Craftsman EZ3 917.37752A User manual

Owner's Manual
®
5.0 HORSEPOWER
22" REAR DISCHARGE
POWER PROPELLED
ROTARY LAWN MOWER
Model No.
9! 7.37752A
,, Safety
Assembly
Operation
Maintenance
,, EspaSol
,, Repair Parts
CAUTION:
Read and follow all
Safety Rules and instructions
before operating this equipment
Sears, Roebuck and Co,, Hoffman Estates, 1L 60179

Warranty 2 Product Specifications I1
Safety Rules 2 Service and Adjustments 14
Assembly 4 Storage t5
Operation 6 Troubfeshootir)g 16
Maintenance Schedule 10 Repair Parts 35
Maintenance I0 Parts Ordering Back Cover
LIMITED TWO YEAR WARRANTY ON CRAFTSMAN POWER MOWER
For two years from date of purchase, when thls Craftsman Lawn Mower is maintained,
lubricated, and tuned up according to the operating and maintenance instructions tn the
owner's manual, Sears will repair free of charge any defect in material or workmanship.
If this Craftsman L.awn Mower is used for commercial or rental purposes, this warranty
applies for only 90 days from the date of purchase
This Warranty does not cover:
• Expendable items which become worn during normal use, such as rotary mower
blades, blade adapters, belts, air cleaners and spark plug,
,, Repairs necessary because of operator abuse or negligence, including bent crank-
shafts and the failure to maintain the equipment according to the instructions con-
tained in the owner's manual.
Warranty service is available by returning the Craftsman power mower to the nearest
Sears Service Center/Department in the United States.. This warranty applies only while
this product is in use in the United States.
This Warranty gives you specific legal rights, and you may also have other rights which
vary from state to state. ,,
SEARS, ROEBUCK AND CO., D/8I 7 WA, HOFFMAN ESTATES, ILLINOIS 60179
TRAINING:
, Read this operatoCs manual carefully.
Become familiar with the controls and
know how to operate your mower
properly. Learn how to quickly stop
mower.
,, Do not allow children to use your mower..
Never allow adults to use mower without
proper instructions.
• Keep the area of operation clear of all
persons, especially small children and
pets°
, Use mower only as the manufacturer
intended and as described in this manual.
,, Do not operate mower if it has been
dropped or damaged in any manners.
Always have damage repaired before
using your mower.
,, Do not use accessory attachments that
are not recommended by the manufac-
turer Use of such attachments may be
hazardous.
The blade turns when the engine is
running.
PREPARATION:
• Always thoroughly check the area to be
mowed and clear it of all stones, sticks,
wires, bones, and other foreign objects..
These objects will be thrown by the blade
and can cause severe injury.
o Always wear safety glasses or eye
shields when starting and while using
your mower.
,, Dress properly. Do not operate mower
when barefoot or wearing open sandals,
Wear only solid shoes with good traction
when mowing.
o Check fuel tank before starting engine.
Do not fill gas tank indoors, when the
engine is running or when the engine is

hot.Allowtheenginetocoolforseveral
minutesbeforefillingthegastank..Clean
offanyspilledgasolinebeforestartingthe
engine.
Alwaysmakewheelheightadjustments
beforestartingyourmower.Never
attempttodothiswhiletheengineis
running.
Mowonlyindaylightorgoodartificial
light.
OPERATION:
o Keepyoureyesandmindonyourmower
andtheareabeingcut.Donotletother
interestsdistractyou,
,, Do not mow wet or slippery grass. Never
run white operating your mower. Always
be sure of your footing -- keep a firm
hold on the handles and walk,
oDo not put hands or feet near or under
rotating parts, Keep clear of the discharge
opening at all times,
o Always stop the engine whenever you
leave or are not using your mower, or
before crossing driveways, walks, roads,
and any gravel--_overed areas.
,, Never direct discharge of material toward
bystanders nor allow anyone near the
mower while you are operating it.
o Before cleaning, inspecting, or repairing
your mower, slop the engine and make
absolutely sure the blade and all moving
parts have stopped. 'Then disconnect the
spark ptug wire and keep it away from the
spark plug to prevent accidental starting.
o Do not continue to run your mower if you
hit a foreign object, Follow the procedure
outlined above, then repair any damage
before restarting and operating you
mower,
o Do not change the governor settings or
overspeed the engine. Engine damage or
personal injury may result.
o Do not operate your mower if it vibrates
abnormally. Excessive vibration is an
indication of damage; stop the engine,
safely check for the cause of vibration
and repair as required.
• Do not run the engine indoors. Exhaust
fumes are dangerous.
• Never cut grass by pulling the mower
towards you. Mow across the face of
slopes, never up and down or you migI_l
lose your footing, Do not mow exces-
sively steep slopes Use caution when
operating the mower on uneven terrain
or when changing directions -- maintain
good footing.
Never operate your mower without
proper guards, plates, grass calclter or
other safety devices in place.
MAINTENANCE AND STORAGE:
,, Check the blade and the engine mount-
ing bolts often to be sure they are
tightened properly.. I
,, Check all bolts, nuts and screws at
frequent intervals for proper tightness to
be sure mower is in safe working
condition.
,, Keep all safety devices in place and
working.
o To reduce fire hazard, keep the engine
free of grass, leaves or excessive grease
and oil.
• Check grass catcher often for deteriora-
tion and wear and replace worn bags.
Use only replacement bags that are
recommended by and comply with
specifications of the manufacturer of your
mower.
o Always keep a sharp blade on your
mower.
o Allow engine to coot before storing in any
enclosure.
•Never store mower wilh fuel in the tank
inside a building where fumes may reach
an open flame or an ignition source such
as a hot water heater, space heater,
clothes dryer, etc.
CAUTION; Always disconnect spark
plug wire and place wire where il cannot
contact spark plug in order to prevent
accidental starting when setting up,
transporting, adjusting or making repairs.
WARNING
The engine exhaust from this product
contains chemicals known to the State of
California to cause cancer, birth defects,
or other reproductive harm,
3

Theseaccessorieswereavailablewhenthislawnmowerwasproduced,Theyarealso
availableatmostSearsretailoutletsandservicecenters_.MostSearsstorescanalsoorder
repairpadsforyou,whenyou provide the model number of your lawn mower, Some of these
accessories may not apply to your lawn mower:
LAWN MOWER PERFORMANCE
CLIPPING DEFLECTOR
FOR REAR DISCHARGE LAWN MOWERS
GRASS CATCHERS
FOR
REAR DISCHARGE
LAWN MOWERS
MULCHER KITS
GRASS CATCHER S
FOR
SIDE DISCHARGE
LAWN MOWERS
STABILIZER
GAS CANS
LAWN MOWER MAINTENANCE
MUFFLERS A|R FILTERS
BLADES BLADE ADAPTERS ,WHEELS
SPARK PLUGS
ENGINE OIL
Read these instructions and this manuat in its
entirety before you attempt to assemble or
operate your new lawn mower: Your new fawn
mower has been assembled at the factory with
the exception of those parts left unassembled
for shipping purposes,. All parts such as nuts,
washers, bolts, etc. necessary to complete the
assembly have been placed in the parts bag.
To ensure safe and proper operation of your
lawn mower, all paris and hardware you
assemble must be tightened securely. Use the
correct toolsas necessary toensure proper
tightness.=
TO REMOVE LAWN MOWER FROM
CARTON
o
o
Remove loose parts included with mower,
Cut down two end comers of carton and lay
end panel down flat,
Remove all packing materials excepl
padding between upper and lower handle
and padding holding operator presence
control bar to upper handle.
,, Rotl l&wn mower out of carton and check
carton thoroughlyfor additional loose parts.
HOW TO SET UP YOUR LAWN
MOWER
TO UNFOLD HANDLE
IMPORTANT: Unfold handles carefully so as
not to pinch or damage control cables,
,, Raise handles until bwer handle section
locks into place in mowing position.
,, Remove protective padding, raise upper
handle section into place on lower handle
and tighten both handle knobs.
,, Remove handle padding holding operator
presence control bar to upper handle.
,, Your lawn mower handle can be adjusted
for your mowing comfort. Refer to "Adjusl
Handle" in the Service and Adjustment
section of this manual.

NOTE: Forshippingpurposes,therear
wheelsonyourlawnmowerarenot
adjustedtothesamepositionasthefront
wheels.Beforeoperatingmoweradjust
allwheelstothesamecuttingheight
position.
Operator presence conlrel bar
Uppper handle
Lift up
YMowing
position
Lower handle
TO INSTALL ATTACHMENTS
Your lawn mower was shipped ready to be
used as a mulcher. To convert to bagging or
discharging:
,, Open rear door and remove mulcher plug.
Stere mulcher plug in a safe place.
,, You can now install catcher or optional
clipping deflector.
,, To return to mulching operation, instalt
mulcher plug into discharge opening of
mower. Be sure all tabs are seated
properly.
Mulcher ptug'/"'_ "_
CAUTION: Do not run your lawn mower
without mulcher plug in place or approved
clipping deflector or grass catcher in place.
Never attempt to operate the lawn mower
with the rear door removed or propped
open,
frame until both ends of frame are exposed
out of the front opening.
,, Assemble lower frame to tubular frame as
shown. Be sure handle is outside of bag
and frames are fully seated as shown in
inset.
,, Slip vinyl bindings over frame.
NOTE: If vinyl bindings are too stiff, hold
them in warm water for a few minutes, If
bag gets wet, let it dry before using.
Sewn hem
Tubular_lrame,._%._f,,.:.._..._
Sewn hem Lower frame
Tubular frame
Lower flame handle
(Frames must be
fully seated)
__._ f'L .4...
%,, " ÷ 7
/Vinyt bi
TO ASSEMBLE GRASS CATCHER
,, Insert leg of tubular frame through front
opening of grass catcher and thread frame
into sewn hem of bag.
NOTE: Keep bag hem gathered on the
straight leg of the tubular frame.
o When frame comes out the other end of
sewn hem, immediately workthe end of
frame down inside the bag as sllown in
inset..
o Slide sewn hem evenly around the tubular
5

WYOURLAWN !wEn
READTHISOWNER'SMANUALANDSAFETYRULESBEFOREOPERATINGYOUR
LAWNMOWER,Comparetheillustrationswithyourfawnmowertofamiliarizeyourseif
withthelocationofvariouscontrolsandadjustments,Savethismanualforfuture
reference.
Thesesymbolsmayappearonyour lawnmoweror in literturesuppliedwith
product.Learnand understandtheir meaning.
CAUTION ENGINE ENGINE FAST SLOW CHOKE FUEL
OR WARNING ON OFF
OIL DANGER, KEEP HANDS
AND FEET AWAY
Engine zone control cable perator presence control bar
_'_"_' ...... "---_-_ Drive conLrol lever
Srarter handle
Grass catcher
Handle knob
Mulcher plug Engine oil cap wldipstick
Housing
Drive cover
Gasoline cap
Pdme Wheel adjus[er
(on each wheel)
MEETS CPSC SAFETY REQUIREMENTS
Sears rotary walk-behind power lawn mowers conform to the safety standards of the American
National Standards Institute and the US. Consumer Product Safety Commission, The blade
tums when the engine is runn[ng_
Operator presence control bar - must be
held down to the handle to start the engine
Release to stop the engine
Primer - pumps additional fuel from the
carburetor to the cylinder for use when starling
a cold engine,
Starter handle - used lor starting the engine,
Drive control lever - used to engage power-
propelled forward motion of lawn mower.
Mulcher plug - must be removed to convert to
bagging or discharging operation,

Theoperationofanylawnmowercan
resultinforeignobjectsthrownintothe
eyes, which can result in severe eye
damage. Always wear safety glasses or
eye shields while operating your lawn
mower or performing any adjustments or
repairs. We recommend a wide vision
safety mask over the spectacles or
standard safety glasses.
HOW TO USE YOUR LAWN MOWER
CAUTION: Do not run your lawn mower
without mulcher plate in place and door
closed or without an approved clipping
deflector or grasscatcher in place. Never
attempt to operate the lawn mower with
the rear door removed or propped open.
ENGINE SPEED
The engine speed was set at the factory
for optimum performance,. Speed is not
adjustable_
ENGINE ZONE CONTROL
CAUTION: Federal regulations require
an engine control to be installed on this
lawn mower in order to minimize the risk
of blade contact injury, Do not under any
circumstances attempt to defeat the
fiJncUon of the operator control, Tlie blade
turns when the engine is running
,, Your lawn mower is equipped with an
operator presence control bar which
requires the operator to be positioned
behind the lawn mower handle to start and
operate the lawn mower-
TO ADJUST CUTTING HEIGHT
o Raise wheels for low cut and lower wheels
for high cut..
,, Adjust cutting height to suit your require-
ments. Medium position is best for mosl
lawns.
,, To change cutting height, squeeze adjuster
lever toward wheel. Move wheel up or
down to suit your requirements. Be sure all
wheels are in the same setting,
NOTE: Adjuster is properly positioned
when plate tab inserts into hole in lever.
Also, 9-position adjusters (if so equipped)
allow lever to be positioned between the
plate tabs.
Piale l"ab
Lower Wheels for High Cut t ,_}_
_'_ _ __ Lever
Raise Wheels forLow Cut
TO ATTACH GRASS CATCHER
• Close the flip lid.. Flip lid must be closed
while operating lawn mower,
o Lift the rear door on the mower housing and
place 1hegrass catcher frame onto the
formed tabs on the rear door hinge bracket_
•The grass catcher is secured to tile lawn
mower housing when the rear door is
lowered onto the grass catcher frame.,
CAUTION: Do not run your lawn mower
without chipping deflector or approved
grass catcher in place, Never attempt to
operate the lawn mower with the rear door
_emoved or propped open,
Hinge Rear door
Formed
tabs
TO EMPTY GRASS CATCHER
o To remove grass catcher, release operator
presence control bar to stop engine.,
• Lift up rear door and remove the grass
catcher by the handle,
, Do not drag the bag when emptying; itwill
cause unnecessary wear.
7

DRIVECONTROL
,, Self-propellingiscontrolledbyholding
theoperatorpresencecontrolbardown
tothehandleandpushingthedrive
controlleverforwarduntilitclicks;then
releasethelever_
,, Forwardmotionwillstopwhenthe
operatorpresencecontrolbaris
released,Tostopforwardmotion
withoutstoppingengine,releasethe
operatorpresencecontrolbarslightly
untilthedrivecontroldisengages.Hold
operatorpresencecontrolbardownto
handletocontinuemowingwithoutself-
propelling,
o Tokeepdrivecontrolengagedwhen
turningcorners,pushdownonhandle
andliftfrontwheelsoffgroundwhile
turninglawnmower.
Operator presence control bar
"\\ ..__"_., .\ _ ...:.. cD;inV[reo,
To engage drive Drive control
control desengaged
BEFORE STARTING ENGINE
OIL
Your lawn mower is shipped without oiI in the
engine,
. Be sure rnower is level and area around oil
fill is clean.
o Remove engine oil cap w!dipstick and fill to
the full fine on the dipstick.
o Use 20 ozs. of oil, For type and grade doil
to use, see "ENGINE" in Maintenance
seclion of this manual.
• Pour oil slowly, Do not over fill.
° Check oil level before each use. Add oil if
needed. Fillto full fine on dipstick.
• To read proper level, tighten engine oil cap
each time.
o Reinstall engine oil cap and tighten.
. Change the oil after every 25 hours of
operation or each season. You may need
to change 1heoil more often under dusty,
dirty conditions.
ADD GASOLINE
o Fillfuel lank, Use fresh, dean, regular
unleaded gasoline wilh a minimum of 87
octane. Do not mix oil with gasoline.
Purchase fuel in quantities that can be used
within 30 days to assure fuel freshness.
IMPORTANT: When operating in
temperatures betow 32°F(0°C), use fresh,
clean winter grade gasoline to help insure
good cold weather starting.
WARNING: Experience indicates 1hatalcohol
blended fuels (called gasohol or using ethanol
or methanol) can attract moisture wt_ichleads
to separation and formation of acids during
storage.. Acidic gas can damage the fuel
system of an engine while in storage, To avoid
engine problems, the fuel system should be
emptied before storage of 30 days or longer,.
Drain the gas tank, start the engine and let it
run until the fuel lines and carburetor are
empty, Use fresh fuel next season. See
Storage Instructions for additional information.
Never use engine or carburetor cleaner
products in the fuel tank or permanent
damage may occur,
CAUTION: Fill to bottom of gas tank filler
neck,, Do not overfill,. Wipe off any spilled
oil or fuel Do not store, spill or use
gasoline near an open flame,
Gasolin filler cap Engine oil cap wf
dipstick
TO START ENGINE
,, To start a cold engine, push primer three
(3) times before trying to start. Use a firm
push. This step is not usually necessary
when starting an engine which has already
run for a few minutes.
. Hold operator presence control bar down to
lhe handle and pull starter handle quickly,
Do not allow starter rope to snap back,
o To stop engine, release operator presence
control bar.
8

NOTE: in cooler weather it may be
necessary to repeat priming steps, In
warmer weather over priming may cause
flooding and engine will not start, If you
do flood engine, wait a few minutes before
attempting to start and do not repeat
priming steps,
MOWING TIPS
o Under certain conditions, such as very tall
grass, it may be necessary to raise the
height of cut to reduce pushing effort and to
keep from overloading tile engine and
leaving dumps of grass clippings.
" For extremely heavy cutling, reduce the
width of cut and raise the rear of the lawn
mower housing one (1) wheel adjuster
setting higher than the front for better
discharge of grass
,, When using a rear discharge lawn mower in
moist, heavy grass, clumps of cut grass
may not enter the grass catcher. Reduce
ground speed (pushing speed) and!or run
the lawn mower over the area a second
time.
oIfa trail of grass clippings is left on the fight
side of a rear discharge tawn mower, mow
in a clockwise direction with a small'overlap
to collect the clippings on the next p&ss.
,, Keep top ol engine around sta,'ler clear and
clean of grass clippings and chafL This will
help engine air flow and extend engine life.
• Pores in cloth grass catchers can become
filled with dirt and dust with use and
catchers will collect less grass, "Toprevent
this, regularly hose catchers off with water
and let dry before using.
MULCHING MOWING TIPS
IMPORTANT: For best performance, keep
mower housing free of built-up grass and
trash See "Cleaning" in MAINTENANCE
section ofthis manual..
• The special mulching blade will recul the
grass clippings many times and reduce
them in size so that as they fall onto the
lawn they wil! disperse into the grass and
not be noticed. Also, the mulched grass will
biodegrade quickly to provide nutrients for
the lawn. Always mulch with your highest
engine (blade) speed as this will provide the
best recurring action of the blades.
• Avoid cutting your lawn when it iswet. Wet
grass tends to form clumps and interferes
with the mulching action° 7he best time to
mow your lawn is the early afternoon.. At
this time the grass has dned and the newly
cut area will not be exposed to the direct
sun.
o For best results, adjust the}awn mower
cutting height so that the lawn mower cuts
off only the top one-third of the grass blades.
If the lawn is overgrown itwilt be necessary
to raise the height of cut to reduce pushing
effort and to keep from overloading the
engine and leaving clumps of muiched
grass. For extremely heavy mulching,
reduce your width of ct_ by overlapping
previously cut path and mow slowly.
° Certain types of grass and grass conditions
may require that an area be mulched a
second time to completely hide the
clippings. When doing a second cut, mow
across or perpendicular to the first cut path.
° Change your cutting pattern from week to
week. Mow north to south one week then
change to east to west the next week This
wilt hetp prevent matting and graining of the
lawn.
Max t/3

MAINTENANCE SCHEDULE
FILL IN DATES
AS YOU COMPLETE
REGULAR SERVICE
Check ler Loose Fasteners
Clean!Inspect Grass Catcher
(If Equipped)
Clean Lawn Mower
Clean Under DriveCover
_power-Prope!!edMowers)
Check drive belt/pulleys
(Power, propelled Mowers)
DATES
l
v"
v'3
CheckJSh,arperdRep!aoeBlade . , i ..... " .............
Lubrication Chad $/ ...... _ t __ __
Clean BalterytRecharge
(El......eclflcSlart Mowers) _ 1/4
LEVel 1/ ....
Chan i -........... ....
Clean Air Filler . _
nSpe !M<,iii r........................ , ,V'...........
Clean or Replace Spark Plug f,/
Replace Air Fi!ler Paper Cartridge V'
I-,Change more ellen when eparatinii under a heavy !o_,d oi" tn high amblen! temperatures
2,, Servfse more oriel1 when operallng in tilt!! or dusly cof_di|+ons
3,, RopIsc_, bll_de_ mere ellen when mowing in _andy soil
4 " Ch,_ige 48 houtl el I_itd el _'oafot_
GENERAL RECOMMENDATIONS
The warranty on this lawn mower does not
cover items that have been subjected to
operator abuse or negligence.. To receive
full value from the warranty, operator must
maintain mower as instructed in this
manual.
Some adjustments wilt need to be made
periodically to properly maintain your unit.
All adjustments in the Service and
Adjustments section of this manual should
be checked at least once each season.
: Once a year, replace the spark plug,
replace air filter element and check
blade for wear,. A new spark plug and
clean/new air filter element assures
proper air-fuel mixture and helps your
engine run better and fast longer_
,, Follow the maintenance schedule in this
manual,
BEFORE EACH USE
• Check engine oil level:
: Check for loose fasteners.
LUBRICATION
Keep unit well lubricated (See "LUBRICA-
TION CHART").
LUBRICATION CHART
!_ :el f_ Rear door
mounting pin hinge
(_ Spray fubric&qt
(_ Refer to MAINTENANCE "ENGINE"
section+
IMPORTANT.' Do not oil or grease plastic
wheel bearings. Viscous lubricants will attract
dust and dirt that wilt shorten the lifeof the self
lubricating bearings. If you feet they must be
lubricated, use only a dry, powdered graphite
type lubricant sparingly
10

PRODUCT SPECIFICATIONS
MODEL NUMBER 917.37752A
SERIAL NUMBER
DATE OF PURCHASE
HORSEPOWER: 5.0
DISPLACEMENT: 11.5 CUr IN_
GASOLINE CAPACITY/'TYPE: ! ,6 QUARTS
UNLEADED REGULAR
OIL TYPE (API-SF/SGiSH): SAE 30 (ABOVE 32°F)
SAE 5W-30 (BELOW 32°F)
OIL CAPACITY: 20 OZS.
SPARK PLUG(GAP: .030") CHAMPION RJ19LM OR J19LM
VALVE CLEARANCE: INTAKE: 005"
EXHAUST: .007"
SOLID STATE IGNtTION
AIR GAP: .010 IN.
BLADE BOLT "TORQUE: 35-40 FT. LBS.
° The model and serial numbers witl be found on a decal attached to tile rear of the
lawn mower housing. Record both serial number and date of purchase in space
provided above.
LAWN MOWER
Always observe safety rules when performing
any maintenance..
TIRES
', Keep tires free of gasoline, oft,or insect
control chemicals which can harm rubber
,, Avoid stumps, stones, deep ruts, sharp
objects and other hazards that may cause
o Remove blade and attaching hardware
(bolt, tock washer and hardened washer).
NOTE: Remove the blade adapter and
check the key inside hub of blade adapter.
The key must be in good condition to work
properly, Replace adapter if damaged.
TO REPLACE BLADE
tire damage.
BLADE CARE
For best results, mower blade must be kept
sharp. Replace bent or damaged blades.
TO REMOVE BI_,DE
,, Disconnecl spark plug wire from spark plug
and place wire where itcanflot come in
contact with spark plug
o Turn lawn mower on its side. Make sure air
filter and carburetor are up
,, Use a wood block between blade and
mower housing to prevent blade from
turning when removing blade bolt.
o Protect your hands with gloves and/or wrap
blade with heavy cloth.
,, Remove blade bolt by turning counter;
clockwise. Use a 9/I6" box or open.-end
wrench.
• Position the blade adapter on the engine
crankshaft Be sure key in adapter and
crankshaft keyway are aligned,
• Position blade on the blade adapter aligning
the two (2) holes in the blade with the raised
lugs on the adapter°
o Be sure the trailing edge of blade (opposite
sharp edge) is up toward the engine.
. Install the blade bolt with the lock washer
and hardened washer into blade adapter
and cranksllaft,
,, Use b!ock of wood between blade and lawn
mower housing and tighten the blade bolt,
turning clockwise
. The recommended tightening torque is 35-
40 ft. Ibs.
IMPORTANT: Blade bolt is grade 8 heat
treated.
1I

NOTE:Wedonotrecommendsharpen-.
ingblade..butifyoudo,besuretheblade
isbalanced_
TOSHARPENBLADE
Careshouldbetakentokeeptheblade
balanced.Anunbalancedbladewill
causeeventualdamagetolawnmoweror
engine.
,, Thebladecanbesharpenedwithafileor
onagrindingwheet,Donotattemptto
sharpenwhileonthemower.
o Tocheckbladebalance,driveanailintoa
beamorwall,Leaveaboutoneincllofthe
straightnailexposed. Plade center hole of
blade over the head of the nail. if blade is
balanced, itshould remain in a horizontal
position. If either end of the blade moves
downward, sharpen the heavy end until the
blade is balanced,
Blade Crank shaft
Lock \ Trailinc Blade
washer Hardened edge adapter
washer
GRASS CATCHER
,, The grass catcher may be hosed with
water, but must be dry when used.
o Check your grass catcher often for damage
or deterioration. Through normal use itwill
wear. If catcher needs replacing, replace
only with a manufacturer approved
replacement catcher, Give the lawn mower
model number when ordering.
DRIVE WHEELS
Check front drive wheels each time before
you mow to be sure they move freely,
The wheels not turning freely means trash,
grass cuttings, etc. are in the drive wheel
area and must be cleaned to free drive
wheels.
If necessary to clean the drive wheels,
check both front wheels.
,, Remove hubcaps, hairpin cotters and
washers..
° Remove wheels from wheel adjusters.
o Remove any trash or grass cuttings from
inside the dust cover, pinion and!or drive
wheel gear teeth.
o Put wheels back in place.
o tf after cleaning, the drive wheels do not
turn freely, contact your' nearest
authorized service center
GEAR CASE.
• To keep your drive system working
properly, the gear case and area around
the drive should be kept clean and free
of trash build:up. Clean under the drive
cover twice a season.
,, The gear case is filled with lubricant to
the proper le_'el at the factory_ The only
time the lubricant needs attention is if
service has been performed on the gear
case.
, tf lubricant is required, use only Texaco
Starplex Premium 1 Grease, Part No.
750355. Do not substitute.
ENGINE
LUBRICATION
Use only high quality detergent oilrated ,with
API service classification SF,SG, or SH.
Select the oil's SAE viscosity grade accord-
ingtoyour expected operating temperature°
NOTE; Although multiwiscosity oils
(5W30, I0W30 etc.) improve starting in
cold weather, these multi-viscosity oils will
result in increased otl consumption when
used above 32°R Check your engine oil
level more frequenlJy to avoid possible
engine damage from running low on oil.
Changeafterthefirst25 hoursof operationat
leastonce ayear if thelawn mower isnotused
for25 hours inone year,
Checkthecrankcase oillevel beforestarting
theengineand after each five (5)hoursof
continuoususe._ghten oliplug securelyeach
timeyou checktheoil level.
TO CHANGE ENGINE OIL
NOTE: Before tipping lawn mower to
drain oil, drain fuel tank by running engine
until fuel tank is empty.
, Disconnect spark plug wire from spark plug
and place wire where itcannot come in
12

contactwithsparkplug.
o Removeengine oi!cap; lay aside on a clean
surface.
o Tip lawn mower on its side as .shown and
drain olf into a suitable container. Rock lawn
mower back and forth to remove any oil
trapped inside of engine..
o Wipe off any spilled oil on lawn mower and
on side of engine.
o Fill engine with oil Fill only to the "FULL"
line on tile dipstick. DO NOT oveflilt,
o Replace engine oil cap.
o Reconnect spark plug wire to spark plug
f,,.' _
Container
AIR FILTER
Your engine wilt not run properly and may be
damaged by using a dirt/air filter.
Replace the air filter every year, more often if
you mow in very' dusty, dirty conditions, Do not
wash air filter,
70 CHANGE AIR FILTER
o Loosen screw and tilt cover to remove,
,, Carefully remove cartridge,
o Clean by gently tapping on a flat
surface. If very dirty, replace cartridge_
CAUTION: Petroleum solvents, such as
kerosene, are not to be used to clean
cartridge, They may cause deterioration
of the cartridge° Do not oilcartridge, Do
not use pressurized air to clean or dry
cartridge.
Back
Cover
tabs
Li
MUFFLER
Inspect and replace corroded muffler as it
could create a fire hazard and/or damage,
SPARK PLUG
Change your spark plug each year to make
your engine start easier and run better, Set
spark plug gap at .030 inch.
CLEANING
IMPORTANT: For best perlormance, keep
mower housing free of built-up grass and
trash, Clean the underside of you_ mower a_ter
each use.
CAUTION: Disconnect spark plug wire
from spark plug and place wire where it
cannot come in contact with the spark
plug,
°Turn lawn mower on its side. Make sure air
filter and carburetor are up, Clean the
underside of your lawn mower by scraping
to remove build-up of grass and trash°
° Clean engine often to keep trash from
accumulating. A clogged engine runs hotter
and shortens engine life,
• Keep finished surfaces and wheels free of
all gasoline, oil,etc.
o We do not recommend using a garden
hose to clean lawn mower unless the
electrical system, muffler, air filter and
carburetor are covered to keep water out.
Water in engine can result in shortened
engine life.
CLEAN UNDER DRIVE COVER
Clean under drive cover at least twice a
season. Scrape underside of cover with putty
knife or similar tool to _emove any build-up of
trash or grass on underside of drive cover,
Slots
Cartridge Cover
13

CAUTION: BEFORE PERFORMING
ANY SERVICEOR ADJUSTMENTS:
,, Releasecontrolbar.
o Makesurethebladeandallmoving
partshavecompletelystopped,
o Disconnectsparkplugwirefromspark
plugandplacewhereitcannotcome
Incontactwithplug.
LAWNMOWER
TO ADJUST CUTTING HEIGHT
See "TO ADJUST CUTTING HEIGHT" in the
Operation section of this manual.
REAR DEFLECTOR
The rear deflector, attached between the rear
wheels of your lawn mower, is provided to
minimize the possibility that objects will be
thrown out the rear of the lawn mower into the
operator's mowing position. If the rear
deflector becomes damaged, it should be
replaced.
TO REMOVE/REPLACE DRIVE BELT
,, Remove drive cover. Remove belt by
pushing down on gear case pulley and roll
belt ofl_
o Turn lawn mower on its side with carburetor
and fue! cap Up,
• Remove blade..
- Remove debris shield-
. Remove belt from engine pulley on
c_ankshaft.
o Insta!l new belt by reversing above steps,
. Always use factory approved belt to assure
fit and long life.
Drive _._
cover
Belt Push
down
TO ADJUST HANDLE
Your lawn mower handle can be raised or
lowered for your mowing comfort. Four (4)
positions are available: high, medium high,
medium low and bw. Handles are shipped
mounted in the medium low position.
• To change from medium low to medium
high position, the upper and lower handle
sections will have to be turned over
.Remove cable clips.
,, Remove the controls and operator presence
control bar from the upper handle
14
°Remove the staffer rope guide from the
lower handle.
°Remove hairpin cotters,.
o Disconnect the lower handle from the
handle brackets,
o Turn the handle over and reassemble the
hairpin cotters that have been removed.
o Reassemble the starter rope guide.
o Reassemble the controls and the operator
presence cont.rolbar to the upper handle,
CAUTION: The operator presence
control bar must pivot freely to permit
blade br_<e engagement when control
bar is released.. Do not over tighten the
fasteners holding the controls to the upper
handle.
° To change from medium low to high
position only the upper handle section will
have to be turned over.
,, To change from medium low to low position,
only the lower handle section will have to be
turned over.
Shipping position
Medium low
Low
\\ ,Lower handle
Squeeze lo
remove .j j_../. \ __4-&_.j"•
Hairpin clip /Handle
bracket

ENGINE SPEED
Your engine speed has been lactory set.
Do not attempt to increase engine speed
or it may result in personal injury. If you
believe "Mat the engine is running too fast
or too slow, take your lawn mower to an
authorized service center for repair and
adjustment_
CARBURETOR
Your carburetor has a non-adjustable fixed
main jet for mixture control. If your engine
does not operate properly due to sus +
pected carburetor problems, take your
lawn mower to an authorized service
center for repair and/or adjustment.
Immediately prepare your lawn mower for
storage at the end of the season or if the unit
wilt not be used for 30 days or more.
LAWN MOWER
When lawn mower is to be stored for a period
of time, clean it thoroughly, remove all dirt,
grease, leaves, etc+ Store in a clean, dry area,
, Clean entire lawn mower (See "CLEANING"
in the Maintenance section of this manual).
° Lubricate as shown in the Maintenance
section of this manual,.
, Be sure that all nuts, bolts, screws, and pins
are securely fastened. Inspect moving
parts for damage, breakage and wear.
Replace if necessary.
, Touch up all rusted or chipped paint
surfaces; sand lightly before painting
HANDLE
You can fold your lawn mower handle for
storage.
• Squeeze the bottom ends ol the lower
handle toward each other until the lower
handle clears the handle bracket, then
move handle forward.
• Loosen upper handle mounting bolts
enough to allow upper handle to be folded
back+
IMPORTANT: When folding the handle for
storage or transportation, be sure to fotd the
handle as shown or you amy damage the
control cables.
, When setting up your handl efrom the
storage position, the lower handle will
automatically lock into the mowing position_
ENGINE
Squeeze to fold Handle
bracket
Hairpin
cotter
Upper
Operator presence control bar handle
Fold foward
tor storage
Fold
backward
Lower Mowing
handle position
FUEL SYSTEM
IMPORTAN'T: It is important to prevent gum
deposits from forming in essential fue! system'
parts such as carburetor, fuel filter, fuel hose or
tank during storage. Also, experience indicates
that alcohol blended fuels ( called gasehol or
using ethanol or methanol) can attract
moisture which leads to separation and
formation of acids during storage Acidic gas
can damage the fuel system of an engine
while in storage.
° Drain the fuel tank.
° Start the engine and let it run until the fuel
lines and carburetor are empty.
,, Never use engine or carburetor cleaner
products in the fuel tank or permanent
damage may oo.,ur.
° Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable
alternative in minimizing the formation of
fuel gum deposits during storage, Add
stabilizer to gasoline in fuel tank or
storage container. Always follow the mix
ratio found on stabilizer container. Run
engine at least !0 minutes after adding
stabilizer to allow the stabilizer to reach
the carburetor. Do not drain the gas tank
and carburetor if using fuel stabilizer.
ENGINE OIL
15

Drain oil (with engine warm) and replace with
clean engine oi!. (See "ENGINE" in the
Maintenance section of this manual).
CYLINDER
,, Remove spark plug,,
- Pour one ounce (29 ml) of oil through spark
plug hole into cylinder.
. Pull starter handle slowly a few times to
distribute oil,
,, Replace with new spark plug.
OTHER
Do not store gasoline from one season to
another,
,, Replace your gasoline can ifyour can stalts
to rust° Rust and/or dirt in your gasoline will
cause problems,
,, If possible, store your unit indoors and cover
it to give protection from dust and dirt.
,, Cover your unit with a suitable protective
cover that does not retain moisture, Do not
use plastic. Plastic cannot breathe which
allows condensation to form and wil! cause
your unit to rust,
IMPORTANT: Never cover mower while
engine and exhaust areas are still warm.
CAUTION; Never store the lawn mower
with gasoline in the tank inside a building
where fumes may reach an open flame or
spark. Allow the engine to cool before
storing in any enclosure.
TROUBLESHOOTING CHART
PROBLEM
Does not start CAUSE
,, Dirty air filter.
, Out of fuelo
.Stale fuel.
° Water in fuel.
.Spark plug wire is
disconnected,
•Bad spark plug,,
, Loose blade or broken blade
adapter.
', Control bar in released
position,
,, Control bar' defective°
CORRECTION
,, Clean/replace air filter.
,, Fill fuel tank,.
• Drain tank and refillwith
fresh clean fuel.
• Drain fuel tank and
carburetor and refilltank
with fresh gasoline.
° Connect wire to plug.
° Replace spark plug
,, lighten blade bolt or
replace blade adapter,
• Depress control bar to
handle,
,, Replace control bar.
I6

PROBLEM
Loss of power
TROUBLESHOOTING CHART
CAUSE
° Rear of lawn mower housing
or cutting blade dragging
in heavy gras&
° Cutting too much grass,
Poor cut--uneven
Excessive
vibration
Starter rope hard
to pull
Grass catcher
not filling (if so
equipped)
Hard to push
o Dirty air filter:
• Buildup of grass, leaves,
and trash under mower.
• Too much oil in engine
• Walldng speed too fast.
o Worn, bent or loose blade.
° Wheel heights uneven.
° Buildup of grass, leaves
and trash under mower°
• Worn, bent or loose b_ade.
° Bent engine crankshaI[
,, Engine flywheel brake is on
wtlen control bar is released
• Bent engine crankshaft.
° Blade adapter broken.
° Blade dragging in grass.
o Cutting height too lowo
• Uft on blade worn off,
° Catcher not venting air
° Grass is too high or wheel
height is too low,
° Rear of fawn mower
housing or blade dragging
in grass..
,, Grass catcher too full.
° Handle height position not
right for your
CORRECTION
. Set to "Higher Cut"
position
° Set to "Higher Cut"
position.
o Clean!replace air filter,
° Clean underside of mower
housing_
. Check oil level,
o Cut at slower walldng
speed, __ ......
o Replace blade.. Tighten
blade bolt.
o Set all wheels at same
height
o Clean underside of
mower housing,
° Replace blade. T_ghten
blade bolt.
° Contact an authorized
service center. ....
,, Depress control bar [o
upper handle before
pulling starter rope.
° Contact an authorized
service center.
° Replace blade adapter,
, Move lawn mower to cut
grass orto hard surface
°Raise cutting height.
,, Replace blade.
° Clean grass catcher°
° Raise cutting height,
• Raise rear of lawn mower
housing one (I) setting
higher.
° Empty grass catcher.
o Adjust handle height 1o
suit.
17

Garant(a !8 Especificaciones dee Producto 27
Reglas de Seguridad 18 Servicio y Adjustes 30
Montaje 20 Atmacenamienlo 31
Operaci6n 22 fdentificaci6n de probtemas 33
Mantenimiento 26 Partes de repues(o Vea el manual
Programa de Mantenimiento 26 ingles dei dueSo
Orden de Partes Contratapa
GARANT[A LIMITADA DE DOS AfqOS PARA LA SEGADORA A MOTOR CRAFTSMAN
Per dos (2) aSos, a pariir de tafecha de compra, cuando esta Segadora Graflsman se mantenga, lubrique
y aline segfin las instrucciones pare fa operaci6n y el mantenlmiento en el manual del dueSe, Sears
reparar_ gratis rode defecto en et material y la mane de obra
Si la Segadora Craftsman se usa pare tines comerciates o de arriendo, es'la garantfa s61ose aplica per
noventa (90) dies a partir de fa fecha de compra
Esta Garantfa no cubre:
. Artfculos qua se desgastan durante el use normal tales come las cuchillas segadoras rotatodas, los
adaptadores de la cuchiLla,las correas, los fittros de aire y las buji'as_
o Reparactones necesarias debido aIabuse o ala negligencia deI operador, incfw_ndose a los
cigfleSales doblados y a la faJtade mantenimiento del equipo seg6n Ias instrucciones que se inclwen
en el manual det dueSo,
EL SERVICtO DE GARANTI'A ESTA DfSPONfBLE al devolver fa segadpra a motor Craftsman aJcentre/
departmento de servicio Sears mas cercano en los Estados Unidos Esta garant[a se aplica solamente
mientras el producto este en use en iosEstados Unidos
Esta Garant_ale otorga detaches legales espec[ficos, y puede qua tambi_n tenga otros derechos que
varfan de estado a estadoo
Sears, Roebuck and Co,, D/817WA, Hoffrnan Estates, IL 60179 USA
Los estandrares de seguridad exigen la presencia
de! operator en los controles pare reducir a un
mtnimo el riesgo de tesionarse. Su unldad viene
equipada con dichos controles, Per ningun motive
irate del eiiminar la Iunci6n de los controles que
exigen la presencia del operador.
ENTRENAMIENTO,
,, Lea este manual del operador
cuidadosamente, Familiarfcese con los
controles y aprenda a operar su segadora en
fen'haadecuada. Aprenda a parer su segadora
_pidamente
" No permita qua los ni6os usen su segadora
Nunca permita qua ios adultos operen la
segadora sin contar con tas instrucciones
adecuadas.,
. Manlenga el &rea de operaci6n despejada
de genre, especiaImente de niSos pequeSos
yde animales dom#slicos.
,, Use la segadora sofamente pare los lines
propueslos per el fabricante y seg,Jn las
explicaciones descritas en este manuaI,
. No opera la segadora si se ha cafdo o dafado en
cualquiera form& Siempre repare los daSos
antes de usada.
•No use accesorios qua no hayan side
recomendados per el fabricante F__[use de dichos
accesorJos puede ser peligroso,
. La cuchilla gira cuando el motor est&
funcionando.
PREPARACJ6N:
. Siempre revise cuidadosamente el &rea que se
vaa segar y desp_Jela de bdas ]as piedms,
palos, alambres, huesos y otros objebs
extrahos EsIos objetos ser_n lartz.adoscon la
cuchilfa y pueden producir lesiones graves,
• Siempre use anteojos de seguridad o protecto[es
de ojos cuando arranque y durante el tiempo
qua use la segadora,
, V_stase en lorma adecuada, No opera la
segadora sin zapatos o con sandalias
mientras qua el motor est_ funcionando,
,, Siegue siempre durante el dia o con buena
luz artificial.
18

OPERACI6N:
,, Mantenga sus ojos y su mente en _a
segadora yen et area que se esta cortando.
No permita que otros intereses !o distraigan_
, No corte c#sped motado orasbaloso. Nunca
corra mientras est_ operando su segadora
Siernpre asegurese de mantener el equilibrio
- mantenga et mango agarrado firmemente y
camine
oNo #onga las manes o los pies cerca odebaio
de las partes rotatorias. MantSngase
alejado de la abe_ura de descarga en rode
memento.
,, Siernpre pare el motor cuando se vaya
ocuando no est_ usando su segadora, o
antes de atravesar las entradas para autos,
los senderos, caminos y areas cubiertas de
ripioo
o Nunca dirija la descarga del maleriat haoia
los espectadores ni permita a nadie cerca de
la segadora mientras la est_ operando
" Antes de limpiar, inspeccionar o de reparar t
a segadora, pare e_motor yest_
cornpletamente seguro de que la cuchilla y
qua todas las partes qua se rnueven se
hayan detenido. Luego, desconecte el
alarnbre de la buit'a y mant_ngalo atejado de
#sta para evitar el arranque per accidente.
* No contintJe haciendo funcionar su segadora
sile pega a un objeto extrafio.. Siga el
procedimiento descrito antertorrnente_ tuego
repare cualquier dare antes de votver a
arrancar y de operar su segadora.
,, No cambie los ajustes del regulador o
hagaque el motor ande a una vetocidad
excesiva. Se pueden producir daSos en el
motor y I esiones personales
o No opera su segadora si vibra fuera de Io
normal. La vibraci6n excesiva es una
indicaci6n de dale; pare et motor, revise en
lorma segura la causa de la vibraci6n y haga
las reparaciones segun sea necesario
- No haga funcionar el motor en
recintoscerrados. Los gases de escape son
peligrosos.
,, Nunca code eJcbsped tirando ]a segadora
hacia ustedo Siegue a tray,s de la cara de
ias pendientes, nunca hacia arriba o hacia
abaio pues puede perder el equifibrio.. No
siegue pendientes demasiado empinadas.
Tonga cuidado cuando opera ta segadora en
terreno disparejo o cuando cambie de
direcci6n- mantenga un buen equilibdo.
oNunca opera la segadora sin las
protecciones adecuadas, las planchas, el
recogedor de c_sped y otros dispositivos de
seguridad en su lugar
MANTENIMtENTO Y ALMACENAMtEN-
TO;
, Revise la cuchiila y los pernos de montaje
de! motor a menudo, para asegurarse que
est_n aprelados en fa forma adecuada.
. Revise redes los pernos, tuercas y tomillos a
intervalos frecuentes, para verilicar st est&n
apretados en trorma adecuada, y
asegurarseque la segadora se encuenlra en
condieiones de funcionamiento seguro
o Mantenga lodes los dispositivos de seguridad
en su lugar y 1is'tespara luncionar
o Para. reducir el peligro de incendio,
rnantenga el motor sin c_sped, hojas y grasa
o aceite en exceso.
oRevise el recogedor de c_sped a menudo
para veri[icar si hay deterioro y desgaste y
cambie Fasbolsas desgastadas. Use
solamente las bolsas de repuesto
recomendadas per el fabricante de su
segadora o qua cumplen con tas
especificaciones de este
,, Siempre mantenga una cuchitla afilada en su
segadorao
,, Siempre permita qua et motor se enfrie
antes de guardarla en cualquier recinto
cerrado.
* Nunca guarde ]a segadora con combustible "
en el estanque dentro de un edificio endonde
los gases pueden alcanzar una llama
expuesta o una fUente de ignici6n, tal come el
calentador de agua, la estufa de
caJefacci6n, la secadora de ropa0 e_c.
PRECAUCI(_N: Siempre desconecte e!
afarnbre de ta bujia y p6ngato dond e no pueda
enlrar en contacte con la bujia, para evitar el
arranque per accidente, durante la preparaci6n,
el transporte, ei ajus_e o cuando se hacen
reparaciones.
PRECAUCION: Es conecido per el Estado de
Ca/itomia qua los gases de escape dot motor de
este preductor contienen qu[micos los cuales a
cier_os niveles, pueden ocasionar, cancer,
defectos de nacimienlo, y otros daSos al sisterna
reproductive.
I9

Estosaccasoriosestaban disponibiescuandose produjola segadom.Tarnbi_nest&ndisponiblesen ia
mayorfa de la.stiendas de Sears y enloscentrosde se_cio, Lamayoffa de lastiendasSearstambi_n
pueden mandara pedir partesde repuestopara usted,silos prop_rcionae_nOmerodefmodetode su
segadora,Algunosde estosaccesoriostarvez no seapliquena susegadora,,
RENDtMIENTO DE LA SEGADORA ....................
DESVIADOR DE RECORTES
PARA ,.S.EGADORAS CON DESCARGA TRASERA JUEGOS PARA LA ACOLCHADORA
RECOREDORpARA _ RECOREDORpARA
SEGADORAS SEGADORAS
CON DESCARGA CON DESCARGA
TRASERA LATERAL
MANTENIMIENTO DE LA SEGADORA
ESTABIL|ZADORES
ENVASES
DE GASOUHA
S|LENCIADORES
CORREAS !
CUCHILLAS ADAPTADORES
_ECUCH=L_ RUEDAS
BUJ_AS
ACF.JTE
..........#.ELMo'roR
Lea estas Jnslruccionesy este manual
completamente antes de tralar de montar u operar
su segadom nuevao Su segadora nueva ha side
rnontada en fa f&bdca con la excepciGn de aque]las
parles que se dejaron sin montar per razones de
envio. Todas las partes come las tuercas, tas
arandelas, tos pemos, etc.,,qua son necesarias
pare completer el montaje hen side colocadas en la
bolsa de partesoPare aseguparse clue su segadora
funcione en forma segura y adecuada, todas las
partes y los adl'culos de ferrefefia qua se monten
tienen qua ser apretados seguramente. Use/as
herramientas correctas, come sea necesario, pare
asegurar que se aprieten adecuadamente.
PAPA REMOVER LA SEGADORA DE
LA CAJA DE CARTON
= Remueva las pares sueltas qua se incluyen con
la segadora_
o CoRe tas dos esquinas de los extremes de la
caja de cart6n y tienda el panel del e×tremo
piano.
. Remueva rode el material de empaque, excepto
la cuSa entre el mango superior y _1inlerior, y la
cu_ que sujeta ia bane de los control que exige
}a presencia del operader junto con el mango
superior.
Haga.rodarla segadopahaciaafuerade la caja
decart6ny rev[setacuidadosamentepare
verificarsitodavfa quedanpartessueltas
adiciona]es..
COMe PREPARAR SU SEGADORA
PAPA DESDOBLAR EL MANGO
IMPORTANTE: Despliegue el mango con muc,ho
cuidado paPano peIlizcar o daSar los cables de
control,
•Levante los mangos haste queta seccidn del
mango inferior se asegure en su lugar, en la
posici6n pare sager,
Levante la secci6n del mango superior has_,asu
lugar en el mango inferior, remueva la cuSa
protectora y apdete ambas maniilas del mango,
• Remueva la curia del mango que sujeta_a barra
de los conlrol que exJge la presencia del
operador junto con el mango superior,.
,El mango de la segadora puede ajuslarse seg0n
le acomode pare segar, Reti_rase a "AJUSTE
DEL MANGO" en la Secci6n de Servicio y
Ajustes de este manual.
20