Craftsman 917.378430 User manual

Owner's Manual
JCRRFT.TMRWI
6.75 HORSEPOWER
21" REAR DISCHARGE
POWER PROPELLED
ROTARY LAWN MOWER
Model No.
917.378430
• Safety
•Assembly
•Operation
•Maintenance
•Espa6ol
• Repair Parts
CAUTION:
Read and follow all
Safety Rules and Instructions
before operating this equipment
Sears, Roebuck and Co., Hoffman Estates, IL 60179
Visit our Craftsman websfte: www.sears.com/craftsman

Warranty ............................................... 2
Safety Rules ......................................... 2
Assembly .............................................. 5
Operation .............................................. 6
Maintenance Schedule ...................... 10
Maintenance ....................................... f 0
Product Specifications ........................ 11
Service and Adjustments .................... 13
Storage ............................................... 15
Troubleshooting ................................. 16
Repair Parts ........................................ 35
Parts Ordering ..................... Back Cover
LIMITEDTWOYEAR WARRANTY ON CRAFTSMAN POWER MOWER
For two years from date of purchase, when this Craftsman Lawn Mower is maintained,
lubricated, and tuned up according to the operating and maintenance instructions in
the owner's manual, Sears will repair free of charge any defect in material or workman-
ship.
If this Craftsman Lawn Mower is used for commercial or rental purposes, this warranty
applies for only 90 days from the date of purchase.
This Warranty does not cover:
• Expendable items which become worn during normal use, such as rotary mower
blades, blade adapters, belts, air cleaners and spark plug.
• Repairs necessary because of operator abuse or negligence, including bent
crankshafts and the failure to maintain the equipment according to the instructions
contained in the owner's manual.
Warranty service is available by returning the Craftsman power mower to the nearest
Sears Service Center/Department in the United States. This warranty applies only
while this product is in use in the United States.
This Warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
Sears, Roebuck and Co., D/817 WA, Hoffman Estates, Illinois 60179
IMPORTANT: This cutting machine is capable of amputating hands and feet and
throwing objects. Failure to observe the following safety instructions could result in
serious injury or death.
I. GENERAL OPERATION
•Read, understand, and follow all
instructions on the machine and in the
manual(s) before starting. Be thor-
oughly familiar with the controls and
the proper use of the machine before
starting.
• Do not put hands or feet near or under
rotating parts. Keep clear of the
discharge opening at all times.
• Only allow responsible individuals,
who are familiar with the instructions, to
operate the machine.
•Clear the area of objects such as
rocks, toys, wire, bones, sticks, etc.,
which could be picked up and thrown
by the blade.
•Be sure the area is clear of other
people before mowing. Stop machine if
anyone enters the area.
• Do not operate the mower when
barefoot or wearing open sandals.
Always wear substantial foot wear.
•Do not pull mower backwards unless
absolutely necessary. Always look
down and behind before and while
moving backwards.
•Do not operate the mower without
proper guards, plates, grass catcher or
other safety protective devices in place.
•See manufacturer's instructions for
proper operation and installation of
accessories. Only use accessories
2approved by the manufacturer.

•Stop the blade(s) when crossing gravel
drives, walks, or roads.
•Stop the engine (motor) whenever you
leave the equipment, before cleaning
the mower or unclogging the chute.
• Shut the engine (motor) off and wait
until the blade comes to complete stop
before removing grass catcher.
• Mow only in daylight or good artificial
light.
•Do not operate the machine while
under the influence of alcohol or drugs.
•Never operate machine in wet grass.
Always be sure of your footing: keep a
firm hold on the handle and walk; never
run.
•Disengage the self-pmpened mecha-
nism or drive clutch on mowers so
equipped before starting the engine
(motor).
•if the equipment should start to vibrate
abnormally, stop the engine (motor)
and check immediately for the cause.
Vibration is generally a warning of
trouble.
•Always wear safety goggles or safety
glasses with side shields when
operating mower.
I1. SLOPE OPERATION
Slopes are a major factor related to slip
and fall accidents which can result in
severe injury. All slopes require extra
caution. If you feel uneasy on a slope, do
not mow it.
DO:
•Mow across the face of slopes: never
up and down. Exercise extreme caution
when changing direction on slopes.
• Remove obstacles such as rocks, tree
limbs, etc.
•Watch for holes, ruts, or bumps. Tall
grass can hide obstacles.
DO NOT:
•Do not trim near drop-offs, ditches or
embankments. The operator could lose
footing or balance.
•Do not trim excessively steep slopes.
•Do not mow on wet grass. Reduced
footing could cause slipping.
III. CHILDREN
Tragic accidents can occur if the operator
is not alert to the presence of children.
Children are often attracted to the
machine and the mowing activity. Never
assume that children will remain where
you last saw them.
•Keep children out of the trimming area
and under the watchful care of another
responsible adult.
•Be alert and turn machine off if children
enter the area,
•Before and while walking backwards,
look behind and down for small
children.
•Never allow children to operate the
machine.
•Use extra care when approaching blind
corners, shrubs, trees, or other objects
that may obscure vision.
IV. SERVICE
•Use extra care in handling gasoline
and other fuels. They are flammable
and vapors are explosive.
-Use only an approved container.
-Never remove gas cap or add fuel
with the engine running. Allow
engine to cool before refueling. Do
not smoke.
- Never refuel the machine indoors.
- Never store the machine or fuel
container inside where there is an
open flame, such as a water heater.
•Never run amachine inside a closed
area.
•Never make adjustments or repairs with
the engine (motor) running. Disconnect
the spark plug wire, and keep the wire
away from the plug to prevent acciden-
tal starting.
• Keep nuts and bolts, especially blade
attachment bolts, tight and keep
equipment in good condition.
• Never tamper with safety devices.
Check their proper operation regularly.
• Keep machine free of grass, leaves, or
other debris build-up. Clean oil or fuel
spillage. Allow machine to cool before
storing.
• Stop and inspect the equipment if you
strike an object. Repair, if necessary,
before restarting.
• Never attempt to make wheel height
adjustments while the engine (motor) is
running.
• Grass catcher components are subject
to wear, damage, and deterioration,
which could expose moving parts or
allow objects to be thrown. Frequently
check components and replace with
manufacturer's recommended parts,
when necessan!.
•Mower blades are sharp and can cut.
Wrap the blade(s) or wear gloves, and
use extra caution when servicing them.
•Do not change the engine governor
setting or overspeed the engine.
3

_,Look for this symbol to point out
important safety precautions. It means
CAUTION!!! BECOMEALERT!!! YOUR
SAFETY IS INVOLVED.
A CAUTION= In order to prevent
accidental starting when setting up,
transporting, adjusting or making repairs,
always disconnect spark plug wire and
place wire where it cannot contact spark
plug.
ACAUTION: Muffler and other engine
parts become extremely hot during
operation and remain hot after engine
has stopped. To avoid severe burns on
contact, stay away from these areas.
_IIWARNING: Engine exhaust, some of its
constituents, and certain vehicle
components contain or emit chemicals
known to the State of California to cause
cancer and birth defects or other
reproductive harm.
A,WARNING: Battery posts, terminals and
related accessories contain lead and lead
compounds, chemicals known to the State
of California to cause cancer and bidh
defects or other reproductive harm. Wash
hands after handling.
These accessories were available when this lawn mower was produced. They are not
shipped with your mower. They are also available at most Sears retail outlets and
service centers. Most Sears stores can also order repair parts for you, when you
provide the model number of your lawn mower. Some of these accessories may not
apply to your lawn mower.
LAWN MOWER PERFORMANCE
CLIPPING DEFLECTOR
FOR REAR DISCHARGE LAWN MOWERS
GRASS CATCHERS
FOR
REAR DISCHARGE
LAWN MOWERS
LAWN MOWER MAINTENANCE
MULCHER KITS
GRASS CATCHERS
FOR
SIDE DISCHARGE
LAWN MOWERS
MUFFLERS
BELTS BLADES
AIR FILTERS
BLADE AOAI_'ERS WHEELS
STABILIZER
GAS CANS
SPARK PLUGS
ENGINE OIL
4

Read these instructions and this manual
in its entirety before you attempt to
assemble or operate your new lawn
mower.
IMPORTANT: This lawn mower is
shipped WITHOUT OIL OR GASOLINE in
the engine.
Your new lawn mower has been as-
sembled at the factory with the exception
of those parts left unassembled for
shipping purposes. All parts such as nuts,
washers, bolts, etc., necessary to com-
plete the assembly have been placed in
the parts bag. To ensure safe and proper
operation of your lawn mower, all parts
and hardware you assemble must be
tightened securely. Use the correct tools
as necessary to ensure proper tightness.
TO REMOVE LAWN MOWER FROM
CARTON
1. Remove loose parts included with
mower.
2. Cut down two end comers of carton
and lay end panel down flat.
3. Remove all packing materials except
padding between upper and lower
handle and padding holding operator
presence control bar to upper handle.
4. Roll lawn mower out of carton and
check carton thomugly for additional
loose parts.
HOWTO SET UPYOUR LAWN
MOWER
TO UNFOLD HANDLE
IMPORTANT: Unfold handle carefully so
as not to pinch or damage control cables.
1. Raise handles until lower handle
section locks into place in mowing
position.
2. Remove protective padding, raise
upper handle section into place on
lower handle and tighten both handle
knobs.
3. Remove handle padding holding
operator presence control bar to
upper handle.
Your lawn mower handle can be adjusted
for your mowing comfort. Refer to "Adjust
Handle" in the Service and Adjustments
section of this manual.
Operator
control bar
Liftu
,g
position
Lower handle
TO PREPARE BATTERY
NOTE: Your battery must be charged
before you can start your lawn mower.
1. Disconnect engine battery connector
(male) from battery connector (female)
2. Connect battery charger connector
(male) to battery connector (female).
3. Plug battery charger into 110 volt A.C.
outlet.
4. Leave battery charger connected for
24 hours before starting your engine
for the first time.
5. After charging, connect engine
connector (male) to battery connector
(female).
Your engine has an integral alternator for
partial charging. Connect your battery
charger to charge battery as required.
IMPORTANT: The engine alternator will
not charge a discharged battery.
At the end of the mowing season the
battery should be charged for 48 hours to
protect the battery during winter storage.
_kCAUTION: Always disconnect the
engine connector (male) from the battery
connector (female) to prevent accidental
starting when transporting or storing your
lawn mower after the season.
Battery connector
Engine
5 connector (male) Battery charger

KNOWYOUR LAWN MOWER
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
LAWN MOWER. Compare the illustrations with your lawn mower to familiarize yourself
with the location of various controls and adjustments. Save this manual for future
reference.
These symbols may appear on your lawn mower or in literature supplied with the
product. Learn and understand their meaning.
CAUTION ENGINE ENGINE FAST SLOW CHOKE FUEL OIL DANGER, KEEP HANDS
OR WARNING ON OFF ANO FEET AWAY
Engine zone controlcable Operator presence control bar
Ddve control lever
Auxiliary e knob
Gasoline cap
Housing
Engine
IMPORTANT: This lawn mower is Wheel adjuster
shipped WITHOUT OIL OR GASOLINE (on each wheel)
in the engine,
MEETS CPSC SAFETY REQUIREMENTS
Sears rotary walk-behind power lawn mowers conform to the safety standards of the
American National Standards Institute and the U,S. Consumer Product Safety Commis-
sion. The blade turns when the engine is running.
Operator presence control bar -must
be held down to the handle to start the
engine. Release to stop the engine,
Key start switch- used for starting the
engine.
Auxiliary starter handle -used for
starting the engine.
Primer -pumps additional fuel from the
carburetor to the cylinder for use when
starting a cold engine.
Drive control lever -used to engage
power-propelled forward motion of lawn
mower.
6

Theoperation of any lawn
mower can result in
foreign objects thrown into
the eyes, which can result
in severe eye damage.
Always wear safety glasses or eye
shields while operating your lawn mower
or performing any adjustments or repairs.
We recommend a wide vision safety
mask over spectacles or standard safety
glasses.
HOWTO USEYOUR LAWN MOWER
ENGINE SPEED
The engine speed was set at the factory
for optimum performance. Speed is not
adjustable.
ENGINE ZONE CONTROL
_iLCAUTION: Federal regulations require
an engine control to be installed on this
lawn mower in order to minimize the dsk
of blade contact injury. Do not under any
circumstances attempt to defeat the
function of the operator control. The blade
turns when the engine is running,
•Your lawn mower is equipped with an
operator presence control bar which
requires the operator to be positioned
behind the lawn mower handle to start
and operate the lawn mower.
TO ADJUST CU'FrlNG HEIGHT
Raise wheels for low cut and lower
wheels for high cut, adjust cutting height
to suit your requirements. Medium
position is best for most lawns.
To change cutting height, squeeze
adjuster lever toward wheel. Move
wheel up or down to suit your require-
ments. Be sure all wheels are in the
same setting.
NOTE: Adjuster is properly positioned
when plate tab inserts into hole in lever.
Also, 9-position adjusters (if so equipped)
allow lever to be positioned between the
plate tabs. PlateTab
LowerWheelsfor HighCut / _,dlk
(._ Lever
Raise Wheets for Low Cut
TO CONVERT MOWER
Yourlawn mower was shippedready tobe
usedas a mulcher. Toconverttobagging:
REAR BAGGING
•Liftrear doorofthe iawn mowerand place
the grasscatcher frame hooksontothe
doorpivotpins.
•To convertto mulchingoperation,remove
grasscatcher and close reardoor.
_CAUTION: Do not run your lawn mower
without clipping deflector or approved
grass catcher in place. Never attempt to
operate the lawn mower with the rear
door removed or propped open,
Pivot Grass catcher
handle
Catcher
TO EMPTY GRASS CATCHER
1. Open door and lift up on grass catcher
using the frame handle,
2. Remove grass catcher with clippings
from under lawn mower handle.
3. Empty clippings from bag using both
frame handle and bag handle.
NOTE: Do not drag the bag when
emptying; it will cause unnecessary wear.
/
Bag ca_herframe
handle handle

DRIVE CONTROL
• Self-prepelling is controlled by holding
,the operator presence control bar down
to the handle and pushing the drive
control lever forward until it clicks; then
releasing the lever.
•Forward motion wilt stop when the
operator presence control bar is
released. To stop forward motion
without stopping engine, release the
operator presence control bar slightly
until the drive control disengages. Hold
operator presence control bar down
against handle to continue mowing
without self-prepelling.
• To keep drive control engaged when
turning corners, push down on handle
and lift front wheels off ground while
turning lawn mower.
Operator presence control bar
/\ Drive
_'\ /_ _ -- control
_" drive control_" disengaged
BEFORE STARTING ENGINE
ADD OIL
Your lawnmower is shipped without oil in
the engine. Engine holds 20 oz. of oil.
For type and grade of oil to use, see
"ENGINE" in Maintenance section of this
manual.
1. Be sure lawnmower is level and area
around oil fill is clean.
2. Remove engine oil cap and fill to the
full line on the dipstick. Pour oil slowly.
Do not over fill.
NOTE: Allow oil to settle down into engine
for accurate reading. To read proper level,
tighten engine oil cap, then remove it to
read the dipstick.
3. Reinstall engine oil cap and tighten.
• Check oil level before each use. Add
oil if needed. Fill to full line on dipstick.
• Change the oil after every 25 hours of
operation or each season. You may
need to change the oil more often
under dusty, dirty conditions.
ADD GASOLINE
• Fill fuel tank. Use fresh, clean, regular
unleaded gasoline with a minimum of
87 octane. Do not mix oil with gaso-
line. Purchase fuel in quantities that
can be used within 30 days to assure
fuel freshness.
_I,WARNING: Experience indicates that
alcohol blended fuels (called gasohol or
using ethanol or methanol) can attract
moisture which leads to separation and
formation of acids during storage. Acidic
gas can damage the fuel system of an
engine while in storage. To avoid engine
problems, the fuel system should be
emptied before storage of 30 days or
longer. Drain the gas tank, start the
engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel
next season. See Storage Instructions for
additional information. Never use engine
or carburetor cleaner products in the fuel
tank or permanent damage may occur.
_k CAUTION= Fill to bottom of gas tank
filler neck. Do not overfill. Wipe off any
spilled oil or fuel. Do not store, spill or
use gasoline near an open flame.
•Gasoline
filler cap
Engine
oil cap
TO START ENGINE
NOTE: Due to protective coatings on the
engine, a small amount of smoke may be
present during the initial use of the
product and should be considered
normal.
1. To start a cold engine, push primer
three (3) times before trying to start.
Use a firm push. This step is not
usually necessary when starting an
engine which has already run for a
few minutes.
2. Hold operator presence control bar
down to the handle.
3. Turn electric start key clockwise to
crank engine.
8

IMPORTANT: Do not crank engine more
than five continous seconds between
each'time you try to start. Wait 5 to 10
seconds between each attempt.
1. To start _ngine using the auxiliary
starter handle, follow the steps above.
Exchange the use ofthe start key for
starter handle. Pull starter handle
quickly. Do not allow starter rope to
snap back.
TO STOP ENGINE
•To stop engine, release operator
presence control bar.
NOTE: In cooler weather it may be
necessary to repeat priming steps. In
warmer weather over priming may cause
flooding and engine will not start. If you
do flood engine wait a few minutes before
attempting to start and do not repeat
priming steps.
MOWlNGTIPS
•Under certain conditions, such as very
tall grass, it may be necessary to raise
the height of cut to reduce pushing
effort and to keep from overloading the
engine and leaving clumps of grass
clippings. It may also be necessary to
reduce ground speed and/or run the
lawn mower over the area a second
time.
•For extremely heavy cutting, reduce the
width of cut by overlapping previously
cut path and mow slowly.
•For better grass bagging and most
cutting conditions, the engine speed
should be set in the fast position.
• When using a rear discharge lawn
mower in moist, heavy grass, clumps of
cut grass may not enter the grass
catcher. Reduce ground speed
(pushing speed) and/or run the lawn
mower over the area a second time.
•If a trail of clippings is left on the right
side of a rear discharge mower, mow in
a clockwise direction with a small
ovedap to collect the clippings on the
next pass.
•Pores in cloth grass catchem can
become filled with dirt and dust with
use and catchers will collect less grass.
To prevent this, regularly hose catcher
off with water and let dry before using.
•Keep top of engine around starter clear
and clean of grass clippings and chaff.
This will help engine air flow and
extend engine life.
MULCHING MOWINGTIPS
IMPORTANT: For best performance,
keep mower housing free of built-up
grass and trash. See "Cleaning" in
Maintenance section of this manual.
•The special mulching blade will recur
the grass clippings many times and
reduce them in size so that as they fall
onto the lawn they will disperse into the
grass and not be noticed. Also, the
mulched grass will biodegrade quickly
to provide nutrients for the lawn.
Always mulch with your highest engine
(blade) speed as this will provide the
best recutting action of the blades.
•Avoid cutting your lawn when it is wet.
Wet grass tends to form clumps and
interferes with the mulching action.
The best time to mow your lawn is the
early afternoon. At this time the grass
has dried and the newly cut area will
notbe exposed to the direct sun.
•For best results, adjust the lawn mower
cutting height so that the lawn mower
cuts off only the top one-third of the
grass blades. If the lawn is overgrown
it wilt be necessary to raise the height
of cut to reduce pushing effort and to
keep from overloading the engine and
leaving clumps of mulched grass. For
extremely heavy mulching, reduce your
width of cut by overlapping previously
cut path and mow slowly.
• Certain types of grass and grass
conditions may require that an area be
mulched a second time to completely
hide the clippings. When doing a
second cut, mow across or perpendicu-
lar to the first cut path.
• Change your cutting pattern from week
to week. Mow north to south one week
then change to east to west the next
week. This will help prevent matting
and graining of the lawn.
Max1/3

MAINTENANCE SCHEDULE
FILL IN DATES
AS YOU COMPLETE
REGULAR SERVICE 3ERVICE DATES
Check for Loose Fasteners (/' t/
Clean/Inspect Grass Catcher
(IfEquipped) I/ I,/ t/
CleanLawnMower I/ v'
Clean Under Ddve Cover
!Power-Propelled Mowers)
Check ddve Pelt] ulleys
{Power-Propell_Mowers) ¥/
ChecWSharpeniReplace Blade (I/3
Lubrication Chart f_ Ip/
Clean Battery/ReChar(
(Electrk: Start Mowers li/ 11/4
Check Engine Oil Level I/
Change Engine Oil _1.2
Clean Air Filter _ 2
Inspect Muffler _/
Clean or Replace Spark Plug t/
Replace Air Filter Paper Cartridge li/2
1 - Ct_ange more c_en when operating under a heavy loador in highaml_ent temperatureS.
2 - Service more oftenwhen operatt=_gindir_' or duslyconddiC_s.
3-Replace blades mo_ often when mowLngIn sandy SOil.
4 Charge 48 hours at end of season.
GENERAL RECOMMENDATIONS
The warranty on this lawn mower does
not cover items that have been subjected
to operator abuse or negligence. To
receive full value from the warranty,
operator must maintain mower as
instructed in this manual.
Some adjustments will need to be made
periodically to properly maintain your
unit.
All adjustments in the Service and
Adjustments section of this manual
shoutd be checked at least once each
season.
• Once a year, replace the spark plug,
clean or replace air filter element and
check blade for wear. A new spark
plug and clean/new air filter element
assures proper air-fuel mixture and
helps your engine run better and last
longer.
• Follow the maintenance schedule in
this manual.
BEFORE EACH USE
1. Check engine oil level.
2. Check for loose fasteners.
LUBRICATION
Keep unit well lubricated (See "LUBRI-
CATION CHART").
LUBRICATION CHART
_) Wheeladjuster
) Brake spdngbracket
(_ Handle bracket mounting pin
(_ Refer to maintenance "Engine" section.
_) Spray lubricant
IMPORTANT: Do not oil or grease
plastic wheel bearings, viscous lubri-
cants will attract dust and dirt that will
shorten the life of the self-lubricating
bearings, ifyou feel they must be
lubricated, use only a dry, powdered
graphite type lubricant sparingly.
10

PRODUCT SPECIFICATIONS
SE_IALNUMBER
DATE OF PURCHASE
GASOLINE CAPACITY/TYPE: 1.5 QUARTS
UNLEADED REGULAR
OtLTYPE (API-SF-SJ): SAE 30 (ABOVE 32°F)
SAE 5W-30 (BELOW 32°F)
OIL CAPACITY: 20 OZS.
SPARK PLUG (GAP: .045") CHAMPION RESISTOR TYPE RJ 19LM4
BLADE BOLTTORQUE: 35-40 FT. LBS.
• The model and serial numbers will be found on a decal attached to the rear of the
lawn mower housing.Record both serial number and date of purchase in space
provided above.
LAWN MOWER
Always observe safety rules when
performing any maintenance.
TIRES
• Keep tires free of gasoline, oil, or insect
control chemicals which can harm
rubber.
• Avoid stumps, stones, deep ruts, sharp
objects and other hazards that may
cause tire damage.
BLADE CARE
For best results, mower blade must be
kept sharp. Replace bent or damaged
blades.
TO REMOVE BLADE
1. Disconnect spark plug wire from spark
plug and place wire where it cannot
come in contact with spark plug.
2. Tum lawn mower on its side. Make
sure air filter and carburetor are up.
3. Use a wood block between blade and
mower housing to prevent blade from
turning when removing blade bolt.
NOTE: Protect your hands with gloves
and/or wrap blade with heavy cloth.
4. Remove blade bolt by turning counter-
clockwise.
5. Remove blade and attaching hard-
ware (bolt, lock washer and hardened
washer).
NOTE: Remove the blade adapter and
check the key inside hub of blade
adapter. The key must be in good condi-
tion to work properly. Replace adapter if
damaged.
TO REPLACE BLADE
1. Position the blade adapter on the
engine crankshaft. Be sure key in
adapter and crankshaft keyway are
aligned.
2. Position blade on the blade adapter
aligning the two (2) holes in the blade
with the raised lugs on the adapter.
3. Be sure the trailing edge of blade
(opposite sharp edge) is up toward
the engine.
4. Install the blade bolt with the lock
washer and hardened washer into
blade adapter and crankshaft.
5. Use block of wood between blade and
lawn mower housing and tighten the
blade bolt, turning clockwise.
• The recommended tightening torque is
35-40 ft. Ibs.
IMPORTANT: Blade bolt is grade 8 heat
treated.
TO SHARPEN BLADE
NOTE: We do not recommend sharpen-
ing blade - but if you do, be sure the
blade is balanced.
Care should be taken to keep the blade
balanced. An unbalanced blade will
cause eventual damage to lawn mower
or engine.
•The blade can be sharpened with a file
or on a grinding wheel. Do not attempt
to sharpen while on the mower.
• To check blade balance, drive a nail
into a beam or wall. Leave about one
inch of the straight nail exposed. Place
center hole of blade over the head of
the nail. If blade is balanced, it should
remain in a horizontal position. If either
end of the blade moves downward,
sharpen the heavy end until the blade
is balanced.
11

Lockwasher
Blade adapter Crankshaft
Key_ keyway
Crank
bolt Hardened Blade
washer Trailingedge adapter
GRASS CATCHER
•The grass catcher may be hosed with
water, but must be dry when used.
•Check your grass catcher often for
damage or deterioration. Through
normal use it will wear. If catcher
needs replacing, replace only with a
manufacturer approved replacement
catcher. Give the lawn mower model
number when ordering.
DRIVE WHEELS
Check front drive wheels each time
before you mow to be sure they move
freely.
The wheels not turning freely means
trash, grass cuttings, etc. are in the drive
wheel area and must be cleaned to free
drive wheels.
If necessary to clean the drive wheels,
check both front wheels.
1. Remove hubcaps, hairpin cotters and
washers.
2. Remove wheels from wheel adjusters.
3. Remove any trash or grass cuttings
from inside the dust cover, pinion and/
or drive wheel gear teeth.
4. Put wheels back in place.
NOTE: If after cleaning, the drive wheels
do not turn freely, contact a Sears or other
qualified service center.
GEAR CASE
•To keep your drive system working
properly, the gear case and area
around the drive should be kept clean
and free of trash build-up. Clean under
the drive cover twice aseason.
•The gear case is filled with lubricant to
the proper level at the factory. The only
time the lubricant needs attention is if
service has been performed on the
gear case.
• If lubricant is required, use only Texaco
Starplex Premium 1 Grease, Part No.
750369. Do not substitute.
ENGINE
LUBRICATION
Use onty high quality detergent oil rated
with API service classification SF-SJ.
Select the oil's SAE viscosity grade
according to your expected operating
temperature.
SAE V_SCC'SITY GRADES
12
NOTE: Although multi-viscosity oils
(5W30, 10W30 etc.) improve starting in
cold weather, these multi-viscosity oils
will result in increased oil consumption
when used above 32°E Check your
engine oil level more frequently to avoid
possible engine damage from running
low on oil.
Change the oil after every 25 hours of
operation or at least once ayear if the
lawn mower is not used for 25 hours in
one year,
Check the crankcase oil level before
starting the engine and after each five (5)
hours of continuous use. Tighten oil plug
securely each time you check the oil
level,
TO CHANGE ENGINE OIL
NOTE: Before tipping lawn mower to
drain oil, drain fuel tank by running
engine until fuel tank is empty.
I. Disconnect spark plug wire from spark
plug and place wire where it cannot
come in contact with spark plug.
2. Remove engine oil cap; lay aside on a
clean surface.
3. Tip lawn mower on its side as shown
and drain oil into a suitable container.
Rock lawn mower back and forth to
remove any oil trapped inside of
engine.
4. Wipe off any spilled oil on lawn mower
and on side of engine.
5. Fill engine with oil. (See "Add Oil" in
the Operacion section of this manual.)
6, Reconnect spark plug wire to spark
plug.
Container _

AIR FILTER
Your engine will not run properly and may
be damaged by using adirty air filter.
Replace the air filter every year or after
every 100 hours of operation, more often
if you mow in very dusty, dirty conditions.
Do not wash air filter.
TO CHANGE AIR FILTER
1. Remove the air filter by turning
clockwise to the stop and pull away
from collar.
2. Remove filter from inside of cover.
3. Clean the inside of the cover and the
collar to remove any dirt accumula-
tion.
4. Insert new filter into cover.
5. Put air filter cover and filter into collar
aligning the tab with the slot.
6. Push in on cover and turn counter-
clockwise to tighten.
Collar
Turn
clockwise
remove
Turn
Airfilter cover counter-
clockwise
totighten
MUFFLER
Inspect and replace corroded muffler as it
could create a fire hazard and/or dam-
age.
SPARK PLUG
Replace spark plugs at the beginning of
each mowing season or after every 100
hours of operation, whichever occurs first.
Spark plug type and gap setting are
shown in "PRODUCT SPECIFICATIONS"
in Maintenance section of this manual.
CLEANING
IMPORTANT: For best performance,
keep mower housing free of built-up
grass and trash, Clean the underside of
your mower after each use.
ACAUTION: Disconnect spark plug wire
from spark plug and place wire where it
cannot come in contact with the spark
plug.
• Clean the underside of your fawn
mower by scraping to remove build-up
of grass and trash,
• Clean engine often to keep trash from
accumulating. A clogged engine runs
hotter and shortens engine life.
•Keep finished surfaces and wheels free
of all gasoline, oil,etc.
•We do not recommend using a garden
hose to clean lawn mower unless the
electrical system, muffler, air filter and
carburetor are covered to keep water
out. Water in engine can result in
shortened engine life,
CLEAN UNDER DRIVE COVER
Clean under drive cover at least twice a
season. Scrape underside of cover with
putty knife or similar tool to remove any
build-up of trash or grass on underside of
drive cover.
ACAUTION: Before performing any
service or adjustments:
1. Release control bar and stop engine.
2. Make sure the blade and all moving
parts have completely stopped.
3. Disconnect spark plug wire from spark
plug and place where it cannot come
in contact with plug.
LAWN MOWER
TO ADJUST cU'rFING HEIGHT
See "TO ADJUST CUTTING HEIGHT" in
the Operation section of this manual.
REAR DEFLECTOR
The rear deflector, attached between the
rear wheels of your mower, is provided to
minimize the possibility that objects will
be thrown out of the rear of the mower
into the operator mowing position. If the
deflector becomes damaged, it should be
replaced.
13

TO REMOVE/REPLACE DRIVE BELT
1. Remove drive cover. Remove belt
• from gearcase pulley by pushing
down on pulley and roiling belt off it.
2. Turn lawn mower on its side with air
filter and carburetor up.
3. Remove blade.
4. Remove debris shield•
5. Remove belt from engine pulley on
crankshaft.
6. Install new belt by reversing above
steps.
7. Always use factory approved belt to
assure fit and long life.
Drive
NOTE: if vinyl bindings are too stiff, hold
them in warm water for a few minutes. If
bag gets wet, let it dry before using.
_CAUTION: Do not run your lawn
mower without clipping deflector or
approved grass catcher in place. Never
attempt to operate the lawn mower with
the rear door removed or propped open.
Catcher
BeLt
Push
down
TO ADJUST HANDLE
The upper handle may be adjusted to
four (4) different height positions.
1. Loosen both handle knobs only
enough to allow the upper handle to
pivot to the desired adjustment
position•
2. Tighten both handle knobs securely.
Handle Knob
Handle Knob
TO ASSEMBLE GRASS CATCHER
1, Put grass catcher frame into grass bag
with rigid part of bag on the bottom.
Make sure the frame handle is outside
of the bag top.
2, Slip vinyl bindings over frame.
_t Frame
opening
ENGINE
ENGINE SPEED
Your engine speed has been factory set.
Do not attempt to increase engine speed
or it may result in personal injury. If you
believe that the engine is running too fast
or too slow, take your lawn mower to a
Sears or other qualified service center for
repair and adjustment.
CARBURETOR
Your carburetor has a non-adjustable
fixed main jet for mixture control• If your
engine does not operate properly due to
suspected carburetor problems, take
your lawn mower to a Sears or other
qualified service center for repair and/or
adjustment.
IMPORTANT: Never tamper with the
engine governor, which is factory set for
proper engine speed, Overspeeding the
engine above the factory high speed
setting can be dangerous. If you think the
engine-governed high speed needs
adjusting, contact a Sears or other
qualified service center, which has
proper equipment and experience to
make any necessary adjustments•
14

Immediately prepare your lawn mower for
storage at the end of the season or if the
unit will not be used for 30 days or more.
LAWN MOWER
When lawn mower is to be stored for a
period of time, clean it thoroughly, remove
all dirt, grease, leaves, etc. Store in a
clean, dry area.
1. Clean entire lawn mower (See
"CLEANING" in the Maintenance
section of this manual).
2. Lubricate as shown in the Mainte-
nance section of this manual.
3. Be sure that all nuts, bolts, screws,
and pins are securely fastened.
Inspect moving parts for damage,
breakage and wear. Replace if
necessary.
4. Touch up all rusted or chipped paint
surfaces; sand lightly before painting.
HANDLE
You can fold your lawn mower handle for
storage.
1. Squeeze the bottom ends of the lower
handle toward each other until the
lower handle clears the handle
bracket, then move handle forward.
2. Loosen upper handle mounting bolts
enough to allow upper handle to be
folded back.
IMPORTANT: When folding the handle
for storage or transportation, be sure to
fold the handle as shown or you may
damage the control cables.
•When setting up your handle from the
storage position, the lower handle will
automatically lock into the mowing
position. Lower handle
Sq bracket
co_er
Operator presence
control bar
Upper handle
Foldforward for
stroage
Fold
backward
Mowing
position
Lower handle
ENGINE
FUEL SYSTEM
IMPORTANT: It is important to prevent
gum deposits from forming in essential
fuel system parts such as carburetor, fuel
filter, fuel hose, or tank during storage.
Also, experience indicates that alcohol
blended fuels (called gasohol or using
ethanol or methanol) can attract moisture
which leads to separation and formation
of acids during storage. Acidic gas can
damage the fuel system of an engine
while in storage.
1. Drain the fuel tank.
2. Start the engine and let it run until the
fuel fines and carburetor are empty.
• Never use engine or carburetor cleaner
products in the fuel tank or permanent
damage may occur.
• Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable
alternative in minimizing the formation of
fuel gum deposits during storage. Add
stabilizer to gasoline in fuel tank or
storage container. Always follow the mix
ratio found on stabilizer container. Run
engine at least 10 minutes after adding
stabilizer to allow the stabilizer to reach
the carburetor. Do not drain the gas tank
and carburetor if using fuel stabilizer.
ENGINE OIL
Drain oil (with engine warm) and replace
with clean engine oil. (See "ENGINE" in
the Maintenance section of this manual).
15

CYLINDER
1. Remove spark plug.
2.. Pour one ounce (29 ml) of oil through
spark plug hole into cylinder.
3. Pull starter handle slowly a few times
to distribute oil.
4. Replace with new spark plug.
BAI-FERY
Disconnect the battery from the engine
connector and charge battery 48 hours.
OTHER
•Do not store gasoline from one season
to another.
•Replace your gasoline can if your can
starts to rust, Rust and/or dirt in your
gasoline will cause problems.
• If possible, store your unit indoors and
cover it to give protection from dust and
dirt.
• Cover your unit with a suitable protec-
tive cover that does not retain mois-
ture. Do not use plastic. Plastic cannot
breathe which allows condensation to
form and will cause your unit to rust.
IMPORTANT: Never cover mower while
engone and exhaust areas are still warm.
CAUTION:Never store the lawn mower
with gasoline in the tank inside a building
where fumes may reach an open flame or
spark. Allow the engine to cool before
storing in any enclosure.
TROUBLESHOOTING CHART
PROBLEM CAUSE
Does not start 1, Dirty air filter.
2, Out offuel.
3, Stale fuel,
4, Water in fuel.
5, Spark plug wire is
disconnected.
6. Bad spark plug.
7. Loose blade or broken
blade adapter.
8. Control bar in released
position,
9, Control bar defective,
10.Weak Battery
11.Disconnected battery
connector.
CORRECTION
1. Clean/replace air filter.
2. Fill fuel tank.
3. Drain tank and refill with
fresh clean fuel.
4. Drain fuel tank and
carburetor and refill tank
with fresh gasoline.
5. Connect wire to plug.
6. Replace spark plug.
7. Tighten blade bolt or
replace blade adapter.
8. Depress control bar to
handle.
9. Replace control bar.
10.Charge battery.
11.Connect battery to engine.
16

TROUBLESHOOTING CHART
PROBLEM CAUSE
Loss of power
3.
4.
5.
6.
Poor cut - 1.
uneven 2.
3.
Excessive
vibration
1. Rear of lawn mower
housing or cutting blade
dragging in heavy grass.
2. Cutting too much grass.
Starter rope hard 1.
topull
2.
3.
4.
Loss of drive 1.
2.
Grass catcher 1.
notfilling (ifso 2.
equipped) 3.
Hard topush 1.
2,
3.
4.
Dirty air filter.
Buildup of grass, leaves,
and trash under mower.
Too much oil in engine.
Walking speed too fast.
Worn, bent or loose blade.
Wheel heights uneven.
Buildup of grass, leaves
and trash under mower.
Worn, bent or loose blade.
Bent engine crankshaft.
CORRECTION
1. Set to "Higher Cut"
position,
2. Set to "Higher Cut"
position.
3. Clean/replace air filter.
4. Clean underside of mower
housing.
5. Check oil level.
6. Cut at slower walking
speed.
1. Replace blade. Tighten
blade bolt.
2. Set all wheels at same
height
3. Clean underside of
mower housing.
1. 1. Replace blade. Tighten
blade bolt.
2. 2. Contact a Sears or other
qualified service center.
Engine flywheel brake is on 1.
when control bar is released
Bent engine crankshaft.
Blade adapter broken.
Blade dragging in grass.
2,
3.
4.
Depress control bar to
upper handle before
pulling starter rope.
Contact a Sears or other
qualified service center.
Replace blade adapter.
Move lawn mower to cut
grass or to hard surface.
Drive wheels not turning 1. Adjust or replace drive
with drive control engaged, control cable.
Belt not driving 2. Put belt on pulleys or
replace belts if broken.
Cutting height too low. 1. Raise cutting height.
Lift on blade worn off. 2. Replace blade.
Catcher not venting air. 3. Clean grass catcher.
1. Raise cutting height.
Grass is too high or wheel
height is too low.
Rear of lawn mower
housing or blade dragging
in grass.
Grass catcher too full.
Handle height position not
right for you.
2. Raise rear of lawn mower
housing one (1) setting
higher.
3. Empty grass catcher.
4, Adjust handle height to
suit,
17

Garant{a .............................................. 18
Reglas de Seguridad ......................... 18
Montaje ............................................... 21
Operaci6n ........................................... 22
Mantenimiento .................................... 26
Programa de Mantenimiento .............. 26
Especificaciones del Producto ........... 27
Servicio y Adjustes ............................. 30
Almacenamiento ................................ 31
Identificaci6n de problemas ............... 33
Partes de repuesto ......... Vea el manual
ingles del dueSo
GARANTiA LIMITADA DE DOS AltOS PARA LA SEGADORA A MOTOR CRAFTSMAN
Par dos (2) aSos, a partir de la fecha de compra, cuande esta Segadora Craftsman se
mantenga, lubrique y atine segt_n las instrucciones para la operacibn y el mantenimiento en el
manual del dueho, Sears reparar& gratis tode defecto en el material y la mano de obra.
Si la Segadora Craftsman se usa para fines comerciales o de ardendo, esta garantfa s61o se
aplica por noventa (90) dfas a partir de la fecha de compra.
Esta Garantia no cubre:
•Articulos que se desgastan durante el uso normal tales como las cuehiltas segadoras
rotatodas, los adeptadores de la cuchilla, las correas, los filtros de aire y las bujfas.
•Reparaciones necesarias debido al abuso o ala negligencia del operador, incluy_ndcee a los
cig0ehales doblados y a la falta de mantenimiento del equipo segt_n las instmcciones que se
incluyen en el manual del dueSo.
EL SERVIClO DE GARANTiA ESTA DiSPONIBLE al devolver la segadpra a motor Craftsman al
Centro/Departmento de Servicio Seam mas cercano en los Estades Unidos. Esta garantfa se
aplica solamente mientras el producto este en uso en los Estades Unidos.
Esta Garantla le otorga derechos legales especfficos, y puede que tambi_n tenga otros
derachos que varfan de estade a estado.
Sears, Roebuck and Co., D/817 WA, Hoffman Estates, Illinois 60179 USA
IMPORTANTE: Esta maquinacortadaoraes capaz de amputar las manos y los manesy los
piesy de lanzarobjetos.Si no se observanlas instrucciones de seguridadsiguientesse pueden
producir lesiones graves o la muerte.
I.OPERACION
•Antes de empezar, debe familiarizarse
completamente con los controles y el uso
correcto de la maquina. Para esto, debe leer
y comprender todas las instrucciones que
aparecen en la maquina yen los manuales
de operacibn.
•No ponga las manos o los pies cerca o
debajo de las partes rotatodas. Mant_ngase
siempre lejos de la abertura de la descarga.
•Permita que solamente las personas
responsables que estdn familiadzadas con
las instrucciones operen la maquina.
•Despeje el _trea de objetos tales como
piedras, juguetes, alambres, huesos, palos,
etc. que pueden ser recogidos y lanzados
por las cuchillas.
•Asegdrese que el &rea no se hallen
personas, antes de segar. Pare la m&quina
si alguien entra en el _rea.
•No opere la maquina sin zapatos o con
sandalias abiertas. P6ngase siempre
zapatos s61idos. 18
No tire de la segadora hacia atrds amenos
que sea absolutamente necesado. Mire
siempra hacia abajo y hacia detr&s antes y
mientras que se mueve hacia atrds.
No opera la segadora sin los respectivoa
resguardos, las placas, el recogeder de
c_sped u otrce aditamantce dise ados pare
su proteccibn y seguddad.
Refi_rase alas instrucciones del fabdcante
para el funcionamiento einstalacibn de
accesorios. Use t_nicamente accesorice
aprobades por el fabdcante.
Detenga la cuchilla o las cuchillas cuande
cruce per calzades, calles ocaminos de
grava.
Parar el motor cade vez que se abandena
el aparato, antes de limpiar la segadera o de
remover residuce del tubo.
Apagar el motor y esperar hasta que las
cuchillas est_n completamante paradas
antes de remover el receptor de hierba.
Segar solamente con luz del dfa o con una
buena luz artificial.
No opere la mdquina bajo la influencia del
alcohol o de las drogas.

• Nuncaoperalamaquinacuandolahierba
est6mojada.Aseg,3resesiempradetener
buena traccibn ensus pies; mantenga el
mango finnemente y camine; nunca corra.
• Dessonectar el mecanismo de pmpulsi6n
autbnoma o e| embrague de transmisibn en
las segadoras qua Io tienen antes de poner
en marcha el motor.
•Si el equipo empezara a vibrar de una
manera anormal, pare el motor y revise de
inmediato para avedguar ta causa.
Generalmente la vibraci6n susie indicar qua
exists alguna aveda.
•Siempre use gafas de segurided o anteojos
con pmteccibn lateral cuando opera la
segadora.
I1. OPERACION SOBRE LAS CUESTAS
Los accidentes ocurran con rods frecuencia
en las cuestas. Estos accidentes ocurren
debido a resbaladas o ca_das, las cua_as
pueden resultar en graves lesiones. Operar la
recortadora en cuestas requiere mayor
concentraei6n. Si se siente inseguro en una
cuesta, no la recorte.
HACER:
•Puede recortar a tray,s de la superficie de
ta cuesta, nunca hada arriba yhacia abaje.
Proceda con extrema precaucibn cuande
cambie de direcci6n en las euestas.
•Renueva redes los oblates extraSos, tales
come guijarros, ramas, etc.
•Debe prestar atencibn a hoyos, baches o
protuberancias. Recuerde que la hierba alta
puede esconder obstdculos.
NO HACER:
•No recorte serca de pendientes, zanjas o
tarraptenes. El opsrador puede perder la
traccibn en los pies o el equilibrio.
• No recede cuestas demasiado inclinadas.
•No resorts en hlerba mojada. La reducci6n
en la tracci6n de la pisada puede causar
resbalones.
III.NI_OS
Se p_eden prodecir acc'Identes tr,_g_cossi el
operador no presta atencibn a la pmsencia de
los nit_os.A menudo, los ni_os se sienten
atraldos per la mdquina y per la actividad de la
siega. Nunca suponga qua los nihos van a
permanecer en el mismo lugar donde los via
per dltima vez.
•Mantenga a los ni6os ale_dos del drea de la
siega y bajo el cuidado estricto de otra
persona adulta responsable.
•Estd alerta y apague la mdquina si hay ni_os
qua entran at _raa.
•Antes y cuando este retrocediendo, mira
hacia atrds y hacia abajo pera vedficar si
hay niSos pequeSos.
•Nunca permita qua los nihos operen la
mdquina.
•Tenge un cuidedo extra cuando se acerque
aesquinas donde no bay visibilidad, a los
arbustos, drboles uotros objetos que
pueden interfefir con su }_nea de visi6n.
IV. SERVICIO
•Tenga cuidado extra al manejar la gasolina
y los demds combustibtes. Son inflarnables
ylos gases son explosives.
-Use solamente un envase aprobado.
- Nunca remueva la tapa del dep6sito de
gasotina o agregue combustive con el
motor funcionando. Permita qua eI motor
se enfrfe antes de velvet a pone
combustible. No fume.
- Nunca vuelva a porter combustible en la
m_quina en recintos cerrados.
- Nunca almacene la mdquina o el envase
del combustible deetro de alg_n lugar en
donde haya una llama expuesta, tal come
la del calentador de agua.
•Nunca haga funcionar una mdquina dentro
de un _rea cerrada.
•Nunca haga ajustes o reparaciones
mientras el motor estd an marcha.
Desconecte el cable de la bujfa, y
mantengalo a cierta distancia de _sta para
prevenir un arranque accidental.
•Mantenga las tuercas y los pemos,
especialmente los pemos de_accesofio de
la cuchilla, apratados y mantenga el equipo
en buenas coediciones.
•Nunca manipule de forma indebida los
dispositivos de seguridad. Controls
regularmente su funcionamiento correct(>.
•Mantenga la mdquina libre de hierba, hojas
uotras acumulaciones de desperdicio.
Limpie los derrames de aceite o combus-
tible. Permita qua la maquina se enfrie antes
de almacenarla.
•Pare e;nspeccione el equipo si le pega a un
objeto. Repdrelo, si as necesario, antes de
hacerlo arrancar.
•En ningun case hay que regular la altura de
las ruedas mientras el motor estd en
marcha.
•Los componentes del receptor de la hierba
van sujetos a desgaste, da_os yd_er_oro,
que pueden exponer las partes en
rnovimiento o permitir que ob)etos sean
disparados. Controlar frecuentemente y
cuando sea necesado sustituir con partes
aconsejadas per el fabdcante.
•Las cuchillas de la segadora estdn afilades
y pueden cortar. Cubrir las bolas o Uevar
guantes, y utUizar precauciones especiales
cuando se efectua mantenimiento sobre las
mismas.
•No cambie el ajuste det regutador de_motor
ni exceda su velocidad.
19

,_Busque este simbolo que se_ia ias precaudo-
nes de segurided de impoltanda. Quiere decir-
iiiA"FENC3_)NI!! iiiESTE ALERTOH! SU
SEGURIDAD ESTA COMPROMETIDA.
_J=RECAILICI(3N: Siel_pre desconecte el
alambre de _abujia ypbngalo donde no pueda
entmr en contactocon la bujia, para evitar el
arranque por accidente, durante la prepamdbn, el
transpofte, el ajuste o cuando se hacen
reparaciones.
_kPRECAUCI(_N: El silenciador y otras piezas
del motor Itegan a ser extremadamente
calientes durante ia operacibn y siguen siendo
calientes despu_s de que el motor haya
parado. Para evitar quemaduras severas,
permanezca lejos de estas ,_reas.
_DVERTENCIA: El tubo de escape del motor,
elgunos de sus cons_uyentes y algunos
componentes del vehfculo _n o
despmnden productos qufrnic_ conoeldos e_ el
Estado de California como causa de cdncery
defectos al nacirniento u otros dahos
rt_productJvos.
_kADVERTENCIA: LOSbomes, terminales y
accesorios relaifvosde la bateda contienen plomo
o compuestos de plomo, productos qu/micos
conocido_en el Estado de California como causa
de c&ncery defectosal nadmiento u otros dahos
reproducifvos.Lavar las manos despuds de
manipularlos.
Estos accesorios estaban disponibles cuando se produjo la segaclora. No son
facilitados junto al cortacesped. Tambien estan disponibles en la mayorfa de las
tiendas de Sears yen los centros de sewicio. La mayoda de las tiendas Sears
tambidn pueden mandar apedir partes de repuesto para usted, si les proporciona el
ndmero del modelo de su segadora. Atgunos de estos accesorios tal vez no se
apliquen a su segadora.
RENDIMIENTO DE LA SEGADORA
PARA SEGADORAS CON OESCARGA TRASERA JUEGO S PARA LA ACOLCHADORA ESTABILIZADORES
SEGADORAS SEGADORAS
CON DESCARGA CON DESCARGA
TRASERA LATERAL ENVASES
DE GASOLINA
MANTENIM|ENTO DE LA SEGADORA
S_LENCIADORES FIt.TROS DE AIRE BUJJAS
CORREAS C UCHILLAS DE CUCHILLA RUEDAS DEL MOTOR
20