Craftsman 917.255560 User manual

i OwNeR'S
I MODELNO.
"Caution:
Read and follow
all Safety Rules
and Instructions
Before Operating
Th_s Equipment
-,_:, ,:_,_=_ _=•7¸ _ ::
CRRFrXiVlnN+
12.0 HP iC
ELECT C START
38" OWER ECK
5 SPEED TRANSAXLE
LAWN TRACTO
, Assembly
, Operation
,Customer Responsibiliti"es
•Service and Adjustment
•Repair Parts
Sears, Roebuck and Coo,Chicago, _L60684 U°SoA,

SAFETY RULES
Safe Operation Practices for Ride-On Mowers
IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEETAND THROWING OBJECTS
FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERtOUS INJURY OR DEATH
LGENERAL OPERATION
*Read, understand, and follow all instructions in the manual
and on the machine before starting.
, Only allow responsible adutts, who are familiar with the
instructions, to operate the machine.
,Clear the area of objects such as rocks, toys, wire, etc., which
could be picked up and thrown by the blade.
, Besuretheareaisclearofotherpeoplebeforemowing. Stop
machine ff anyone enters the area.
, Never carry passengers.
, Do not mow in reverse unless absolutely necessary. Always
look down and behind before and while backing.
-Be aware of the mower discharge direction and do not point
it at anyone. Do not operate the mower without either the
entire grass catcher or the guard in place.
*Slow down before turning.
, Never leave a running machine unattended. Always turn off
blades, set parking brake, stop engine, and remove keys
before dismounting.
o Turn off blades when not mowing.
, Stop engine before removing grass catcher or unclogging
chute.
° Mow only in daylight or good artificial light.
, Do not operate the machine while under the influence of
alcohol or drugs.
o Watch for traffic when operating near or crossing roadways.
o Use extra care when toading or unloading the machine into a
trailer or truck.
H. SLOPE OPERATION
Slopes are a major factor related to toss-of-control and tipover
accidents, which can result in severe injury or death. All slopes
require e._.r_ caution. Ifyou cannot back up the slope or if you feel
uneasy on it, do not mow it,
DO:
• Mow up and down slopes, not across.
o Remove obstacles such as rocks, tree Uimbs,etco
,Watch for holes, ruts, or bumps. Uneven terrain could
overturn the machine. TaPgrass can hide obstacles.
Use slow speed. Choose a low gear so that you will not have
to stop or shift while on the slope.
" FollowIhemanufacturer'srecommendationsforwheelweights
or counterweights to improve stability.
• Use extra care with grass catchers or other attachments.
These can change the stability of the machine.
oKeep ail movement on the slopes slow and gradual Do not
make sudden changes in speed or direction.
,Avoid starting or stopping on a slope, tf tires lose traction,
disengage the blades and proceed slowly straLghtdown the
slope.
DO NOT:
oDo not turn on slopes untess necessary, and then, turn slowly
and gradually downhill, if possible.
,Do not mow near drop-offs, ditches, or embankments. The
mower could suddenly turn over if a wheel is over the edge of
a cliff or ditch, or ff an edge caves in.
oDo _ot mow on wet grass. Reduced traction could cause
sliding.
°Do not try to stabilize the machine by putting your foot on the
ground.
oDo not use grass catcher on steep slopes.
HI. CHILDREN
Tragic accidents can occur ff the operator is not alert to th_
presence of children. Children are often attracted tothe machin_
and the mowing activity. Never assume that children wil! remair
where you last saw them.
o Keep children out of the mowing area and under the watchfu
care of another responsible adult.
, Be alert and turn machine off if children enter the area.
, Before and when backing, took behind and down for smaf
children.
, Never carry children. They may falt off and be serious!_
injured or interfere with the safe machine operation.
, Never allow children to operate the machine.
, Use extra care when approaching blind corners, shrubs,
trees, or other objects that may obscure vision.
!V. SERVICE
• Use extra care in handling gasoline and other fuels. They
are flammabIe and vapors are explosive.
Use only an approved container.
Never remove gas cap or add fuel with the engine
running. Allow engine to cool before refueling. Do no_
smoke.
Never refuel the machine indoors.
Never store the machine or fue! container inside where
there is an open flame, such as a water heater.
- Never run a machine inside a closed area.
o Keep nuts and bolts, especially blade attachment bolts, tight
and keep equipment in good condition.
o Never tamper with safety devices. Check their proper
oper._tion regularly.
• Keep machine free of grass, leaves, or other debris build-up.
Clean oil or fuel spillage. Allow machine to cool before
storing,
o Stop and inspect the equipment if you strike an object.
Repair, if necessary, before restarting.
•Never make adjustments or repairs with the engine running.
• Grass catcher components are subject to wear, damage,
and deterioration, which could expose moving parts or allow
objects to be thrown. Frequently check components and
replace with manufacturer's recommended parts, when nec-
essary.
oMower blades are sharp and can cut. Wrap the blade(s) or
wear gloves, and use extra caution when servicing them.
oCheck brake operation frequently. Adjust and service as
required.
Look for this symbol to point out Impor-
tant safety precautions. It means
CAUTION!!! BECOME ALERT!l! YOUR
SAFETY ISINVOLVED.
CAUTION: Always dEscet_nect spark
plug wire and place wlre where It cannot
contact spark plug in order to prevent
accidental starting when setting up,
transporting, adjusting or making
repabso
•

H_
CONGRATULATIONS on your purchase of a Sears
Tractor. {t has been designed, engineered and manu+
factured to give you the best possible dependability and
performance.
Should you experience any problem you cannot easily
remedy, please contact your nearest Sears Service
Center/Department. We have competent, weil-trained
technicians and the proper tools to service or repair this
unit,
Please read and retain this manual. The instructions will
enable you to assemble and maintain your unit properfy.
Always obse_e the '+SAFETY RULES".
MODEL
NUMBER 9t7.255560
SERIAL
NUMBER
DATE OF PURCHASE
THE MODELAND SERIAL NUMBERS WfLLBE FOUND
ON A PLATE UNDER THE SEAT.
YOU SHOULD RECORD BOTH SER ALNUMBERAND
DATE OF PURCHASE AND KEEP IN A SAFE PLACE
FOR FUTURE REFERENCE.
MAINTENANCE AGREEMENT
A Sears Maintenance Agreement isavailable on this prod-
uct, Contact your nearest Sears store for details.
CUSTOMER RESPONSIBlUTIES
+ Read and observe the safety rules.
+Follow a regular schedule in maintaining, caring for and
using your unit.
II 11 1!
°Fo+lowthe instructions under Maintenance and Stor+
age" sections of this owner's manual.
PRODUCT SPECIFICATIONS
HORSEPOWER: 12.0
GASOLINE CAPACITY: 5 QUARTS
UNLEADED REGULAR
OIL (3,0 PINTS): SAE 30 (or 10W-30)
WINTER: SAF..5W-30
SPARK PLUG(GAP.030 iN.): CHAMPION RJ-19LM
STD361458
VALVE CLEARANCE: INTAKE ,005 - .007 iN.
EXHAUST .009 -.0t t IN,
GROUND SPEED: FORWARD
1st 1ot0 MPH
2nd 2.00 MPH
3rd 3.00 MPH
4th 4.20 MPH
5th 5,00 MPH
REVERSE: 1.50 MPH
TIRE PRESSURE: FRONT: 14 PSi
REAR: 10 PSI
CHARGING SYSTEM: 3 AMPS BATTERY
5 AMPS HEADLIGHTS
BLADE BOLT TORQUE: 30+35 FT, LBS,
WARNING: This unit is equipped with an internal combus-
tion engine and should not be used on or near any unim-
proved forest-covered, brush-covered or grass-covered
land unless the engine's exhaust system is equipped with
a spark arrester meeting applicable local or state laws (if
any), if a spark arrester +sused, it should be maintained in
effective working order by the operator.
ln the state of California the above is required by _aw
(_Section 4442 of=the California Public Resources Code).
Other states may have similar laws. Federal laws apply on
,_ federal lands. A spark arrester for the muffler is available
through your nearest Sears Authorized Service Center
(See REPAIR PARTS section of this manua0.
LIMITED TWO YEAR WARRANTY ON ELECTRIC START RIDING EQUIPMENT
For two (2) years from the date of purchase, ff this riding equipment is maintained, lubricated and tuned up according to the
instructions in the owner's manueJ,Sears will repair or replace, free of charge, any parts found to be defective in material or
workmanship.
This Warranty does not cover:
+ Expendableitems which become worn during normal use, such as blades, spark plugs, air cleaners and belts.
• "13rereplacement or repair caused by puncturesfrom outside objects, such as nails, thorns,stumps, or glass.
•Repairs necessary because of operator abuse,negligence, improperstorage or accidentor thefailure to maintain the
equipment according tothe instructionscontained inthe owner's manual.
• Riding equipment usedfor commercial or rentalpurposes.
LIMITED 90 DAY WARRANTY ON BATTERY
For90 days from date of purchase, if any batteryincluded with this riding equipment proves defective in material or workmanship
and our testing determines the battery willnot hold a charge, Sears willreplace the batteryat no charge.
WARRANTY SERVICE iS AVAILABLE BY RETURNING THE RIDING EQUIPMENT TO THE NEAREST SEARS SERVICE
CENTER/DEPARTMENT INTHE UNITED STATES.
This Warranty g!vesyou specific legaJdghts,and you may also haveother rights which may vary from stateto state.
SEARS, ROEBUCK AND CO., D/731CR,W, SEARS TOWER, CHICAGO, iLLINOIS 60684
3

TABLE OF
SAFETY RULES ........................................................ ;...2
PRODUCT SPECIFICATIONS ....................................... 3
CUSTOMER RESPONSIBILITIES ..................... 3, !4-1"/'
WAR RANTY ................................................................... 3
TABLE OF CONTENTS ................................................. 4
INDEX ........................................................... ;................. 4
TRACTOR ACCESSORIES ........................................... 5
ASSEMBLY ................................................................ 7@
CONTENTS
OPERATION ............................................................ 10-13
MAINTENANCE SCHEDULE ...................................... 14
SERVICE AND ADJUSTMENTS ............................ 18-23
STORAGE .................................................................... 24
TROUBLESHOOTING ....... ,.................................... 25-26
REPAIR PARTS -TRACTOR ................................. 28-43
REPAIR PARTS - ENGINE ..................................... 44-48
PARTS ORDERING/SERVICE ................... BACK PAGE
INDEX
A
Accessories ............................................ 5
Adjustments=
Brake ........... i............ i.................. 20
Carburetor. .................................. 23
Mower
Front-To-Back ........................ t9
Side-To-Side .......................... 19
Throttle Control Cable ...... :.......... 23
Air Filter, Engine ................................. t7
Air Screen, Engine ............................. t7
Assembly ........................................... 7-9
B
Battery:
Charging ........................................ 8
Cleaning ...................................... ! 6
installation ..................................... 9
Levels ....................................... 8,16
Preparation .................................... 8
Starting with Weak Battery .......... 21
Storage ........................................ 24
Terminals .................................... 16
BeR:Motion Drive
Removal/Replacement ........... 20
Mower Blade Drive
Remova!/Replacement ........... 20
Blade:
Sharpening .................................. 15
Replacement ............................... 15
Brake Adjustment ............................... 20
C
Carburetor Adjustment ....................... 24
Controls, Tractor ................................. t0
Customer Responsibilities ............. 14-17
Engine:
Air Filter ................................... 17
Air Filter Foam Pre-Cleaner .... 17
Air Screen, Engine .................. 17
Battery ..................................... !6
Cooling Fins, Engine ............... t7
Engine Oil ................................ 16
Fuel Fitter ................................ 17
Spark Piugs ............................. 17
Tractor:
Blade ....................................... t 5
Lubrication Chart ..................... 14
Maintenance Schedule ............ 14
Tire Care .............. ........... 8,15,21
Cutting Height, Mower ........................ 11
E
Electrical:
Interlocks and Relays .................. 22
Schematic ................................... 27
Wiring Diagram .......... :................. 28
Engine:
Air Filter ....................................... t7
Air Filter Foam Pre:Cteaner ........ 17
Air Screen ................................... !7
Cooling Fins, Engine ................... 17
Oil Change .................................. t6
Oil Level ................................. 12,16
Oil Type ....................................... 16
Preparation .................................. 12
Repair Parts ........................... 4448
Starting ........................................ 13
Storage ........................................ 24
F
Filter:
Air Filter ....................................... 17
Air Filter Foam Pre-Cleaner ........ t7
Fuel ............................................. 17
Fuel:Type ............................................ 12
Storage ........................................ 24
Fuse :................................................... 22
H
Hood Removal/lnstaUation .................. 22
L
Leveling Mower Deck ......................... t9
Lubrication:
Chart ............................................ 14
M
Maintenance Schedule ........ _............. 14
Mower:
Adjustment, Front-to-Back ........... 19
Adjustment, Side-to-Side ............. t9
Blade Sharpening..: ..................... 15
Blade Replacement ..................... 15
Cutting Height ........... ;;................. tl
Installation ...................... ;............ 18
Operation ..................................... 12
Removal ....... ::............................. t8
Mowing Tips ....................................... 13
Muffler ................................................. !7
=Spark Arrester ............. t-.-......... 3,38
O
Oil: Cold Weather Conditions ,..., I2,16
Engine ............................. ;........... t6
Storage ........................................ 24
Operation ...................................... 10-t 3
Operating Mower ................................ 12
Options:
Accessories ................................... 5
Spark Arrester .......................... 3,38
P
Parking Brake ................................ 10-! t
Parts Bag .............................................. €
Parts, Replacement/Repair ........... 28-43
Product Specifications ........................... 3
R
Repair Parts .................................. 28-43
S
Safety Rules ......................................... 2
Seat ...................................................... 8
Service and Adjustments .............. t8-23
Carburetor ................................... 23
Fuse ............................................ 22
Hood Removal/Installation .......... 22
Motion Drive Belt
Removal/Replacement ........... 20
Mower B!ade Drive Belt
Removal/Replacement ........... 20
Mower Adjustment
Front- to-Back ......................... 19
Side-to-Side ............................ 19
Mower Removal .......................... 18
Tire Care ............................. 8,15,21
Slope Guide Sheet .... :........................ 51
Spark Plugs ........................................ 17
Specifications ....................................... 3
Starting the Engine ........................ 12-13
Steering Wheel ................................ 7,21
Stopping the Tractor ........................... 11
Storage ............................................... 24
T
Throttle Control Cable
Adjustment .................................. 23
Tires ................................................... 8,t5,2!
Trouble Shooting Chart .................. 25-26
Transaxle:
Repair Parts ........................... 4243
W
Warranty ............................................... 3
Wiring Diagram ................................... 28
Wiring Schematic ............................... 28
4

ACCESSORIES AND ATTAC TS
These accessories and attachments were available when the unit was purchased. They are also available at most Sears retail outlets,
catalog and service centers. Most Sears stores can order these items for you when you provide the model number of your tractor.
MAfNTENANCE
ENGINE
PLUG AIR FILTER
MUFFLER GAS CAN ENGINE OiL STABILIZER BLADES BELTS
PERFORMANCE
Sears offers a wide variety of attachments that fit your vehicle. Many of these are listed below with brief explanations of how they can help
you. This list was current at the time of publication; however, itmay change in future years -more attachments may be added, changes may
be made inthese attachments, or some may no longer be available orfit your model. Contact your nearest Sears store for the accessories
and attachments that ate avaltable for your unit.
Most of these attachments do not require additional hitches or conversion kits (those that do are indicated) and are designed for easy
attaching and detaching,
PERMANEX BAGGER lets you collect grass clippings and
leaves for ahealthier, nearer looking lawn. Two Permanex
containers hold 30-gallon plastic bags.
LAWN SWEEPERS let you collect grass clippings and leaves.
LAWN VACS for powerful collection of heavy grass clippings and
leaves. Wand attachment to pick up debris in hard-to-reach
places.
CARTS make hauling easy. Variety of sizes available.
ROLLER for smoother lawn surface. 36-inch wide, 18-inch
diameterwater-tight drum holds upto390 Ibs.ofweight. Rounded
edges prevent harm to turf. Adjustable scraper automatically
cleans drum.
SPREADER/SEEDERS make seeding, fertilizing, and weed
kiUing easy. Broadcast spreaders are also usefut for granular
de-icers and sand.
CORING AERATOR takes small plugs out of soil to allow mois-
ture and nutrients to reach grass roots. 36-inch swath. 24
hardened steel coring tips. 150 lb. capacity weight tray.
AERATOR promotes deep root growth for a healthy lawn. Ta-
pered 2.5-inch steel spikes mounted on 10-inch diameter discs
puncture holes in soil at close intervals to let moisture soak in.
Steel weight tray for increased penetration.
MULCH RAKE/DETHATCHER loosens soil and flips thatch and
matted leaves to lawn surface for easy pickup. Twenty spring tins
teeth. Usefultopreparebareareasforseeding. Availableforfront
or rear mounting.
SPRAYERS use 12-volt DC electric motor that connects to the
tractor battery or other 12wolt source. Includes booms for
automatic spraying when pulling, and hand held wand for spot
spraying. Wand has adjustable spray pattern. For applying
herbicides, insecticides, fungicides, and liquid fertilizers.
SNOW BLADE for snow removal only. 14-inch high, 42-inch
wide blade clears 38-inch path when angled left or right. Raises,
lowers with side lever. Adjustable skids; replaceable, reversible
scraper bar. (Use with tire chains, wheel weights, or rear drawbar
weight.)
SNOWTHROWER has 40-inch swath. Drum-type auger handles
powdery and wet/heavy snow. Mounts easily with simple pin
arrangement. Discharge chute adjusts from tractor seat. 6-inch
diameter spout discharges snow ! 0 to 50 feet. Lift controlled at
tractor seat. (Use with chains, wheel weights, or rear drawbar
weight.)
TIRE CHAINS are heavy duty; closely spaced extra-large cross
links give smooth ride, outstanding traction.
WHEEL WEIGHTS for rear wheels provide needed traction for
snow removal or dozing heavy materials, in pairs. (30 ibs. each.)
TRACTOR CAB has heavy duty vinyl fabric over tubular steel
frame, ABS plastic top; clear plastic windshield offers 360 degree
visibility. Hinged metal doors with catch. Keeps operator warm
and dry. Remove vinyl and windshields for use as sun protector
in summer. (Catalog only.)
Optiona! accessories for tractor cab: tinted/tempered solid
safety glass windshield with hand operated wiper; 12-volt amber
caution light for mounting on cab top, (Catalog only.)
TRACTOR COVER protects tractor from weather. Made of
Evolution 3 fabric (water-repellent, extremely breathable, light
weight, soft, non-abrasive, pliable in all temperatures, durable,
stain/tear/puncture resistant, will not shrink or stretch.) (Catalog
only.)

CONTENTS OF HARDWARE PACK
i
i
i
i
Parts Bag contents shown full size
(2) Sheet
Metal
Screws
#10-16 x 1/2
(1) 2-3/8" Dia. Washer (1) Locknut 3/8-24
(1) Shoulder Bolt 5/t8-18
(1) Hex Bolt 1/2-13 x 1
(1) Lock Washer 1/2
(1) Washer 17/32 x 1-3/!6 x !2 Ga,
(2) Hex Bolts 1/4 - 20 x 3/4 (2) Hex Nuts !/4- 20
(2) Lock Washers 1/4
(2) Washers 9/32 x 5/8 x 16 Ga.
6
Parts packed separately in carton
Seat O
Battery acid
Battery
j-
!
1
Owner's Manual
Steering
Boot
Parts Bag
Parts bag contents not shown full size
__ Steering
Wheet
Steering Wheel ansert
Adapter
G
Steering
Bushing
(2) Keys
15°Slope Sheet B_tter3, Caps
and Instructions

, . ,,.
ASSE BLY
TOOLS REQUIRED FOR ASSEMBLY
Asocket wrench set willmake assembly easier, Standard
wrench sizes are listed.
(1) 5/!6" wrench
(2) 7/t6" wrenches
(!) t/2" wrench
Tire pressure gauge
Screwdriver
Utility knife
(1) 9/16" wrench
When right and left hand is mentioned in this manual, it
means when you are in the operating position (seated
behind the steering wheel).
TO REMOVE UNiT FROM CARTON
UNPACK CARTON
° Remove all accessible loose parts and parts cartons
from carton (See page 6).
• Cut along dotted lines on carton, from top to bottom, all
four corners of carton and lay panels fiat.
•Check for any additional loose parts or cartons and
remove.
BEFORE ROLLING UNiT OFF SKID
ATTACH STEERING WHEEL (See Fig. 1)
* Slide the steering bushing over the steering shaft.
=Raise steering shaft forward until screw holes in dash
tine up with steering bushing. Install two (2) sheet
metal screws and tighten securely.
oPosition steering boot over steering shaft.
*Place tabs of steering boot over slots in dash and push
down to secure.
° Slide steering wheel adapter onto upper steed ng shaft.
oPosition front wheels of the tractor so they are pointing
straight forward.
, Position steering wheel so cross bars are horizontal
(teftto right) and slide onto adapter.
oAssembte large fiat washer and 3/8-24 hex locknut and
tighten securely.
Snap insert into center of steering wheel,
*Remove protective plastic from tractor hood and grill.
IMPORTANT; CHECK FOR AND REMOVE ANY
STAPLES iN SKiD THAT MAY PUNCTURE TIRES WHERE
UNIT IS TO ROLL OFF SKID,
(See Fig,6)
"Raise attachment liftlever to itshighest position.
o Release parking brake by depressing clutch/brake
pedal.
, Place gearshift tever in "NEUTRAL" position.
o Roll unit backwards off skid.
o Remove banding holding discharge gua[d up against
tractor.
INSERT
3]8-24 HE)( LOCKNUT
2-3/8" DIA. WASHER
STEERING
STEERING
BUSHING
STEERING
BOOT
STEERING SHAFT
(ASSEMBLY POSITION)
STEERING SHAFT
=SoHIPPING
SIT|ON)
FIG. 1
7

ASSEMBLY
HOW TO SET UP YOUR TRACTOR
PREPARE BATTERY (See Fig. 2}
CAUTBON: Wear eye and face sh|etd.
Wash hands or clothing Immedlately if
accidentalmy tncontact with battery acid,
Do not smoke. Fumes from charged
battery acid are explosive,
Read the instructions Included with the
batteryvent caps. Alwayswear gloves,
clothing and goggles to protect your
hands, skln and eyes.
Your unit has a battery chargingsystem which issufficient
for normal use. However, periodic charging of the battery
with an automotive charger will extend its life.
, See instructions packed with vent caps in parts bag.
• Fill battery with acid. Fill each cell until it reaches the
bottom of the vent wells. Do not overfill.
Allow battery to stand and settle for at least thirty
minutes. After standing, check the level of acid. If
below the vent wells, add more acid until the correct
level is reached.
While battery is standing (after adding acid) and later, while
battery isbeing charged, continue with assembly of unit.
iMPORTANT: TO MAXIMIZE THE LIFE OF YOUR
BATTERY, IT IS NECESSARY THAT THE BATTERY BE
CHARGED BEFORE USE. FAILURE TO CHARGE
BATTERY CAN RESULT IN A SHORTENED BATTERY
LIFE.
• Charge battery at a rate of 6 amperes for ! hour. Use
a 12volt battery charger. Observe at!safety precautions
required for battery charging.
oCheck the acid level after the battery ischarged, ifthe
acid has fallen below the correct level, add distilled or
iron free water.
= install the vent caps to cover the vent wells. Wash the
top of the battery with water to remove any acid, then
wipe dry.
" Check battery case for Beakageto make sure that no
damage has occurred in handling.
,Dispose of excess battery acid. Neutralize acid for
disposal by adding it to four inches of water in a five
gallon plastic container. Stir with a wooden or plastic
paddle while adding baking soda untit the addition of
more soda causes no more foaming.
o Follow instructions on how to install battery.
iNSTALL SEAT (See Fig. 3)
Adjust seat before tightening adjustment bolt.
, Remove cardboard packing on seat pan.
= Place seat on pan and assemble shoulder bolt.
oAssemble adjustment bolt, tockwasherand fiat washer
toosely. Do not tighten.
°Tighten shoulder bolt securely.
- Lower seat into Operating position and sit on seat.
•Slide seat until a comfortable position is reached which
allowsyou to press clutch/brake pedal all the way down
(See Fig. 6).
•Get off seat without moving its adjusted position.
• Raise seat and tighten adjustment bolt securely.
SHOULDER
BOLT
FLAT WASHER
ADJUSTMENT ,LOCK WASHER
BOLT
FtG. 3
CHECK TIRE PRESSURE
The tires on your unit were overinflated at the factory for
shipping purposes. Correct tire pressure is important for
best cutting performance.
*Reduce tire pressure to PSi shown in "PRODUCT
SPECIFiCATiONS" on page 3 of this manual.
CHECK DECK LEVELNESS
For best cutting _esults, mower housing should be properly
leveled. See TO LEVEL MOWER HOUSING" in the
Service and Adjustments section of this manual.
CHECK FOR PROPER POSiTiON OF ALL
BELTS
See the figures that are shown for replacing motion and
mower blade drive belts in the Service and Adjustments
section of this manual. Verify that the belts are routed
correctly.
CHECK BRAKE: SYSTEM
After you learn how to operate your tractor, check to see
that the,,brake is properly adjusted. See "TO ADJUST
BRAKE in the Service and Adjustments section of this
manual
FiG° 28

ASSEMBLY
iNSTALL BATTERY (See Figs. 4 & 5)
o
o
CAUTION: Do not short battery termi-
nals. Before Installing battery, remove
metat bracelets, wristwatch bands,
rings, etc,
Positive termina_ must be connected
first to prevent sparking from acciden-
tal grounding.
Lift seat to raised position.
Open battery box door.
Lower battery into battery box with battery terminals
toward front of unit.
° Be sure battery drain tube is attached to battery box,
• First connect RED battery cabfe to positive (+) battery
terminal with hex bolt, flat washer, lockwasher and he×
nut as shown. Tighten securely.
Connect BLACK grounding cable to negative (°) bat-
tery ,erminal with remaining hex bolt, flat washer, lock
washer and he× nut. Tighten securely.
• Close battery box door.
Open battery box door for:
, Inspection for secure connections (to tighten hard-
ware).
o inspection for corrosion.
, Testing battery.
•Jumping (if required).
,Periodic charging.
BATTERY
BOX DOOR
POSITIVE NEGATtVI_
(RED) CABLE (BLACK) CABLE
FLAT
WASHER
HE×
BO_
FIGo 4
BATTERY
VENT CAPS
FiG. 5
JCHECKLIST
BEFORE YOU OPERATE AND ENJOY YOUR NEW
TRACTOR, WE WISH TOASSURE THAT YOU RECEIVE
THE BEST PERFORMANCEAND SATISFACTION FROM
THIS QLIALITY PRODUCT.
PLEASE REVIEW THE FOLLOWING CHECKLIST:
/All assembly instructions have been completed.
,! No remaining bose parts in carton.
J Battery is properly prepared and charged. (Minimum
1 hour at 6 amps).
Seat is adjusted comfortably and tightened securely.
€" AI! tires are properly inflated. (For shipping purposes,
the tires were over-inflated at the factory).
•/Be sure mower deck is properly leveled side-to-side/
front-to-rear for best cutting results. (Tires must be
properly inflated for bveiing).
_" Check mower and drive belts, Be sure they are routed
properly around pulleys and inside all belt keepers.
€" Check wiring_ See that all connections are still secure
and wires are properly clamped.
WHILE LEARNING HO W TO USE YOUR TRACTOR, PAY
EXTRA A TTENTION TO THE FOLLOWING IMPORTANT
ITEMS:
J" Engine oil is at proper level.
V' Fuel tank is filled with fresh, clean, regular unleaded
gasoline.
,f Become familiar with all controls -their location and
function. Operate them before you start the engine.
_f Be sure brake system is in safe operating condition.
9

OPERATION
KNOW YOUR TRACTOR
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR
Compare the illustrations with your tractor tofamiliarize yourself with the locations of various controls and adjustments. Save
this manual for future reference.
ATTACHMENT
CLUTCH LEVER IGNITION LIFT LEVER
SWITCH PLUNGER
LIGHT SWITCH \ATTACHMENT
LIFT LEVER
,THROTTLFJCHOKE
CONTROL
CLUTCH!BRAKE
[J
MOWER DECK
HEIGHT ADJUSTMENT
POSITIONS
PARKING
GEARSHIFT
LEVER
FiG. 6
Sears tractors conform to the safety standards of the American National Standards Institute.
ATTACHMENT CLUTCH LEVER: Used to engage the
mower blades, or other attachments mounted to your
tractor.
LIGHT SWITCH: Turns the headlights on and off.
THROTTLE/CHOKE CONTROL: Used for starting and
controlling engine speed.
CLUTCH/BRAKE PEDAL: Used for declutching and
braking the tractor and starting the engine.
PARKING BRAKE: Locks clutch/brake pedal into the
brake position,
GEARSHIFT LEVER: Selects the speed and direction of
tractbr.
ATTACHMENT LiFT LEVER: Used to raise, iower, and
adjust the mower deck or other attachments mounted to
your tractor,
UFT LEVER PLUNGER: Used to release attachment lift
lever ,whenchanging its position.
IGNiTiON SWITCH: Used for starting and stopping the
engine.
10

OPERATION
The operation of any tractor can result in foreign objects thrown into the eyes, which can
result in severe eye damage. Always wear safety glasses or eye shields while operating
your tractor or performing any adjustments or repairs. We recommend wide vision safety
mask for over the spectacles or standard safety glasses, available at Sears Retail or
CataJog stores,
HOW TO USE YOUR TRACTOR
TO SET PARKING BRAKE (See Fig. 7)
• Depress clutch/brake pedat into full "BRAKE" position
and hold.
-Place parking brake lever in "ENGAGED" position and
release pressure from clutch/brake pedal. Pedal should
remain in "BRAKE" position. Make sure parking brake
will hold vehicle secure,
IGNITION
THROTTLF_
CHOKE
CONTROL'
LEVER
PARKING
8RAKE
"ENGAGED"
POSITION
GEAR-
SHIFT
LEVER
FiG. 7
STOPPING (See Fig, 7)
MOWER BLADES-
• Move attachment clutch lever to "DISENGAGED" po-
sition.
GROUND DRIVE -
•Depress clutch/brake pedal intofull "BRAKE" position.
• Move gearshift lever to "NEUTRAL" position.
ENGINE -
o Move throttle control to "SLOW" position.
, Turn ignition key to "OFF" position and remove key.
Always remove key when leaving vehicle to prevent
unauthorized use.
• Never use choke to stop engine.
NOTE: Under certain conditions when unit is standing idle
with the engine running, hot engine exhaust gases may
cause "browning" of grass. To eliminate this possibility,
always stop engine when stopping unit on grass areas.
CAUTiO N: Always stop unit cornpletely,
as described above, before leaving theoperator's position; to empty grass _
catcher, etc, _.J
TO USE THROTTLE CONTROL (See Fig. 7)
Always operate engine at full throttle.
oOperating engine at less than full throttle reduces the
battery charging rate and the engine cooEing air flow.
•Full throttle offers the best bagging and mower per-
formance.
TO MOVE FORWARD AND BACKWARD (See
Fig. 6)
The direction and speed of movement is controlled by the
gearshift lever.
, Start tractor with clutch/brake pedal depressed and
gearshift lever in "NEUTRAL" position.
• Move gearshift lever to desired position.
• Slowly release clutch/brake pedal to start movement.
iMPORTANT: BRING TRACTOR TO A COMPLETE STOP
BEFORE SHIFTING OR CHANGING GEARS. FAILURE
TO DO SO WILL SHORTEN THE USEFUL LIFE OF YOUR
TRANSAXLE,
TO ADJUST MOWER CUTTING HEIGHT (See
FL.6)
The position of the attachment lift lever determines the
cutting height.
° Grasp lift lever.
• Press plunger with thumb and move lever to desired
position.
Thecutting height range is approximately 1-t/2to 4". The
heights are measured from the ground to the blade tip with
the engine not running. These heights are approximate
and may vary depending upon soil conditions, height of
grass and types of grass being mowed.
o The average lawn should be cut approximately 2-1/2
inches during the coot season and over 3 inches during
hot months. For healthier and better looking lawns,
mow often and after moderate growth.
o For best cutting performance, grass over 8 inches in
height should be mowed twice. Make the first cut
relatively high; the seco_c__odes_d height.

H_
OPERATION
TO OPERATE MOWER (See Fig. 8)
Your unit is equipped with an operator presence sensing
switch. Any attempt by the operator to leave the seat with
the engine running and the attachment clutch engaged will
shut off the engine,
,Select desired height of cut.
oEngage mower by slowly moving attachment clutch
lever to "ENGAGED" position.
• TO STOP MOWER - Move attachment clutch lever to
"DISENGAGED" position.
CAUTION: Do not operate the mower
without either the entire grass catcher,
on mowers so equipped, or the dis-
charge guard in place.
ATTACHMENT
LIFT LEVER
HiGH POSITION
LOW
POSiTiON
DISCHARGE GUARD
FIG. 8
TO OPERATE ON HILLS
1_ CAUTmON: Do not drive up or down
hi{Is with slopes greater than 15° and
do not drive across any slope.
Choose the slowest speed before starting up or down
hills.
, Avoid stopping or changing speed on hills,
o If slowing is necessary, move throttle control aeverto
slower position,
If stopping is absolutely necessary, push clutch/brake
pedal quickty to brake position and engage parking
brake.
Move gearshift Dover,to1st gear and be sure you have
allowed room for trac,or to rol! slightly as you restart
movement.
To restart movement, slowly release parking brake and
clutch/brake pedal.
Make alSturns slowty.
TO TRANSPOF_T
o Raise attachment liftcontrol to highest position.
- When pushing or towing your unit, be sure gearshift
lever is in "NEUTRAL" position.
• Do not push or tow unit at more than five (5) MPH.
BEFORE STARTING THE ENGINE
CHECK ENGINE OIL LEVEL (See Fig, 13)
o The engine in your unit has been shipped, from the
factory, already filled with summer weight oit.
*Check engine oil with unit on tevet ground.
,Remove oil fill dipstick and wipe clean, replace and
screw cap tight, wait for a few seconds, remove and
read oil level, if necessary, add oil until "FULL" mark
on dipstick is reached. Do not overfill
oFor cold weather operation you should change oil for
easier starting (see "OIL VISCOSITY CHART" in the
Customer Responsibilities section of this manual).
oTo change engine oil, see the Customer Responsibili-
ties section in this manuat.
ADD GASOUNE
,Fill fue! tank. Use fresh, clean, regular unleaded
gasoline. (Use of leaded gasoline will increase carbon
and lead oxide deposits and reduce vatve life).
IMPORTANT: WHEN OPERATING IN TEMPERATURES
BELOW 32°F(0°C), USE FRESH, CLEAN WINTER GRADE
GASOLINE TO HELP INSURE GOOD COLD WEATHER
STARTING.
WARNING: Experience indicates that alcohol blended
fuels (called gasohol or using ethanol or methanol) can
attract moisture which leads to separation and formation of
acids during storage. Acidic gas can damage the fuel
system of _qnengine while in storage. To avoid engine
problems, the fuel system should be emptied before stor-
age of 30 days or longer. Drain the gas tank, start the
engine and let itrun unlit the fue_ lines and carburetor are
empty. Use fresh fuel next season, See Storage instruc-
tions for additional information, Never use engine er
carburetor cleaner products in the fuel tank or permanent
damage may occur.
CAUTION: FitJto bottom of gas tank
fiBter neck, Do not overfill, Wipe off any
spilJed oil or fuel. Do not store, spil! or
use gasoline near an open flame°
12

H
E
OPERATIO
TO START ENGINE (See Fig. 7}
When starting engine for the first time or ff engine has
run out of fuel, it will take extra cranking time to move
fuel from the tank to the engine,
,Depress the clutch/brake pedal and set the parking
brake.
• Place gearshift Jever in "NEUTRAL" position.
,Move attachment cfutch to "DISENGAGED" position,
,Move throttle control lever to "CHOKE" position for
cold engine start, For warm engine start, move
throttle controt to "FAST" position.
.Turn ignition key clockwise to "START" position and
release key as soon as engine starts. Do not run
starter continuously for more than fifteen seconds
per minute, if engine does not start after several
attempts, move throttle control to "FAST" position,
wait a few minutes and try again.
,When engine starts, move throttle control to desired
position.
oAllow engine to warm up for a few minutes before
engaging drive or attachment clutch.
NOTE; If at a high altitude (above 3000 feet) or in cold
temperatures (below 32° F), the carburetor fuel mixture
may need to be adjusted for best engine performance,
See "TO ADJUST CARBURETOR" in the Service and
Adjustments section of this manual.
MOWING TIPS
.Tire chains cannot be used when the mower hous-
ing is attached to unit.
* Mower should be properly leveled for best mowing
tt
performance. See TO LEVEL MOWER HOUSING
in the Service and Adjustments section of this
manual.
•Use the runner on the right hand side of mower as
a guide. The blade cuts approximately an inch
outside the runner (See Fig. 8).
o The left hand side of mower should be used for trim-
ming.
Drive so that clippings are discharged onto the area
that has been cut. Have the cut area to the right of
the machine, This will result in a more even distri-
bution of clippings and more uniform cutting.
When mowing large areas, start by turning to the
right so that clippings will discharge away from
shrubs, fences, driveways, etc, After one or two
rounds, mow in the opposite direction making left
hand turns until finished (See Fig. 9).
FIG. 9
. If grass is extremely tall, it should be mowed twice
to reduce load and possible fire hazard from dried
clippings, Make first cut relatively high; the second
to the desired height.
• Do not mow grass when it is wet. Wet grass will
plug mower and leave undesirable clumps. Allow
grass to dry before mowing,
•Always operate engine at full throttle when mowing
to assure better mowing performance and proper
discharge of material. Regulate ground speed by
selecting a low enough gear to give the mower
cutting performance as welt as the quality of cut
desired.
• When operating attachments, select a ground speed
that will suit the terrain and give best performance of
the attachment being used.
!3

-i
CUSTO E RESPONS L lee
MAINTENANCE SCHEDULE
FILL IN DATES
AS YOU COMPLETE
REGULAR SERVICE SERVICE DATES
Check Brake Operation
Check Tire Pressure
Check for Loose Fasteners
Sharpen!Replace Mower Blades
Lubrication Chart
Check Battery Level/Recharge
Clean Battery and Terminals
Check Transmission Cooling
Adjust Blade Belt(s) Tension
Adjust Motion Drive Belt(s) Tension
Check Engine Oil Level
Change Engine Oil
Clean Air FJ_ter
Clean Air Screen
inspect Muffler/Spark Arrester
Replace Oil Filter ({f equipped)
Clean Engine Cooling Fins
Replace Spark Ptug
Reptace Air Filter Paper Cartridge
Replace Fuei Filter
- Change more often when operating under a hear
2-Service more o_en when operating tn ditty or dusty conditions, 8- if equipped withoit fiiter, change oil avery 50 hours.
4 - Replace blades more oftenwhen mowing in s_ndysoil,
GENERAL RE COIVIMENDATIONS
The warranty on this vehicle does not cover items that have
been subjected to operator abuse or negligence. To
receive full .value from the warranty, operator must main-
tain unit as instructed in this manual.
Some adjustments will need to be made periodicaity to
properly maintain you_ unit.
All adjustments in the Service and Adjustments section of
this manual should be checked at least once each season.
Once a year you should replace the spark plug, clean
or replace air filter, and check blades and belts for
wear. A new spark ptug and clean air filter assure
proper air-fuel mixture and help your engine run better
and last longer,
LUBRiCATiON CHART
(_) SPINDLE ZERK _PiNDLEZERK(_)
(if _quipped) {If equipped)
®CLUTCH PIVOT
BEFORE EACH USE
oCheck engine oil level.
• Check brake operation.
, Checktire pressure.
. Check for loose fasteners.
"14
(_ SAE 30 OR 10W30 MOTOR O_L APJ * SG
(_) GENERAL PURPOSE GREASE
{_) RE,FER TO CUSTOMER RESPONS_BZUTtE$ "ENGINE" SECTION
IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS
WHICH HAVE SPECIAL NYLON BEARINGS, VISCOUS LUBRt_
CANTS WILL ATTRACT DUST AND DIRT THAT W_LL SHORTEN
THE LIFE OF THE SELF-LUBRICATING BEARINGS. iF YOU
FEEL THEY MUST BE LUBRICATED, USE ONLY A DRY, POW-
DERED GRAPHITE TYPE LUBRICANT SPARINGLY.

CUSTOM ESPONSI LITIES
TRACTOR
Always observe safety rules when performing any mainte-
nance.
BRAKE OPERATION
If unit requires more than six (6) feet stopping distance at
high speed in highest gear, than brake must be adjusted.
(See TO ADJUST BRAKE in Service and Adjustments
section of this manual).
TIRES
. Maintain proper air pressure in alt tires (See "PROD-
UCT SPECiFiCATiONS" on page 3 of this manual}.
° Keep tires free ofgasoline, oil, or insect control chemi-
cals which can harm rubber.
o Avoid stumps, stones, deep ruts, sharp objects and
other hazards that may cause tire damage.
BLADE CARE
For best results mower blades must be kept sharp. The
blades can be sharpened with a file or on a grinding wheel,
We suggest they be sharpened or replaced after every 25
hours of mowing. Check blades more often if mowing in
sandy conditions.
• Do not attempt to sharpen blades while they are onthe
mower.
* Replace bent or damaged blades.
BLADE REMOVAL (See Fig. 10)
*Raise mower to highest position to allow access to
blades.
•Remove hex bolt, lockwasher and fiat washer securing
blade.
• Install new or resharpened blade with trailing edge up
towards deck as shown.
•Reassemble hex bolt, lock washer and flat washer in
exact order as shown,
Tighten bolt securely (30-35 Ft, Lbs. torque).
iMPORTANT: BLADE BOLT tS GRADE 8 HEAT TREATED.
BLADE _'_ _ %_ MANDREL
"_ H_ BOLTIG_D_8)*
*A GRADE 8 HEAT TREATED BOLT CAN BE
iDENTIFIED BY SiX LINES ON THE BOLT HI_,D.
FIG. 10
TO SHARPEN BLADE (See Fig. 11)
Care should be taken to keep the blade balanced. An
unbalanced blade will cause excessive vibration and even-
tual damage to mower and engine,
* The blade can be sharpened with a file or on a grinding
wheel, Do not attempt to sharpen while on the mower.
o To check blade balance, you will need a 5/8" diameter
steel bolt, pin, or a cone balancer. (When using a cone
balancer, foltow the instructions supplied with bar
ancer).
,Slide blade on to an unthreaded portion ofthe steel bolt
or pin and hold the bolt or pin parallel with the ground.
If blade is balanced, it should remain in a horizontal
position. If either end of the blade moves downward,
sharpen the heavy end until the blade is balanced.
NOTE: Do not use a nait for balancing blade. The lobes of
the center hole may appear to be centered, but are not.
CENTER HOLE
5/8" BOLT
OR PIN
BLADE
FIG, 11
1S

CUSTO E RESPO Sl iLITIES
BATTERY (See Fig. 12)
Your unit has a battery charging system which is sufficient
for normal use. However, periodic charging of the battery
with an automotive charger wilt extend it's life.
•.Acid solution tevel in each battery ceil should be even
with bottoms of vent wells. Add only distilled or iron free
water if necessary. Do not overfill.
CUT AWAY VIEW
CELL ACID
LEVEL
FroG°i 2
, Keep battery and terminals clean.
, Keep battery bo!ts tight.
oKeep vent caps tight and smal! vent holes incaps open,
• Recharge at 8 amperes for 1 hour,
TO CLEAN BATTERY AND TERMINALS -
Corrosion and dirt on the battery and terminals can cause
the battery to "leak" power.
-Remove terminal guard.
•Disconnect BLACK battery cable first then RED bat-
tery cable and remove battery from tractor.
° Wash battery with solution of four tablespoons of
baking soda to one gallon of water. Be carefut not to get
the soda solution into the ceils.
• Rinse the battery with plain water and dry.
• Clean terminaJs and battery cable ends with wire brush
until bright.
, Coat terminals with grease or petroleum jelly.
° Reinstall battery (See "INSTALL BATTERY" in the
Assembly section of this manual).
V-BELTS
Check V-belts for deterioration and wear after t00 hours
and replace if necessary. The belts are not adjustable.
Replace belts if they begin to slip from wear.
TRANSAXLE COOLING
Keep transaxle free from build-up of dirt and chaff which
can restrict cooJing.
ENGINE
LUBRICATION
Change the oil after the first two hours of operation and
every 25 hours thereafter or at least once a year if the
tractor is not used for 25 hours in one year.
Check the crankcase oil level before starting the engine
and after each eight (8) hours of continuous use. Add SAE
30W motor oi{ or equalivent, Tighten oit fill cap/dipstick
securely each time you check the oil level, SAE 5W-30
motor oil may be used to make starting easier in areas
where temperature is consistently 32° F or Jower.
TO CHANGE ENGINE OiL (See Fig, !3)
Determine temperature range expected before oil change.
All oil must meet API service classification SG,
o 8e sure vehicle is on level surface.
- Oil will drain more freely when warm.
,Catch oil in a suitable container.
* Remove oil filf dipstick. Be careful not to allow dirt to
enter the engine when changing oil.
oRemove drain plug.
, After oil has drained completely, replace oil drain plug
and tighten securely.
o Refill engine with oi! through oil fill dipstick tube. Pour
slowfy. Do not overfil!. For approximate capacity see
Product Specifications on page 3 of this manual.
, Use £auge on oil fill dipstick for checking level. Be sure
dipstick cap istightened securely for accurate reading.
Keep oil at "FULL" line on dipstick.
SAE V_SCOStTY GRADES
F_G. 13
16

CUSTOM ES 0 S! IL ES
AIR FILTER FOAM PRE-CLEANER (See Fig.
14)
Your engine will not run propedy and may be damaged by
using a ditty air filter. Clean the foam pre+cteaner element
after every 25 hours of operation, more often ifused in very
dusty, ditty conditions.
- Remove knob and cover.
-Remove cartridge nut and replace cartridge.
° ReassembLe and tighten securely.
NOTE: Do not attempt to clean or oil the paper cartridge.
Replace paper cartridge once a year or after every 100
hours of operation, more often if used in very dusty, dirty
conditions,
,Wash foam pre+cleaner in _iquid detergent and water,
•Wrap foam pre+cleaner in cloth and squeeze dry.
• Lightly coat foam pre+cleaner with clean engine oil.
Squeeze in towel to remove excess oil. Do not satu-
rate.
• Install foam pre-cleaner over paper cartridge.
+ ReassembLe cover and secure with knobs.
COVER_
KNOB "="'_="+_-- T
F_Got4
AiR SCREEN (See Fig. 15)
The engine air screen must be kept free of dirt and chaff to
prevent engine damage from overheating. CLean with a
wire brush or compressed air to remove dirt and stubborn
dried gum fibers.
ENGINE. COOLING FiNS (See Fig. 15)
Remove any dust, dirt or oi+from engine cooling fins to
prevent engine damage from overheating.
°Remove oil fill dipstick and cover opening to prevent
entry of dirt.
-Remove screws from blower housing and lift housing
off engine.
+ Remove the screws securing the starter housing and
lift housing off engine.
• Use compressed air or stiff bristle brush to thoroughly
clean engine cooling fins.
°To reassemble, reverse above procedure.
8CmEW$ BLOWER HOUSING
SCREWS
STARTER
HOUSING
OIL FILL
D_PSTtCK
ENGINE COOLING RNS
SPARK
PLUG
FiG, 15
MUFFLER
Inspect and replace corroded muffler and spark arrester (if
equipped) as it coutd create a fire hazard and/or damage.
t7
SPARK PLUGS
Replace spark plugs at the beginning of each mowing
season or after every 100 hours of use, whichever comes
first. Spark plug type and gap setting is shown in "PROD-
UCT SPECIFICATIONS on page 3 of this manual.
IN-LINE FUEL FILTER (See Fig. 16)
Fuel filter should be replaced once each season. Iffuel filter
becomes clogged, obstructing fuel flow to carburetor, re-
placement is required.
° With engine coot, remove filter and plug fuel line
sections.
° Place new fuel filter in position in fuel line.
. Be sure there are no fuel line leaks and clamps are
properly positioned.
•Immediately wipe up any spilled gasoline,
FUEL
FILTER
F3G, 18
CLEANING
° Clean engine, battery, seat, finish, etc. of all foreign
matter.
,Keep finished surfaces and wheels free of all gasoline,
oil, etc+
+Protect painted surfaces with automotive type wax.
We do not recommend using a garden hose to clean your
unit unless the electrical system, muffler, air filter and
carburetor are covered to keep water out. Water in engine
can result in a shortened engine life.

SERVICE AN ADJUSTMENTS
CAUTION: BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:
i_ *Depress clutch/brake pedaa fuBly and set parking brake.
oPlace gearshift lever in "NEUTRAL" position.
• Place attachment clutch in "DKSENGAGED" position,
•Turn ignition key "OFF" and remove key.
o Make sure the bmadesand ag moving p_s have completely stopped,
o Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with
plug.
TRACTOR
TO REMOVEMOWER (See Fig. 17)
Mower will be .easier to remove from the right side of unit.
• Place attachment clutch in "DISENGAGED" position.
-Move attachment lift lever forward to lower mower to its
lowest position,
• Roll belt off engine pulley.
oDisconnect clutch rod from clutch lever by removing
retainer spring,
o Disconnect suspension arms from rear deck brackets
by removing retainer springs.
, Disconnect front links from deck by removing retainer
springs.
o Raise lift lever to raise suspension arms. Slide mower
out from under tractor.
iMPORTANT: IF AN ATTACHMENT OTHER THAN THE
MOWER tS TO BE MOUNTED TO THE TRACTOR. THE
R.H. AND L.H. SUSPENSION ARMS MUST BE REMOVED
FROM TRACTOR.
TO iNSTALL MOWER (See Fig, 17)
•Raise attachment lift lever to its highest position.
•Slide mower under tractor with discharge guard to right
side of tractor.
• Lower lift lever to its lowest position.
•Install mower in reverse order of removal instructions.
\
CLUTCH RF;TAINER
ROD SPRING
FiG. 17
ENGINE
PULLEY
i'
/
/
!8

SERVICE AND ADJUSTMENTS
TO LEVEL MOWSR HOUSING
Adjust the mower white tractor is parked on level ground or
driveway. Make sure tires are properly inflated (See
"PRODUCT SPECIFtCATLONS" on page 3). If tires are
over or under inflated, you wilt not properly adjust your
mower.
SIDE-TO-SIDE ADJUSTMENT (See Figs. 18 and 19)
• Raise attachment lift tever to its highest position.
, Measure height from bottom of deck curl to ground
aevelat front oorners of mower. Distance "A"shouLd be
the same.
oIf distance "A" needs to be changed, snap out access
hole cover on left side of tractor above footrest.
•To raise left side of mower, loosen nut "B" and tighten
nut "C".
•To lower left side of mower, loosen nut "C" and tighten
nut "B".
• When distance "A" is equal, securely tighten nuts "B"
and "C".
• Replace access hole cover.
FRONT-TO-BACK ADJUSTMENT (See Figs. 20 and 21) -
To obtain the best cutting results, the mower housing
should be adjusted so that the front is approximately 3/8" to
1/2" lower than the rear when the mower is in its highest
position,
Check adjustment on right side of tractor. Measure dis-
tance "D" at front and rear flanges of mower housing as
shown.
, To lower front of mower turn nut "E" counterclockwise
on both front links an equal number of turns.
• When distance "D" is 3/8" to 1/2" lower at front than
rear, tighten nuts "F" against trunnion on both front
links.
• To raise front of mower, loosen nut"F" from trunnion on
both front links. Turn nut "E" clockwise on both front
links an equal number of turns.
, When distance "D" is 3/8" to t/2" lower at front than
rear, retighten nut "F" against trunnion on both front
links.
iMPORTANT: WHEN ADJUSTING FRONT LINK
TRUNNtONS, ALWAYS ADJUST BOTH EQUALLY SO
MOWER WILL STAY LEVEL SIDE-TO-SIDE.
° Recheck side-to-side adjustment.
LiFTLEVER
(RAISED
POSITION)
BOTTOM
OF CURL BOTTOM
OF CURL
\
GROUND LiNE
FIG. 1B
SIDE TO SIDE ,f-"_
ADJUSTMENT _1 [,_ _ ./
TRUNNION
.__ NUT "B"
7
FRONT UNKS TRUNNION
FIG. 19 FiG. 21
19

SERVICE AND ADJUSTMENTS
TO REPLACE MOWER BLADE DRIVE BELT
(See Fig. 22}
The mower blade drive be_t may be replaced without
toois. Park the tractor on level surface. Engage parking
brake. For assistance, there is a belt installation guide
decal on the mower housing.
BELT REMOVAL o
, Place attachment clutch in "DISENGAGED" position.
° Move attachment lift tever forward to lower mower to
its lowest position.
* Roll beit off engine pulley.
Disconnect'R.H. suspension arm from rear deck
bracket by removing retainer spring.
*Work belt off both mandrel puileys and idler pulleys.
, Pull belt away from mower.
BELT INSTALLATION o
, Install new belt in reverse order of removal,
o Make sure belt is in all pulley grooves and inside all
belt guides,
PULLEYS
RETAINER
SPRING /
MANDREL
PULLEY
WITH PARKING BRAKE "ENGAGED _
JAM NUT
FIG. 23
TO REPLACE MOTION DRIVE BELT (See
Fig. 24)
Park the tractor on level area. Engage parking brake.
For assistance, there is a belt installation guide decal on
bottom side of left 'footrest.
•Remove mower (See "TO REMOVE MOWER" in this
section of this manual).
• Remove belt from stationary idler and clutching idler.
Remove belt from engine pulley.
• Roll belt over top of transaxle pulley.
, _nstall new belt by reversing above procedure.
iMPORTANT: REPLACE ONLY W_TH BELT LISTED
iN THIS MANUAL.
F_G, 22
TO ADJUST BRAKE (See Fig, 23)
Your unit is equipped with an adjustable brake system
which is mounted on the right side of the transaxle.
If unit requires more than six (6) feet stopping distance at
high speed in highest gear, then brake must be adjusted.
• Depress clutch/brake pedal and engage parking brake,
o Measure distance be,_ween brake operating arm and
nut "A" on brake rod,
ff distance is other than to!/2 ", disengage parking
brake, !oosen jam nut and turn nut "A" until distance
becomes 1-1/2", Retighten jam nut against nut "A"o
,Engage parking brake and recheck distance,
o Road test unit for proper stopping distance as stated
above, Readjust if rlec.e,ssary, Jfstopping distance is
still ...... ',_-
_,_,_ than six (6) feet in highest gear, further
maintena_ce is necessary. Contact your nearest au-
thorized service center, 20
PULLEY
FiG, 24