Craftsman 917.378431 User manual

Owner's Manual
JCRRFTSMRWI
6.75 HORSEPOWER
21" REAR DISCHARGE
POWER PROPELLED
ROTARY LAWN MOWER
Model No.
917.378431
•Safety
• Assembly
• Operation
• Maintenance
•Espa_ol
•Repalr Parts
CAUTION:
Read and follow all
Safety Rules and Instructions
before operating this equipment
Sears, Roebuck and Co., Hoffman Estates, IL 60179
Visit our Craftsman website: www.sears.corrVcraffsman

Warranty ................................................. 2Product Specifications .......................... 11
Safety Rules ........................................ 2-4 Service and Adjustments................. 13-14
Assembly ............................................. 4-5 Storage ............................................ 15-16
Operation ............................................. 6-9 Troubleshooting .............................. 16-17
Maintenance Schedule ........................ 10 Repair Parts ..................................... 35-43
Maintenance .................................... 10-13 Parts Ordering ........................ Back Cover
LIMITED'I3NO YEAR WARRANTY ON CRAFTSMAN POWER MOWER
For two years from date of purchase, when this Craftsman Lawn Mower is maintained,
lubricated,and tuned up according to the operating and maintenance instructions in
the owner's manual, Sears will repair free of charge any defect in material or workman-
ship.
If this Craftsman Lawn Mower is used for commemial or rental purposes, this warranty
applies foronly 90 days from the date of purchase.
This Warranty does notcover:
• Expendable items which become worn during normal use, such as rotary mower
blades, blade adapters, belts, air cleaners and spark plug.
•Repairs necessary because of operator abuse or negligence, including bent
crankshafts and the failure to maintain the equipment according to the instructions
contained in the owner's manual.
Warranty service is available by returningthe Craftsman power mower to the nearest
Sears Service Centar/Departmant in the United States. This warranty applies only
while this productis in use in the United States.
This Warranty gives you specific legal rights, and you may also have other rightswhich
varyfrom state tostate.
Sears, Roebuck and Co., D/817 WA, Hoftman Estates, Illinois60179
IMPORTANT= This cutting machine is cepabte of amputating hands and feet and
throwingobjects. Failure to observe the following safety instructionscould result in
serious injuryor death.
I. GENERAL OPERATION
•Read, understand, and follow all
instructionson the machine and in the
manual(s) before starting. Be thor-
oughly familiar with the controls and
the proper use of the machine before
starting.
•Do not put hands or feet near or under
rotatingparts. Keep clear of the
discharge opening at atl times.
• Only allow responsibte individuals,
who are familiar with the instructions,to
operate the machine.
•Clear the area of objects such as
rocks,toys, wire, bones, sticks, etc.,
which could be picked up and thrown
by the blade.
•Be sure the area isclear of other
people before mowing. Stop machine if
anyone enters the area.
•Do not operate the mower when
barefoot or weadng open sandals.
Always wear substantial foot wear.
• Do not pull mower backwards unless
absolutely necessary, Always look
down and behind before and while
moving backwards.
•Do not operate the mower without
proper guards, plates, grass catcher or
other safety protective devices in place.
• See manufacturer's instructionsfor
proper operation and installation of
accessories. Only use accessories
approved by the manufacturer.

•Stop the blade(s) when crossing gravel
drives, walks, or roads.
•Stop the engine (motor) whenever you
leave the equipment, before cleaning
the mower or uncloggingthe chute.
•Shut the engine (motor) off and wait
untilthe blade comes to complete stop
before removing grass catcher.
•Mow only in daylight or good artificial
light.
•Do not operate the machine while
under the influence of alcohol or drugs.
•Never operate machine in wet grass.
Always be sure of your footing: keep a
firm hold on the handle and walk; never
run.
•Disengage the self-propeUed mecha-
nism or drive clutch on mowers so
equipped before starting the engine
(motor).
•If the equipment should start tovibrate
abnormally, stop the engine (motor)
and check immediately for the cause.
Vibration is generally a warning of
trouble.
•Always wear safety goggles or safety
glasses with side shields when
operating mower.
IL SLOPE OPERATION
Slopes are a major factor related to slip
and fail accidents which can result in
severe injury.All slopes require extra
caution. If you feel uneasy on a slope, do
notmow it.
DO:
• Mow across the face of slopes: never
up and down. Exercise extreme caution
when changing direction on slopes.
•Remove obstacles such as rocks, tree
limbs, etc.
•Watch for holes, ruts, or bumps. Tall
grass can hide obstacles.
DO NOT=
•Do not trim near drop-offs, ditches or
embankments. The operator could lose
footing or balance.
•Do nottdm excessively steep slopes.
•Do not mow on wet grass. Reduced
footing could cause slipping.
Ill.CHILDREN
Tragic accidents can occur if the operator
isnot alert to the presence of children.
Childrenare often attracted to the
machine and the mowing activity. Never
assume that children will remain where
you last saw them.
• Keep children out of the trimming area
and under the watchful care of another
responsible adult.
•Be alert and turn machine off if children
enter the area.
• Before and while walking backwards,
look behind and down for small
children.
• Never allow children to operate the
machine.
• Use extra care when approaching blind
corners, shrubs, trees, or other objects
that may obscure vision.
IV. SERVICE
•Use extra care in handling gasoline
and other fuels. They are flammable
and vapors are explosive.
- Use only an approved container.
-Never remove gas cap or add fuel
with the engine running.Allow
engine to cool before refueling. Do
not smoke.
-Never refuel the machine indoors.
-Never store the machine or fuel
container inside where there is an
open flame, such as a water heater.
• Never run a machine inside a closed
area.
• Never make adjustments or repairs with
the engine (motor) running. Disconnect
the spark plug wire, and keep the wire
away from the plug to prevent acciden-
tal starting.
• Keep nuts and belts, especially blade
attachment belts, tight and keep
equipment in good condition.
• Never tamper with safety devices.
Check their proper operation regularly.
• Keep machine free of grass, leaves, or
other debris build-up. Clean oil or fuel
spillage. Allow machine to cool before
storing.
• Stop and inspect the equipment if you
strike an object. Repair, if necessary,
before restarting.
• Never attempt to make wheel height
adjustments while the engine (motor) is
running.
•Grass catcher components are subject
to wear, damage, and deterioration,
which could expose moving parts or
allow objects to be thrown. Frequently
check components and replace with
manufacturer's recommended parts,
when necessary.
•Mower blades are sharp and can cut.
Wrap the blade(s) or wear gloves, and
use extra caution when servicing them.
•Do notchange the engine governor
setting or overspeed the engine.

ALook for this symbol to point out
importantsafety precautions. It means
CAUTION!!t BECOMEALERT!t! YOUR
SAFETY ISINVOLVED.
ACAUTION: In orderto prevent
accidental starting when setting up,
transporting, adjusting or making repairs,
always disconnect spark plug wire and
place wire where it cannot contactspark
plug.
&WARNING: Engine exhaust, some of its
constituents, and certain vehicle
components contain or emit chemicals
known to the State of California to cause
cancer and birth defects or other
reproductive harm.
_,WARNING: Battery posts,terminals and
related accessories contain lead and lead
compounds, chemicals known to the State
of California to cause cancer and birth
defects or other reproductive harm. Wash
hands after handling.
_, CAUTION: Muffler and other engine
parts become extremely hotduring
operation and remain hot after engine has
stopped. To avoid severe burns on
contact, stay away fromthese areas.
These accessories were available when this lawn mower was produced. They are not
shipped with your mower. They are also available at most Sears retail outlets and
service centers. Most Sears stores can also order repair partsfor you, when you
provide the model number of your lawn mower. Some of these accessories may not
apply to your lawn mower.
LAWN MOWER PERFORMANCE
CUPPING DEFLECTOR
FOR REAR DISCHARGE LAWN MOWERS MULCHER KITS STABILIZER
GRASS CATCHERS GRASS CATCHERS
FOR FOR
REAR DISCHARGE SIDE DISCHARGE
LAWN MOWERS LAWN MOWERS
GAS CANS
LAWN MOWER MAINTENANCE
MUFFLERS AIR FILTERS SPARK PLUGS
BELTS BLADES BLADE ADAPTERS WHEELS ENGINE OIL
Read these instructions and this manual
in its entirety before you attempt to
assemble or operate your new lawn
mower.
IMPORTANT: This lawn mower is
shippedWITHOUT OIL OR GASOLINE in
the engine.
4

Your new lawn mower has been as-
sembled at the factory with the exception
of those parts left unassembled for
shipping purposes. All parts such as nuts,
washers, bolts, etc., necessary to com-
plete the assembly have been placed in
the parts bag. To ensure safe and proper
operationof your lawn mower, all parts
and hardware you assemble must be
tightened securely. Use the correct tools
as necessary to ensure proper tightness.
TO REMOVE LAWN MOWER FROM
CARTON
1. Remove loose parts included with
mower.
2. Cut down two end corners of carton
and lay end panel down flat.
3. Remove all packing materials except
padding between upper and lower
handle and padding holding operator
presence control bar to upper handle.
4. Roll lawn mower out of carton and
check carton thorougly for additional
loose pads.
HOW TO SET UP YOUR LAWN
MOWER
TO UNFOLD HANDLE
IMPORTANT: Unfold handle carefully so
as not to pinch or damage control cables.
1. Raise handles until lower handle
section locks intoprace in mowing
position.
2. Remove protective padding, raise
upper handle section into place on
lower handle and tighten both handle
knobs.
3. Remove handle padding holding
operator presence control bar to
upper handle.
Your lawn mower handle can be adjusted
for your mowing comfort. Refer to "AD-
JUST HANDLE" in the Service and
Adjustmentssection of this manual.
Operator
con_'olbar
Liftu
Mowing
position
TO INSTALL A'I'I'ACHM ENTS
Your lawn mower was shipped ready to
be used as a mulcher. To convert mower
to bagging, see "TO CONVERT MOWER"
in the Operation section of this manual.
TO PREPARE BA'I'rERY
NOTE: Your battery must be charged
before you can start your lawn mower.
1. Disconnect engine battery connector
(male) from battery connector (female)
2. Connect battery charger connector
(male) to battery connector (female).
3. Plug battery charger into110 volt A.C.
outlet.
4. Leave battery charger connected for
24 hours before starling your engine
forthe first time.
5. After charging, connect engine
connector (male) to battery connector
(female).
Your engine has an integral alternator for
partial charging. Connect your battery
charger to charge battery as required.
IMPORTANT: The engine alternator will
not charge a discharged battery.
At the end of the mowing season the
battery should be charged for 48 hours to
protect the battery duringwinter storage.
ACAUTION: Always disconnect the
engine connector (male) from the battery
connector (female) to prevent accidental
starting when transperting or storing your
lawn mower after the season.
Charger connector Battery connector
Engine connector (male) Battery charger
Lowerhandle5

KNOWYOURLAWNMOWER
READ THIS OWNER'S MANUALAND SAFETY RULES BEFORE OPERATING YOUR
LAWN MOWER. Compare the illustrationswith your lawn mower to familiarize yourself
with the locationof various controls and adjustments. Save this manual for future
reference.
These symbols may appear on your lawn mower or In literature supplied with the
product, Learn and understand their meaning.
CAUTION ENGINE ENGINE FAST SLOW CHOKE FUEL OIL DANGER, KEEP HANDS
OR WARNING ON OFF AND FEET AWAY
Engine zone
control
Auxlfiary
starter handle
presence control her
start switch
Engine oil cap
with
Gasoline cap
Air filter
Primer
Muffler
Ddve cover
Housin
IMPORTANT: This lawn mower is shipped _Wheel adjuster
WITHOUT OIL OR GASOLINE in the engine (on eachwheel)
MEETS CPSC SAFETY REQUIREMENTS
Sears rotarywalk-behind power lawn mowers conformto the safety standards of the
American National Standards Instituteand the U.S. Consumer Product Safety Commis-
sion. The blade turns when the engine is running.
Operator presence control bar - must
be held down to the handle to start the
engine. Release to stop the engine,
Key start switch- used for starting the
engine,
Auxiliary starter handle -used for
starting the engine.
Primer -pumps additional fuel from the
carburetor to the cylinderfor use when
starting a cold engine.
Drive control lever - used to engage
power-propelled forward motion of lawn
mower,
6

Theoperationofany lawn
mower can result in foreign
objects thrown into the
eyes, which can result in
severe eye damage.
Always wear safety glasses or eye
shields while operating your lawn mower
or performing any adjustments or repairs.
We recommend a wide vision safety
mask over spectacles or standard safety
glasses.
HOW TO USEYOUR LAWN MOWER
ENGINE SPEED
The engine speed was set at the factory
for optimumperformance. Speed is not
adjustable.
ENGINE ZONE CONTROL
ACAUTION: Federal regulations require
an engine controlto be installed on this
lawn mower in order to minimize the risk
of blade contact injury.Do notunder any
circumstances attempt todefeat the
function of the operator control. The blade
turns when the engine is running.
•Your lawn mower is equipped with an
operator presence control bar which
requires the operator to be positioned
behind the lawn mower handle to start
and operate the lawn mower.
DRIVE CONTROL
•Self-propelling is controlled by holding
the operator presence control bar down
to the handle and pushing the drive
control Teverforward until it clicks;then
releasing the lever.
•Forward motionwill stop when the
operator presence control bar is
released. To stop forward motion
without stopping engine, release the
operator presence control bar slightly
until the drive control disengages. Hold
operator presence control bar down
against handle to continue mowing
without self-propelling.
•To keep drive control engaged when
turningcomers, push down on handle
and liftfront wheels off ground while
turning lawn mower. Drive
control
TO ADJUST CU'I-rlNG HEIGHT
Raise wheels for low cut and lower
wheels for high cut, adjust cuttingheight
to suit your requirements. Medium
positionis best for most lawns.
•TO change cutting height, squeeze
adjuster lever toward wheel. Move
wheel up or down to suit your require-
ments. Be sure all wheels are in the
same setting.
NOTE: Adjuster is properly positioned
when plate tab inserts into hole in lever.
Also. 9-pesition adjusters (if so equipped)
allow lever to be positioned between the
plate tabs.
LowerWheelsfor High Cut Plat_Ta_l,
RaiseWheels forLowCut Lever
TO CONVERT MOWER
Yourlawnmowerwas shippedreadytobe
usedas a mulcher.Toconverttobegging :
REAR BAGGING
• Uft mar door ofthe lawn mower and place
the grass catcherframe hooksonto the
doar pivct p_ns.
•To convert tomulching ope_, remove
grasscatcher and dose reardoor.
ACAUTION: Do not runyour lawn mower
without clipping deflector or approved
grass catcher in place, Never attempt to
operate the lawn mower with the rear
door removed or propped open.
Pivot " Rear Grass
catcher
handle
Catcher frame hook
To engage Ddve control
drive control disengaged 7

TO EMPTY GRASS CATCHER
1. Open door and lift up on grass catcher
using the frame handle.
2. Remove grass catcher with clippings
from under tawn mower handle.
3. Empty clippingsfrom bag using both
frame handle and bag handle.
NOTE: Do not drag the bag when
emptying; itwill cause unnecessary wear.
Grass
catcher
handle
Bag
handle
BEFORE STARTING ENGINE
ADD OIL
Your lawnmower is shipped without oil in
the engine. Engine holds 20 oz. of oil.
For type and grade ofoil to use, see
"ENGINE" in Maintenance section of this
manual.
1. Be sure lawnmower is level and area
around oil fill is clean.
2. Remove engine oft cap and fill to the
full line on the dipstick. Pour oil slowly.
Do not over fill.
NOTE: Allow oil to settle down intoengine
foraccurate reading. To read proper level,
tighten engine oil cap, then remove it to
read the dipstick.
3. Reinstall engine oil cap and tighten.
• Check oil level before each use. Add
oil if needed. Fillto full lineon dipstick.
•Change the oil after every 25 hours of
operation or each season. You may
need to change the oil more often
under dusty, dirty conditions.
ADD GASOLINE
•Fillfuel tank. Use fresh, clean, regular
unleaded gasoline with a minimum of
87 octane. Do not mix oil with gaso-
line. Purchase fuel in quantities that
can be used within 30 days to assure
fuel freshness.
AWARNING: Experience indicatesthat
alcohol blended fuels (called gasohol or
using ethanol or methanol) can attract
moisture which leads to separation and
formationof acids during storage. Acidic
gas can damage the fuel system of an
engine while in storage. To avoid engine
problems, the fuel system should be
emptied before storage of 30 days or
longer. Drain the gas tank, start the
engine and let it run untilthe fuel lines
and carburetor are empty. Use fresh fuel
next season. See Storage Instructionsfor
additional information. Never use engine
or carburetor cleaner products in the fuel
tank or permanent damage may occur.
A CAUTION: Filltobottom ofgas tank
filler neck. Do not ovedill. Wipe off any
spilled oil or fuel. Do not store, spill or
use gasoline near an open flame.
filler cap
Engine
oil cap
TO START ENGINE
NOTE: Due to protective coatings onthe
engine, a small amount ofsmoke may be
present during the initial use of the
product and should be considered
normal.
I. TO start a cold engine, push primer
three (3) times before tryingto stad.
Use afirm push, This step is not
usually necessary when starting an
engine which has already run for a
few minutes.
2. Hold operator presence control bar
down to the handle.
3. Turn electric start key clockwiseto
crank engine.

IMPORTANT:Do notcrank engine more
than five continous seconds between
each time you try to start. Wait 5 to 10
seconds between each attempt.
1. To start engine using the auxiliary
starter handle, follow the steps above.
Exchange the use of the start key for
starter handle. Pull starter handle
quickly. Do not allow starter rope to
snap back.
TO STOP ENGINE
To stop engine, release operator
presence control bar.
NOTE: In cooler weather it may be
necessary to repeat priming steps. In
warmer weather over priming may cause
flooding and engine will notstart. If you
do flood engine wait a few minutes before
attemptingto start and do not repeat
priming steps.
MOWING TIPS
•Under certain conditions, such as very
tall grass, it may be necessary to raise
the height of cut to reduce pushing
effort and to keep from overloading the
engine and leaving clumps of grass
clippings. It may also be necessary to
reduce ground speed and/or run the
lawn mower over the area a second
time.
•For extremely heavy cuffing, reduce the
width of cut by overlapping previously
cut path and mow slowly.
•For better grass bagging and most
cuttingconditions, the engine speed
should be set in the fast position.
•When using a rear discharge lawn
mower in moist, heavy grass, clumps of
cut gross may notenter the grass
catcher. Reduce ground speed
(pushing speed) and/or run the lawn
mower over the area a second time.
•If a trailof clippingsis left on the right
side of a rear discharge mower, mow in
a clockwise directionwith asmall
overlap to collect the clippings on the
next pass.
•Pores in cloth grass catchers can
become filled with dirt and dust with
use and catchers will collect less grass.
To prevent this, regularly hose catcher
off with water and let dry before using.
•Keep top of engine around starter clear
and clean of grass clippings and chaff.
This will help engine air flow and
extend engine life.
MULCHING MOWING TIPS
IMPORTANT: Forbestperformance,
keep mower housing free of built-up
grass and trash. See "CLEANING" in the
Maintenance section of this manual.
•The special mulching blade will recut
the grass clippings many times and
reduce them in size so that as they fall
onto the lawn they will disperse into the
grass and notbe noticed. Also,the
mulched grass will biodegrade quickly
to provide nutdents for the lawn.
Always mulch with your highest engine
(blade) speed as this will provide the
best recutting action of the blades.
• Avoid cutting your lawn when it is wet.
Wet grass tends to form clumps and
interferes with the mulching action.
The best time to mow your lawn is the
early afternoon. At this time the grass
has dried and the newly cut area will
not be exposed to the direct sun.
• For best results, adjust the lawn mower
cutting height so that the lawn mower
cuts off only the top one-third of the
grass blades. If the lawn is overgrown
it will be necessary to raise the height
of cut to reduce pushing effort and to
keep from overloading the engine and
leaving clumps of mulched grass. For
extremely heavy mulching, reduce your
width of cut by overlapping previously
cut path and mow slowly.
• Certain types of grass and grass
conditions may require that an area be
mulched a second time to completely
hide the clippings. When doing a
second cut, mow across or perpendicu-
larto the first cut path.
•Change your cuttingpattern from week
to week. Mow north to south one week
then change to east towest the next
week. This will help prevent matting
and graining of the lawn.
Max 1/3
9

.A,NTENANCEBC.EDU'E
Check forLoose Fasteners _I_
Clean/Inspect Grass Catcher
(if Equipped) I_ I/
MClean Lawn Mower I_ I/Clean Under Drive Cover
WIPower-PrOpelled Mowers) t_SCheck drive bel ulleys
(Powe r-Propell_lPMowers) V
R check/Sharp•n/ReplaceBlade r_'_
LubriCationChart ¥/ i/
Clean BatteP//ReChar_
Electric Start Mowers li/ 1/4
ECheck Engine Oil Level t/
N Change Engine Oil t/l_t
Clean Air Filter I_ 2
Inspect Muffler
Clean or Replace Spark Plug f_
E Replace Air Filtar Paper Cadridge ItS=
t - Change monaoftenwhen opgralklgunde_• heavy loador inhigh ambkml I_111_alum$.
2-Sarvk:emorl o_len_operetlng Indirty or dusty conditions.
3 - Re_,uce bladesmo,e often whim mowing insandy =o_,
4- Cha_e 48 hour_ atend of =e_
GENERAL RECOMMENDATIONS
The warranty on this lawn mower does
notcover items that have been subjected
to operator abuse or negligence. To
receive full value from the warranty,
operator must maintain mower as
instructedin this manual.
Some adjustments will need to be made
periodicallyto properly maintain your
unit.
All adjustments in the Service and
Adjustments section ofthis manual
should be checked at least once each
season.
•Once a year, replace the spark plug,
clean or replace air filter element and
check blade for wear. A new spark
plug and clean/new air filter element
assures proper air-fuel mixture and
helps your engine run better and last
longer.
•Follow the maintenance schedule in
this manual.
LUBRICATION CHART
(_) Wheeladjuster
eachwheel)
(_) Brake
spring
bracket
Rear
(_) Handle bracket mounting pins door hinge
(_) Spray lubricant
(_) See "ENGINE" In Maintenance section.
BEFORE EACH USE
1. Check engine oil level.
2. Check for loose fasteners.
LUBRICATION
Keep unit well lubricated (See "LUBRI-
CATION CHART'). 10
IMPORTANT: Do notoil or grease
plastic wheel bearings. Viscous
tubricantswillattract dust and did that
will shorten the life of the self-lubricat-
ing bearings. Ifyou feel they must be
lubricated, use onlyadry, powdered
graphite type lubricantsparingly.

PRODUCT SPECIFICATIONS
ERIAL NUMBER:
DATE OF PURCHASE:
GASOLINECAPACITY/TYPE: 1.5 QUARTS (UNLEADED REGULAR)
OIL'tYPE (API-SF-SJ): SAE 30 (ABOVE 32°F); SAE 5W-30 (BELOW 32°F
OIL CAPACITY: 20 OUNCES
SPARK PLUG (GAP: .045") CHAMPION RESISTOR TYPE RJ19LM4
BLADE BOLTTORQUE: 35-40 FT. LBS.
The model and serial numbers will be found on adecal on the rear of the mower
housing. Record both serial number and date of purchase in space provided above
LAWN MOWER
Alwaysobservesafetyruleswhen perform-
ingany maintenance.
TIRES
• Keeptiresfreeofgasoline,oil,or insect
contrelchernicalswhichcan harm rubber.
•Awid stumps,stones,deed ruts,shaq3
objectsand otherhazardsthat maycause
_m damage.
BLADE CARE
For best results, mower blade must be
kept sharp. Replace bent or damaged
blades.
TO REMOVE BLADE
1. Disconnect spark plug wire from spark
plug and place wire where it cannot
come in contact with spark plug.
2. Turn lawn mower on its side. Make
sure air filter end carburetor are up.
3. Use a wood block between blade and
mower housingto prevent blade from
turning when removing blade bolt.
NOTE; Protect your hands with gloves
and/or wrap blade with heavy cloth.
4. Remove blade bolt by turning counter-
clockwise.
5. Remove blade and attaching hard-
ware (bolt, lock washer and hardened
washer).
NOTE: Remove the blade adapter and
check the key inside hub of blade
adapter. The key must be in good condi-
tionto work properly.Replace adapter if
damaged.
TO REPLACE BLADE
1. Position the blade adapter on the
engine crankshaft. Be sure key in
adapter and crankshaft keyway are
aligned.
2. Positionblade on the blade adapter
aligningthe two (2) holes in the blade
with the raised lugs on the adapter.
3. Be sure the trailingedge of blade
(opposite sharp edge) is up toward
the engine.
4. Install the blade bolt with the lock
washer and hardened washer into
blade adapter and crankshaft.
5. Use block of wood between blade and
lawn mower housing and tighten the
blade bolt, turning clockwise.
• The recommended tightening torque is
35-40 ft. Ibe.
IMPORTANT: Blade bolt isgrade 8 heat
treated.
TO SHARPEN BLADE
NOTE: We do not recommend sharpen-
ing blade - but if you do, be sure the
blade is balanced.
Care should be taken to keep the blade
balanced. An unbalanced blade will
cause eventual damage to lawn mower
or engine.
•The blade can be sharpened with afile
or on a grinding wheel. Do not attempt
to sharpen while on the mower.
• To check blade balance, drive anail
intoabeam or wall. Leave about one
inch ofthe straight nail exposed. Place
center hole of blade over the head of
the nail. If blade is balanced, it should
remain in a horizontal position. If either
end of the blade moves downward,
sharpen the heavy end untilthe blade
is balanced.
Crankshaft
Key_. _keyway
Blade
Blade shaft
b_t
11 washer Trailing edge Blade adapter

GRASS CATCHER
•The grass catcher may be hosed with
water, but must be dry when used.
•Check your grass catcher often for
damage or deterioration. Through
normaluse itwill wear. If catcher
needs replacing, replace only with a
manufacturer approved replacement
catcher. Give the lawn mower model
number when ordering.
DRIVE WHEELS
Check front drive wheels each time
before you mow to be sure they move
freely.
The wheels not turningfreely means
trash, grass cuttings, etc. are in the drive
wheel area and must be cleaned to free
drive wheels.
If necessary to clean the ddve wheels,
check both front wheels.
1. Remove hubcaps, hairpin cotters and
washers.
2. Remove wheels from wheel adjusters.
3. Remove any trash or grass cuttings
from inside the dust cover, pinion and/
or drive wheel gear teeth.
4. Put wheels back in place.
NOTE: If after cleaning, the drive wheels
do not turn freely,contact a Sears or other
qualified service center.
GEAR CASE
•To keep your drive system working
properly, the gear case and area
around the drive should be kept clean
and free oftrash build-up. Clean under
the drive cover twice a season.
• The gear case isfilled with lubricant to
the proper level at the factory. The only
time the lubricant needs attention is if
service has been performed on the
gear case.
•If lubricantis required, use only Texaco
Starplex Premium 1 Grease, Part No.
750369. Do not substitute.
ENGINE
LUBRICATION
Use only high quality detergent oil rated
withAPI service classificationSF-SJ.
Select the oil'sSAE viscosity grade
according to your expected operating
temperature.
NOTE: Although multi-viscosityoils
(5W30, 10W30 etc.) improve starting in
cold weather, these multi-viscosity oils
wilt result in increased oil consumption
when used above 32°F. Check your
engine oi( level more frequently to avoid
possible engine damage from running
low on oil.
Change the oil after every 25 hours of
operation or st least once a year if the
lawn mower is not used for 25 hours in
one year.
Check the crankcase oil level before
starting the engine and after each five (5)
hours of continuous use. -tighten oil plug
securely each time you check the oil
level.
TO CHANGE ENGINE OIL
NOTE: Before tippinglawn mower to
drain oil, drain fuel tank by running
engine until fuel tank is empty.
1. Disconnect spark plugwire from spark
plug and place wire where it cannot
come in contact with spark plug.
2. Remove engine oil cap; lay aside on a
clean surface.
3. Tip lawn mower on its side as shown
and drain oil into a suitable container.
Rock fawn mower back and forthto
remove any oil trapped inside of
engine.
4. Wipe off any spilled oil on lawn mower
and on side of engine.
5. Fill engine with oil. (See "ADD OIL" in
the Operation section ofthis manual.)
6. Reconnect spark plug wire to spark
plug.
AIR FILTER
Your engine will not run propedy and may
be damaged by usinga dirty air filter.
Replace the air filter every year or after
every 100 hoursof operation, more often
if you mow in very dusty, dirty conditions.
Do notwash air filter.
12

TO CHANGE AIR FILTER
1. Remove the air filter by turning
clockwise to the stop and pull away
from collar.
2. Remove filter from inside of cover.
3. Clean the inside of the cover and the
collar to remove any dirt aocumule-
tien.
4. Insert new filter into cover.
5. Put air filter cover and filter intocollar
aligningthe tab with the slot.
6. Push in on cover and turn counter-
clockwise to tighten.
Collar
Slot
Clip
Turn
clockwise
to
Airfilter Turn
counter-
Airfiltercover dock-wiseto tighten
MUFFLER
Inspect and replace corroded muffler as it
could create a fire hazard and/or dam-
age.
SPARK PLUG
Replace spark plugs at the beginning of
each mowing season or after every 100
hours of operation, whichever occurs first.
Spark plug type and gap setting are
shown in "PRODUCT SPECIFICATIONS"
in Maintenance section of this manual.
CLEANING
IMPORTANT: For best performance,
keep mower housing free of built-up
grass and trash. Clean the underside of
your mower after each use.
_;kCAUTION: Disconnect spark plug wire
from spark plug and place wire where it
cannot come in contact with the spark
plug.
•Clean the underside of your lawn
mower by scraping to remove build-up
of grass and trash,
•Clean engine often to keep trash from
accumulating. A clogged engine runs
hotter and shortens engine life.
• Keep finished surfaces and wheels free
of all gasoline, oil,etc.
•We do not recommend using a garden
hose to clean lawn mower unless the
electrical system, muffler, air filter and
carburetor are covered to keep water
out. Water in engine can result in
shortened engine life.
CLEAN UNDER DRIVE COVER
Clean under drive cover at least twice a
season. Scrape underside ofcover with
putty knifeor similartool to remove any
build-up of trash or grass on underside of
drive cover.
_CAUTION: Before performing any
service or adjustments:
1. Release control bar and stop engine.
2. Make sure the blade and all moving
parts have completely stopped.
3. Disconnect spark plug wire from spark
plug end place where it cannot come
in contactwith plug.
LAWN MOWER
TO ADJUST CUTTING HEIGHT
See "TO ADJUST CUTTING HEIGHT" in
the Operation section of this manual.
REAR DEFLECTOR
The rear deflector, attached between the
rear wheels of your mower, is provided to
minimize the possibilitythat objects will
be thrown out of the rear of the mower
into the operator mowing position. Ifthe
deftsctor becomes damaged, it should be
replaced.
13

TOREMOVE/REPLACEDRIVEBELT
1. Removedrivecover.Removebelt
from geamese pulley by pushing
down on pulley and rollingbelt off it.
2. Turn lawn mower on its side with air
filter and carburetor up.
3. Remove blade.
4. Remove debris shield.
5. Remove belt from engine pulley on
crankshaft.
6. Install new belt by reveming above
steps.
7. Always use factory approved belt to
assure fit and long life.
Drive
cover Belt
TO ADJUST HANDLE
The upper handle may be adjusted to
four (4) different height positions.
1. Loosen both handle knobs only
enough to allow the upper handle to
pivot to the desired adjustment
position.
2. Tighten both handle knobs securely.
Handle knob
TO ASSEMBLE GRASS CATCHER
1.Put grass catcher frame into grass bag
with rigid part of bag on the bottom.
Make sure the frame handle is outside
of the bag top.
2. Slip vinyl bindings over frame.
NOTE: Ifvinyl bindingsare too stiff,hold
them inwarm water for a few minutes. If
bag gets wet, let it dry before using.
ACAUTION: Do not runyour lawn
mower without clippingdallector or
approved grass catcher in place. Never
attempt to operate the lawn mower with
the rear door removed or propped open.
Ca_
frame
handle
opening
ENGINE
ENGINE SPEED
Your engine speed has been factory set.
Do not attempt to increase engine speed
or it may resultin personal injury.If you
believe that the engine is runningtoo fast
or too slow,take your lawn mower to a
Sears or other qualified service center for
repair and adjustment.
CARBURETOR
Your carburetor has a non-adjustable
fixed main jet for mixturecontrol. Ifyour
engine does not operate propedy due to
suspected carburetor problems, take
your lawn mower to a Sears or other
qualified service center for repair and/or
adjustment.
IMPORTANT: Never tamper with the
engine governor, which is factoryset for
proper engine speed. Overspeeding the
engine above the factory high speed
setting can be dangerous. Ifyou think the
engine-governed high speed needs
adjusting,contact a Sears or other
qualified service center, which has
proper equipment and experience to
make any necessary adjustments.
14

Immediately pmpara your lawn mower for
storage at the end of the season or if the
unitwill not be used for30 days or more.
LAWN MOWER
When lawn mower is tobe stored for a
periodof time, clean it thoroughly, remove
all did, grease, leaves, etc. Store in a
clean, dry area.
1. Clean entire lawn mower (See
"CLEANING" in the Maintenance
section of this manual).
2. Lubricate as shown in the Mainte-
nance section of this manual.
3. Be sure that all nuts, bolts, screws,
and pins are securely fastened.
Inspect moving parts for damage,
breakage and wear. Replace if
necessary.
4. Touch up all rustedor chipped paint
surfaces; sand lightlybefore painting.
HANDLE
You can fold your lawn mower handle for
storage.
1. Squeeze the bottom ends of the lower
handle toward each other untilthe
lower handle clears the handle
bracket, then move handle fonvard.
2. Loosen upper handle mounting bolts
enough to allow upper handle to be
folded back.
IMPORTANT: When foldingthe handle
for storage or transportation, be sure to
fold the handle as shown or you may
damage the controlcables.
• When setting up your handle from the
storage position, the lower handle will
automatically lock into the mowing
position.
Squeeze to fold Handle
Mounting pin
Operator
control bar Fold
Lower
Fold
backward
Mowing
position
Hairpin cotter
ENGINE
FUEL SYSTEM
IMPORTANT: Itis importantto prevent
gum deposits from forming in essential
fuel system parts such as carburetor, fuel
filter, fuel hose, or tank duringstorage.
Also, experience indicates that alcohol
blended fuels (called gasohol or using
ethanol or methanol) can attract moisture
which leads to separation and formation
of acids during storage. Acidic gas can
damage the fuel system of an engine
while in storage.
1. Drain the fuel tank.
2. Start the engine and let it run untilthe
fuel lines and carburetor are empty.
• Never use engine or carburetor cleaner
products in the fuel tank or permanent
damage may occur.
•Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable
alternative in minimizing the formation of
fuel gum deposits during storage. Add
stabilizer to gasoline in fuel tank or
storage container. Always follow the mix
ratio found on stabilizer container. Run
engine at least 10 minutes after adding
stabilizer to allow the stabilizer to reach
the carburetor. Do not drain the gas tank
and carburetor if using fuel stabilizer.
ENGINEOIL
Drain oil (with engine warm) and replace
with clean engine oil. (See "ENGINE =in
the Maintenance section of this manual).
CYLINDER
1. Remove spark plug.
2. Pour one ounce (29 ml) of oil through
spark plug hole intocylinder.
3. Pull starter handle slowly a few times
to distributeoil.
4. Replace with new spark plug.
15

BA'I'rERY
Disconnectthebatteryfromtheengine
connectorandchargebattery48hours.
OTHER
•Do not store gasoline from one season
to another.
•Replace your gasoline can if your can
startsto rust. Rust and/or dirt inyour
gasoline will cause problems.
•If possible, store your unit indoors and
cover it to protectit from dust and dirt.
•Cover your unit with a suitable protec-
tive cover that does not retain moisture.
Do not use plastic. Plastic cannot
breathe, which allows condensation to
form and willcause your unitto rust.
IMPORTANT: Never cover mower while
engone and exhaust areas are still warm.
ACAUTION:Never store the lawn mower
with gasoline in the tank inside a building
where fumes may reach an open flame or
spark. Allow the engine to cool before
storing in any enctosure.
TROUBLESHOOTING CHART
PROBLEM CAUSE
goes not start 1. Dirty air filter.
2. Out of fuel.
3. Stale fuel.
4. Water in fuel.
5. Spark plug wire is
disconnected.
6. Bad spark plug.
7. Loose blade or broken
blade adapter.
8. Control bar in released
position.
9. Control bar defective.
10.Weak Battery
11.Disconnected battery
connector.
CORRECTION
1. Clean/replace air filter.
2. Fillfuel tank.
3. Drain tank and refillwith
fresh, clean fuel.
4. Drain fuel tank and
carburetor and refilltank
with fresh gasoline.
5. Connect wire to plug.
6. Replace spark plug.
7. Tighten blade boltor
replace blade adapter.
8. Depress control bar to
handle.
9. Replace control bar.
1O.Charge battery.
11.Connect battery to engine.
16

TROUBLESHOOTINGCHART
CAUSE
1. Rear _lawn mower
PROBLEM
Loasofpower
Poorcut-
Jneven
housing or cutting blade
dragging in heavy grass.
2. Cutting too much grass.
3. Dirty air filter.
4. Buildupof grass, leaves,
and trash under mower.
5. Too much oil in engine.
6. Walking speed too fast.
1. Worn, bent or loose blade.
2. Wheel heights uneven.
3. Buildupof grass, leaves
and trash under mower.
1. Worn, bent or loose blade,
2. Bent engine crankshaft.
CORRECTION
1. Set to "Higher Cut"
position.
2. Set to "Higher Cut"
position.
3. Cleardreptace air filter.
4. Clean underside of mower
housing.
5. Check oil level.
6. Cut at slower walking
speed.
1. Replace blade. Tighten
blade bolt.
2. Set all wheels at same
height.
3. Clean underside of
mower housing.
Excessive 1. Replace blade. Tighten
vibration blade bolt.
2. Contact aSears or other
qualified service center.
Starter rope 1. Engine flywheel brake is on
hard to pull when control bar is release¢
2, Bent engine crankshaft.
3. Blade adapter broken.
4. Blade dragging in grass.
1. Depress controlbar to
upper handle before
pulling starter rope.
2. Contact a Sears or other
qualified service center.
3. Replace blade adapter.
4. Move lawn mower to cut
grass or to hard surface.
Loss of drive 1. Drive wheels not turning 1. Adjust or replace drive
with drive control engaged, control cable.
2. Belt not driving 2. Put belt on pulleys or
replace belts if broken.
Grass catcher 1, Cutting height too low. 1. Raise cutting height,
notfllllng (if so 2. Lifton blade worn off. 2. Replace blade.
equipped) 3. Catcher not venting air. 3. Clean grass catcher.
Hard to push 1, Raise cutting height.1. Grass is too high or wheel
height istoo low.
2, Rear of lawn mower
housing or cutting blade
dragging in grass.
3. Grass catcher too full.
4. Handle height position not
rightfor you.
2. Raise rear of lawn mower
housing one (1) setting
higher.
3. Empty grass catcher.
4. Adjust handle height to
suit.
17

Garant[a ................................................ 18
Reglas de Seguridad ...................... 18-20
Montaje ............................................ 20-21
Operaci_n ........................................ 22-25
Mantenimiento ................................. 26-29
Programa de Mantenimiento................ 26
Especificaclones del Producto ............. 27
Servicio y Adjustes .......................... 30-31
Almacenamiento ............................. 31-32
Identificaci6n de problemas ............ 33-34
Panes de repuesto ............ Vea el manual
ingl4Jsde_due_o
GARANTfA L|MITADA DE DOS _OS PAPA LA SEGADORA A MOTOR CRAFTSMAN
Pot dos (2) at3os a pertir de la fanha de cornpra cuando esta Segadora Craftsman se
mantanga, lubdque y afine segt3ntas instruccionsa para la operacibn y el mantenimiento an el
manual del due_o Sears reparard gratis todo defecto an el matadal y la mano de obra
Si la Sagadota Craftsman se usa pare fines comemiales o de erriando, esta garantia s61ose
aplica per noventa (90) dlas a partir de la fecha de compra
Esta Garant[a no cubra:
•Artloulos qua sa desgastan durante el use normal tares como las cuchiflsa segadoras
rotatoti=s, los adaptadores de la cuchtila, 1ascorreas los ftitros de airs y las bujlaa
•Reperaciones necesadas debido al abuso o ala negligencia del operadot incluy6ndosa a los
cig',e_ales doblados y ala falta de mantenimiento del equipo segOn las instrucciones qua sa
incluyan en el manual del due5o
EL SERVIClO DE GARANTfA ESTA DISPONIBLE al devolver la sagadora a motor Craftsman al
CentroiDapartmento de Servicio Sears mas cercano an los Estados Unidos Esta garanda sa
aplica solamenta mlantras el producto esta an usa en los Estados Unidos
Esta Garande _eotorga derechos tegalsa especffloos y puede qua tambf_n tenga otros
derechos que vadan de estado aestade
Sears, Roebuck and Co,, D/817 WA, Hoffman Estates, Illinois 60179 USA
IMPORTANTE: Esta maquina cortadaora es capaz de amputar las manos y los manos y los
pies y de lanzar objetos Si no sa observan las instrucciones de sagundad siguiantes se pueden
producir laslones graves o la muerLe
I OPERACION
•Antes de empezar, debe familiarizarse
completamante con los controtes y el usa
correcto de la maquina Pars esto, debe leer
y comprender todas tas instrucciones qua
aparecen en la maquina yan los manuales
de operaci6n
•Nopongalasmanosotospiescereao
debajo de las partes rotatorias Mant6ngasa
siempre lejos de la abertura de la descarga
•Permita que solarnente lea personas
responsables qua est6n familiarizadas con
las instruccioues operan la mdquina
•Despeje el &rea de objetos tales coma
piedras juguetas, alambres, huesos palos
etc que pueden eer recogidos y lanzados
pot )as cuchJJ]as
•Asag0resa qua el drea no se hallen
personas antes de sagar Pare la maquina
sialguian entre en el drea
•NO opera la maquina sin zapatos o con
sandellas abiertas Pbngase siempre
zapatos s_idos
•NO tirede la segadora hacia atrds a manos
qua sea absolutarnenta necosado. Mire
siemprs hania abajo y hacia detrds antes y
miantrsa que se mueve hacia atrds
•No opere la sagadora sin los rsspectivos
resguardos, las places el recogndor de
c6sped u otres aditamentos dise ados para
su pmteocibn y seguddad
•Refi6rasa alas instrucclones del fabricante
pare el funcionamiento e instalaci6n de
accsaodos Use ,,nicamente acuesorios
aprobados per el fabncante
•Detanga la cuchilla o las cuchiUascuando
cruce pot calzadas, calles o caminos de
grave
•Parer el motor cada vez qua so abandona
el aparato, antes de 5mpiarla segadora o de
remover residuos del tubo
•Apagar el motory esperar haste que las
cuchillas est6n complatamente parades
antes de remover el receptor de hierba
•Sager solamante con luz del die o con una
buena luz artificial.
NO opera la mdquina bajo la influenciadel
alcohol o de las dregas,
18

• Nunca opera la maquina ouando la hierba
est6 mojada Aseg0rese siempre de taner
buena tracoibn en sus pies; mantenga el
mango firmaments y carnine; nunca corra
•Desconectar el mecanismo de propulsi6n
autbnoma o el embrague de transmisi6n en
las segadOras qua Io tienan antes de poner
en marcha el motor
• Si el equipo empezara a vibrar de una
manara anormal, pare el motor y revise de
inmediato pars averiguar la causa
Generelmenta la vibraci6n susie indicar que
exista atguna averfa
•Siampre use galas de seguddad o antecjos
con protecok_nlateral cuando opere la
segadora
IL OPERAClON SOBRE I.AS CUESTAS
Los acoidentes ocurren con mds frecuencia
an les cuestas Es_s aesidentes ocurren
debido a resbeladas o cafdas, las cuales
pueden resultar en graves lesiones Operar la
recortadora en cuestas requiem mayor
concentraelbn Si se siente inseguro an ona
cuesta, no la recorte
HACER:
•Posde recortar a trav6s de la superficie de
la cossta, nunca hacia arriba y hacia abajo
Proosda con extrema precaucibn cuando
nambie de direc_Y_ en lascuestas
•Renueva todos los objetos extraSos, tales
como guijarros, ramas, etc
•Debe prestar atenci6n a hoyos, baches o
protuberanelas Recuerde que la hierba alta
puede esconder obstdculos
NO HACER:
•No recorte osrca de pendientes, zanjas o
terraplenes El operador puede perder la
tracci6n en los pies o el equilibrio
•No recorte cuestes demasiado inclinadas
• No recorte en hierba majada La reducoidn
en la traccic_nde la pisada puede causar
resbalones.
III. NINOS
Se pueden producir accidentes trdgicos si el
operador no presta atanci6n a la presencia de
los nihos A menudo, tos ni_os se sientan
atraidos por la mbquina y por la actividad de la
siega Nunos suponga qua los niSos van a
perrnaneosr en el mismo lugar donde los vio
por ,'.ltimavez
• Mantenga a los nii',osalejados del drea de la
siega y bajo el cuidado estdcto de otrs
persona adulta responsable
•Est6 alerts y apague la mdquina si hay ni_os
qua entran al drea
• Antes y cuando este retrocediendo, mire
hacia atrds y hacia abajo para verificar si
hay elt_os pequerlos
•Nonca permita que los nifios operen la
mdquina
•Tenga un cuidado extra cuando se acerque
a esquinas donde no hay visibilidad, a los
arbustos, t=rboles u otros objetos que
pueden interfedr con su lines de visibn
IV. SERVIClO
•Tenga cuidado extra al manejar la gasolina
y los dernds combustibles Son inflamables
y los gases son explosivos
Use solarnente un envase aprobado
Nunca remueva la tapa del dep6sito de
gasolina o agregue combustible con el
motor funcionando Permita qua el motor
se enfrfe antes de vo_ver a pone
combustible No fume
Nunna vuelva aponer combustible en la
mdquina en recintos cerrados
Nunca almaosne la mdquina o el envase
del combustible dentro de alg0n lugar en
doncle hays una llama expuesta, tel cot'no
la del celentador de agua
•Nunca haga funcionar una m6quina dentro
de un drea cerrada
•Nunca hags ajustes o reparaciones
rnientras el motor est6 en mamha
Desconecte el cable de la bujla, y
mantdngalo acierta distancia de 6sta para
prevenir un arranque accidental.
• Mantenga las tuercas y los pemos,
especialmenta los pemos del accesorio de
la ouchilla, apretados y mantenga el equipo
en buenas condiciones
•Nunca manipule de forma indebida los
disposiUvos de seguridad Controls
regularmente su funcionamiento correcto
•Mantanga la mdquina librade hierba, hojas
u otras acumuleciones de desperdicio
Limpie los derrames de acelte o combus-
tible Permita que la mdquina se enfrfe antes
de almaosnarla
•Pare e inspeccione el equipo si le pega aun
objeto Repdrelo, si es nacesado, antes de
hacedo arranosr
•En ning0n caso hay qua regular la altura de
les tuedas mientras el motor est_ en
marcha
•Los componentes del receptor de la hierba
van sujetos a desgasta, dafios y deterioro
que pueden exponer las panes en
movimiento o permitir que objetos sean
disparados Controlar frecuentamenta y
cuando sea necesario sustituir con partes
aconsejadas por el fabdcanta
•Las cuchillas de la segadora ect_n afiladas
y pueden cortar Cubrir las hojas o Ilevar
guantes y utilizar precauciones especiales
cuando se efect0a mantanimiento sobre las
rnJsmas
•NO cambie el ajusta del regulador del motor
ni exosda su veloCidad
19

A_kBusqueeste sfmbok_que ser3elalas wecaudo-
nes de segpridadde ir,_ Quiem dedr -
liiATENCIbN!!! IIIESTE ALERTO!I! $U
SEGURIDAD ESTA COMPROMETIDA.
_at_mbreRECAUCleN:S_elwpm_e el .
de la bujiay pc_galodonde no pueoa
entraren contactocon la bujia,para evitarel
an'anquepotaccidente,durante la preparack_, el
trensporte,el ajusteo cuando se hacen
reparaelones.
J_LDVERTENCIA: Eltubode escapedel motor,
algunosde sus cons_uysates y el_
comlx_e_ detvehiculo conlJeneno
despmnden produc_osqufmicosconoeldesen el
Estadode Californiacon_ocausa de cdncer y
defectos al nadmiento u ob'osda_os
reproducUvos.
_DVERTENCIA: Los bornes,terminates y
accesonosmlatJvos de la bateda con'denenplomo
o cornpuestosde piomo,productosqulmicos
conoddos en el Estado de Californiacomocausa
de cdncery defectos al nacimientou eros da_os
repmducO_s. Laver la= rnanoe despu_ de
manlpularlos.
_PRECAUCI(_N: El silenciador y otras piezes
del motor llegan a set extremadamente
calientes durante la operacien y siguen siendo
calientes despu_s de que el motor haya
parade. Para evitar quemaduras severas,
permanezca lejos de estas _reas.
Estos accesorios estaban disponibles cuando se produjo la segadora. No son
facllltados Junto al cortacesped. Tambi_n estdn disponibles en la mayorfa de las
tiendas de Sears y en los centros de servicio. La mayorfa de las tiendas Sears
tambidn pueden mandar a pedir partes de repuesto para usted, si les proporciona el
nL_merodel modelo de su segadora. Algunos de estos accesorios tal vez no se
apliquen asu segadora.
RENDIMIENTO DE LA SEGADORA
DF.SVIADOR DE RECORTES
PARA SEGADORAS CON DESCARGA TRASERA JUEGOS PARA LA ACOLCHADORA ESTABILIZADORES
_RE_REDOR _RECOR_R _
P_A PA_
eE_ SEG_OP#_
COND_AR°_ COND_
TR._E_ LATERAL EI_AS_
MANTENIMIENTO DE LA SEGADORA
SILENCIADORES RLTROS DE AIRE BUJ[AS
CORREAS CUCHILLAS DE CUCHILLA RUEOAS DEL MOTOR
IMPORTANTE: ESTE CORTACESPED VIENE
SIN ACEITE O GASOLINA EN EL MOTOR.
Lea estas instrucciones y el manual
completamente antes de tratar de montar u
operar su segadora nueva. 2O