Craftsman 917.378772 User manual

Owner's Manual
ICR.FTSM.Wl
ROTARY LAWN MOWER
7.0 Horsepower
Power-Propelled
21" Rear Discharge
Model No.
917.378772
CAUTION:
Read and followall
Safety Rules and Instructions
beforeoperatingthis equipment
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
Visit our Craftsman website.'www.sears.eorn/eraftsman

Warranty ................................................ 2
Safety Rules ....................................... 2-4
Assembly /Pre-Operation ..................... 5
Operation ............................................ 6-9
Maintenance Schedule ........................ 10
Maintenance ................................... 10-13
Product Specifications ....................... 11
Service and Adjustments ................ 13-14
Storage ........................................... 15-16
Troubleshooting .............................. 16-17
Repair Parts .................................... 35-43
Sears Service ........................ Back Cover
LIMITED TWO YEAR WARRANTY ON CRAFTSMAN POWER MOWER
For two years from date of purchase, when this Craftsman Lawn Mower is maintained,
lubricated, and tuned up according to the operating and maintenance instructions in the
owner's manual, Sears will repair free of charge any defect in material or workmanship.
If this Craftsman Lawn Mower is used for commercial or rental purposes, this warranty
applies for only 90 days from the date of purchase.
This Warranty does not cover:
• Expendable items which become worn during normal use, such as rotary mower
blades, blade adapters, belts, air cleaners and spark plug.
• Repairs necessary because of operator abuse or negligence, including bent crank-
shafts and the failure to maintain the equipment according to the instructions con-
tained in the owner's manual.
Warranty service is available by returning the Craftsman power mower to the nearest
Sears Service Center/Department in the United States. This warranty applies only while
this product is used in the United States.
This Warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
Sears, Roebuck and Co., D/817 WA, Hoffman Estates, Illinois 60179
IMPORTANT: This cutting machine is capable of amputating hands and feet and throw-
ing objects. Failure to observe the following safety instructions could result in serious
injury or death.
_Look for this symbol to point out
important safety precautions. It means
CAUTION!!! BECOME ALERT!!! YOUR
SAFETY IS INVOLVED.
_, CAUTION: Always disconnect spark
plug wire and place wire where it cannot
contact spark plug in order to prevent
accidental starting when setting up,
transporting, adjusting or making repairs.
_,WARNING: Engine exhaust, some of its
constituents, and certain vehicle compo-
nents contain or emit chemicals known
to the State of California to cause cancer
and birth defects or other reproductive
harm. 2
AWARNING: Battery posts, terminals and
related accessories contain lead and lead
compounds, chemicals known to the State
of California to cause cancer and birth
defects or other reproductive harm. Wash
hands after handling.
_, CAUTION: Muffler and other engine
parts become extremely hot during
operation and remain hot after engine has
stopped. To avoid severe burns on contact,
stay away from these areas.

I.GENERAL OPERATION
•Read, understand, and follow all
instructions on the machine and in the
manual(s) before starting, Be thoroughly
familiar with the controls and the proper
use of the machine before starting.
• Do not put hands or feet near or under
rotating parts. Keep clear of the dis-
charge opening at all times.
•Only allow responsible individuals, who
are familiar with the instructions, to
operate the machine.
• Clear the area of objects such as
rocks, toys, wire, bones, sticks, etc.,
which could be picked up and thrown by
the blade.
• Be sure the area is clear of other people
before mowing. Stop machine if anyone
enters the area.
• Do not operate the mower when bare-
foot or wearing open sandals. Always
wear substantial foot wear.
• Do not pull mower backwards unless
absolutely necessary. Always look down
and behind before and while moving
backwards.
• Do not operate the mower without
proper guards, plates, grass catcher or
other safety protective devices in place.
•See manufacturer's instructions for
proper operation and installation of
accessories. Only use accessories ap-
proved by the manufacturer.
• Stop the blade(s) when crossing gravel
drives, walks, or roads.
• Stop the engine (motor) whenever you
leave the equipment, before cleaning
the mower or unclogging the chute.
• Shut the engine (motor) off and wait
until the blade comes to complete stop
before removing grass catcher,
• Mow only in daylight or good artificial
light.
• Do not operate the machine while under
the influence of alcohol or drugs.
• Never operate machine in wet grass.
Always be sure of your footing:keep a
firm hold on the handle and walk; never
run.
•Disengage the self-propelled mech-
anism or drive clutch on mowers so
equipped before starting the engine
(motor).
•If the equipment should start to vibrate
abnormally, stop the engine (motor) and
check immediately for the cause. Vibra-
tion is generally a warning of trouble.
• Always wear safety goggles or safety
glasses with side shields when oper-
ating mower.
U. SLOPE OPERATION
Slopes are a major factor related to slip
and fall accidents which can result in
severe injury. All slopes require extra cau-
tion. If you feel uneasy on a slope, do not
mow it.
DO:
• Mow across the face of slopes: never
up and down. Exercise extreme caution
when changing direction on slopes.
• Remove obstacles such as rocks, tree
limbs, etc.
• Watch for holes, ruts, or bumps.Tal_
grass can hide obstacles.
DO NOT:
• Do not trim near drop-offs, ditches or
embankments. The operator could lose
footing or balance.
• Do not trim excessively steep slopes.
• Do not mow on wet grass. Reduced
footing could cause slipping.
III. CHILDREN
Tragic accidents can occur if the operator
is not alert to the presence of children.
Children are often attracted to the ma-
chine and the mowing activity. Never as-
sume that children will remain where you
last saw them.
• Keep children out of the tdmming area
and under the watchful care of another
responsible adult.
• Be alert and turn machine off if children
enter the area.
•Before and whi_ewalking backwards,
look behind and down for small children.
• Never allow children to operate the
machine.
• Use extra care when approaching blind
corners, shrubs, trees, or other objects
that may obscure vision.
IV. SERVICE
•Use extra care in handling gasoline and
other fuels. They are flammable and
vapors are explosive.
-Use only an approved container.
- Never remove gas cap or add fuel
with the engine running. Allow
engine to cool be{ore refueling. Do
not smoke.
- Never refuel the machine indoors.
- Never store the machine or fuel
container inside where there is an
open flame, such as a water heater.
3

• Never run a machine inside a closed
area.
•Never make adjustments or repairs with
the engine (motor) running. Disconnect
the spark plug wire, and keep the wire
away from the plug to prevent accidental
starting.
• Keep nuts and bolts, especially blade
attachment bolts, tight and keep equip-
ment in good condition.
• Never tamper with safety devices. Check
their proper operation regularly.
• Keep machine free of grass, leaves, or
other debris build-up. Clean oil or fuel
spillage. Allow machine to cool before
storing.
• Stop and inspect the equipment if you
strike an object. Repair, if necessary,
before restarting.
• Never attempt to make wheel height
adjustments while the engine (motor) is
running.
• Grass catcher components are subject
to wear, damage, and deterioration,
which could expose moving parts or
allow objects to be thrown. Frequently
check components and replace with
manufacturer's recommended parts,
when necessary.
• Mower blades are sharp and can cut.
Wrap the blade(s) or wear gloves, and
use extra caution when servicing them.
• Do not change the engine governor set-
ting or overspeed the engine.
These accessories were available when this lawn mower was produced. They are not
shipped with your mower. They are also available at most Sears retail outlets and ser-
vice centers. Most Sears stores can also order repair parts for you, when you provide
the model number of your lawn mower. Some of these accessories may not apply to
your lawn mower.
LAWN MOWER PERFORMANCE
CLIPPING
DEFLECTORS
FOR
REAR DISCHARGE
LAWN MOWERS
GRASS CATCHERS
FOR
REAR DISCHARGE
I.AWN MOWERS
STABILIZER
GRASSCATCHERS
FOR
ISIDEDISCHARGE
LAWNMOWERS
LAWN MOWER MAINTENANCE
MUFFLERS
BLADES
AIR RLTERS
U_.OE AOAP'rERS _n.4_-_
SPARK PLUGS
ENGINEOIL
4

Read these instructions and this manual in
its entirety before you attempt to assemble
or operate your new lawn mower.
IMPORTANT: This lawn mower is shipped
WITHOUT OiL OR GASOLINE in the
engine.
Your new lawn mower has been assem-
bled at the factory with the exception of
those parts left unassembled for shipping
purposes. All parts such as nuts, washers,
bolts, etc., necessary to complete the as-
sembly have been placed in the parts bag.
To ensure safe and proper operation of
your lawn mower, all parts and hardware
you assemble must be tightened securely.
Use the correct tools as necessary to
ensure proper tightness.
TO REMOVE LAWN MOWER FROM
CARTON
1. Remove loose parts included with
mower.
2. Cut down two end corners of carton
and lay end panel down flat.
3. Remove all packing materials except
padding between upper and lower
handle and padding holdingoperator
presence control bar to upper handle.
4. Roll lawn mower out of carton and
check carton thorougly for additional
loose parts.
HOW TO SET UP YOUR LAWN
MOWER
TO UNFOLD HANDLE
IMPORTANT: Unfold handle carefully so
as not to pinch or damage control cables.
1. Raise handles until lower handle sec-
tion locks into place in mowing position.
2. Remove protective padding, raise up-
per handle section into place on lower
handle and tighten both handle knobs.
3. Remove handle padding holding
operator presence control bar to upper
handle.
Your lawn mower handle can be adjusted
for your mowing comfort. Refer to "AD-
JUST HANDLE" in the Service and Adjust-
ments section of this manual.
Operator presence
control bar
LIFT
UI
Mowing
position
Lower handle
TO ASSEMBLE GRASS CATCHER
1, Put grass catcher frame into grass bag
with rigid part of bag on the bottom.
Make sure the frame handle is outside
of the bag top.
2. Slip vinyl bindings over frame.
NOTE: If vinyl bindings are too stiff, hold
them in warm water for a few minutes. If
bag gets wet, let it dry before using.
Catcher
frame
handle
Frame
opening
TO INSTALL ATTACHMENTS
Your lawn mower was shipped ready to
be used as a mulcher. To convert to bag-
ging, see "TO CONVERT MOWER" in the
Operation section of this manual).
5

KNOW YOUR LAWN MOWER
READTHISOWNER'S MANUALAND ALL SAFETY RULES BEFOREOPERATING
YOUR LAWN MOWER. Compare the illustrations with your lawn mower to familiarize
yourself with the location of various controls and adjustments. Save this manual for
future reference.
These symbols may appear on your lawn mower or in literature supplied with the
product. Learn and understand their meaning.
CAUTION ENGINE ENGINE FAST SLOW CHOKE FUEL OIL DANGER,KEEPHANDS
OR WARNING ON OFF AND FI_E'r AWAY
Throttle Operator presence controlbar
Drive control lever
Starter
handle
Grass catcher
Engine oilcap with dipstick
Muffler
Gasoline filler cap
Housing
Air filter
Primer eeladjuster(oneachwheel)
IMPORTANT: This lawn mower is shipped WITHOUT OIL OR GASOLINE in the engine.
MEETS CPSC SAFETY REQUIREMENTS
Sears rotary walk-behind power lawn mowers conform to the safety standards of the
American National Standards Institute and the U.S. Consumer Product Safety Com-
mission. The blade turns when the engine is running.
Operator presence control bar - must
be held down to the handle to start the
engine. Release to stop the engine.
Starter handle - used for starting the
engine.
Primer- pumps additional fuel from the
carburetor to the cylinder for use when
starting a cold engine. 6
Drive control lever - used to engage
power-propelled forward motion of lawn
mower.
Throttle control - used for starting the
engine and allows you to select either
FAST or SLOW engine speed.

The operation of any lawn
mower can result in foreign
objects thrown into the
eyes, which can result in
severe eye damage.
Always wear safety glasses or eye shields
while operating your lawn mower or
performing any adjustments or repairs.
We recommend standard safety glasses
or a wide vision safety mask worn over
spectacles.
HOWTO USEYOUR LAWN MOWER
ENGINE SPEED
The engine speed is controlled by a
throttle control located on the side of the
upper handle. FAST position is for starting,
normal cutting, trimming and better grass
bagging. SLOW position is for light cutting,
trimming and fuel economy.
SLOW
FAST
ENGINE ZONE CONTROL
_LCAUTION: Federal regulations require
an engine control to be installed on this
lawn mower in order to minimize the
risk of blade contact injury. Do not under
any circumstances attempt to defeat the
function of the operator control. The blade
turns when the engine is running.
•Your lawn mower is equipped with an
operator presence control bar which
requires the operator to be positioned
behind the lawn mower handle to start
and operate the lawn mower.
DRIVE CONTROL
•Self-propelling is controlled by holding
the operator presence control bar down
to the handle and pushing the drive
control lever forward until it clicks;then
releasing the lever.
•Forward motion willstop when the op-
erator presence control bar is released.
To stop forward motion without stopping
engine, release the operator presence
control bar slightly until the drive control
disengages. Hold operator presence
control bar down against handle to con-
tinue mowing without self-propelling.
•To keep drive control engaged when
turning corners, push down on handle
and lift front wheels off ground while
turning lawn mower.
Operator presence control bar Drive
\"-\_ _ "\ _Control
DRIVE
TO ENGAGE CONTROL
DRIVE CONTROL DISENGAGED
TO ADJUST CUTTING HEIGHT
Raise wheels for low cut and lower wheels
for high cut, adjust cutting height to suit
your requirements. Medium position is best
for most lawns.
•To change cutting height, squeeze ad-
juster lever toward wheel. Move wheel
up or down to suit your requirements.
Be sure all wheels are in the same set-
ting.
NOTE: Adjuster is properly positioned
when plate tab inserts into hole in lever.
Also, 9-position adjusters (if so equipped)
allow lever to be positioned between the
plate tabs.
LOWER WHEELS FOR HIGH CUT
Plate tal
RAISE WHEELS FOR LOW CUT Lever
7

TO CONVERT MOWER
Yourlawn mower was shipped ready to be
used as a mulcher. To convert to bagging:
•Lift rear door of the lawn mower and
place the grass catcher frame hooks
onto the door pivot pins.
• To convert to mulching operation, re-
move grass catcher and close rear door.
_'_CAUTION: Do not run your lawn mower
without rear door closed, clipping deflector
or approved grass catcher in place. Never
attempt to operate the lawn mower with
the rear door removed or propped open.
Pivot "Rear Grass
catcher
handle
TO EMPTY GRASS CATCHER
1. Lift up on grass catcher using the
frame handle.
2. Remove grass catcher with clippings
from under lawn mower handle.
3. Empty clippings from bag using both
frame handle and bag handle.
NOTE: Do not drag the bag when empty-
ing; it will cause unnecessary wear.
Grass
catcher
frame
handle
1. Be sure lawnmower is level and area
around oil fill is clean.
2. Remove oil dipstickfrom oil fill spout.
Make sure that rim of spout is clean.
3. You receive a container of oil with the
unit. Slowly pour the entire container
down the oil fill spout into the engine.
4. Wait one minute to allow oil to settle.
Insert and tighten dipstick, then re-
move it to check oil level.
5. Always be sure to retighten oil dipstick
before starting engine.
• Check oil level before each use. Add oil
if needed. Fill to full line on dipstick.
•Change the oil after every 25 hours of
operation or each season. You may
need to change the oil more often under
dusty, dirty conditions.
ADD GASOLINE
•Fill fuel tank to bottom of tank filler neck.
Do not overfill. Use fresh, clean, regular
unleaded gasoline with aminimum of
87 octane. Do not mix oil with gasoline.
Purchase fuel in quantities that can be
used within 30 days to assure fuel fresh-
hess.
•kCAUTION: Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
,_ar an open flame.
CAUTION: Alcohol blended fuels
(called gasohol or using ethanol or metha-
nol) can attract moisture which leads to
separation and formation of acids during
storage. Acidic gas can damage the fuel
system of an engine while in storage. To
avoid engine problems, the fuel system
should be emptied before storage of 30
days or longer. Drain the gas tank, start
the engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel
next season. See Storage Instructionsfor
additional information. Never use engine
or carburetor cleaner products in the fuel
tank or permanent damage may occur.
Bag
handle
BEFORE STARTING ENGINE
ADD OIL
Your lawnmower is shipped without oil in
the engine. For type and grade of oil to oline filler
use, see "ENGINE" in the Maintenance cap
section of this manual.
CAUTION; DO NOT overfill engine with
oil, or it will smoke on startup. Primer
oilcap
8

TO START ENGINE
NOTE: Due to protective coatings on the
engine, a small amount of smoke may be
present during the initialuse of the prod-
uct and should be considered normal.
1. To start a cold engine, push primer
three (3) times before trying to start.
Use a firm push. This step is not
usually necessary when starting an
engine which has already run for a few
minutes.
2. Move throttle control lever to FAST
position.
3. Hold operator presence control bar
down to the handle and pull starter
handle quickly. Do not allow starter
rope to snap back.
TO STOP ENGINE
• To stop engine, release operator pres-
ence control bar.
NOTE: In cooler weather it may be neces-
sary to repeat priming steps. In warmer
weather over priming may cause flooding
and engine will not start. If you do flood
engine, wait a few minutes before attempt-
ing to start and do not repeat priming
steps.
MOWING TIPS
•Under certain conditions, such as very
tall grass, it may be necessary to raise
the height of cut to reduce pushing
effort and to keep from overloading the
engine and leaving clumps of grass
clippings. It may also be necessary to
reduce ground speed and/or run the
mower over the area a second time.
• For extremely heavy cutting, reduce the
width of cut by overlapping previously
cut path and mow slowly.
• For better grass bagging and most cut-
ting conditions, the engine speed should
be set in the FAST position.
• Pores in cloth grass catchers can be-
come filled with dirt and dust with use
and catchers will collect less grass. To
prevent this, regularly hose catcher off
with water and let dry before using.
• Keep top of engine around starter clear
and clean of grass clippings and chaff.
This will help engine air flow and extend
engine life.
MULCHING MOWINGTIPS
IMPORTANT: For best performance, keep
mower housing free of built-up grass and
trash. See "CLEANING" in the Mainte-
nance section of this manual.
•The special mulching blade will recut
the grass clippings many times and
reduce them in sJze so that as they fall
onto the lawn they will disperse into
the grass and not be noticed. Also, the
mulched grass will biodegrade quickly
to provide nutrients for the lawn. Always
mulch with your highest engine (blade)
speed as this will provide the best recut-
ting action of the blades.
• Avoid cutting your lawn when it is wet.
Wet grass tends to form clumps and
interferes with the mulching action. The
best time to mow your lawn is the early
afternoon. At this time the grass has
dried and the newly cut area will not be
exposed to the direct sun.
•For best results, adjust the lawn mower
cutting height so that the lawn mower
cuts off only the top one-third ofthe
grass blades. If the lawn is overgrown it
will be necessary to raise the height of
cut to reduce pushing effort and to keep
from overloading the engine and leaving
clumps of mulched grass. For extremely
heavy grass, reduce your width of cut
by overlapping previously cut path and
mow slowly.
MAX 1/3
Certain types of grass and grass
conditions may require that an area be
mulched a second time to completely
hide the clippings. When doing a second
cut, mow across or perpendicular to the
first cut path.
Change your cutting pattern from week
to week. Mow north to south one week
then change to east to west the next
week. This will help prevent matting and
graining of the lawn.
9

MAINTENANCE SCHEDULE/__o_._:o__o_y
FILL 'N DATES _ __'_€_-_'_*_'s_-_"_O_
,BYou
CheckforLooseFastanem II/'
Clean/InspectGrassCatcher
M CleanLavmMower
_N CleanUnderDriveCover
(Power-Propelled Mowers) ¥1
Check drive belt/pulleys ql_
E {Power.Propailed Mowers)
ChecldSharpan/Replece Blade _t_=l
LubricationChart I_
Clean Battery/Recharge
IElectdc Start iowers_) 1/ I/4
E Check Engine Oil Level 1/
Change EngineOil 1/iJ
GClean Air Filter II/=
I InspectMuffler l/
N Clean or Replace Spark Plug i/
ReplaceAir Filter Paper Cadddge 1/=
1- Cl_nOe rnomoftenwh4mop_ undota he_wyIoKi orInhighwnbkmt_oeratureB,
2- 8awl_ernoreo_m whenof_m_ng indrty ordusty¢ondltlotm.
3. Replaceblade_mornOf_l wlmnmowtng_ _mdy loll,
4. Gha_e 48 hou_ _ =ml of =NJIo_,
GENERAL RECOMMENDATIONS
The warranty on this lawn mower does not
cover items that have been subjected to
operator abuse or negligence. To receive
full value from the warranty, operator
must maintain mower as instructed in this
manual. Some adjustments will need to
be made periodically to properly maintain
your unit.
All adjustments in the Service and Adjust-
ments section of this manual should be
checked at least once each season.
•Once a year, replace the spark plug,
clean or replace air filter element and
check blade for wear. A new spark plug
and clean/new air filter element assure
proper air-fuel mixture and help your
engine run better and last longer.
•Follow the maintenance schedule in this
manual.
BEFORE EACH USE
1. Check engine oil level.
2. Check for loose fasteners.
LUBRICATION
Keep unit well lubricated (See "LUBRI-
CATION CHART").
LUBRICATION CHART
Wheel
adjuster (on
each wheel)
Engine oil
Rear door
hinge
(_) Handle bracket mounting pins
(_) Spray lubricant
(_) See "ENGINE" in Maintenance section.
10
IMPORTANT: Do not oil or grease
plastic wheel bearings. Viscous lubd-
cants will attract dust and dirt that will
shorten the life of the self-lubricating
bearings. If you.feel they must be
lubricated, use only a dry, powdered
graphite type lubricant sparingly.

PRODUCT SPECIFICATIONS
Serial Number:
Date of Purchase:
Gasoline Capacity /Type: 1.6 Quarts (Unleaded Regular)
Oil Type (API-SF-SJ): SAE 30 (above 32°F); SAE 5W-30 (below 32°F)
Oil Capacity: 20 Ounces
Spark Plug (Gap: .020") Champion RC12YC
Blade Bolt Torque: 35-40 ft. Ibs.
The model and serial numbers will be found on a decal on the rear of the lawn mower
housing. Record both serial number and date of purchase in space provided above.
LAWN MOWER
Always observe safety rules when per-
forming any maintenance.
TIRES
•Keep tires free of gasotine, oil, or insect
control chemicals which can harm rub-
ber.
•Avoid stumps, stones, deep ruts, sharp
objects and other hazards that may
cause tire damage.
BLADE CARE
For best results, mower blade must be
kept sharp. Replace bent or damaged
blades.
TO REMOVE BLADE
1. Disconnect spark plug wire trom spark
plug and place wire where it cannot
come in contact with spark plug.
2. Turn lawn mower on its side. Make
sure air filter and carburetor are up.
3. Use a wood block between blade and
mower housing to prevent blade from
turning when removing blade bolt.
NOTE: Protect your hands with gloves
and/or wrap blade with heavy cloth.
4. Remove blade bolt by turning counter-
clockwise.
5. Remove blade and attaching hard-
ware (bolt, lock washer and hardened
washer).
NOTE: Remove the blade adapter and
check the key inside hub of blade adapter.
The key must be in good condition to work
properly. Replace adapter if damaged.
TO REPLACE BLADE
1. Position the blade adapter on the en-
gine crankshafL Be sure key in adapter
and crankshaft keyway are aligned.
2. Position blade on the blade adapter
aligning the two (2) holes in the blade
with the raised lugs on the adapter.
3. Be sure the trailing edge of blade (op-
posite sharp edge) is up toward the
engine.
4. Install the blade bolt with the lock
washer and hardened washer into
blade adapter and crankshaft.
5. Use block of wood between blade and
lawn mower housing and tighten the
blade bolt, turning clockwise.
•The recommended tightening torque is
35-40 ft. Ibs.
IMPORTANT: Blade bolt is grade 8 heat
treated.
TO SHARPEN BLADE
NOTE: We do not recommend sharpening
blade - but if you do, be sure the blade is
balanced.
Care should be taken to keep the blade
balanced. An unbalanced blade will
cause eventual damage to lawn mower or
engine.
• The blade can be sharpened with a file
or on a grinding wheel. Do not attempt
to sharpen while on the mower.
•To check blade balance, ddve a nail into
a beam or wall. Leave about one inch of
the straight nail exposed. Place center
hole of blade over the head of the nail.
If blade is balanced, it should remain in
a horizontal position. If either end of the
blade moves downward, sharpen the
heavy end until the blade is balanced.
Blade adapter, _Crankshaft
k°yway
B,ade Lo_kwas_=rr__. _/
H-'rdo,',e\ " -r' shatt
1 1 washer Trailir Iedge Blade adapter

GRASS CATCHER
• The grass catcher may be hosed with
water, but must be dry when used.
• Check your grass catcher often for dam-
age or deterioration. Through normal
use itwillwear. If catcher needs replac-
ing, replace only with a manufacturer
approved replacement catcher. Give the
lawn mower model number when order-
ing.
DRIVE WHEELS
Check front drive wheels each time before
you mow to be sure they move freely.
The wheels notturning freely means
trash, grass cuttings, etc. are in the drive
wheel area and must be cleaned to free
drive wheels.
If necessary to clean the drive wheels, be
sure to clean both front wheels.
1. Remove hubcaps, hairpin cotters and
washers.
2. Remove wheels from wheel adjusters.
3. Remove any trash or grass cuttings
from inside the dust cover, pinion and/
or drive wheel gear teeth.
4. Put wheels back in place.
NOTE: If after cleaning, the drive wheels
do not turn freely, contact a Sears or other
qualified service center.
GEAR CASE
•To keep your drive system working
properly,the gear case and area around
the drive should be kept clean and free
of trash build-up. Clean under the drive
cover twice a season.
• The gear case is filled with lubricant to
the proper levelat the factory. The only
time the lubricant needs attention is if
service has been performed on the gear
case.
•If lubricant is required, use only Elf
brand oil, Part No. REDUCTELF 100.
Do not substitute.
ENGINE
LUBRICATION
Use only high quality detergent oil rated
with API service classification SF-SJ. Se-
lect the oil's SAE viscosity grade accord-
ing to your expected operating tempera-
tura. 8AE V15C061"_ GRADES
m
'1_ _cp Iop I_* _ _ _ 10_'
W,_ATURE RANGI__ATED _ NEXT01. _A/_QE
NOTE: Although multi-viscosityoils
(5W30, 10W30 etc.) improve starting in
cold weather, these multi-viscosityoils will
result in increased oil consumption when
used above 32°F. Check your engine oil
level more frequently to avoid possible
engine damage from running low on oil.
Change the oil after every 25 hours of
operation or at least once a year ifthe
lawn mower is not used for 25 hours in
one year.
Check the crankcase oil level before start-
ing the engine and after each five (5)
hours of continuous use. Tighten oil plug
securely each time you check the oil level.
TO CHANGE ENGINE OIL
NOTE: Before tipping lawn mower to drain
oil, drain fuel tank by running engine until
fuel tank isempty.
1. Disconnect spark plug wire from spark
plug and place wire where itcannot
come in contact with spark plug.
2. Remove engine oil cap; lay aside on a
clean surface.
3. Tip lawn mower on its side as shown
and drain oil into asuitable container.
Rock lawn mower back and forth to re-
move any oil trapped inside of engine.
4. Wipe off any spilled oil from lawn
mower or side of engine.
5. Fillengine with oil. The engine oil ca-
pacity is 20 oz. Ifoil is not completely
drained from engine, you may not need
the entire container of a 20 oz. bottle of
oil. Slowly pour 3/4 of the oil from the
container down the oil fill spout intothe
engine.
6. Wait one minute to allow oil to settle.
Insert and tighten dipstick, then re-
move it to check oil level.
7. Continue adding small amounts of
oiland rechecking the dipstick untilit
reads full. DO NOT overfill,or engine
will smoke on startup.
8. Always be sure to retighten oil dipstick
before starting engine.
9. Reconnect spark plug wire tospark plug.
Container
12

AIR FILTER
Your engine will not run properly using a
dirty air filter. Clean the foam pre-cleaner
after every 25 hours of operation or every
season. Replace paper cartridge every
100 hours of operation or every season,
whichever occurs first. Service air cleaner
more often under dusty conditions.
1. Loosen screws and remove cover.
2. Carefully remove cartridge.
3. Clean by gently tapping on a flat sur-
face. If very dirty, replace cartridge.
_CAUTION: Petroleum solvents, such as
kerosene, are not to be used to clean car-
tridge. They may cause deterioration of the
cartridge. Do not oil cartridge. Do not use
pressurized air to clean or dry cartridge.
4. Install cartridge, then replace cover.
Base
MUFFLER
Inspect and replace corroded muffler as it
could create a fire hazard and/or damage.
SPARK PLUG
Replace spark plug at the beginning of
each mowing season or after every 100
hours of operation, whichever occurs
first. Spark plug type and gap setting are
shown in "PRODUCT SPECIFICATIONS"
in Maintenance section of this manual.
CLEANING
IMPORTANT: For best performance, keep
mower housing free of built-up grass and
trash. Clean the underside of your mower
after each use.
_CAUTION: Disconnect spark plug wire
from spark plug and place wire where it
cannot come in contact with the spark
plug.
• Clean the underside of your lawn mower
by scraping to remove build-up of grass
and trash.
• Clean engine often to keep trash from
accumulating. A clogged engine runs
hotter and shortens engine life.
• Keep finished surfaces and wheels free
of all gasoline, oil, etc.
• We do not recommend using a garden
hose to clean lawn mower unless the
electrical system, muffler, air filter and
carburetor are covered to keep water
out. Water in engine can result in short-
ened engine life.
CLEAN UNDER DRIVE COVER
Clean under drive cover at least twice a
season. Scrape underside of cover with
putty knife or similar tool to remove any
build-up of trash or grass on underside of
drive cover.
_I_,WARNING: To avoid serious injury,
before performing any service or adjust-
ments:
1. Release control bar and stop engine.
2. Make sure the blade and all moving
parts have completely stopped.
3. Disconnect spark plug wire from spark
plug and place where it cannot come in
contact with plug.
LAWN MOWER
TO ADJUST CUTTING HEIGHT
See "TO ADJUST CUTTING HEIGHT" in
the Operation section of this manual.
REAR DEFLECTOR
The rear deflector, attached between the
rear wheels of your mower, is provided to
minimize the possibility that objects will
be thrown out of the rear of the mower
into the operator's mowing position. If the
deflector becomes damaged, it should be
replaced.
13

TO REMOVE DRIVE BELT
1. Remove drive cover. Remove belt from
gearcase pulley by pushing down on
pulley and rolling belt off it.
2. Turn lawn mower on its side with air
filter and carburetor up.
3. Remove blade.
4. Remove debris shield.
5. Remove belt from engine pulley on
crankshaft.
TO REPLACE DRIVE BELT
1. Install new belt on engine pulley.
2. Reinstall debris shield and blade.
3. Return mower to upright position.
4. Install new belt on gearcase pulley,
5. Reinstall drive cover.
NOTE: Always use factory approved belt
to assure fit and long life.
Drive
cover Belt
TO ADJUST HANDLE
The handle can be mounted in a high or
low position. The mounting holes in the
bottom of lower handle are off center for
raising or lowering the handle.
NOTE: The upper handle has an "anti-
fold" bracket located on the left side of the
handle. This bracket prevents the upper
handle from folding forward, which helps
protect control cable(s) from damage.
1. Remove upper handle and all parts
attached to lower handle.
2. Remove hairpin cotters from lower
handle bracket mounting pin.
3. Squeeze lower handle in to remove it
from mounting pins.
4, Turn lower handle over to raise or
lower handle.
5. Squeeze lower handle in and position
holes onto mounting pins on handle
bracket.
6. Reassemble upper handle and all
parts removed from lower handle.
Anti-fold
bracket
Lower
ROTATE
Mowing
Hairpin
pin LOW POSITION
ENGINE
ENGINE SPEED
Your engine speed has been factory set,
Do not attempt to increase engine speed
or it may result in personal injury. If you
believe that the engine is running too fast
or too slow, take your lawn mower to a
Sears or other qualified service center for
repair and adjustment.
CARBURETOR
Yourcarburetor is not adjustable. If your
engine does not operate properly due to
suspected carburetor problems, take your
lawn mower to a Sears or other qualified
service center for repair and/or adjust-
ment.
IMPORTANT: Never tamper with the
engine governor, which is factory set
for proper engine speed. Overspeeding
the engine above the factory high speed
setting can be dangerous. If you think
the engine-governed high speed needs
adjusting, contact a Sears or other
qualified service center, which has proper
equipment and experience to make any
necessary adjustments.
14

Immediately prepare your lawn mower for
storage at the end of the season or if the
unit will not be used for 30 days or more.
LAWN MOWER
When lawn mower is to be stored for a pe-
riod of time, clean it thoroughly, remove all
dirt, grease, leaves, etc. Store in a clean,
dry area.
1. Clean entire lawn mower (See
"CLEANING" in the Maintenance sec-
tion of this manual).
2. Lubricate as shown in the Maintenance
section of this manual.
3. Be sure that all nuts, bolts, screws,
and pins are securely fastened. Inspect
moving parts for damage, breakage
and wear. Replace if necessary.
4. Touch up a_lrusted or chipped paint
surfaces; sand lightly before painting.
HANDLE
You can fold your lawn mower handle for
storage.
NOTE: The upper handle has an "anti-
fold" bracket located on the left side of the
handle. This bracket prevents the upper
handle from folding forward, which helps
protect control cable(s) from damage.
1. Squeeze the bottom ends of the lower
handle toward each other until the
lower handle clears the handle bracket,
then move handle forward.
2. Loosen upper handle mounting bolts
enough to allow upper handle to be
folded back.
IMPORTANT: When folding the handle for
storage or transportation, be sure to fold
the handle as shown or you may damage
the control cables.
• When setting up your handle from the
storage position, the lower handle will
automatically lock into the mowing posi-
tion.
SQUEEZE
TO FOLD
Operator presence
controlbar
Upper
Lower
handle_
FOLD
BACKWARD
bracket
ENGINE
FUEL SYSTEM
IMPORTANT: It is important to prevent
gum deposits from forming in essential
fuel system parts such as carburetor, fuel
filter, fuel hose, or tank during storage.
Also, alcohol blended fuels (called gasohol
or using ethanol or methanol) can attract
moisture which leads to separation and
formation of acids during storage. Acidic
gas can damage the fuel system of an
engine while in storage.
1. Drain the fuel tank.
2. Start the engine and let it run untilthe
fuel lines and carburetor are empty.
•Never use engine or carburetor cleaner
products in the fuel tank or permanent
damage may occur.
•Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable
alternative in minimizing the formation
of fuel gum deposits during storage. Add
stabilizer to gasoline in fuel tank or stor-
age container. Always follow the mix ratio
found on stabilizer container. Run engine
at least 10 minutes after adding stabilizer
to allow the stabilizer to reach the carbure-
tor. Do not drain the gas tank and carbure-
tor if using fuel stabilizer.
ENGINE OIL
Drain oil (with engine warm) and replace
with clean engine oil. (See "ENGINE" in
the Maintenance section of this manual).
CYLINDER
1. Remove spark plug.
2. Pour one ounce (29 ml) of oil through
spark plug hole into cylinder.
3. Put1starter handle slowly a few times
to distribute oil.
54. Replace with new spark plug.
1

OTHER
• Do not store gasoline from one season
to another.
• Replace your gasoline can if your can
starts to rust. Rust and/or dirt in your
gasoline will cause problems.
• If possible, store your unit indoors and
cover it to protect it from dust and dirt.
°Cover your unit with a suitable protective
cover that does not retain moisture. Do
not use plastic. Plastic cannot breathe,
which allows condensation to form and
will cause your unit to rust.
IMPORTANT: Never cover mower while
_gine and exhaust areas are still warm.
CAUTION: Never store the lawn mower
with gasoline in the tank inside a building
where fumes may reach an open flame or
spark. Allow the engine to cool before stor-
ing in any enclosure.
TROUBLESHOOTING -See appropriate section in manual unless directed
to a Sears Service Center.
PROBLEM CAUSE CORRECTION
Does not start 1. Dirty air filter. 1. Clean/replace air filter.
2. Out of fuel.
3, Stale fuel.
4. Water in fuel.
5. Spark plug wire is
disconnected.
6. Bad spark plug.
7. Loose blade or broken
blade adapter.
8. Control bar in released
position.
9. Control bar defective.
10. Fuel valve lever (if so
equipped) in OFF position.
11.Weak battery (if equipped).
12.Disconnected battery
connector (if equipped).
2. Fill fuel tank.
3. Drain tank and refillwith
fresh, clean fuel.
4. Drain fuel tank and
carburetor and refill tank
with fresh gasoline.
5, Connect wire to plug.
6.
7. Replace spark plug.
Tighten blade bolt or
replace blade adapter.
8. Depress control bar to
handle.
9. Replace control bar.
10.Turn fuel valve lever
to the ON position.
11.Charge battery.
12. Connect battery to engine.
16

TROUBLESHOOTING - See appropriate section in manual unless directed
to a Sears Service Center.
CAUSEPROBLEM
Loss of power
Poor cut -
uneven
Excessive
vibration
Starter rope
hard to pull
1, Rear of lawn mower
housing or cutting blade
dragging in heavy grass,
2, Cutting too much grass.
3, Dirty air filter.
4. Buildup of grass, leaves,
and trash under mower.
5. Too much oil in engine.
6, Walking speed too fast.
1. Worn, bent or loose blade.
2. Wheel heights uneven.
3. Buildup of grass, leaves
and trash under mower.
1. Worn, bent or loose blade.
2. Bent engine crankshaft.
2.
3.
4.
Engine flywheel brake is on
when control bar is released.
Bent engine crankshaft,
Blade adapter broken.
Blade dragging in grass.
CORRECTION
1, Set to"Higher Cut"
position.
2. Set to "Higher Cut"
position.
3. Clean/replace air filter.
4. Clean underside of mower
housing.
5. Check oil level.
6. Cut at slower walking speed.
1. Replace blade. Tighten
blade bolt.
2. Set all wheels at same
height.
3. Clean underside of
mower housing.
1. Replace blade. Tighten
blade bolt.
2. Contact a Sears or other
qualified service center.
1. Depress control bar to
upper handle before
pulling starter rope.
2. Contact a Sears or other
qualified service center.
3. Replace blade adapter.
4. Move lawn mower to cut
grass or to hard surface.
Grass catcher 1. Cutting height too low. 1. Raise cutting height.
not filling 2. Lifton blade worn off. 2. Replace blade.
(If so equipped) 3. Catcher not venting air. 3. Clean grass catcher.
Hard to push 1. Raise cutting height.
1, Grass is too high or wheel
height is too low.
2. Rear of lawn mower
housing or cutting blade
dragging in grass.
3. Grass catcher too full.
4. Handle height position not
right foryou.
Loss of drive
Ior slowing of
' drive speed
1. Belt wear.
2, Belt off of pulley.
3. Drive cable worn or broken.
4. Dirt in drive pinions.
2. Raise rear of lawn mower
housing one (1) setting
higher.
3. Empty grass catcher.
4. Adjust handle height to suit.
1. Check/replace drive belt.
2, Check/reinstall drive belt.
3. Replace drive cable.
4. Clean drive pinions.
17

Garantfa ......................................................... 18
Reglas de Seguridad ................................ 18-20
Montaje /Pre-Operacibn ............................... 21
Operaci6n ................................................. 22-25
Mantenimiento .......................................... 26*29
Programa de Mantenimiento ......................... 26
Especificaciones del Producto ....................... 27
Servicio y Adjustes ................................... 29-31
Almacenamiento ....................................... 31-32
Identificaci6n de problemas ...................... 32-33
Servicio Sears .......................................... 35-43
Orden de Partes ............................... Contratapa
GARANT[A LIMITADA DE DOS AI_IOS PARA LA SEGADORA A MOTOR CRAFTSMAN
For dos (2) aSos, apartir de la fecha de compra, cuando esta Segadora Craftsman se mantenga,
lubrique y aline seg_n _s instrucciones para la operacibn yel mantenimiento en el manual del
duefio, Sears reparard gratis todo defecto en el material y la mano de obra.
Si la Segadora Craftsman se usa pare fines comerciales o de arriendo, esta garantia s61ose aplica
por noventa (90) dfas a partir de la fecha de compra.
Esta Garantia no cubre:
•Artfculos que se desgastan durante el uso normal tales como las cuchillas segadoras rotatorias,
los adaptadores de la cuchllla, las correas, los filtros de aire y las buj_as.
•Reparaciones necesarias debido al abuso o ala negligencia del operador, incluy_ndose a los
cigQeSales dobladoe y ala falta de mantenimiento del equipo segOn las instrucciones que se
incluyenen el manual del dueho.
EL SERVICIO DE GARANT(A ESTA DISPONIBLE al devolver la segadora a motor Craftsman al
centro/departmento de servicio Sears mas cercano en los Estados Unidos. Esta garantia se apUca
solamente mientras el producto este en uso en los Estados Unidos.
Esta Garantfa le otorga derechos legales especfficos, y puede qua tambien tenga otros derechos
que varfan de estado a estado.
SEARS, ROEBUCK AND CO., D/817WA, HOFFMAN ESTATES, IL 60179 USA
IMPORTANTE: Esta maquina cortadaora es capaz de amputar las manos y los manos y los pies y
de lanzar objetos. Si no se observan lee instrucciones de seguridad siguientes se pueden producir
lesionas graves o la muerte.
_Busque este simbolo que setSala las precau-
clones de segurida.d de importancia. Quiere
decir- IIIATENClON!!!iiiESTE ALERTO!!! SU
SEGURIDAD ESTA
COMPROMETIDA.
_,DVERTENCIA: Siempre desconecte el
atambre de ta bujla y p6ngalo donda no pueda
entrar en contacto con la bujfa, para evitar el
arranque por accidente, durante la preparaci6n,
el transporte, el ajuste o cuando se hacen
reparaciones.
_s.DVERTENCIA: Los bornes, terminales y
acceeorioe relativos de la batert'a contienen
plomo o compuestos de plomo, productos
qufmicos conocidos en el Estado de California
como causa de cdncer y defeetos al nacimiento
uotros dafios reproductivos. Lavar las manos
despu6s de manipulerlos.
_PRECAUCI6N: El tubo de escape del motor,
algunos de sus constituyentesy algunos com-
ponentes del vehiculo contienen o desprenden
productosqufmicos conocidos en el Estado de
California come causa de c&ncery defectos al
nacimiento u otros dafios reproductivos.
_I=PRECAUCI(_N: El silenciadoryotras
piezas del motor Uegan a sre extremadamente
calientes durante la operacidn y siguen siendo
ealientes despuds de qua el motor haya parado.
Para evitar quemaduras severas, permanezca
lejos de estas dreas.
18

I. OPERACION
• Antes de empezar, debe familiarizarse
completamente con los controlesy el use
correcto de la maquina. Para esto, debe leer
ycomprender todas las instrucciones que
aparecen en la maquina yen los manuales
de operaci6n.
• No ponga las manes o toe pies oerca o
debajo de las partes rotatorias. Mant_ngase
siempre lejos de la abertura de la descarga.
• Permita que solamente las personas re-
sponsables que est_n familiarizadas con las
instruccionesoperen la mAquina.
•Despeje el _,reade objetos tales come pie-
dras, juguetes, alambres, huesos, palos, etc.
que pueden ser recog{dosy lanzados per las
cuchillas.
• Asegerese que el Area no se hallen per-
sonas, antes de segar. Pare la mAquina si
alguien entra en el Area.
• No opere la maqaina sin zapatos o con
sandalias abiertas. P6ngase siempre zapatos
s611dos.
• No tire de {a segadora hacia atr_s a menos
que sea absolutamente necesario. Mire
siempre hacia abajo y hacia detrAs antes y
mientras que se mueve hacia atr_s.
•No opera la segadora sin los respectivos
resguardos, las placas, el reCogeder de
c_sped u otros aditamentos dise ados para
su proteccion y seguridad.
Refi_rase alas instrucoionee del fabrieante
para el funcionamiento e instalaci6n de
accesorios. Use _nicamente accesorios apro-
bados per el fabricante.
• Detenga la cuchilla o las cuohillas cuando
cruce per calzadas, calles o caminos de
grava.
• Parar el motor cada vez que se abandona el
aparato, antes de limpiar la segadora o de
remover residues del tube.
• Apagar el motor y esperar hasta que las
cuchiltas est6n completamente paradas antes
de remover el receptor de hierba.
• Segar solamente con luz del dia o con una
buena luz artificial.
•No opera la mAquina bajo la influencia del
alcohol o de las drogas.
• Nunca opera la maquina cuando la hierba
est_ mojada. Aseg,',rese siempre de tenet
buena tracoi6n ensus pies; mantenga el
mango firmemente y camine; nunca corra.
• Desconectar el mecanismo de propulsi6n
autbnoma o el embrague de transmisi6n en
las segadoras que Io tienen antes de poner
en marcha el motor.
• Si el equipo empezara a vibrar de una
manera anormat, pare el motor y revise de
inmediato para averiguar la ¢ausa. General-
mente la vibraci6n suele indicar que existe
alguna averfa.
• Siempre use galas de seguddad o anteojos
con protecci6n lateral cuando opera la sega-
dora.
II. OPERACION SOBRE LAS CUESTAS
Los accidentes ocurren con md$ frecuencia en
las cuestas. Estos accidentes ocurren debido a
resbaladas ocaldas, las cuales pueden resultar
en graves lesiones. Operar la recortadora en
cuestas requiere mayor concentraci6n. Si se
siente inseguro en una cuesta, no la recorte.
HACER:
• Puede recortar a trav_s de la superficie de
la cuesta, nunca hacia ardba y hacia abajo.
Proceda con extrema precauci6n cuando
cambie de direcci6n en las cuestas.
•Renueva redes los objetos extrafios, tales
come guijarros, ramas, etc.
• Debe preatar atenci6n a hoyos, baches o
protuberancias. Recuerde que la hierba alta
puede esconder obstdculos.
NO HACER:
• No recorte cerca de pendientes, zanjas o
terraplenes. El operador puede perder la
tracci6n en los pies o el equilibrio.
• No recorte cuestas demasiado inclinadas.
• No recorte en hierba mojada. La reducoi6n
en la tracci6n de la pisada puede causar
resbalones.
III. NII_IOS
Se pueden producir acoidentes trAgicos si el
operador no presta ateneibn a la presencia
de los nifios, A menudo, los nifios se sienten
atraidos per la mdquina y per la actividad de
la siega. Nunca suponga que los nifios van a
permanecer en el mismo lugar donde los vie
per m]ltimavez.
•Mantenga a los nifios alejados del Area de
la siega y bajo el cuidado estricto de otra
persona adu_ta responsab_e.
• Est6 alerta y apague la mAquina sihay nifios
que entran al Area.
•Antes y cuando este retrocodiendo, mire
hacia atrAs y hacia abajo para veriflcar si hay
nifios pequefios.
•Nunca permita que los nifios operen la md-
quina.
•Tenga un cuidado extra cuando se acerque
a esquinas donde no hay vislbilidad, a los
arbustos, _.rboles u otros objetos que pueden
interferir con su Ifnea de visi6n.
IV. SERVICIO
• Tenga cuidado extraal manejar la gasolina y
los demAs combustibles. Son inflamables y
los gases son explosives.
- Use soLamente un envase aprobado.
°Nunca remueva la tapa del depbsito de
gasolina o agregae combustible con el mo-
tor funcionando. Permita que el motor se
enfrie antes de velvet a pone combustible.
No fume.
Nunca vuelva a porter combustible en la
mdquina en recintos cerrados.
-Nunca almacene ta mdqulna o el envase
del combustible dentro de algdn lagar en
deride haya una llama expuesta, tal come
la del calentador de agua.
19

•Nunca haga funcionar una m&quina dentro
de un &tea cerrada.
• Nunca haga aiustes o reparaciones mientras
el motor est_ en marcha. Desconecte el
cable de la bujM, y mant_ngalo a cierta
distanda de _sta pare prevenir un arranque
accidental.
•Mantenga las tuercas y los pernos, espe-
cialmente los pemos del accesorio de ta
cuchilla, epretados y mantenga el equipo en
buenas condiciones.
• Nunca manipu}e de forma indebida los
dispositivos de seguridad. Controle regular-
mente su funcionamiento correcto.
• Mantenga la mfiquina libre de hierba, hojas
u otras acumulaciones de desperdicio.
Limpie los derrames de aceite o combustible.
Permita que la m&quina se entrie antes de
atmacenada.
• Pare einspeccione el equipo si le pega a un
objeto. Rep&relo, si es necesario, antes de
hacado arranCaro
•En ningOncaso hay que regular la altura de
las ruedas mientras el motorest& en marcha.
•Los componentes del receptor de la hierba
van sujetos a desgaste, da£=osy deterioro,
que pueden exponer las partes en mov-
imiento o permitir que objetos seen diapara-
dos, Controlar frecuentemente y cuando sea
necesario sustituir con partes aconsejadas
por el labricanta.
• Las cuchillas de la segadora est&n afiladas
y pueden cortar. Cubrir las hojas o Ilevar
guantes, y utilizer precauciones especiales
¢uando se efect0a mantenimiento sobre las
mismas.
• No cambie el ajuste del reguMdor del motor
ni exceda su velocidad.
Estos accesorios estaban disponibles cuando $e produjo la segadora. No son fa¢llitados Junto
at cortecesped. Est_,ndisponibles en Lamayoda de las tiendas de Sears yen los centros de
servicio.La mayoda de las tiendas Sears tambi_n paeden mandar a pedir partes de repuesto
pare usted, si les propomiona el nOmarodel modelo de su segadora. Algunos de astos accesorios
tat vez no se aptiquen a su segadora,
RENDIMIENTO DE LA SEGADORA
DESVIADOR
DE RECORTES
PAPA SEGADORAS
CON DESCARGA
7RASERA
RECOREDOR
PAPA
8EGADORAS
CON DESCAFIGA
TRASERA
ESTABILP
==-
RECOREDOR
PAPA
S_
GONDESCARGA
LATERAL
MANTENIMIENTO DE LA SEGADORA
81LENCtADORE8
CORREAS ¢UCHILLAS ©
ADAPTADOflES
DE _LA
RLlmOE DE AIRE
RU_
BUJUUm
ACEnl_
DEk MOTOR
2O