side panel forward and lift off tractor.
, To replace, reverse above procedure.
FiG. 26
WiRE
CONNECTION
\
FiG. 27
ENGINE
TO ADJUST THROTTLE CONTROL CABLE
(See Fig. 28)
The throttle control has been preset at the factory and
adjustment should not be necessary. Check adjustment as
described below before loosening cable, if adjustment is
necessary, proceed as follows:
o With engine not running, move throttle control lever to
"FAST" position.
o Check that throttle lever is against high speed stop. If
itis not, loosen clamp screw and pull throttle cable until
lever is against stop. Tighten clamp screw securely.
TO ADJUST CARBURETOR (See Fig. 29)
The carburetor has been present at the factory and adjust-
ment should not be necessary. However, minor adjustment
may be required to compensate for differences in fuel,
temperature, altitude or load. If the carburetor does not
need adjustment, proceed as follows:
in general, turning the adjusting needles in (clockwise)
decreases the supply of fuel to the engine giving a leaner
fuel/air mixture. Turning the adjusting needles out (coun-
terclockwise) increases the supply of fuel to the engine
giving a richer fuet/air mixture.
IMPORTANT: DAMAGE TO THE NEEDLES AND THE
SEATS tN CARBURETOR MAY RESULT IF SCREW IS
TURNED IN TOO TIGHT.
PRELIMINARY SETTING -
• Be sure you have a clean air filter, and the throttle
control cable and choke are adjusted properly (see
above).
ADJUSTMENTS
With engine off turn idle fuel adjusting needle in (clock-
wise) closing it finger tight and then turn out
(counterclockwise) 1-1/4 turns.
* Turn main fuel adjusting needle in (clockwise) closing
finger tight and then turn out (counterclockwise) 1 turn.
FINAL SETTING -
*Start engine and allow to warm for five minutes. Make
final adjustments with engine running and shift/motion
control lever in "NEUTRAL" position.
With throttle control lever in "FAST" position, turn main
fuel adjusting needle in (clockwise) until engine begins
to die then turn out (counterclockwise) until engine
runs rough. Turn needle to a point midway between
those two positions.
Idle speed setting- With throttle control lever in"SLOW"
position, engine should idle at 1400 RPM. If engine
idles too stow or fast, turn idle speed adjusting screw in
or out until correct idle is attained.
- Idle fue! needle setting - With throttle control lever in
"SLOW" position, turn idle fuel adjusting needle in
(clockwise) until engine begins to die and then turn out
(counterclockwise) until engine runs rough. Turn needle
to a point midway between those two positions,
*Recheck idle speed. Readjust if necessary.
ACCELERATION TEST -
- Move throttle control lever from "SLOW" to "FAST"
position. If engine hesitates or dies, turn idle mixture
screw out (counterclockwise) 1/8 turn. Repeat test and
continue to adjust, if necessary, until engine acceler-
ates smoothly.
High speed stop is factory adjusted. Do not adjust-damage
may result.
IMPORTANT: NEVER TAMPER WITH THE ENGINE
GOVERNOR, WHICH IS FACTORY SET FOR PROPER
ENGINE SPEED. QVERSPEEDING THE ENGINE ABOVE
THE FACTORY HIGH SPEED SETTING CAN BE
DANGEROUS. IFYOUTHINKTHE ENGINE-GOVERNED
HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR
NEAREST AUTHORIZED SERVICE CENTER, WHICH HAS
PROPER EQUIPMENT AND EXPERIENCE TO MAKE ANY
NECESSARY ADJUSTMENTS.
THROTTLE THROTTLE
: LEVER SHOWN Z& LEVER SHOWN
{N HIGH SPEED _ q .|N LOW SPEED
POS|TtON _ POSmON
THROTTLE /I _I [_,.,_'/?'_
CABLE
CLAMP /_'___-
SCREW H|GH SPEED STOP
FroG°28
IDLE SPEED iDLE FUEL
SCREW NEEDLE
MAmNFUEL
ADJUSTING
NEEDLE
20 FIG. 29