Craftsman 917.371623 User manual

ROTARY AWN MOWER
625 Series Briggs & Stratton Engine
Power-Propelled
22" Multi-Cut
Model No.
917.371623
•EspaSol, p. 19
CAUTION:
Read and follow all
Safety Rules and Instructions
before operating this equipment
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
Visit our Craftsman website: www, sears,com/craftsman

Warranty .................................................... 2
Safety Rules .......................................... 2-4
Product Specifications .............................. 4
Assembly /Pre-Operation ........................ 6
Operation ............................................. 7-11
Maintenance Schedule ............................ !2
Maintenance ...................................... 12415
Service and Adjustments ................... 15-16
Storage .............................................. 16-17
Troubleshooting ................................. 17-18
Repair Parts ....................................... 36-45
Sears Service .......................... Back Cover
2-YEAR FULL WARRANTY ON CRAFTSMAN LAWN MOWER
If this Craftsman Lawn Mower fails due to manufacturer defects in material or
workmanship within two years from the date of purchase, return it to any Sears store,
Parts & Repair Center or other Craftsman outlet for free repair (or replacement if repair
proves impossible)_
This warranty applies for only 90 days from the date of purchase if this Lawn Mower is
ever used for commercial or rental purposes.
This ,warranty does not cover:
• Expendable items that become worn during normal use, such as rotary mower
blades, blade adapters, belts, air cleaners and spark plug.
• Repairs necessary because of operator abuse or negligence, including bent
crackshafts and the failure to assemble, operate or maintain this Lawn Mower
according to all supplied product instructions_
This warranty applies only while this product is used in the United States,
This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
IMPORTANT: This cutting machine is capable of amputating hands and feet and throw-
ing objects. Failure to observe the following safety instructions could result in serious
injury or death+
_,Look for this symbol to point out impor-
tant safety precautions. It means
CAUTIONI!I BECOME ALERTI!!
YOUR SAFETY IS INVOLVED,
_i, WARNING: In order to prevent ac-
cidental starting when setting up, trans-
porting, adjusting or making repairs,
always disconnect spark plug wire and
place wire where it cannot come in contact
with plug.
_WARNING: Engine exhaust, some of its
constituents, and certain vehicle components
contain or emit chemicals known to the State
of Californiato cause cancer and birth defects
or other reproductive harm.
_t,WARNING: Battery posts, terminals and
related accessories contain lead and Iead
compounds, chemicals known to the State
of California to cause cancer and birth
defects or other reproductive harm, Wash
hands after handling.
_I, CAUTION: Muffler and other engine
parts become extremely hot during
operation and remain hot after engine has
stopped. To avoid severe burns on contact,
stay away from these areas.

I, GENERAL OPERATION
• Read, understand, and follow all
instructions on the machine and in the
manual(s) before starting. Be thoroughly
familiar with the controls and the proper
use of the machine before starting.
• Do not put hands or feet near or under
rotating parts. Keep clear of the dis-
charge opening at all times,
• Only allow responsible individuals, who
are familiar with the instructions, to oper-
ate the machine,
• Clear the area of objects such as rocks,
toys, wire, bones, sticks, etc., which
could be picked up and thrown by blade.
° Be sure the area is clear of other people
before mowing. Stop machine if anyone
enters the area.
• Do not operate the mower when bare-
foot or wearing open sandals. Always
wear substantial foot wear.
• Do not pull mower backwards unless
absolutely necessary, Always look down
and behind before and while moving
backwards_
• Never direct discharged material toward
anyone. Avoid discharging material
against a wall or obstruction. Material
may richochet back toward the opera-
tor, Stop the blade when crossing gravel
surface&
• Do not operate the mower without
proper guards, plates, grass catcher or
other safety protective devices in place.
. See manufacturer's instructions for
proper operation and installation of
accessories. Only use accessories ap-
proved by the manufacturer,
• Stop the blade(s) when crossing gravel
drives, walks, or roads.
• Stop the engine (motor) whenever you
leave the equipment, before cleaning the
mower or unclogging the chute.
• Shut the engine (motor) off and wait until
the blade comes to complete stop before
removing grass catcher.
• Mow only in daylight or good artificial
light.
• Do not operate the machine while under
the influence of alcohol or drugs.
• Never operate machine in wet grass.
Always be sure of your footing: keep a
firm hold on the handle; walk, never run,
• Disengage the self-propelled mech-
anism or drive clutch on mowers so
equipped before starting the engine.
• If the equipment should start to vibrate
abnormally, stop the engine (motor) and
check immediately for the cause. Vibra-
tion is generally a warning of trouble.
• Always wear safety goggles or safety
glasses with side shields when operating
mower,
I1, SLOPE OPERATION
Slopes are a major factor related to slip &
fall accidents which can result in severe in-
jury, All slopes require extra caution. If you
feel uneasy on a slope, do not mow it,
DO:
• Mow across the face of slopes: never
up and down. Exercise extreme caution
when changing direction on slopes.
• Remove obstacles such as rocks, tree
limbs, etc,
• Watch for holes, ruts, or bumps. Tall
grass can hide obstacles.
DO NOT:
• Do not trim near drop-offs, ditches or
embankments. The operator could lose
footing or balance.
• Do not trim excessively steep slopes.
• Do not mow on wet grass. Reduced foot-
ing could cause slipping,
Iii. CHILDREN
Tragic accidents can occur if the operator
is not alert to the presence of children,
Children are often attracted to the machine
and the mowing activity. Never assume
that children will remain where you last
saw them,
• Keep children out of the trimming area
and under the watchful care of another
responsible adult,
• Be alert and turn machine off if children
enter the area.
• Before and while walking backwards,
look behind and down for small children.
• Never allow children to operate the ma-
chine,
. Use extra care when approaching blind
corners, shrubs, trees, or other objects
that may obscure vision,
IV. SAFE HANDLING OF GASOLINE
Use extreme care in handling gasoline.
Gasoline is extremely flammable and the
vapors are explosive.
• Extinguish al! cigarettes, cigars, pipes
and other sources of ignition.
• Use only an approved container.
• Never remove gas cap or add fuel with
the engine running. Allow engine to cool
before refueling°
• Never refuel the machine indoors.
• Never store the machine or fuel contain-
er where there is an open flame, spark
or pilot light such as a water heater or on
other appliances.

• Neverfill containersinsideavehicle,on
atruckortrailerbedwith aplasticliner.
Alwaysplacecontainersontheground
awayfromyourvehiclebeforefilling,
• Removegas-poweredequipmentfrom
thetruckortrailerandrefuelit onthe
ground. Ifthisisnotpossible,then
refuelsuchequipmentwitha portable
container,ratherthanfromagasoline
dispensernozzle.
• Keepthenozzleincontactwiththe rim
ofthefueltankor containeropeningat
alltimesuntilfuelingiscomplete.Do
notusea nozzlelock-opendevice.
. Iffuel is spilledon clothing,change
clothingimmediately°
• Neveroverfillfueltank, Replacegas
capandtightensecurely.
V. GENERAL SERVICE
• Never run a machine inside a closed
area,
• Never make adjustments or repairs with
the engine (motor) running, Disconnect
the spark plug wire, and keep the wire
away from the plug to prevent accidental
starting_
• Keep nuts and bolts, especially blade
attachment bolts, tight and keep equip-
ment in good condition
• Never tamper with safety devices, Check
their proper operation regularly,
• Keep machine free of grass, leaves, or
other debris build-up. Clean oil or fuel
spillage. Allow machine to cool before
storing.
• Stop and inspect the equipment if you
strike an object. Repair, if necessary,
before restarting,
• Never attempt to make wheel height
adjustments while the engine is running.
• Grass catcher components are subject
to wear, damage, and deterioration,
which could expose moving parts or
allow objects to be thrown, Frequently
check components and replace with
manufacturer's recommended parts,
when necessary,
• Mower blades are sharp and can cut,
Wrap the blade(s) or wear gloves, and
use extra caution when servicing them,
° Do not change the engine governor set-
ting or overspeed the engine.
• Maintain or replace safety and instruc-
tion labels, as necessary,
_-WARNING: This lawn mower is equipped with an internal combustion engine and
should not be used on or near any unimproved forest-covered, brush-covered or
grass-covered land unless the engine's exhaust system is equipped with a spark
arrester meeting applicable local or state laws (if any). If a spark arrester is used, it
should be maintained in effective working order by the operator.
in the state of California the above is required by taw (Section 4442 of the California
Public Resources Code), Other states may have similar laws, Federal laws apply on
federal lands, A spark arrester for the muffler is available through your nearest Sears
Parts & Repair Center (See the REPAIR PARTS section of this manual),
Serial Number:
Date of Purchase:
Gasoline Capacity /Type: 1,6 Quads (Unleaded Regular)
Oil Type (API SG-SL): SAE 30 (above 32°F); SAE 5W-30 (below 32°F)
Oil Capacity: 20 Ounces
Spark Plug (Gap: .030") Champion J19LM or RJ19LM
Blade Bolt Torque: 35-40 ft. Ibs.
• The model and serial numbers will be found on a decal on the rear of the lawn mower
housing. Record both serial number and date of purchase in space provided above.
4

Repair Protection Agreements
Congratulations on making a smart pur-
chase° Your new Craftsman® product is
designed and manufactured for years of
dependable operation, But like all prod-
ucts, it may require repair from time to
time, That's when having a Repair Protec-
tion Agreement can save you money and
aggravation.
Purchase a Repair Protection Agreement
now and protect yourself from unexpected
hassle and expense.
Here's what's included in the Agreement:
•Expert service by our 12,000 profe-
sional repair specialists.
. Unlimited service and no charge for
parts and labor on all covered repairs,
• Product replacement if your covered
product can't be fixed.
• Discount of 10% from regular price of
service and service-related parts not
covered by the agreement; also, 10%
off regular price of preventive mainte-
nance check.
•Fast help by phone- phone sup-
port from a Sears representative on
products requiring in-home repair, plus
convenient repair scheduling,
Once you purchase the Agreement, a
simple phone calf is all that it takes for you
to schedule service, You can call anytime
day or night, or schedule a service ap-
pointment online,
Sears has over 12,000 professional repair
specialists, who have access to over 4.5
million quality parts and accessories,
That's the kind of professionalism you can
count on to help prolong the life of your
new purchase for years to come. Purchase
your Repair Protection Agreement today!
Some limitations and exclusions apply.
For prices and additional Information
call 1-800-827-6655.
Sears Installation Service
For Sears professional installation of home
appliances, garage door openers, water
heaters, and other major home items, in
the U.S.A. call 1-800-4-MY-HOME®.
These accessories were available when this lawn mower was produced, They are not
shipped with your mower. They are also available at most Sears retail outlets and
service centers. Some of these accessories may not apply to your lawn mower.
LAWN MOWER PERFORMANCE
CLIPPING
DEFLECTORS
FOR
REAR DISCHARGE
LAWN MOWERS
GRASS CATCHERS
FOR
REAR DISCHARGE
LAWN MOWERS
STABILIZER
LAWN MOWER MAINTENANCE
H,H,,===, = H= ' '
BELTS BLADES
MUFFLERS AIR FILTERS SPARK PLUGS
BLADE ADAPTERS WHEELS ENGINE OIL
GRASS CATCHERS
FOR
SIDE DISCHARGE
LAWN MOWERS

Read these instructions and this manual in its entirety before you attempt to assemble or
operate your new lawn mower.
IMPORTANT: This lawn mower is shipped WITHOUT OIL OR GASOLINE in the engine.
Your new lawn mower has been assembled at the factory with the exception of those parts
left unassembled for shipping purposes. To ensure safe and proper operation of your lawn
mower, all parts and hardware you assemble must be tightened securely° Use the correct
tools as necessary to ensure proper tightness, All parts such as nuts, washers, bolts, etc.,
necessary to complete the assembly have been placed in the parts bag.
TO REMOVE MOWER FROM CARTON
1. Remove Ioose parts included with mower,
2. Cut down two end corners of carton
and lay end panel down flat,
3, Remove all packing materials except
padding between upper and lower
handle and padding holding operator
presence control bar to upper handle.
4, Roll lawn mower out of carton and
check carton thoroughly for additional
loose parts°
HOW TO SET UP YOUR MOWER
TO UNFOLD HANDLE
IMPORTANT: Unfold handle carefully so
as not to pinch or damage control cables.
I, Raise handles until lower handle sec-
tion locks into place in mowing position,
2, Remove protective padding, raise up-
per handle section into place on lower
handle and tighten both handle knobs.
3, Remove handle padding holding operator
presence control bar to upper handle,
Your lawn mower handle can be adjusted
for your mowing comfort° Refer to 'AD-
JUST HANDLE" in the Service and Adjust-
ments section of this manual°
Operator MOWING
POSITION
control bar
• tTJ f
f J
?/./ Upper
UP /,::,;_xx handle
J J X Handle
knob
TO ASSEMBLE GRASS CATCHER
1. Put grass catcher frame into grass bag
with rigid part of bag on the bottom.
Make sure the frame handle is outside
of the bag top,
2. Slip vinyl bindings over frame.
NOTE: If vinyl bindings are too stiff, hold
them in warm water for a few minutes, If
bag gets wet, let it dry before using.
Frame
Vinyl Frame
bindings opening
TO INSTALL ATTACHMENTS
Your lawn mower was shipped ready to be
used as a mutcher_ To convert mower to
bagging or discharging, see "TO CON-
VERT MOWER" in the Operation section
of this manual,
Lower handle
6

KNOW YOUR LAWN MOWER
READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING
YOUR LAWN MOWER. Compare the illustrations with your lawn mower to familiarize
yourself with the location of various controls and adjustments, Save this manual for
future reference.
i 1,1 .............................................................................................i
These symbols may appear on your lawn mower or in literature supplied with the
product. Learn and understand their meaning.
CAUTION ENGINE ENGINE FAST SLOW CHOKE FUEL OIL DANGER, KEEP HANDS
DR WARNING ON OFF AND FEET AWAY
Drive
control
bar Operator presence control bar
Handle knob
Starter
handle Engine oil cap with dipstick
Primer
Grass
catcher Muffler
plug
Air
Mulcher
Housin
cover
Wheel adjuster
(on each wheel)
IMPORTANT: This lawn mower is shipped WITHOUT OIL OR GASOLINE in the engine,
MEETS CPSC SAFETY REQUIREMENTS
Sears rotary walk-behind power lawn mowers conform to the safety standards of the
American National Standards Institute and the U,S, Consumer Product Safety Com-
mission, The blade turns when the engine is running,
Operator presence control bar- must
be held down to the handle to start the
engine, Release to stop the engine_
Starter handle - used for starting engine.
Mulcher door - allows conversion to
discharging or bagging operation, 7
Primer- pumps additional fuel from the
carburetor to the cylinder for use when
starting a cold engine,
Drive control bar - used to engage
power-propelled forward motion of mower°

Theoperationofany
lawnmowercanresult
inforeignobjectsthrown
intotheeyes,whichcan
resultinsevereeye dam-
age,Alwayswearsafetyglassesoreye
shieldswhileoperatingyourlawnmower
orperforminganyadjustmentsorrepairs°
Werecommendastandardsafetyglasses
orwidevisionsafetymaskwornover
spectacles,
HOW TO USE YOUR LAWN MOWER
ENGINE SPEED
The engine speed was set at the factory
for optimum performance, Speed is not
adjustable.
ENGINE ZONE CONTROL
A0_CAUTION: Federal regulations require
an engine control to be installed on this
lawn mower in order to minimize the
risk of blade contact injury, Do not under
any circumstances attempt to defeat the
function of the operator control, The blade
turns when the engine is running.
•Your lawn mower is equipped with an
operator presence control bar which
requires the operator to be positioned
behind the lawn mower handle to start
and operate the lawn mower,
TO OPERATE DRIVE SYSTEM
• To start forward motion, lift drive con-
trol bar up to handle.
• To stop forward motion, release drive
control bar,
IMPORTANT: Always keep drive control
fully engaged against handle when in use_
Operator presence control bar
DRIVE
CONTROL CONTROL
ENGANGED DISENGAGED
TO ADJUST CUTTING HEIGHT
Raise wheels for tow cut and lower wheels
for high cut, adjust cutting height to suit
your requirements° Medium position is
best for most lawns.
•To change cutting height, squeeze ad-
juster lever toward wheel, Move wheel
up or down to suit your requirements. Be
sure all wheels are in the same setting.
NOTE: Adjuster is properly positioned
when plate tab inserts into hole in lever,
Also, 9-position adjusters (if so equipped)
allow lever to be positioned between the
plate tabs.
LEVER BACKWARD Plate tab
TO LOWER MOWER
LEVER FORWARD TO RAISE MOWER Lever
8

TO CONVERT MOWER
Your lawn mower was shipped ready to be
used as a mulcher. To convert to bagging
or discharging:
REAR BAGGING
• Open rear door and remove mutcher
plug. Store mulcher plug in a safe
place,
• You can now install the grass catcher or
optional clipping deflector,
• To convert to mulching or discharging
operation, install mulcher plug into rear
discharge opening of mower,
Discharge deflector
Mulcher plug
SIDE DISCHARGING
• Mulcher plug must be installed into rear
discharge opening of mower,
• Open mulcher door and install dis-
charge deflector under door as shown.
. Mower is now ready for discharging
operation.
• To convert to mulching or bagging
operation, discharge deflector must be
removed and mulcher door closed,
SIMPLE STEPS TO REMEMBER WHEN
CONVERTING YOUR LAWN MOWER
FOR MULCHING -
1, Rear mulcher plug installed,
2_ Mulcher door closed,
FOR REAR BAGGING -
1, Rear mutcher plug removed,
2, Grass catcher installed,
3. Mulcher door closed°
FOR SIDE DISCHARGING -
1, Rear mutcher plug installed,
2. Discharge deflector installed,
A&OAUTION: Do not run your lawn
mower without mulcher plug or approved
grass catcher in place, Never attempt to
operate the lawn mower with the rear door
removed or propped open,
Open mulcher door
9

TO EMPTY GRASS CATCHER
1. Lift up on grass catcher using the
frame handle,
2, Remove grass catcher with clippings
from under lawn mower handle,
3. Empty clippings from bag.
NOTE: Do not drag the bag when empty-
ing; it will cause unnecessary wear,
\ Grass
catcher
frame
handle
BEFORE STARTING ENGINE
ADD OIL
Your lawnmower is shipped without oii in
the engine. For type and grade of oil to
use, see "ENGINE" in the Maintenance
section of this manual.
ACAUTION: DO NOT overfill engine with
oil, or it will smoke heavily from the muffler
on startup,
!. Be sure lawnmower is level.
2, Remove oil dipstick from oil fill spout,
3. You receive a container of oil with the
unit. Slowly pour the entire container
down the oil fill spout into the engine,
NOTE: Initial oil fill requires only I8 ozo
due to residual oil in engine from the
manufacturers 100% quality testing, When
changing oil you may need 20 oz.
4_ Insert and tighten dipstick.
IMPORTANT:
• Check oil level before each use, Add oil
if needed, Fill to full line on dipstick,
• Change the oil after every 25 hours of
operation or each season, You may
need to change the oil more often
under dusty, dirty conditions. See "TO
CHANGE ENGINE OIL' in the Mainte-
nance section of this manual.
Engine
oil cap
Gasoline
filler cap
ADD GASOLINE
• Fill fuel tank to bottom of tank filler neck,
Do not overfill. Use fresh, clean, regular
unleaded gasoline with a minimum of
87 octane, Do not mix oil with gasoline.
Purchase fuel in quantities that can be
used within 30 days to assure fuel fresh-
ness,
A CAUTION: Wipe off any spilled oil or
fuel. Do net store, spill or use gasoline
near an open flame,
ACAUTION: Alcohol blended fuels
(called gasohot or using ethanol or metha-
nol) can attract moisture which leads to
separation and formation of acids during
storage. Acidic gas can damage the fuel
system of an engine while in storage. To
avoid engine problems, the fuel system
should be emptied before storage of 30
days or longer, Empty the gas tank, start
the engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel
next season, See Storage Instructions for
additional information, Never use engine
or carburetor cleaner products in the fuel
tank or permanent damage may occur,
10

TO STOP ENGINE
•To stop engine, release operator pres-
ence control bar,
TO START ENGINE
NOTE: Due to protective coatings on the
engine, a small amount of smoke may be
present during the initial use of the product
and should be considered normal,
1_ To start a cold engine, push primer
three (3) times before trying to start,
Use a firm push, This step is not
usually necessary when starting an
engine which has already run for a few
minutes.
2, Hold operator presence control bar
down to the handle and pull starter
handle quickly, Do not allow starter
rope to snap back,
NOTE: In cooler weather it may be
necessary to repeat priming steps. In
warmer weather over priming may cause
flooding and engine will not start. If you do
flood engine, wait a few minutes before
attempting to start and do not repeat
priming steps.
MOWING TIPS
_, CAUTION: Do not use de-thatcher
blade attachments on your mower. Such
attachments are hazardous, will damage
your mower and could void your warranty,
•Under certain conditions, such as very
tall grass, it may be necessary to raise
the height of cut to reduce pushing
effort and to keep from overloading the
engine and leaving clumps of grass
clippings, It may also be necessary to
reduce ground speed and/or run the
lawn mower over the area a second
time.
• For extremely heavy cutting, reduce the
width of cut by overlapping previously
cut path and mow slowly.
• For better grass bagging and most cut-
ting conditions, the engine speed should
be set in the FAST position,
• Pores in cloth grass catchers can be-
come filled with dirt and dust with use
and catchers will collect less grass. To
prevent this, regularly hose catcher off
with water and let dry before using.
. Keep top of engine around starter clear
and clean of grass clippings and chaff_
This will help engine air flow and extend
engine life,
MULCHING MOWING TIPS
IMPORTANT: For best performance,
keep mower housing free of built-up
grass and trash. See "CLEANING" in the
Maintenance section of this manual,
•The special mulching blade will recut
the grass clippings many times and
reduce them in size so that as they fall
onto the lawn they will disperse into
the grass and not be noticed. Also, the
mulched grass will biodegrade quickly to
provide nutrients for the lawn. Always
mulch with your highest engine (blade)
speed as this will provide the best recut-
ting action of the blades.
• Avoid cutting your lawn when it is wet.
Wet grass tends to form clumps and
interferes with the mulching action. The
best time to mow your lawn is the early
afternoon. At this time the grass has
dried, yet the newly cut area will not be
exposed to direct sunlight,
• For best results, adjust the lawn mower
cutting height so that the lawn mower
cuts off only the top one-third of the
grass blades, tf the lawn is overgrown it
will be necessary to raise the height of
cut to reduce pushing effort and to keep
from overloading the engine and leaving
clumps of mulched grass. For extremely
heavy grass, reduce your width of cut
by overlapping previously cut path and
mow slowly
MAX 1/3
• Certain types of grass and grass
conditions may require that an area be
mulched a second time to completely
hide the clippings, When doing a sec-
ond cut, mow across (perpendicular) to
the first cut path,
•Change your cutting pattern from week
to week_ Mow north to south one week
then change to east to west the next
week. This will help prevent matting and
graining of the lawn.
11

MAINTENANCE
SCHEDULE
Check for Loose Fasteners
,C!e,an,/,Inspect Grass Ca!char
Check Tires
NWCheck Drive Wheels ***
Clean Lawn Mower ....
MClean under Drive Cover ***
OCheck Drive Belt /Pulleys ***
WCheck /Sharpen /Replace Blade
El
RLubrication ..............................
Ciean and Recharge Battery **.................
Eng,neOli,evol
_ hange Engine,Q,}!.......... '.......
Clean Air Filter
,!n,sp,ectMuffler
NReplace Spark Plug
EReplace Ai'r"Ftiier Paper Cartridge
Empty fuel system or add Stabilizer
BEFORE AFTER EVERY EVERY EVERY BEFORE
EACH EACH 10 25 HOURS 100
USE USE HOURS ORSEASON HOURS STORAGE
,,u
v' v'
v' v' v"
v'
v'
v" v'
V'3
v'
v' v_
64,2
_4
v'
* (if so equipped)
** Electric-Start mowers
*** Power-Propelled mowers
**** Use a scraper
to clean under deck
v"
=4 v'
1- Change more often If operating under a heavy load or in htgh outdoor temperatures.
2 - Service more often ff operating in dirty or dusty conditions.
3 - Replace blades more often when mowing In sandy eo]f.
4 * Charge 48 hours at end of season.
5- And after each 5 hours of use
GENERAL RECOMMENDATIONS
The warranty on this lawn mower does not
cover items that have been subjected to
operator abuse or negligence. To receive
full value from the warranty, operator must
maintain unit as instructed in this manual,
Some adjustments will need to be made
periodically to properly maintain your unit°
At least once a season, check to see if
you should make any of the adjustments
described in the Service and Adjustments
section of this manual°
• At least once a year, replace the spark
plug, clean or replace air filter element
and check blade for wear, A new spark
plug and clean/new air filter element
assure proper air-fuel mixture and help
your engine run better and last longer,
• Follow the maintenance schedule in this
manual.
BEFORE EACH USE
• Check engine oil level,
• Check for loose fasteners,
LUBRICATION
Keep unit well lubricated
(See "LUBRICATION CHART").
LUBRICATION CHART
C) Wheel
adjuster (on
each wheel)
Engine oil
Mulcher
door hinge
pin
6) Rear door
hinge
Handle bracket mounting pins
_ Spray lubricant
See "ENGINE" in Maintenance section.
IMPORTANT: Do not oil or grease plastic
wheel bearings. Viscous lubricants will
attract dust and dirtthatwill shorten the life of
the selfqubricating bearings, Ifyou feel they
must be lubricated, use only a dq,; powdered
2graphite type lubricant sparingly,
1

LAWN MOWER
Always observe safety rules when per-
forming any maintenance,
TIRES
• Keep tires free of gasoline, oi!, or insect
control chemicals which can harm rubber.
•Avoid stumps, stones, deep ruts, sharp
objects and other hazards that may
cause tire damage.
DRIVE WHEELS
Check front drive wheels each time before
you mow to be sure they move freely.
The wheels not turning freely means trash,
grass cuttings, etc_are inthe drive wheel area
and must be cleaned to free drive wheels,
If necessary to clean the drive wheels, be
sure to clean both front wheels°
1. Remove hubcaps, Iocknuts & washers.
2. Remove wheels from wheel adjusters.
3. Remove any trash or grass cuttings
from inside the dust cover, pinion and/
or drive wheel gear teeth.
4, Put wheels back in place.
NOTE: If after cleaning, the drive wheels
do not turn freely, contact a Sears or other
qualified service center°
BLADE CARE
For best results, blade must be kept sharp°
eplace a bent or damaged blade.
CAUTION: Use only a replacement blade
approved by the man ufacturer of your mower.
Using a blade not approved by the manu-
facturer of your mower is hazardous, could
damage your mower and void your warrantyo
TO REMOVE BLADE
1. Disconnect spark plug wire from spark
plug and place wire where it cannot
come in contact with plug.
2. Turn lawn mower on its side. Make
sure air filter and carburetor are up.
3, Use a wood block between blade and
mower housing to prevent blade from
turning when removing blade bolt.
NOTE: Protect your hands with gloves
and/or wrap blade with heavy cloth.
4. Remove blade bolt by turning counter-
clockwise.
5 Remove blade & attaching hardware
(bolt, lock washer & hardened washer),
TO REPLACE BLADE
1. Position blade on the blade adapter
aligning the two (2) holes in the blade
with the raised lugs on the adapter.
2 Be sure the trailing edge of blade (oppo-
site sharp edge) is up toward the engine.
3. Install the blade bolt with the lock
washer and hardened washer into
blade adapter and crankshaft.
4_ Use block of wood between blade and
lawn mower housing and tighten the
blade bolt, turning clockwise_
Recommendedtighteningtorque: 35-40ft. lbs,
IMPORTANT: Blade bolt is heat treated°
tf bolt needs replacing, replace only with
approved bolt shown in the Repair Parts
section of this manual.
Blade adapte
Lockwasher
bolt Hardened
washer Trailing edge
TO SHARPEN BLADE
Crankshaft
Crar kshaft
NOTE: We do not recommend sharpening
the blade - but if you do, be sure the blade
is balanced, Care should be taken to keep
the blade balanced, An unbalanced blade will
cause eventual damage to mower or engine,
• The blade can be sharpened with a file
or on a grinding wheel Do not attempt
to sharpen while on the mower,
• To check blade balance, drive a nail into
a beam or wall, Leave about one inch of
the straight nail exposed. Place center
hole of blade over the head of the nail.
If blade is balanced, it should remain in
a horizontal position_ If either end of the
blade moves downward, sharpen the
heavy end until the blade is balanced,
GRASS CATCHER
• The grass catcher may' be hosed with
water, but must be dry when used,
• Check your grass catcher often for dam-
age or deterioration, Through normal
use it will wear. If catcher needs replac-
ing, replace only with approved replace.-
ment catcher shown in the Repair Parts
section of this manual. Give the lawn
mower model number when ordering.
GEAR CASE
• To keep your drive system working
properly, the gear case and area around
the drive should be kept clean and free
of trash build-up. Clean under the drive
cover twice a season.
• The gear case is filled with lubricant to the
proper level at the factory. The only time
the lubricant needs attention is ff service
has been performed on the gear case.
If lubricant is required, use only Texaco
Starplex Premium 1 Grease, Part No,
75036& Do not substitute,13

ENGINE
LUBRICATION
Use only high quality detergent oil rated with
API service classification SG-SL Selectthe
oil's SAE viscosity grade according to your
expected operating temperature°
SAEWSCOS_TYGRADES
F .2o 030 32 _D 6o , .B_ 'm...'_00..j.....
c.;o ._o -1; o lo so =D 4o
TEMPERATURERANGEANTICIP^TEDBEFORENEXTOILCHANG_
NOTE: Although multi-viscosity oils
(5W30, 10W30 etc.) improve starting in
cold weather, these multi-viscosity oils will
result in increased oil consumption when
used above 32°E Check your engine oil
level more frequently to avoid possible
engine damage from running low on oil,
Change the oil after every 25 hours of op-
eration orat least once a year if the mower
is not used for 25 hours in one year.
Check the crankcase oil level before
starting the engine and after each five (5)
hours of continuous use, Tighten oi! plug
securely each time you check the oil level,
TO CHANGE ENGINE OIL
NOTE: Before tipping lawn mower to drain
oil, empty fuel tank by running engine until
fuel tank is empty.
1, Disconnect spark plug wire from spark
plug and place wire where it cannot
come in contact with plug.
2. Remove engine oil cap; lay aside on a
clean surface.
3, Tip lawn mower on its side as shown
and drain oil into a suitable container.
Rock lawn mower back and forth to re-
move any oil trapped inside of engine.
Container
4. Wipe off any spilled oil from lawn
mower or side of engine.
5, Slowly pour oil down the oil fill spout,
stopping every few ounces to check the
oil level with the dipstick.
6. Stop adding oil when you reach the
FULL mark on the dipstick. Wait a
minute to allow oil to settle,
7. Continue adding small amounts of oil,
rechecking the dipstick until oil level
settles at FULL, DO NOT overfill, or
engine will smoke heavity from the
muffler on startup,
8, Afways be sure to retighten oil dipstick
before starting engine_
9. Reconnect spark plug wire to spark plug,
AIR FILTER
Your engine will not run properly and
may be damaged by using a dirty air
filter. Replace the air filter cartridge every
100 hours of operation or every season,
whichever occurs first. Service air cleaner
more often under dusty conditions,
TO CLEAN AIR FtLTER
1. Loosen screw and tilt cover to remove.
2, Carefully remove cartridge_
3, Clean by gently tapping on a flat sur-
face, if very dirty, replace cartridge,
,_CAUTION: Petroleum solvents, such
as kerosene, are not to be used to clean
cartridge_ They may cause deterioration
of the cartridge, Do not oil cartridge_ Do
not use pressurized air to clean or dry
cartridge,
4. install cartridge, then replace cover
making sure the tabs are aligned with
the slots in the back plate. Fasten
screw securely, Back plate
j
C Slot
Cover
Co r tab
MUFFLER
Inspect and replace corroded muffler as it
could create a fire hazard and/or damage°
SPARK PLUG
Replace spark plug at the beginning of
each mowing season or after every 100
hours of operation, whichever occurs
first. Spark plug type and gap setting
are shown in the "PRODUCT SPECiFIC-
ATIONS" section of this manual.
CLEANING
IMPORTANT: For best performance,
keep mower housing free of built-grass
and trash_ Clean the underside of your
14 mower after each use,

_CAUTION: Disconnectsparkplugwire
fromsparkplugandplacewirewhereit
cannotcomein contactwith plug,
• Cleantheundersideofyour lawnmower
byscrapingto removebuild-upofgrass
andtrash.
• Cleanengineoftento keeptrashfrom
accumulating.A cloggedengineruns
hotterandshortensenginelife,
• Keepfinishedsurfacesandwheelsfree
ofallgasoline,oil,etc.
• Wedo notrecommendusinga garden
hosetocleanlawnmowerunlessthe
electricalsystem,muffler,airfilterand
carburetorare coveredto keepwater
out_Waterin enginecan resultinshort-
enedenginelife.
CLEAN UNDER DRIVE COVER
Clean under drive cover at teast twice a sea-
son, Scrape underside of cover with putty
knife or similar tool to remove any build-up
of trash or grass on underside of drive cover.
WARNING: To avoid serious injury, before performing any service and adjustments:
I. Release control bar and stop engine.
2, Make sure the blade and all moving parts have completely stopped°
3, Disconnect spark plug wire from spark plug and place wire where it cannot come in
contact with plug.
LAWN MOWER
TO ADJUST CUTTING HEIGHT
See "TO ADJUST CUTTING HEIGHT" in
the Operation section of this manual.
REAR DEFLECTOR
The rear deflector, attached between the
rear wheels of your mower, is provided to
minimize the possibility that objects will
be thrown out of the rear of the mower
into the operator mowing position, if the
deflector becomes damaged, it should be
replaced.
TO REMOVE DRIVE BELT
1. Remove drive cover.
2o Remove belt from gearcase pulley by
pushing clown on arm and rolling belt
off pulley.
3. Turn lawn mower on its side with air
filter and carburetor down.
4. Remove blade, engine pulley and
debris shield,
5, Remove engine pulley and belt from
debris shield.
TO REPLACE DRIVE BELT
1. Place new drive belt in engine pulley
and belt retainer of debris shield.
2 Route the other end of the new drive
belt through hole in housing
3, Reinstall debris shield.
4. Reinstall blade.
5, Return mower to upright position.
6, Push down on arm, install new belt on
gearcase pulley Release arm slowly.
NOTE: Always use factory approved belt
to assure proper fit and long life,
7. Reinstall drive cover.
Engine pulley
Drive belt
Belt
retainer
PUSH
DOWN _
Drive
cover
Debris shield
.
3,
15
TO ADJUST HANDLE
The handle can be mounted in a high or
low position. The mounting holes in the
bottom of lower handle are off center for
raising or lowering the handle-
1, Remove upper handle and wire tie(s)
securing cable(s) to lower handle.
Remove hairpin cotters from lower
handle bracket mounting pin.
Squeeze lower handle in to remove it
from mounting pin&

4. Turnlowerhandleoverto raiseor
lowerhandle,
5. Squeezelowerhandleinandpositionhofes
onto mountingpinson handlebracket.
6. Reassembleupperhandleandall
partsremovedfromlowerhandle.
Mowing _Mowing .
position _ o. position /_
I I (_ "_ ,1" I 1
" _ //
I I 1 /
Itl t
cott;r--'-_ _z_ _ "_ Hand,e _ _' "_
Mounting" _ bracket
pin LOW POSITION HIGH POSITION
Lower
handl_
ROTATE
ENGINE
ENGINE SPEED
Your engine speed has been factory set.
Do not attempt to increase engine speed
or it may result in personal injury. If you
believe that engine is running too fast or
too slow, take your mower to a Sears or
other qualified service center for repair
and adjustment
CARBURETOR
Your carburetor is not adjustable, If your
engine does not operate properly dueto sus-
pected carburetor problems, take your lawn
mower to a Sears or other qualified service
center for repair and/or adjustment.
IMPORTANT: Never tamper with the
engine governor, which is factory set
for proper engine speed, Overspeeding
the engine above the factory high speed
setting can be dangerous. If you think
the engine-governed high speed needs
g, contact a Sears or other
which has proper
to make any
adjustments.
Immediately prepare your lawn mower for storage at the end of the season or if the unit
will not be used for 30 days or more.
LAWN MOWER
When lawn mower is to be stored for a
period of time, clean it thoroughly, remove
all dirt, grease, leaves, etc. Store in a
clean, dry area,
1. Clean entire lawn mower (See
"CLEANING" in the Maintenance sec-
tion of this manual).
2. Lubricate as shown in the Maintenance
section of this manual.
& Be sure that all nuts, bolts, screws, and
pins are securely fastened. Inspect
moving parts for damage, breakage
and wear_ Replace if necessary_
4. Touch up all rusted or chipped paint
surfaces; sand lightly before painting.
HANDLE
You can fold your mower handle for storage_
1. Squeeze the bottom ends of the lower
handle toward each other until the
lower handle clears the handle bracket,
then move handle forward.
2. Loosen upper handle mounting bolts
enough to allow upper handle to be
folded back,
IMPORTANT: When folding the handle
for storage or transportation, be sure to
fold the handle as shown or you may dam-
age the control cables. 16
,When setting up your handle from the
storage position, the lower handle will
automatically lock into mowing position.
SQUEEZE
TO FOLD
Lower handle '-"-'-
Operator
control bar
FOLD
FORWARD
FOR
STORAGE
\
Lower handle

ENGINE
FUEL SYSTEM
IMPORTANT: tt is important to prevent
gum deposits from forming in essential fuel
system parts such as carburetor, fuel filter,
fuel hose, or tank during storage° Alcohol
blended fuels (called gasohol or using
ethanol or methanol) can attract moisture
which leads to separation and formation
of acids during storage. Acidic gas can
damage the fuel system of an engine while
in storage.
•Empty the fuel tank by starting the en-
gine and letting it run until the fuel lines
and carburetor are empty.
•Never use engine or carburetor cleaner
products in the fuel tank or permanent
damage may occur.
• Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable al-
ternative in minimizing the formation of fuel
gum deposits during storage, Add stabilizer
to gasoline in fuel tank or storage container.
Always follow the mix ratio found on stabilizer
container. Run engine at least 10 minutes
after adding stabilizer to allow the stabilizer to
reach the carburetor. Do not empty the gas
tank and carburetor if using fuel stabilizer.
ENGINE OIL
Drain oil (with engine warm) and replace
with clean engine oil. (See "ENGINE" in
the Maintenance section of this manual).
CYLINDER
1. Remove spark plug.
2. Pour one ounce (29 ml) of oil through
spark plug hole into cylinder.
& Pull starter handle slowly a few times
to distribute oil.
4. Replace with new spark plug.
OTHER
• Do not store gasoline from one season
to another.
• Replace your gasoline can if your can
starts to rust. Rust and/or dirt in your
gasoline will cause problems.
• If possible, store your unit indoors and
cover it to protect it from dust and dirt.
• Cover your unit with a suitable protec-
tive cover that does not retain moisture.
Do not use plastic. Plastic cannot
breathe, which allows condensation to
form and will cause your unit to rusL
IMPORTANT: Never cover mower while
engine and exhaust areas are still warm_
_glbCAUTION: Never store the lawn
mower with gasoline in the tank inside a
building where fumes may reach an open
flame or spark. Allow the engine to cool
before storing in any enclosure-
TROUBLESHOOTING -See appropriate section in manual unless directed
to a Sears Parts &Repair Center.
PROBLEM CAUSE
Does not start 1. Dirty air filter.
2. Out of fuel.
& Stale fuel.
4. Water in fuel.
5. Spark plug wire is
disconnecte&
6. Bad spark plug.
7_ Loose blade or broken
blade adapter.
8. Control bar in released
position.
9. Control bar defective.
1O.Fuel valve lever (if so
equipped) in OFF position.
t 1. Weak battery (if equipped)_
12. Disconnected battery
connector (if equipped).
CORRECTION
1. Clean/replace air filter,
2. Fill fuel tank.
3, Empty fuel tank and refill tank
with fresh, clean gasoline.
4. Empty fuel tank and refill tank
with fresh, clean gasoline_
5. Connect wire to plug,
6. Replace spark plug.
7. Tighten blade bolt or
replace blade adapter.
8. Depress control bar to
handle.
9. Replace control bar.
1&Turn fuel valve lever
to the ON position_
11, Charge battery.
12. Connect battery to engine,
17

TROUBLESHOOTING -See appropriate section in manual unless directed
to aSears Parts &Repair Center.
PROBLEM CAUSE CORRECT,ON
Loss of power 1, Rear of mower housing or 1, Raise cutting height.
blade dragging in grass,
2, Cutting too much grass, i2o Raise cutting heighL
3, Dirty air filter° i3o Clean/replace air filter,
4. Buildup of grass, leaves, 4 Clean underside of mower
and trash under mower, housing.
5, Too much oil in engine, 5. Check oil level.
6, Walking speed too fast, 8. Cut at slower walking speed,
Poor cut _- 1, Worn, bent or loose blade. 1. Replace blade_ Tighten
uneven blade bolt,
2, Wheel heights uneven. 2. Set all wheels at same
height.
& Buildup of grass, leaves 3. Clean underside of
and trash under mower, mower housing,
Excessive 1, Worn, bent or loose blade, 1, Replace blade. Tighten
vibration blade bolt.
2. Bent engine crankshaft, 2, Contact a Sears or other
qualified service center.
iStarter rope 1. Engine flywheel brake is on 1, Depress control bar to
lhard to pull when control bar is released, upper handle before
_i pulling the starter rop e,
2, Bent engine crankshaft, Contact a Sears or other
qualified service center.
3, Blade adapter broken, Replace blade adapter,
4, Blade dragging in grass, i4. Move lawn mower to cut
grass or to hard surface,
Grass catcher I. Cutting height too low, 1, Raise cutting height_
not filling 2,, Lift on blade worn off, _ Replace blade,
(If so equipped) & Catcher not venting air, i Clean grass catcher.
Hard to push !1, Grass is too high or wheel _1o Raise cutting height,
height is too tow,
2. Rear of mower housing or 2. Raise rear of mower housing
blade dragging in grass, one (1) setting higher,
& Grass catcher too full, [3, Empty grass catcher°
i4. Handle height position not _4, Adjust handle height to suit,
right for you.
Loss of drive 1, Belt wear. 1, Check!replace drive belt,
or slowing of 2, Belt off of pulley. 20 Check!reinstall drive belt.
drive speed 3o Drive cable worn or broken, 3o Replace drive cable,
4, "Loose" drive control system. 4o Adjust drive control,
NEED MORE HELP?
You'll find the answer and more on managemyhome.com -,-for free!
• Find this and all your other product manuals online_
• Get answers from our team of home experts.
.Get a personalized maintenance plan for your home,
• Find information and tools to help with home projects,
ihome brought to you by Sears
manage 18

Garant_a......................................................... 19
Reglas de Seguridad ................................. 19-21
Especificaciones del Producto ....................... 2!
Montaje /Pre-Operaci6n ............................... 23
Operaci6n .................................................. 24-27
Mantenimiento ........................................... 29-32
Programa de Mantenimiento ........................ 29
Servicio y Adjustes ................................... 32-33
Almacenamiento ....................................... 33-34
Identificaci6n de problemas .................... 34-35
Partes de repuesto .................................. 36-45
Servtcio Sears .................................. Contratapa
GARANTiA TOTAL DE LA CORTADORA DE C_SPED CRAFTSMAN POR 2 ANOS
Siesta Segadora Craftsman liega a presentar alg_n desperfecto por defectos de materiales
o fabricaci6n durante un plazo de dos afios a partir de la fecha de compra, II_vela de vuelta a
cualquiera de los tiendas Sears, al Centro de Repuestos y Reparaci6n, o a otro comercIo donde se
vendan los equipos Craftsman, a efectos de que se la reparen sin costo (o bien se la reemplacen,
en caso que no sea posible repararla).
Siesta Segadora Ilega a ser utilizada con fines comerciales o arrendada, la presente garantta tendr&
vigencia por s61o90 d[as a partir de la fecha de compra.
La presente garantia no cubre:
•Aquellas piezas fungibles que se desgastan por el uso normal, tales como las cuchtllas rotatorias
de la cortadora, los adaptadores de los cuchillas, los correas, los filtros de aire y los bujias.
• Aqueilas reparaciones que haya que hacer debido ama! uso o negligencia por parte del operador,
inclutdosel &rbot del cigL_er_attorcido u omisiones relativas al armado, manejo o mantenimleno de
la Segadora en un todo de acuerdo a las instrucciones provistas con e! equipo.
La presente garantia se aplicar& solamente en tanto el articulo sea usado en los Estados Unidos.
Esta garant[a le otorga austed derechos legaies especificos; puede que usted tonga, adem&s, otros
derechos, los cuales varfan de estado a estado.
Sears, Roebuck and Co,, Hoffman Estates, IL 60179
IMPORTANTE: Esta maquina cortadaora es capaz de amputar los manos y los manos y los pies y
de lanzar objetos. Si no se observan las instrucciones de seguridad siguientes se pueden producir
lesiones graves o la muerte.
_kBusque este simbolo que sefiala tas precau-
clones de seguridad de importancia. Quiere
decir - tIIATENCtONII! t[[ESTE ALERTOIII
SU SEGURIDAD ESTA COMPROMET1DA
_ADVERTENCIA: Siempre desconecte ei
alambre de la bujia y p6ngaio donde no pueda
entrar en contacto con la buj[a, para evitar el
arranque por accidente, durante la preparaci6n,
el transporte, el ajuste o cuando se hacen
reparaciones.
_ADVERTENCIA: Los bornes, terminales y
accesodos reiativos de la bateda contienen
plomo o ccmpuestos de plomo, productos
qulmicos conocidos en et Estado de Catifornia
como causa de c&ncer y defectos al nacimiento
u otros dar_osreproductivos. Lavar las manos
despu_s de manipularlos,
_PRECAUCl6N: El tubo de escape del motor,
algunos de sus constituyentes y aigunos com-
ponentes del vehiculo contienen o desprenden
productos quimicos conocidos en el Estado de
California como causa de c&ncer y defectos al
nacimiento u otros dafios reproductivos,
19
_PRECAUCl6N: El silenciador y otras piezas
del motor Ilegan a sre extremadamente calien-
tes durante la operaci6n y siguen siendo caii-
entes despu6s de que et motor haya paradoo
Para evitar quemaduras severas, permanezca
lejos de estas &reas.

i. OPERACION
• Antes de empezar, debe familiarizarse
completamente con los controles y el use
correcto de la maquin& Para esto, debe leer
y comprender todas las instrucciones qua
aparecen en la maquina yen los manuales
de operaci6n.
• No ponga las manes o los pies cerca o
debajo de las partes rotatorias, Mant_ngase
siempre lejos de la abertura de la descarga.
• Permita que solamente las personas re-
sponsables que est6n familiafizadas con las
instrucciones operen la m_.quina.
• Despeje el Area de objetos tales come pie-
dras, juguetes, atambres, huesos, palos, etco
que pueden ser recogidos y lanzados per las
cuchillas.
• Aseg_rese qua el Area no se hallen per-
sonas, antes de segaroPare la m&quina si
alguien entra en el Area,
• No opera la maquina sin zapatos o con
sandalias abiertaso P6ngase siempre zapatos
s61idos,
• No tire de la segadora hacia arras a manes
qua sea absolutamente necesado, Mire
siempre hacia abajo y hacia detr&s antes y
mlentras qua se mueve hacia atrAs,
• Nunca dirigir el material descargado hacia
las personas. Evitar descargar material
centre paredes o barreras. El material puede
retornar al eperador_ Pare la cuchilla cuando
se pasa per superficies de gravao
• No opere la segadora sin los respectivos
resguardos, las places, el recogedor de
c_sped u otros aditamentos dise ades para
su protecci6n y seguridad.
•Refi_rase alas instrucciones del fabricante
pare el funcionamiento e instalaci6n de
accesorios, Use _nicamente accesorios
aprobados per el fabricante,.
•Detenga la cuchilla o las cuchillas cuando
cruce per calzadas, calles o caminos de
grave.
• Parer el motor cada vez qua se abandona el
aparato, antes de limpiar la segadora o de
remover residues del tube,
• Apagar el motor y esperar haste que las
cuchtllas est#n completamente parades
antes de remover el receptor de hierba.
•Sager solamente con luz del dia o con una
buena luz artificia!,
• No opera la mAquina bajo ]a influencia del
alcohol o de las drogas,
• Nunca opera ta maquina cuando [a hierba
est_ mojadao Aseg_rese siempre de tener
buena tracciSn en sus p_es; mantenga el
mango firmemente y camine; nunca corrao
• Desconectar el mecanismo de propulsiSn
autSnoma o el embrague de transm}siSn en
las segadoras que Io tienen antes de poner
en marcha el motor,
• Si el equipo empezara a vibrar de una
manera anormal, pare el motor y revise de
inmediato para avedguar la causa_ General-
mente ta vibraciSn suele indicar que existe
alguna averia.
• Siempre use gafas de seguridad o anteojos
con protecciSn lateral cuando opera la sega-
dora.
Ih OPERACION SOBRE LAS CUESTAS
Los accidentes ocurren con m&s frecuencia en
las cuestas_ Estos accidentes ocurren debido a
resba[adas o caidas, las cuales pueden resultar
en graves les}ones.Operar la recortadora en
cuestas requiere mayor concentraci6n, Si se
siente inseguro en una cuesta, no la recorte,,
HACER:
• Puede recortar a tray, s de la superficie de
la cuesta, nunca hacia arriba y hacia abajo.
Precede con extreme precauci6n cuando
cambie de direcci6n en las cuestas,
•Renueva todos los objetos extrar_os, tales
come guijarros, ramas, etc,
.Debe prestar atenciSn a hoyos, baches o
protuberancias_ Recuerde que la hierba alta
puede esconder obstAculos.
NO HACER:
• No recorte cerca de pendientes, zanjas o
terraplenes. El operador puede perder la
tracctSn en los pies o et equilibrio,
• No recorte cuestas demasiado inclinadas_
• No recorte en hierba mojad& La reducciSn
en la tracciSn de la pisada puede causer
resbatones.
llh NIl(lOS
Se pueden producir accidentes trAgicos si el
operador no presta atenciSn ala presencia
de los nifios, A menudo, los niSos se sienten
atraidos per la mAquina y per la actividad de
la siega_ Nunca suponga que los nir3osvan a
permanecer en et mismo lugar donde los vie
per Qttima vez.
• Mantenga a los nifos alejados det Area de
la siege y bajo el cuidado estricto de otra
persona adulta responsable.
• Est_ alerta y apague la mAquina si hay nifios
que entran al Area,
• Antes y cuando este retrocediendo, mire
hacia atrAs y hacia abajo para verificar si hay
ni5os pequefos.
• Nunca permita que los niSos operen la mR-
quina.
• Tenga un cuidado extra cuando se acerque
a esquinas donde no hay visibilidad, a los
arbustos, &rboles u otros objetos qua pueden
interferir con su llnea de visi6n.
IV, MANEJO SEGURO DE GASOLINA
User mucha atenciSn cuando se maneja gaso-
line. La gasoline es extremamente inflamable y
los vapores son explosivoso
• Apagar todos los cigarritlos, cigarros, pipes y
otras fuentes de ignici6n.
• User solo un contenedor apropiado,
• Nunca quitar el tap6n de la gasoline o aSadir
carburante con et motor en marcha. Esperar
qua el motor se enfrfe antes de repostar la
gasoline.
2O