Craftsman 917.386081 User manual

Owner's Manual
ICRRFTSMRN°IMOWER
ROTARY LAWN
4.0 Horsepower
20" Side Discharge
Model No.
917.386081
CAUTION:
Read and follow all
Safety Rules and Instructions
before operating this equipment
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
Visit our Craftsman website: www.sears.com/craftsman

Warranty ................................................. 2
Safety Rules ........................................ 2-4
Assembly /Pre-Operation ................... 4-8
Operation ........................................... 9-11
Maintenance Schedule ........................ 12
Maintenance .................................... 12-15
Product Specifications .......................... 13
Service and Adjustments ...................... 15
Storage ............................................ 16-17
Troubleshooting .............................. 17-18
Repair Parts ..................................... 36-41
Sears Service ......................... Back Cover
LIMITED ONE YEAR WARRANTY ON CRAFTSMAN POWER MOWER
For one year from date of purchase, when this Craftsman Lawn Mower is maintained,
lubricated, and tuned up according to the operating and maintenance instructions in
the owner's manual, Sears will repair free of charge any defect in material or workman-
ship.
If this Craftsman Lawn Mower is used for commercial or rental purposes, this warranty
applies for only 90 days from the date of purchase.
This Warranty does not cover:
•Expendable items which become worn during normal use, such as rotary mower
blades, blade adapters, belts, air cleaners and spark plug.
• Repairs necessary because of operator abuse or negligence, including bent
crankshafts and the failure to maintain the equipment according to the instructions
contained in the owner's manual.
Warranty service is available by returning the Craftsman power mower to the nearest
Sears Service Center/Department in the United States. This warranty applies only
while this product is used in the United States.
This Warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
SEARS, ROEBUCKAND CO., D/817 WA, HOFFMAN ESTATES, ILLINOIS 60179
IMPORTANT: This cutting machine is capable of amputating hands and feet and
throwing objects. Failure to observe the following safety instructions could result in
serious injury or death.
_,Look for this symbol to point out
important safety precautions. It means
CAUTIONH! BECOMEALERT!!! YOUR
SAFETY IS INVOLVED.
WARNING: In order to prevent
accidental starting when setting up,
transporting, adjusting or making repairs,
always disconnect spark plug wire and
place wire where it cannot contact spark
plug.
_I,WARNING: Battery posts, terminals and
related accessories contain lead and
lead compounds, chemicals known to the
State of California to cause cancer and
birth defects or other reproductive harm.
Wash hands after handling.
_I,WARNING: Engine exhaust, some of
its constituents, and certain vehicle '_ .
components contain or emit chemicals
known to the State of California to cause
cancer and birth defects or other repro-
ductive harm. 2
=0ACAUTION: Muffler and other engine
parts become extremely hot during
operation and remain hot after engine
has stopped. To avoid severe burns on
contact, stay away from these areas.

I. GENERAL OPERATION
•Read, understand, and follow all
instructions on the machine and in the
manual(s) before starting. Be thor-
oughly familiar with the controls and
the proper use of the machine before
starting.
• Do not put hands or feet near or under
rotating parts. Keep clear of the
discharge opening at all times.
•Only allow responsible individuals,
who are familiar with the instructions, to
operate the machine.
•Clear the area of objects such as
rocks, toys, wire, bones, sticks, etc.,
which could be picked up and thrown
by the blade.
• Be sure the area is clear of other
people before mowing. Stop machine if
anyone enters the area.
• Do not operate the mower when
barefoot or wearing open sandals.
Always wear substantial foot wear.
•Do not pu_l mower backwards unless
absolutely necessary. Always look
clown and behind before and while
moving backwards.
• Do not operate the mower without
proper guards, plates, grass catcher or
other safety protective devices in place.
• See manufacturer's instructions for
proper operation and installation of
accessories. DO NOT use accessories
that are not recommended by the
manufacturer of your mower, such as
de-thatcher blade attachments, which
can be hazardous and damage the
mower.
• Stop the blade(s) when crossing gravel
drives, walks, or roads.
• Stop the engine (motor) whenever you
leave the equipment, before cleaning
the mower or unclogging the chute.
• Shut the engine (motor) off and wait
until the blade comes to complete stop
before removing grass catcher.
• Mow only in daylight or good artificial
light.
• Do not operate the machine while
under the influence of alcohol or drugs.
•Never operate machine in wet grass.
Always be sure of your footing: keep a
firm hold on the handle and walk; never
run.
• Disengage the self-propelled mecha-
nism or drive clutch on mowers so
equipped before starting the engine
(motor).
• If the equipment should start to vibrate
abnormally, stop the engine (motor)
and check immediately for the cause.
Vibration is generally a warning of
trouble.
• Always wear safety goggles or safety
glasses with side shields when operat-
ing mower.
II. SLOPE OPERATION
Slopes are a major factor related to slip
and fall accidents which can result in
severe injury. All slopes require extra
caution. If you feel uneasy on a slope, do
not mow it.
DO:
• Mow across the face of slopes: never
up and down. Exercise extreme caution
when changing direction on slopes.
• Remove obstacles such as rocks, tree
limbs, etc.
• Watch for holes, ruts, or bumps. Tall
grass can hide obstacles.
DO NOT:
•Do not trim near drop-offs, ditches or
embankments. The operator could lose
footing or balance.
•Do not trim excessively steep slopes.
• Do not mow on wet grass. Reduced
footing could cause slipping,
III. CHILDREN
Tragic accidents can occur if the operator
is not alert to the presence of children.
Children are often attracted to the
machine and the mowing activity. Never
assume that children will remain where
you last saw them.
• Keep children out of the trimming area
and under the watchful care of another
responsible adult.
• Be alert and turn machine off if children
enter the area.
• Before and while walking backwards,
look behind and down for small
children.
• Never allow children to operate the
machine.
• Use extra care when approaching blind
corners, shrubs, trees, or other objects
that may obscure vision.
3

IV. SERVICE
•Use extra care in handling gasoline
and other fuels. They are flammable
and vapors are explosive,
-Use only an approved container.
-Never remove gas cap or add fuel
with the engine running. Allow
engine to cool before refueling. Do
not smoke,
-Never refuel the machine indoors.
-Never store the machine or fuel
container inside where there is an
open flame, such as a water heater.
• Never run a machine inside a closed
area.
• Never make adjustments or repairs
with the engine (motor) running.
Disconnect the spark plug wire, and
keep the wire away from the plug to
prevent accidental starting.
• Keep nuts and bolts, especially blade
attachment bolts, tight and keep
equipment in good condition.
•Never tamper with safety devices.
Check their proper operation regularly.
•Keep machine free of grass, leaves, or
other debris build-up. Clean oil or fuel
spillage. Allow machine to cool before
storing.
•Stop and inspect the equipment if you
strike an object. Repair, if necessary,
before restarting.
•Never attempt to make wheel height
adjustments while the engine (motor) is
running.
•Grass catcher components are subject
to wear, damage, and deterioration,
which could expose moving parts or
allow objects to be thrown. Frequently
check components and replace with
manufacturer's recommended parts,
when necessary.
•Mower blades are sharp and can cut.
Wrap the blade(s) or wear gloves, and
use extra caution when servicing them.
• Do not change the engine governor
setting or overspeed the engine.
Parts packed separately in carton
(1)
Lowel
Handle (1) Engine Zone
Control Cable
(1) Discharge
Guard
C4)Wheels
4

Parts Bag contents not shown full size
(4) Wheel
Height
Adjusters
(1) Upstop
Bracket
e(l) Rope
(2) Wing Nuts
Parts Bag contents shown full size
(2) Hex Bolts 1/4-20
Upstop Bracket
[1) Hex Washer Head
Self-tapping Screw
#10-24 x 1/2
Discharge Guard
(2) Washers 3/4" Dia.
T
Rope Guide
(1) Locknut
1/4-20
©
(2) Locknuts 1/4-20 m
Wheels
(4) Flange Locknuts 3/8-16
j_ Wheel Adjusters
\\
'\
z,
_....... / (4) Locknuts
(2) Washers 1-1/4" Dia. 3/8-16 (4) Wheel Adjuster Knobs
(2) Hairpin Cotters
Handles
5

ACAUTION: Do not operate this mower
without the discharge guard or an entire
approved grass catcher in place. These
guards are for your protection and are
required by the American National
Standards Institute and Consumer
Products Safety Commission.
ACAUTION: Disconnect spark plug wire
from spark plug and place wire where it
cannot come in contact with plug.
Read these instructions and this manual
in its entirety before you attempt to
assemble or operate your new lawn
mower.
IMPORTANT: This lawn mower is
shipped WITHOUT OIL OR GASOLINE in
the engine.
Your new lawn mower has been as-
sembled at the factory with the exception
of those parts left unassembled for
shipping purposes. All parts such as nuts,
washers, bolts, etc., necessary to com-
plete the assembly have been placed in
the parts bag. To ensure safe and proper
operation of your lawn mower, all parts
and hardware you assemble must be
tightened securely. Use the correct tools
as necessary to ensure proper tightness.
TOOLS REQUIRED FOR ASSEMBLY
Asocket wrench set will make assembly
easier. Standard wrench sizes are listed.
(1) 5/16" Wrench (1) Adjustable Wrench
(1) 7/16" Wrench (1) 9/16" Wrench
(1) 1/2" Wrench (1) 3/4" Wrench
When right hand or left hand is men-
tioned in this manual, it means when you
are standing in the operating position,
behind the handle.
UNPACK CARTON
1. Remove all loose parts from carton.
2. Examine all items. Compare with list
of unassembled parts and hardware.
3. Remove lawn mower housing with
care. Avoid touching blade under
housing. Always wear gloves or other
protection when working under or
lifting mower.
ASSEMBLE LOWER HANDLE
NOTE: The holes in lower handle are off
center to allow different height positions.
1. To install lower handle onto the
handle brackets squeeze the bottom
ends of lower handle towards each
other until the lower handle will slip
onto the mounting pins.
2. Position the lower handle in the
mowing position.
3. Install the two hairpin cotters onto
mounting pins.
Mowing
position
Hairpin
Mounting=
pin LOW POSITION
(_'_ Mowing F_
', position /
,;,
HIGH POSITION
SQUEEZE
TO INSTALL
Hairl:
ASSEMBLE UPPER HANDLE
1. Position upper handle over lower
handle with small hole for mounting
up-stop bracket to left side and
assemble handle bolts and wing nuts.
Tighten securely.
ASSEMBLE UPSTOP BRACKET
2. Position upstop bracket on the left
inside of upper handle as shown.
3. Install the hex washer head screw into
the hole in up-stop bracket and upper
handle. Tighten securely.
6

AS VIEWED FROM FRONT OF MOWER
\
Hex \
washer
head \
screw
ASSEMBLE WHEELS
1. Install wheels on threaded adjuster
axle arms.
2. Secure each wheel with flanged
Iocknut. Tighten securely.
3. Assemble adjustment knobs to
adjuster levers by pressing on or
tapping lightly.
Axle arm
Flanged
Iocknut
A_ustment
knob
Wheel
ASSEMBLE ADJUSTERS TO MOWER
DECK
Look carefully at the four (4) adjuster
assemblies. Notice that there are two (2)
different types. Type I is for the right rear
and left front. Type II is for the right front
and left rear.
1. Place each adjuster in the middle
adjustment position.
2. Position appropriate adjuster at each
corner of mower.
3. Install each adjuster with adjuster bolt
and tab in deck holes as shown and
secure with 1-1/4" washer (rear
adjusters only) and 3/8-16 Iocknut.
Tighten all adjusters securely.
Type I
1-1/4" Washer (Rear Adjusters Only)
Tabhole_f._ _ _-L_--_Locknuts)) )
Type I heig
(right rear/left front) _,.J_r'_'-__ I.
Type II height adjuster _
(right front/left rear)----.,.._-_ Tab hole 7
ASSEMBLE DISCHARGE GUARD
1. Place discharge guard on top of lawn
mower discharge opening.
2. Install two (2) 1/4-20 x 3/4 hex bolts
through housing and discharge guard.
3. Install two (2) 3/4" diameter washers
and two (2) 1/4-20 Iocknuts. Tighten
securely.
Washers
Discharge guard
Hex

INSTALL CONTROL BAR
1. Position control bar so flattened
section with hole is on opposite side
of handle as up-stop bracket.
2. Insert one end of control bar into
handle hole on inside of handle.
Carefully push in on opposite end of
control bar and insert into hole on
opposite side of handle.
Control bar
Up-stop bracket
ASSEMBLE ENGINE ZONE CONTROL
CABLE TO UPPER HANDLE
Assemble cable to opposite side of up-
stop bracket.
1. Route cable below crossbar of lower
handle and up to control bar.
2. Hook "Z" bend fitting on inner wire into
hole in control bar.
3. Attach cable fitting to upper handle as
shown.
4. Secure cable to lower handle with
wire tie.
Control Upper
Upstop
racket
zone
control
cable
ASSEMBLE ENGINE ZONE CONTROL
CABLE TO ENGINE
1. Straighten cable and find the end with
the small plastic fitting.
2. Hook the "Z" bend fitting on inner wire
of cable into hole in brake arm of
engine.
3. Align the tapered end of the small
plastic fitting with the hole in the
mounting bracket and push in until
fitting snaps into place.
INSTALL STARTER ROPE
1. Put threaded end of rope guide
through hole in side of upper handle
above lower handle crossbar. Secure
with 1/4-20 Iocknut.
2. Hold control bar against upper handle
and slowly pull engine starter rope out
until rope will slip into loop of rope
guide.
Mounting
bracket
PUSH IN_
plastic fitting
Rope
guide
arm
Engine
starter rope
Lower handle
crossbar
8

KNOW YOUR LAWN MOWER
READ THIS OWNER'S MANUAl_AND ALL SAFETY RULES BEFORE OPERATING YOUR
LAWN MOWER. Compare the illustrationswith your lawn mower to familiarize yourself with
the location of various controls and adjustments. Save this manual for future reference.
These symbols may appear on your lawn mower or in literature supplied with the
product. Learn and understand their meaning.
CAUTION ENGINE ENGINE FAST SLOW CHOKE FUEL OIL DANGER, KEEP HANDS
OR WARNING ON OFF AND FEET AWAY
-Operator presence control bar
Engine zone control cable
!nut
Starter
handle Gasoline filler cap
Primer
Engine oil plu Air filter
Muffler
Housing
Discharge
guard
Wheel adjuster (on each wheel)
IMPORTANT: This lawn mower is shipped WITHOUT OIL OR GASOLINE in the engine.
MEETS CPSC SAFETY REQUIREMENTS
Sears rotary walk-behind power lawn mowers conform to the safety standards of the
American National Standards Institute and the U.S. Consumer Product Safety Commis-
sion. The blade turns when the engine is running.
Operator presence control bar -must be
held down to the handle to start the engine.
Release to stop the engine.
Starter handle -used for starting the engine. 9
Primer -pumps additional fuel from the
carburetor to the cylinder for use when
starting a cold engine.

The operationof any lawn
mowercan resultin foreign
objectsthrownintothe
eyes,whichcan resultin
severeeye damage.
Alwayswearsafetyglassesoreye
shieldswhileoperatingyour lawnmower
orperforminganyadjustmentsor repairs.
Werecommenda standardsafety
glassesor widevisionsafetymaskworn
overspectacles.
ENGINE SPEED
The engine speed was set at the factory
for optimum performance. Speed is not
adjustable.
ENGINE ZONE CONTROL
ACAUTION: Federal regulations require
an engine control to be installed on this
lawn mower in order to minimize the risk
of blade contact injury. Do not under any
circumstances attempt to defeat the
function of the operator control. The blade
turns when the engine is running.
• Your lawn mower is equipped with an
operator presence control bar which
requires the operator to be positioned
behind the lawn mower handle to start
and operate the lawn mower.
TO ADJUST CUTTING HEIGHT
Raise wheels for low cut and lower
wheels for high cut, adjust cutting height
to suit your requirements. Medium
position is best for most lawns.
•To change cutting height, squeeze
adjuster lever toward wheel. Move
wheel up or down to suit your require-
ments. Be sure all wheels are in the
same setting.
NOTE: Adjuster is properly positioned
when plate tab inserts into hole in lever.
Also, 9-position adjusters (if so equipped)
allow lever to be positioned between the
plate tabs.
LOWER WHEELS FOR HIGH CUT
_ Plate tal
RAISE WHEELS FOR LOW CUT Lever
BEFORE STARTING ENGINE
ADD OIL
Your lawnmower is shipped without oil in
the engine. For type and grade of oil to
use, see "ENGINE" in the Maintenance
section of this manual.
A CAUTION: DO NOT overfill engine with
oil, or it will smoke on startup.
1. Be sure lawnmower is level and area
around oil fill is clean.
2. Remove engine oil plug and fill to the
top slot in filler hole. Pour oil slowly.
NOTE: Allow oil to settle down into
engine for accurate reading.
3. Reinstall engine oil plug and tighten.
•Check oil level before each use. Add
oil if needed. Fill to top slot in filler
hole.
•Change the oil after every 25 hours of
operation or each season. You may
need to change the oil more often
under dusty, dirty conditions.
ADD GASOLINE
• Fill fuel tank to bottom of tank filler
neck. Do not overfill. Use fresh, clean,
regular unleaded gasoline with a
minimum of 87 octane. Do not mix oil
with gasoline. Purchase fuel in
quantities that can be used within 30
days to assure fuel freshness.
A CAUTION: Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame.
A CAUTION: Alcohol blended fuels
(called gasohol or using ethanol or
methanol) can attract moisture which
leads to separation and formation of
acids during storage. Acidic gas can
damage the fuel system of an engine
while in storage. To avoid engine
problems, the fuel system should be
emptied before storage of 30 days or
longer. Drain the gas tank, start the
engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel
next season. See Storage Instructions for
additional information. Never use engine
or carburetor cleaner products in the fuel
tank or permanent damage may occur.
10

Gasoline
filler cap
Engine
oilplug
TO START ENGINE
NOTE: Due to protective coatings on the
engine, a small amount of smoke may be
present during the initial use of the
product and should be considered
normal.
1. To start a cold engine, push primer
three (3) times before trying to start.
Use a firm push. This step is not
usually necessary when starting an
engine which has already run for a
few minutes.
2. Hold operator presence control bar
down to the handle and pull starter
handle quickly. Do not allow starter
rope to snap back.
MOWING TIPS
A CAUTION: Do not use de-thatcher
blade attachments on your mower. Such
attachments are hazardous, will damage
your mower and could void your warranty.
•Under certain conditions, such as very
tall grass, it may be necessary to raise
the height of cut to reduce pushing
effort and to keep from overloading the
engine and leaving clumps of grass
clippings. It may also be necessary to
reduce ground speed and/or run the
lawn mower over the area a second
time.
•For extremely heavy cutting, reduce the
width of cut by overlapping previously
cut path and mow slowly.
•For side discharge lawn mowers,
cutting in a counter-clockwise direction,
starting at the outside of the area to be
cut, spreads grass clippings more
evenly and puts less load on the
engine. To keep clippings off of
walkways, flower beds, etc., make the
first cuts in a clockwise direction.
• Keep top of engine around starter clear
and clean of grass clippings and chaff.
This will help engine air flow and
extend engine life.
TO STOP ENGINE
• To stop engine, release operator
presence control bar.
NOTE: In cooler weather it may be
necessary to r_peat priming steps. In
warmer weather over priming may cause
flooding and engine will not start. If you
do flood engine, wait a few minutes
before attempting to start and do not
repeat priming steps.
11

MAINTENANCE SCHEDULE /__°_ _o_X/_y
AS YOU COMPLETE ./'_'4 "/,_0_" SERVICE
REGULARSERVICE /__'4 _X_y_ DATES
Chock for Loose Fasteners _ I_
Clean/Inspect Grass Catcher
(If Equipped) I_ if#
MClean Lawn Mower v'
O Clean Under Drive Cover(Power-Propened Mowers) _,_
Check ddvo belt/pulleys
RE Power-P ropelledMowers) if
Check/Sharpen/Replace Blade I1#3
LubricationChart V'
Clean Battery/Recharge
tElectdc Start Mowers !I_
ECheck Engine Oi! Level _#'
NChange Engine Oil I_r.2
GClean Air Filter _2
i Inspect Muffler _'
NClean or Replace Spark Plug i/
EReplace AirFilter Paper Cartridge t#12
,/
1 - Change more often when operating under a heavy load or in high ambient temperatures.
2-Sewice more often when operai_ng in dirty or dusty conditions,
3 - Replace blades more often when mowing insandy soil.
4 - Charge 48 hour_ at et,,dof season.
GENERALRECOMMENDA_ONS
The warranty on this lawn mower does not
cover items that have been subjected to
operator abuse or negligence. To receive full
value from the warranty, operator must
maintain mower as instructed in this manual.
Some adjustments will need to be made
periodically to properly maintain your uniL
All adjustments in the Service and Adjust-
ments section of this manual should be
checked at least once each season.
• Once a year, replace the spark plug, clean
or replace air filter element and check
blade for wear. A new spark plug and
clean/new air filter element assure proper
air-fuel mixture and help your engine run
better and last longer.
•Follow the maintenance schedule in this
manual.
LUBRICATION CHART
(D Wheel adjuster
each wheel)
(_ Brake
spring
bracket
Engine oil
(!) Handle bracket mounting pins
BEFORE EACH USE
• Check engine oil level.
•Check for loose fasteners.
LUBRICATION
Keep unit well lubricated (See "LUBRICATION
CHART").
12
(_) Spray lubricant
(_) See "ENGINE" in Maintenance section.
IMPORTANT: Do not oil or grease
plastic wheel bearings. Viscous
lubricants will attract dust and dirt that
will shorten the life of the self-lubricat-
ing bearings. If you feel they must be
lubricated, use only a dry, powdered
graphite type lubricant sparingly.

PRODUCT SPECIFICATIONS
;erial Number:
Date of Purchase:
Gasoline Capacity/Type: 1.25 Quarts (Unleaded Regular)
Oil Type (API-SF-SJ): SAE 30 (above 32°F); SAE 5W-30 (below 32°F)
Oil Capacity: 20 Ounces
Spark Plug (Gap: .045") Champion RJ19LM4
Blade Bolt Torque: 35-40 ft. Ibs.
•The model and serial numbers will be found on a decal on the rear of the mower
housing. Record both serial number and date of purchase in space provided above.
LAWN MOWER
Always observe safety rules when perform-
ing any maintenance.
TIRES
•Keep tires free of gasoline, oil, or insect
control chemicals which can harm rubber.
• Avoid stumps, stones, deep ruts,sharp
objects and other hazards that may cause
tire damage.
BLADE CARE
For best results, mower blade must be
kept sharp. Replace bent or damaged
blades.
TO REMOVE BLADE
1. Disconnect spark plug wire from spark
plug and place wire where it cannot
come in contact with spark plug.
2. Turn lawn mower on its side. Make
sure air filter and carburetor are up.
3. Use a wood block between blade and
mower housing to prevent blade from
turning when removing blade bolt.
NOTE: Protect your hands with gloves
and/or wrap blade with heavy cloth.
4. Remove blade bolt by turning counter-
clockwise.
5. Remove blade and attaching hard-
ware (bolt, lock washer and hardened
washer).
NOTE: Remove the blade adapter and
check the key inside hub of blade
adapter. The key must be in good condi-
tion to work properly. Replace adapter if
damaged.
TO REPLACE BLADE
1. Position the blade adapter on the
engine crankshaft. Be sure key in
adapter and crankshaft keyway are
aligned.
2. Position blade on the blade adapter
aligning the two (2) holes in the blade
with the raised lugs on the adapter.
3. Be sure the trailing edge of blade
(opposite sharp edge) is up toward
the engine.
4. Install the blade bolt with the lock
washer and hardened washer into
blade adapter and crankshaft.
5. Use block of wood between blade and
lawn mower housing and tighten the
blade bolt, turning clockwise.
• The recommended tightening torque is
35-40 ft. Ibs.
IMPORTANT: Blade bolt is grade 8 heat
treated.
TO SHARPEN BLADE
NOTE: We do not recommend sharpen-
ing blade - but if you do, be sure the
blade is balanced.
Care should be taken to keep the blade
balanced. An unbalanced blade will
cause eventual damage to lawn mower
or engine.
• The blade can be sharpened with a file
or on a grinding wheel. Do not attempt
to sharpen while on the mower.
• To check blade balance, drive a nail
into a beam or wall. Leave about one
inch of the straight nail exposed. Place
center hole of blade over the head of
the nail. If blade is balanced, it should
remain in a horizontal position. If either
end of the blade moves downward,
sharpen the heavy end until the blade
is balanced.
Blad, Crankshaft
;way
Loc
Blade
Blade.
bolt Hard_
washer
13
shaft
Trailing edge Blade adapter

ENGINE
LUBRICATION
Use only high quality detergent oil rated
with API service classification SF-SJ.
Select the oil's SAE viscosity grade
according to your expected operating
temperature.
SAE VISCOSITY GRADES
C .3¢ -20 .10 O I0 40
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE
NOTE: Although multi-viscosity oils
(5W30, 10W30 etc.) improve starting in
cold weather, these multi-viscosity oils
will result in increased oil consumption
when used above 32°F. Check your
engine oil level more frequently to avoid
possible engine damage from running
low on oil.
Change the oil after every 25 hours of
operation orat least once a year if the
lawn mower is not used for 25 hours in
one year.
Check the crankcase oil level before
starting the engine and after each five (5)
hours of continuous use. Tighten oil plug
securely each time you check the oil
level.
TO CHANGE ENGINE OIL
1. Disconnect spark plug wire from spark
plug and place wire where it cannot
come in contact with spark plug.
2. Be sure lawn mower is on level
surface.
NOTE: Oil will drain more freely when
warm. Catch oil in a suitable container.
3. Remove bottom oil drain plug.
4. After oil has drained completely,
replace oil drain plug and tighten
securely.
5. Fill engine with oil. (See "ADD OIL" in
the Operation section of this manual).
6. Reconnect spark plug wire to spark
plug.
Drain plug
AIR FILTER
Your engine will not run properly and may
be damaged by using a dirty air filter.
Replace the air filter every 100 hours of
operation or every season, whichever
occurs first. Service air cleaner more
often under dusty conditions. Do not
wash air filter.
TO CHANGE AIR FILTER
1. Remove the air filter by turning
counterclockwise to the stop and pull
away from collar.
2. Remove filter from inside of cover.
3. Clean the inside of the cover and the
collar to remove any dirt accumula-
tion.
4. Insert new filter into cover.
5. Put air filter cover and filter into collar
aligning the tab with the slot.
6. Push in on cover and turn clockwise to
tighten.
Collar Clip TURN
COUNTER-
CLOCK-
WISE
TO
RE-
MOVE
Slot
Air filter TURN
Tab CLOCK*
Air filte WISE TO TIGHTEN
MUFFLER
Inspect and replace corroded muffler as it
could create a fire hazard and/or dam-
age.
SPARK PLUG
Replace spark plugs at the beginning of
each mowing season or alter every 100
hours of operation, whichever occurs first.
Spark plug type and gap setting are
shown in "PRODUCT SPECIFICATIONS"
in Maintenance section of this manual.
CLEANING
IMPORTANT: For best performance, kiip
mower housing free of built-grass and
trash. Clean the underside of your mower
after each use.
_CAUTION: Disconnect spark plug wire
from spark plug and place wire where it
cannot come in contact with the spark
plug.
•Clean the underside of your lawn
mower by scraping to remove build-up
of grass and trash.
14

•Clean engine often to keep trash from
accumulating. A clogged engine runs
hotter and shortens engine life.
• Keep finished surfaces and wheels free
of all gasoline, oil, etc.
• We do not recommend using a garden
hose to clean lawn mower unless the
electrical system, muffler, air filter and
carburetor are covered to keep water
out. Water in engine can result in
shortened engine life.
_;I,WARNING: To avoid serious injury,
before performing any service or adjust-
ments:
1. Release control bar and stop engine.
2. Make sure the blade and all moving
parts have completely stopped.
3. Disconnect spark plug wire from spark
plug and place where it cannot come
m contact with plug.
LAWN MOWER
TO ADJUST cu'n'ING HEIGHT
See "TO ADJUST CU3-1ING HEIGHT" in
the Operation section of this manual.
REAR DEFLECTOR
The rear deflector, attached between the
rear wheels of your mower, is provided to
minimize the possibility that objects will
be thrown out of the rear of the mower into
the operator's mowing position. If the
deflector becomes damaged, it should be
replaced.
DISCHARGE GUARD
The discharge guard, attached to the
discharge opening of your lawn mower, is
provided to prevent the possibility of injury
resulting from bbjects being thrown out of
the discharge opening into the operator
mowing position. If the discharge guard
becomes damaged, it should be replaced.
TO ADJUST HANDLE
The handle can be mounted in a high or
low position. The mounting holes in the
bottom of lower handle are off center for
raising or lowering the handle.
1. Remove upper handle and all parts
attached to lower handle.
2. Remove hairpin cotters from lower
handle bracket mounting pin.
3. Squeeze lower handle in to remove it
from mounting pins.
4. Turn lower handle over to raise or
lower handle.
5. Squeeze lower handle in and position
holes onto mounting pins on handle
bracket.
6. Reassemble upper handle and all
parts removed from lower handle.
\
Lower
ROTATE
Mowing
position
Hairpin
Mounting -
pin LOW POSITION
ENGINE
ENGINE SPEED
Your engine speed has been factory set.
Do not attempt to increase engine speed
or it may result in personal injury. If you
believe that the engine is running too fast
or too slow, take your lawn mower to a
Sears or other qualified service center for
repair and adjustment.
CARBURETOR
Your carburetor has a non-adjustable
fixed main jet for mixture control. If your
engine does not operate properly due to
suspected carburetor problems, take your
lawn mower to a Sears or other qualified
service center for repair and/or adjust-
ment.
IMPORTANT: Never tamper with the
engine governor, which is factory set for
proper engine speed. Overspeeding the
engine above the factory high speed
setting can be dangerous. If you think the
engine-governed high speed needs
adjusting, contact a Sears or other
qualified service center, which has proper
equipment and experience to make any
15necessary adjustments.

Immediatelyprepareyour lawnmowerfor
storageat theendoftheseasonorif the
unitwillnotbe usedfor30 daysormore.
LAWN MOWER
When lawn mower is to be stored for a
period of time, clean it thoroughly, remove
all dirt, grease, leaves, etc, Store in a
clean, dry area.
1. Clean entire lawn mower (See
"CLEANING" in the Maintenance
section of this manual).
2. Lubricate as shown in the Mainte-
nance section of this manual.
3. Be sure that all nuts, bolts, screws,
and pins are securely fastened.
Inspect moving pads for damage,
breakage and wear. Replace if
necessary.
4. Touch up all rusted or chipped paint
surfaces; sand lightly before painting.
HANDLE
You can fold your lawn mower handle for
storage.
1. Squeeze the bottom ends of the lower
handle toward each other until the
lower handle clears the handle
bracket, then move handle forward.
2. Loosen upper handle mounting bolts
enough to allow upper handle to be
folded back.
IMPORTANT: When folding the handle
for storage or transportation, be sure to
fold the handle as shown or you may
damage the control cables.
•When setting up your handle from the
storage position, the lower handle will
automatically lock into the mowing
position.
SQUEEZE
TO FOLD
Operator
control bar
Lower
FOLD
BACKWARD
Mowing
position
ENGINE
FUEL SYSTEM
IMPORTANT: It is important to prevent
gum deposits from forming in essential
fuel system parts such as carburetor, fuel
filter, fuel hose, or tank during storage.
Also, alcohol blended fuels (called
gasohol or using ethanol or methanol)
can attract moisture which leads to
separation and formation of acids during
storage. Acidic gas can damage the fuel
system of an engine while in storage.
1. Drain the fuel tank.
2. Start the engine and let it run until the
fuel lines and carburetor are empty.
•Never use engine or carburetor cleaner
products in the fuel tank or permanent
damage may occur.
•Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable
alternative in minimizing the formation of
fuel gum deposits during storage. Add
stabilizer to gasoline in fuel tank or
storage container. Always follow the mix
ratio found on stabilizer container. Run
engine at least 10 minutes after adding
stabilizer to allow the stabilizer to reach
the carburetor. Do not drain the gas tank
and carburetor if using fuel stabilizer.
ENGINEOIL
Drain oil (with engine warm) and replace
with clean engine oil. (See "ENGINE" in
the Maintenance section of this manual).
16

CYLINDER
1. Remove spark plug.
2. Pour one ounce (29 ml) of oil through
spark plug hole into cylinder.
3. Pull starter handle slowly a few times
to distribute oil.
4. Replace with new spark plug.
OTHER
•Do not store gasoline from one season
to another.
• Replace your gasoline can if your can
starts to rust. Rust and/or dirt in your
gasoline will cause problems.
•If possible, store your unit indoors and
cover it to protect it from dust and dirt.
• Cover your unit with a suitable protec-
tive cover that does not retain moisture.
Do not use plastic. Plastic cannot
breathe, which allows condensation to
form and will cause your unit to rust.
IMPORTANT: Never cover mower while
engine and exhaust areas are still warm.
_1,CAUTION: Never store the lawn mower
with gasoline in the tank inside a building
where fumes may reach an open flame or
spark. Allow the engine to cool before
storing in any enclosure.
TROUBLESHOOTING -See appropriate section in manual unless directed
to a Sears Service Center.
PROBLEM CAUSE CORRECTION
Does not start 1. Dirty air filter. 1. Clean/replace air filter.
Loss of power
2. Out of fuel.
3. Stale fuel.
4. Water in fuel.
5. Spark plug wire is
disconnected.
6. Bad spark plug.
7. Loose blade or broken
blade adapter.
8. Control bar in released
position.
9. Control bar defective.
2. Fill fuel tank.
3. Drain tank and refill with
fresh, clean fuel.
4. Drain fuel tank and
carburetor and refill tank
with fresh gasoline.
5. Connect wire to plug.
6. Replace spark plug.
7. Tighten blade bolt or
replace blade adapter.
8. Depress control bar to
handle.
9. Replace control bar.
10. Fuel valve lever (if so
equipped) in OFF position.
11 .Weak battery (if equipped).
12. Disconnected battery
connector (if equipped).
.
*
3.
4.
5.
6.
10.Turn fuel valve lever
to the ON position.
11.Charge battery.
12.Connect battery to engine.
Rear of lawn mower
housing or cutting blade
dragging in heavy grass.
Cutting too much grass.
Dirty air filter.
Buildup of grass, leaves,
and trash under mower.
Too much oil in engine.
Walking speed too fast.
1. Set to "Higher Cut"
position.
2. Set to "Higher Cut"
position.
3. Clean/replace air filter.
4. Clean underside of mower
housing.
5. Check oil level.
6. Cut at slower walking speed.
17

TROUBLESHOOTING -See appropriate section in manual unless directed
:oa Sears Service Center.
PROBLEM CAUSE CORRECTION
Poor cut- 1. Worn, bent or loose blade. 1, Replace blade. Tighten
uneven blade bolt.
2. Wheel heights uneven. 2. Set all wheels at same
height.
3. Buildup of grass, leaves 3. Clean underside of
and trash under mower, mower housing.
Excessive 1. Worn, bent or loose blade. 1. Replace blade. Tighten
vibration blade bolt.
2. Bent engine crankshaft. 2. Contact a Sears or other
qualified service center.
Starter rope Engine flywheel brake is on
hard to pull when control bar is released.
.
2.
3.
4.
Bent engine crankshaft.
Blade adapter broken.
Blade dragging in grass.
1. Depress control bar to
upper handle before
pulling starter rope.
2. Contact a Sears or other
qualified service center.
3. Replace blade adapter.
4. Move lawn mower to cut
grass or to hard surface.
Grass catcher 1. Cutting height too low. 1. Raise cutting height.
notfilling 2. Lift on blade worn off. 2. Replace blade.
(Ifsoequipped) 3. Catcher not venting air. 3. Clean grass catcher.
Hard to push 1. Raise cutting height.
1. Grass is too high or wheel
height is too low.
2. Rear of lawn mower
housing or cutting blade
dragging in grass.
3. Grass catcher too full.
4. Handle height position not
right for you.
2. Raise rear of lawn mower
housing one (1) setting
higher.
3. Empty grass catcher.
4. Adjust handle height to suit.
18

Garantt'a ........................................................ 19
Reglas de Seguridad ............................... 19-21
Montaje /Operaci6n ................................ 23-25
Operaci6n ................................................ 26-28
Mantenimiento ......................................... 29-32
Programa de Mantenimiento ......................... 29
Especificaciones del Producto ..................... 30
Servicio y Adjustes ....................................... 32
Almacenamiento ...................................... 33-34
Identificaci6n de problemas .................... 34-35
Panes de repuesto ................................. 36-41
Servicio Sears ................................ Contratapa
GARANTiA LIMITADA DE DOS AI_IOSPARA LA SEGADORA A MOTOR CRAFTSMAN
Por uno (1) aSo, a partirde la fecha de compra, cuando esta Segadora Craftsman se mantenga, lubrique
y afine segt_nlas instrucdones para la operad6n y el mantenimiento en el manual del dueSo,Sears
reparar_ gratis todo defecto en el material y la mano de obra.
Si la Segadora Craftsman se usa para fines comerciales o de ardendo, esta garantfa s61ose aplica por
noventa (90) dfas a par'drde la fecha de compra.
Esta Garantfano cubre:
•Artfculosque se desgastan durante el uso normaltalescomo las cuchillassegadorasrotatories, los
adaptadoresde la cuchilla,las correas,losfiltros de alre y las bujfas.
• Reparaciones necesariasdebido alabusoo ala negligencia del operador,incluy_ndose a los
cigOeSalesdobladosy alafalta de mantenimiento del equiposeg6n las instruccionesque se incluyen
en elmanualdeldueSo.
EL SERVIClO DE GARANTiA ESTADISPONIBLE al devolverlasegadoraa motorCraftsmanal Centre/
Departmentode ServicioSears mas cercanoen los EstadosUnidos.Esta garantfase aplicasolamente
mieetras elproductoeste en uso en los EstadosUnities.
Esta Garantfa leotorgaderechoslegalesespecificos, y puedeque tambi_n tenga otrosderechosque
varfande estadoa estado.
Sears, Roebuckand Co., D/817WA, HoffmanEstates,IL 60179 USA
IMPORTANTE: Esta maquina cortadaora es capaz de amputar las manos y los manes y los
pies y de lanzar objetos. Si no se observan las instruccionesde seguridad siguientes se pueden
producir lesiones graves o la muerte.
_Busque este sfmbolo que seSala las
precauciones de seguridad de importancia.
Quiere decir -iiiATENCION!!!iiiESTE
ALERTO[!! SU SEGURIDAD ESTA
COMPROMETIDA.
_ADVERTENCIA: Siempre desconecte el
alambre de la bujfa y p6ngalo deride no pueda
entrar en contacto con la bujia, para evitar et
arranque pot accidente, durante la
preparaci6n, el transporte, el ajuste o cuando
se hacen reparaciones.
_ADVERTENClA: Los bornes, terminales y
accesorios relativos de la baterfa contienen
plomo o compuestos de plomo, productos
qufmicos conocidos en el Estado de California
como causa de c_ncer y defectos al
nacimiento u otros daSos reproductivos.Lavar
las manos despu_s de manipularlos.
_PRECAUCI6N: El tubo de escape del
motor, algunos de sus constituyentes y
algunos componentes del vehiculo contienen
o desprenden productos quimicos conocides
en el Estado de California como causa de
cancer y defectos at nacimiento u otros da,Sos
reproductivos.
_PRECAUCI6N: El silenciador y otras
piezas del motor Uegan a sre extremadamente
calientes durante la operaci6n y siguen siendo
calientes despu_s de que el motor haya
parado. Para evitar quemaduras severas,
permanezca lejos de estas &reas.
19

I. OPERACION
•Antes de empezar, debe familiarizarse
cornpletamente con los controlea y el usa
correcto de la maquina. Para esto, debe leer
y comprender todas ias instrucciones que
aparecen en la maquina yen los manuales
de operaci6n.
•No ponga las manos o los pies cerca o
debajo de las panes rotatorias. Mant_ngase
siempre lejos de la abertura de la descarga.
•Permita que so]amente las personas
responsables que estdn familiarizadas con
las instrucciones operen la m_quina.
• Despeje el drea de objetos tales coma
piedras, juguetes, atambres, huesos, palos,
etc. que pueden set recogidos y lanzados
par las cuchillas.
•Aseg_rese que el drea no se hallen
personas, antes de segar. Pare ]a mdquina
sialguien entra en el drea.
•No opere la maquina sin zapatos o con
sandalias abiertas. P6ngase siempra
zapatos s61idos.
•No tire de la segadora hacia atrds a menos
que sea absolutamente necosario. Mire
siempre hacia abajo y hacia detrds antes y
mientras que se mueve hacia atrds.
•No opere la segadora sin los respectivos
resguardos, las placas, el recogedor de
c_sped u otros aditamentos dise ados para
su protecci6n y seguridad.
•Refidrase alas instrucciones del fabricante
para el funcionamiento e instalaci6n de
acoesorios. NO utilizar accesorios no
recomendados par el constructor de la
segadora, coma dispositivos anti-paja de la
hoja, que pueden ser peligrosos y dar_arla
segadora.
• Detenga la cuchilla olas cuchillas cuando
cruce par calzadas, calles o caminos de
grava.
• Parar el motor cada vez que se abandona
el aparato, antes de limpiar la segadora o de
remover residuoa del tuba.
• Apagar el motor y esperar hasta que las
cuchillas estdn completamente paradas
antes de remover el receptor de hierba.
•Segar solamente con luz del dia o con una
buena luz artificial.
• No opere la mdquina bajo la influencia del
alcohol o de las drogas.
• Nunca opere la maquina cuando la hierba
estd mojada. Asegl3rese siempre de tener
buena tracci6n en sus pies; mantenga el
mango firmemente y camine; nunca corra.
• Desconectar el mecanismo de propulsi6n
aut6noma o el embrague de transmisi6n en
las segadoras que Io tienen antes de poner
en marcha el motor.
• Si el equipo empezara a vibrar de una
manera anormal, pare el motor y revise de
inmediato para averiguar la causa.
Generalmente la vibraci6n suele indicar que
existe alguna averfa.
• Siempre use gafas de seguridad o anteojos
con protecci6n lateral cuando opere la
segadora.
II. OPERACION SABRE LAS CUESTAS
Los acoidentes ocurren con rods frecuencia
en las cuestas. Estos accidentes ocurren
debido a resbaladas o cafdas, las cuales
pueden resultar en graves lesiones. Operar la
recortadora en cuestas requiere mayor
concentraci6n. Si se siente inseguro en una
euesta, no la recorte.
HACER:
•Puede recortar a travds de la superficie de
la cuesta, nunca hacia arriba y hacia abajo.
Proceda con extrema precauci6n cuando
cambie de clirecci6n en las cuestas.
•Renueva todos los objetos extraSos, tales
coma guijarros, ramas, etc.
•Debe prestar atenci6n a hoyos, baches o
protuberancias. Recuerde que la hierba alta
puede esconder obst_iculos.
NO HACER"
•No recorte cerca de pendientes, zanjas o
terraplenes. El operador puede perder la
tracci6n en los pies oel equilibria.
•No recorte cuestas demasiado inclinadas.
•No recede en hierba mojada. La reducci6n
en la tracoi6n de la pisada puede causar
resbalones.
III. NllgOS
Se pueden produeir acoidentes tr_igicossi el
operador no presta atenci6n a la presencia de
los nif_os.A menudo, los ni£iosse sienten
atra{dos par la m&quina ypar la actividad de la
siega. Nunca suponga que los nihos van a
permanecer en el mismo lugar donde los via
par Oltima vez.
•Mantenga a los niSos alejados del &rea de la
siega y bajo el cuidado estricto de otra
persona adulta responsable.
•Estd alerta y apague la mdquina si hay
niSos que entran al drea.
• Antes y cuando este retrocediendo, mire
hacia atr&s y hacia abajo para verificar si
hay niSos pequeSos.
•Nunca permita que los niSosoperen la
mdquina.
•Tenga un cuidado extra cuando se acerque
a esquinas donde no hay visibilidad,a los
arbustos, drboles u arras objetos que
pueden interferir con su I{nea de visi6n.
IV. SERMICIO
• Tenga cuidado extra al manejar la gasolina
y los dem&s combustibles. Son inflamables
y los gases son explosivos.
- Use solamente un envase aprobado.
- Nunca remueva la tapa del dep6sito de
gasolina o agregue combustible con el
motor funcionando. Permita que el motor
se enfrie antes de volver a pone
combustible. No fume.
- Nunca vuelva a poner combustible en la
m&quina en recintos cerrados.
- Nunca almacene la m._quinao el envase
del combustible dentro de alg0n lugar en
donde haya una llama expuesta, tal coma
la del calentador de agua.
• Nunca haga funcionar una m&quina dentro
20 de un &rea cerrada.