Craftsman 113.226640 User manual

Save This Manual
For Future Reference
MODEL NO.
113.226640
SAW WITH LEGS AND
TWO TABLE EXTENSIONS
Serial
Number
Model and serial
number may be found
at the rear of the base.
You should record both
model and serial number
in a safe place for
future use.
CAUTION:
READ ALL
INSTRUCTIONS
CAREFULLY
IO-INCH
DIRECT DRIVE
TABLE SA W
•assembly
•operating
=repair parts
Sold by SEARS, ROEBUCK AND CO., Chicago, IL. 60684 U.S.A-
Part No. 62969

FULL ONE YEAR WARRANTY' ON CRAFTSMAN TABLE SAW
_fw_thm one year from the date of purchase, this Craftsman Table Saw fails due to a defect in
materia_ or workmanship. Sears will repair it, free of charge.
WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS
SERVICE CENTER/DEPARTMENT THROUGHOUT THE UNITED STATES.
This warranty applies only while this product is in use in the United States.
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
SEARS, ROEBUCK AND CO.. Dept. 698/731A, Sears Tower, Chicago, IL 60684
u j j , ...... _J_ILL--LJJJ-._.J.,--__ , ,, , - .. ,_ ....
GENERAL SAFETY mNSTRUCTIONS FOR POWER TOOLS
1. KNOW YOUR POWER TOOL
Read and understand the owner's manual and
labels affixed to the tool. Learn its application
and fimitafions as well as the specHic potential
hazards peculiar to this tool.
2. GROUND ALL TOOLS
This too_ as equipped with an approved 3-
conductor cord and a 3-prong grounding type
ptug to fit the proper grounding type receotacle
The green conductor in the cord is the
grounding w_re Never connect the green wire to
a live terminal.
3, KEEP GUARDS IN PLACE
in working order, and in proper adjustment and
alignment.
4, REMOVE ADJUSTING KEYS
AND WRENCHES
Form habit of checking to see that keys and
adjusting wrenches are removed from toot
before turning it on,
5. KEEP WORK AREA CLEAN
Cluttered areas and benches invite accidents
Floor must not be slippery due to wax or
sawdust.
6, AVOID DANGEROUS ENVIRONMENT
Don't use power tools in damp or wet locations
or expose them to rain Keep work area well
lighted, Provide adequate surrounding work
space
7, KEEP CHILDREN AWAY
AH visitors should be kept a safe distance from
work area.
8, MAKE WORKSHOP CH!LD-PROOF
.......w_th padlocks, master switches, or by
removing starter keys
9. DON'T FORCE TOOL
Jt witl do the job better and safer at the rate for
which _t was designed.
10. USE RIGHT TOOL
Don't force toot or attachment to do a job _twas
not designed for.
11, WEAR PROPER APPAREL
Do not wear loose clothing, gloves, neckties or
iewelry (rings, wrist watches) to get caught in
moving parts. Nonslip footwear is
recommended. Wear protective hair covering to
contain long hair. Roll tong sleeves above the
e|bow.
12. USE SAFETY GOGGLES (Head Protection)
Wear Safety goggles (mL_st comply w_th ANSI
Z87,1) at alJ times. Everyday eyeglasses only
have impact resistant lenses, they are NOT
safety glasses. Also. use face or dust mask if
cutting operation is dusty, and ear protectors
(plugs or muffs) during extended periods of
operation,
13. SECURE WORK
Use clamps or a vise to hold work when
practical. It's safer than using your hand, frees
both hands to operate toot.
14. DON'T OVERREACH
Keep proper footing and balance at all times.
15. MAINTAIN TOOLS WITH CARE
Keep tools sharp and clean for best and safest
performance. Follow instructions for lubricating
and changing accessories
16. DISCONNECT TOOLS
before servicing; when changing accessories
such as blades, bits, cutters, etc.
17. AVOID ACCIDENTAL STARTING
Make sure switch is in "OFF" position before
plugging in
18. USE RECOMMENDED ACCESSORIES
Consult the owner's manual for recommended
accessories. Follow the instructions that
accon_pany the accessories. The use of
improper accessories may cause hazards.
19. NEVER STAND ON TOOL
Serious injury could occur if the tool is tipped or
if the cutting tool is accidentally contacted.
Do not store materials above or near the tool
such that it is necessary to stand on the tool to
reach them.
20. CHECK DAMAGED PARTS
Before further use of the tool. a guard or other
part that is damaged should be carefully
checked to ensure that it will operate properly
and perform its intended function. Check for
alignment of moving parts binding of moving
parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A
guard or other part that is damaged should be
properly repaired or replaced.
21. DIRECTION OF FEED
Feed work into a blade or cutter against the
direction of rotation of the blade or cutter only,
22. NEVER LEAVE TOOL RUNNING
UNATTENDED
Turn Dower off, Don't _eave too_ until it comes to
a complete stop,

ADDiTiONAL SAFETY iNSTRUCTiONS FOR TABLE SAWS
WARNING: FOR YOUR OWN SAFETY, DO NOT
OPERATE YOUR SAW UNTIL iT IS COMPLETELY
ASSEMBLED AND iNSTALLED ACCORDING TO
THE INSTRUCTIONS ... AND UNTIL YOU HAVE
READ AND UNDERSTAND THE FOLLOWING.
1. GENERAL SAFETY iNSTRUCTIONS FOR
POWER TOOLS o.. SEE PAGE 2
2. GETTING TO KNOW YOUR SAW...SEE PAGE
20.
3. BASIC SAW OPERATION... SEE PAGE 23.
4. MAINTENANCE... SEE PAGE 32.
5. STABILITY OF SAW
if there is any tendency for the saw to tip over or
move during certain cutting operations such as
cutting extremely large heavy panels or long
heavy boards the saw should be bolted down
If you attach any kind of table extensions over
24" wide to either end of the saw, make sure you
either bo_t the saw to the bench or floor as
appropriate, or support the outer end of the
extension from the bench or floor as
appropriate
6. LOCATION
The saw should be positioned so neither the
operator nor a causal observer is forced to stand
in line with the saw blade
7. KICKBACKS
A "KICKBACK" occurs during a rip-type
operation when a part or all of the workpiece is
thrown back violently toward the operator
Keep your face and body to one side of the
sawblade out of line with a possible "Kickback'"
Kickbacks -- and possible injury from them --
can usually be avoided by:
A Maintaining the rip fence parallel to the
sawbtade
B Keeping the sawblade sharp Replace or
sharpen antikickback pawls when points
become dull
C Keeping sawblade guard, spreader, and
antikickback pawls in place and operating
properly The spreader must be in alignment
with the sawblade and the pawls must stop a
kickback once it has started
Check their action before ripping.
D, NOT ripping work that is twisted or warped
or does not have a straight edge to guide
along the rip fence,
E, NOT releasing work until you have pushed it
aH the way past the sawblade.
F, Using a push stick for ripping widths of 2 to 6
in., and an auxiliary fence and push block for
ripping widths narrower than 2 in. (See
"Basic Saw Operation Using The Rip Fence"
section.)
G. NOT confining the cut-off piece when
ripping or cross-cutting,
H, When ripping apply the feed force to the
section of the workpiece between the saw
blade and the rip fence,
8. PROTECTION: EYES, HANDS, FACE, EARS,
BODY
A, If any part of your saw is malfunctioning, has
been damaged or broken , . . such as the
motor switch, or other operating control, a
safety device or the power cord ... cease
operating immediately until the particular
part is proper_y repaired or replaced
B Small loose pieces of wood or other obiects
that contact the rear of the revolving b_ade
can be thrown back at the operator at
excessive speed This can usuaIiy be avoided
by keeping the guard and spreader in p}ace
for ai_ thru-sawing operations (sawing
entirely thru the work) AND by removing all
loose pieces from the table with along st_ck
of wood IMMEDIATELY after they are cut off
C Use extra caution when the guard assembly
is removed for resawing, dadoing, rabbeting,
or molding -- replace the guard as soon as
that operation is completed.
D, For rip or rip-type cuts, the following end )f a
workpiece to which a push stick or push
board is applied must be square
(perpendicular to the fence) in order that
feed pressure applied to the workpiece by
the push stick or block does not cause the
workpiece to come away from the fence, and
possibly cause a kickback.
E During rip and rtp type cuts, the workp_ece
must be held down on the tabJe and against
the fence with a push stick, push b_ock or
featherboards. A featherboard is made of
solid lumber per sketch.
&
........ K &;_:{: &_-OLI ' I
i .................... J ]
F NEVER turn the saw "ON'" before clearing
the table of all tools_ wood scraps, etc.,
except the workpiece and re!ated feed or
support dewces for the operation planned.
G. NEVER place your face or body tn tine with
the cutting toot,
H. NEVER place your fingers or hands _n the
path of the sawblade or other cuthng tool.
f NEVER reach in back of the cutting tool w_th
either hand to hold down or support the
workp_ece, remove wood scraps, or for any
other reason Avoid awkward operations ana
hand posihons where a sudden shp cou}d
cause fingers or hand to move into a
sawblade or other cutting tool
J DO NOT perform layout assembly or setup
work on the table ,while the cutting too! is
rotating
K DO NOT perform any operation
"FREEHAND" -- always use either the np
fence or the miter gauge to position and
guide the work
L NEVER use the rip fence when crosscutting
or the miter gauge when ripping DO NOT
use the rip fence as a _ength stop
Never hold onto or touch the "free end" of the
workpiece or a "free piece' that is cut off
while power is "ON" and/or the sawblade _s
rotating
M Shut "OFF" the saw and d_sconnect the
power cord when removing the table insert
changing the cutting too| remowng or
replacing the blade _uard. or ma_mg
adjustments.
3

N Provide adequate support to the rear and
sides of the saw table for wider or long
workpieces.
O. Plastic and composition (like hardboard)
materials may be cut on your saw, However,
since these are usually quite hard and
slippery, the antikickback pawls may not
stop a kickback.
Therefore, be especially attentive to
following proper set-up and cutting
procedures for ripping. Do not stand, or
permit anyone else to stand, in line with a
potential kickback.
P. If you stall or jam the sawblade in the
workpiece, turn saw "OFF", remove the
workpiece from the sawblade and check to
see if the sawblade is parallel to the miter
gauge grooves and if the spreader _s in
proper alignment with the sawblade. If
ripping at the time, check to see if the rip
fence is parallel with the sawblade. Readjust
as indicated.
Q. DO NOT remove small pieces of cut-off
material that may become trapped inside the
blade guard while the saw is running. This
could endanger your hands or cause a
kickback. Turn saw *OFF and wait until
blade stops.
R. Use extra care when ripping wood that has a
twisted grain or is twisted or bowed it may
rock on the table and/or pinch the sawblade.
9. KNOW YOUR CUTTING TOOLS
A. Dull, gummy, orJmproperlysharpened orset
cutting tools can cause material to stick, jam,
stall the saw or kickback at the operator.
Minimize potential injury by proper cutting
tool and machine maintenance.
NEVER ATTEMPT TO FREE A STALLED
SAWBLADE WITHOUT FIRST TURNING
THE SAW OFF.
B. Never use grinding wheels, abrasive cut-off
wheels, friction wheels (metal slitting
blades) wire wheels or buffing wheels.
10. USE ONLY ACCESSORIES DESIGNED FOR
THiS SAW.
11. Crosscutting operations are more convenientJy
worked and with greater safety if an auxiliary
wood facing isattached tothe mitergauge using
the holes provided. However, the facing must
not interfere with the proper functioning of the
sawblade guard ....
12. Make sure the top of the arbor or cutting tool
rotates toward you when standing in normal
operating position. Also make sure the cutting
tool, arbor collars and arbor nut are installed
properly. Keep the cutting tool as low as
possible for the operation being performed.
Keep all guards in place whenever possible.
14.
15.
17.
when ripping, use the maximum diameter blade
for which the saw is designed, since under these
conditions the spreader is nearest the blade.
Adjust table inserts flush with the table top.
NEVER operate the saw unless the proper insert
is installed.
NEVER feed material into the cutting tool from
the rear of the saw. An accident and serious
injury could result.
NEVER use another person as a substitute for a
table extension, or as additional support for a
workpiece that is longer or wider than the basic
saw table, or to assist in feeding or supporting or
pulling the workpiece.
DO NOT pull the workpiece through the
sawblade - position your body at the nose (in-
feed) side of the guard: start and complete the
cut from the same side This will require added
table support for long or wide workpeices that
extend beyond the length or width of the saw
table.
18, THINK SAFETY.
Safety is a combination of operator common
sense and alertness at all times when the saw is
being used.
19. NOTE AND FOLLOW SAFETY iNSTRUC-
TIONS THAT APPEAR ON THE FRONT OF
YOUR SAW.
IDANGER ]FORYOUR OWN SAFETY:
READ AND UNDERSTAND OWNERS MANUAL BEFORE OPERATING MACHINE.
1. WEAR SAFETy GOGGLES 5. KNOW HOW TO AVOID "KICKBACKS._
,SE SAWBLADE GUARD FOR "THRU.SAWING,' 6. DO NOT PERFORM OPERATIONS "FREEHAND."
•KEEP HANDS OUT OF PATH OF SAWBLADE, 7 NEVER REACH AROUND OR OVER SAWRLADE
4 USE A "PUSH.STICK" WHEN REQUIRED.
WARNING: USE 120 VOLT 15 AMP 8RANCH CIRCUIT AND USE 15 AMP. TIME DELAY FUSE
20. WARNING: DO NOT ALLOW FAMiLiARiTY
(GAINED FROM FREQUENT USE OF YOUR
SAW) TO BECOME COMMONPLACE.
ALWAYS REMEMBER THAT A CARELESS
FRACTION OF A SECOND IS SUFFiCiENT TO
iNFLiCT SEVERE iNJURY.
NOTE: Do not overtighten arbor nut. Use the arbor
wrench to just "snug" it.
The operation of any power tool can result in foreign
bjects being thrown into the eyes, which can result
13. Do not use any blade or other cutting tool in severe eye damage. Always wear safety goggles
marked for an operating speed less than 3450 complying with ANSI Z87.I (shown on Package)
RPM. Never use a cutting toot larger in diameter before commencing power tool operation. Safety
than the diameter for which the saw was Goggles are available at Sears retail or catalog
designed. For greatest safety and efficiency stores.

MOTOR $PECIFmCATION$ AND ELECTRICAL REQUIREMENTS
This saw is designed to use a 3450 RPM motor only.
Do not use any motor that runs faster than 3450
RPM. It is wired for operation on 110-120 volts, 60
Hz., Alternating current. IT MUST NOT BE
CONVERTED TO OPERATE ON 230 VOLTS.
WARNmNG
THE STARTING RELAY iN THiS SWITCH HOUSING
IS A GRAVITY SENSiTiVE TYPE. NEVER TURN
THE POWER ON UNTIL THE SWUTCH HOUSING
HAS BEEN ASSEMBLED ON THE FRONT FENCE
BAR AND THE SAW iS UPRIGHT IN SAWING
POSiTiON.
CONNECTING TO POWER SOURCE OUTLET
This saw must be grounded while in use to protect
the operator from electrical shock.
If power cord is worn or cut, or damaged in anyway,
have it replaced immediately.
If your saw is for use on less than 150 volts it has a
plug that looks like below.
3-PRONG PLUG
\
GROUNDING PRONG
This plug requires a mating 3-COnductor grounded
type outlet as shown.
If the outlet you are planning to use for this saw ;
_S O1
the two prong type DO NOT REMOVE OR ALT_
THE GROUNDING PRONG IN ANY MANNER Us_
an adapter as shown and always connect t_
grounding lug to a known ground.
It is recommended that you have a quaHfliec
electrician replace the TWO prong outlet wit_-_
properly grounded THREE prong outlet.
A temporary adapter as shown below is avai!abto fo
connecting plugs to 2-prong receptacles. The g roe_
grounding lug extending from the adapter must b,,
connected to a permanent ground such as to
properly grounded outlet box.
A temporary adapter as illustrated is available fo
connecting plugs to 2-prong receptacles. Tih_
temporary adapter should be used on;y unt_
properly grounded outlet can be installed by
qualified electrician.
GROUNDING LUG
__ _I"_L_-._/tl MAKE SURE THiS iS
3-PRONG _/_ L---._--- CONNECTED TO A
P,OG ,NOWNGROUND
/"EOE.,ACLE
ADAPTER
IPERLY GROUNDED
3-PRONG OUTLET
Plug power cord of fully assembled saw into 110-
120V properly grounded type outlet protected by a
15-amp. time delay or Circuit-Saver fuse or circuit
breaker.
iF YOUR ARE NOT SURE THAT YOUR OUTLET iS
PROPERLY GROUNDED, HAVE iT CHECKED BY
A QUALIFIED ELECTRiCiAN.
WARNING: DO NOT PERMIT FINGERS TO
TOUCH THE TERMINALS OF PLUG WHEN
iNSTALLiNG OR REMOVING THE PLUG TO OR
FROM THE OUTLET.
WARNING: iF NOT PROPERLY GROUNDED THiS
POWER TOOL CAN iNCUR THE POTENTIAL
HAZARD OF ELECTRICAL SHOCK PARTICU-
LARLY WHEN USED IN DAMP LOCATIONS, iN
PROXIMITY TO PLUMBING, OR OUT OF DOORS.
iF AN ELECTRICAL SHOCK OCCURS THERE IS
THE POTENTIAL OF A SECONDARY HAZARD
SUCH AS YOUR HANDS CONTACTING THE
SAWBLA DE.
This saw is equipped with a 3-conductor cord and
grounding type plug which has a grounding prong,
approved by Underwriters' Laboratories and the
Canadian Standards Association. The ground
conductor has a green lug and isattached to the tool
housing at one end and to the ground prong in the
attachment plug at the other end.
WARNING: THE GREEN GROUNDING LUC
EXTENDING FROM THE ADAPTER MUST BE
CONNECTED TO A PERMANENT GROUNE
SUCH AS TO A PROPERLY GROUNDED OUTLEI
BOX. NOT ALL OUTLET BOXES ARE PROPERL_
GROUNDED.
If you are not sure that your outlet box is proper_,
grounded, have it checked by a qualified electrician
NOTE: The adapter illustrated is for use only if yo_
already have a properly grounded 2-pror_
receptacle.
The use of any extension cord will cause some ios
of power. To keep this to a minimum and to prever_
over-heating and motor burn-out, use the tabh
below to determine the minimum wire size (AW. G
extension cord. Use only 3 wire extension DOra
which have 3 prong grounding type plugs and 3
pole receptacles which will accept the plug on th4
saw.
The motor must rotate COUNTERCLOCKW_S
when viewed from the shaft end.
1 H.P. MOTOR 1t0-120V
Extension Cord Length Wire Size A.W.G.
14
Up to 50 Ft................. 12
50 to 100 Ft................
100 - 200 Ft................ 10
8
200 - 400 Ft.................
5

CONTENTS
WARRANTY ................................. 2
GENERAL SAFETY INSTRUCTION
FOR POWER TOOLS .................... 2
ADDITIONAL SAFETY INSTRUCTIONS
FOR TABLE SAWS ...................... 3
MOTOR SPECIF_CATIONS AND ELECTRICAL
REQUIREMENTS ........................ 5
UNPACKING AND CHECKING CONTENTS . .. 6
Tools Needed .............................. 6
List o1 Loose Parts ......................... 7
ASSEMBLY .................................. 7
Assembling Steel Legs ..................... 7
Mounting Saw ............................. 8
Installing Handwheels ...................... 8
Checking Table Insert ...................... 9
Heeling Adjustment of Parallelism of
Sawbtade to Miter Gauge Groove ......... 9
Btade Tilt or Squareness of Blade to Table 10
Btade Bevatton ........................... 12
THt and Elevation Mechanism .............. 12
Attaching Table Extensions ................ 12
installing Rip Fence Guide Bars and Switch 13
Aligmng Rip Fence ........................ 16
Adjusting Rip Scale Indicator .............. !7
Installing Blade Guard .................... 18
Adjusting Miter Gauge .................... 20
GETTING TO KNOW YOUR SAW ........... 20
On-,Off Switch ............................ 20
Elevation Handwheel ...................... 21
Till Handwheel ........................... 21
Rip Fence ................................ 2t
Miter Gauge .............................. 21
B_ade Guard .............................. 22
Table Insert .............................. 22
Removing and Installing Sawblade ......... 22
Exacti-Cut ................................ 22
BASIC SAW OPERATION USING THE MITER
GAUGE ................................ 23
Work Helpers ............................. 23
Using the Miter Gauge .................... 24
Crosscutting ............................... 24
Repetitive Cutting ......................... 25
Miter Cutting ............................. 26
Bevel Crosscutting ........................ 26
Compound Miter Cutting .................. 26
BAStC SAW OPERATION USING ]HE RIP
FENCE ................................. 26
Ripping .................................. 27
Bevel Ripping ............................. 27
Cutting Panels ............................ 29
Ploughing and Molding ................... 29
Resawing ................................. 30
Rabbeting ................................ 30
Dadoing .................................. 30
Molding Cutting .......................... 31
Using Featherboards ...................... 31
MOTOR .................................... 31
MAINTENANCE ............................ 32
LUBRICATION ............................. 32
RECOMMENDED ACCESSORIES ........... 33
TROUBLE SHOOTING ...................... 33
REPAIR PARTS ............................. 36
UNPACKING AND CHECKING CONTENTS
TOOLS NEEDED
Medium Serewdrlve r
Small Screwdriver
COMBINATION SQUARE MUST BE TRUE,
STRAIGHT EDGE OF BOARD
3/4" THICK. THIS EDGE MUST
DRAW LIGHT LINE ON BE PERFECTLY STRAIGHT.
BOARD ALONG THIS EDGE, _-,
#2 Phillips Screwdriver
Pliers
"%y Combination Square 3/8 in, 7/16 in.
1/2 in. 9/16 In.
3/4 in.
Model 1 t3.226640 Table Saw is shipped complete in
one carton.
Separate all parts from packing materials and check
each one with the illustration and the list of Loose
Parts to make certain all items are accounted for,
before discarding any packing material.
If any parts are missing, do not attempt to assemble
the table saw, plug in the power cord or turn the
switch on until the missing parts are obtained and
are installed correctly.
SHOULD BE NO GAP OR OVERLAP
HERE WHEN SQUARE IS FLIPPED
OVER IN DOTTED POSITION.
Remove the protective oi! that is applied to the table
top and edges of the table. Use any ordinary
household type grease and spot remover.
CAUTION: To avoid fire or health hazard never use
gasoline, naptha or similar highly volatile solvents.
Apply a coat of automobile wax to the table.
Wipe all parts thoroughly with aclean, dry cloth.
WARNING: FOR YOUR OWN SAFETY, NEVER
CONNECT PLUG TO POWER SOURCE OUTLET
UNTIL ALL ASSEMBLY STEPS ARE COMPLETE,
AND YOU HAVE READ AND UNDERSTAND THE
SAFETY AND OPERATIONAL INSTRUCTIONS.
6

LIST OF LOOSE PARTS
Him Par_Nam_ Qty.
A Miter Gause ............................ I
B Ris Fen:e" ........................... !
CBt_'_deG,ua_da_!d Sp_eade_ ,.............. i
D HamJwhee! .............................. 2
E Rip Fe__ceGuide Ba_,_,:'a_ ............
F Rip Fe_ce Guide Sa,_RoA ............... I
G Exte__s;o_.Table ........................... 2
H Leg ...................................... 4
J Stiffe;_e_ Side ........................... 2
K Stiffener E_d ........................... 2
L R,p .... ct;Gu(. Bar wKh Ri_)Sc_i_: F_o_!)
M0wrsers Mam._ai !
BaGof Loose Pa_ts (Pa_t No 62982) ..... 1
Consisting o!:
N r I S fl
W e_ch,Sl,a ............................ 1
P W_enck, A_bo_ . ..................... I
LL Pointer, Bevel ........................ 1
'Baq oI Loose Pots (Pa_t No ,.7.;:7_
C,onsislmg of:
Q Foot Leve!i,'_(] ..................... ,4
R Nut. Hex Jam i 2-13 ................. 8
S Nut Hex 1i4-20 .................... 24
'[ Screw. r ......"" 5/8 ........ 24
_u_>SHd lJ420x _.
U Lockwashe_. Ex!e_m:d 114 ............ 24
I
M
Item Part Name Qty.
[tD NuL Sa 1/4-29 ................. 2
EE B_cket, Co_e,' Su;}po_t ............ P
IF: B_a(iket. CoirIei StlffemI/ , .............. "_
B_,, ,-_,'I '-y",', P_;_: iPa t .... 61;>qAah
Oo,"_sistin_I Ol , o Nu........... i
I_, Nut, jam 5/16-t8 .................... 3
S Nut, H_x !/4,.20 ................... 8
] Sc_ew.T_ussHd !/4-20x ! ......... 8
U Lockwastie_, Exte_nai !/4 ............. 8
ULockwashe_, Exte_p,a!5/16 ............ 3
GG ScTew. Hex 5/I6.18 x t-1/4 ............ 3
HH Washe_, 1t/32x 11i16× I 16 ........ 3
HH Washe_. 17164x 3/4 x t/16 ........... 2
*B_!] of Loose Parts (Pa,_tNo 62981) ..... 1
Coi_sJstti}{:I Of;
R Nut. Hex 3am 5/16-!8 ................. '2
SNut. !l<x I/4-20 .................... 2
U Lockwashe_. Externa_ 5/t6 ........ 4
GG Screw. Hex 5/!6-t8 x !12 .......... 2
GG Sc_,.'w.Hex 5i16. t8 x 1 ............. 2
HH " ............ 9/............. ,44._'ash_;,,I)'i64 x 16 x 3'64
HH Washe_, 2t/64 x 5/8 x t/16 ........... 4
jj Space_, Fence Guide Bar , ........... 2
*Bai of Loose Parts (Part No. 507421)
bo[tsisfing of:
S Nut Hex 5/16-18 .................... 2
S Nut, Hex 1!4-20 .................... 4
T Screw, Truss Hd. 1!4-20 x 5i8 ......... 4
U Lockwasher, External 5/16 ............ 4
U Lockwasher, External t/4 ............. 8
AA Screw, PanHd, Type:T'No. 8x3/8 ... !
GG Screw, Hex Hd. 51t6- i8 x 3t4 .......... 2
HH Washer, 17!64 x 5/8 x t/t6 .......... 8
KK Nut, Self Threading ................. 2
"These Bags are in Bag of Loose Parts No, 62982
U*<{::!":1"
' " --" HH
V............li o '_.... k::;_
(;;,
w.............. '..:........> .cc .....<,;
t: -" -. ;' :',,,,:..._ J J
X....... _ ...... <--DD "k
........::::. ......<
{_:>" ,...., £:; _i:"f }----K I'(
f',-::i..............F F ",.c_/_
.... ,.-Q
,._2i"
" .........£ ij
ASSEMBLY
ASSEMBLY OF STEEL LEG SET Description Qty.
Steel Legs ................................ 4
Assembly is best done in the location where the saw Side Stiffeners ............................ 2
witl be stationed and used. End Stiffeners ............................ 2
If Ine saw you purchased is furnished with a leg set Leveling Feet ............................. 4
fo!low the instructions below for easy assembly Hex Nuts, 1/2-13 ......................... 8
Truss Head Screws, 1/4-20 x 5/8" , ........ 24
Hex Nuts, 1/4-20 ......................... 24
I/4 I.D. External Lockwashers ............. 24
1. Locate the following:

2. Insert three truss head screws through the three
holes near the top of one leg. Place the side
stiffener up to the leg as shown so that the three
screws line up with the holes in the side stiffeners
marked with an "X" in the illustration
3. Place a Iockwasher and a hex nut on each screw
and finger tighten the hex nut.
4. Following the same procedure as above.
continue to fasten together the remaining legs
and stiffeners as illustrated.
5. Install one hex nut, 1/2-13. on each of the leveling
feet.
6. Insert each leveling foot through the hole in the
bottom of each leg so the leveling foot pad rests
on the floor.
7, Install another hex nut 1/2-13 on each of the
leveling feet.
8. After complete assembly, you may level the saw
by moving the lower nut up or down along the
threaded stud of each leveling foot. The upper nut
ts used to lock the leveling foot into position when
the saw is level.
END
STIFFENER
/ASSEMBLE SCREWS
/THROUGH HOLES
JMARKED "X"
SIDE STOFFENER
\\\
IN. HEX NUTS
MOUNTING YOUR SAW
TO THE LEG SET
1, Locate the following hardware from one of the
bags containing loose parts
Description Qty
Truss Head Screws, 1/4-20 x 5/8 ........... 4
Hex Nuts, 1/4-20 .......................... 4
1/4 I.D. External Lockwashers ............. 4
11/32 I.D. Flat Washers .................... 8
2. Place the saw on top of the leg set so that the base
of the saw lines up approximately even with the
outline of the top of the leg set.
3. From beneath the saw you wil be able to locate /
and line up the four mounting holes of the saw /
base with the proper mounting holes in the leg set /
assembly. /
!
4. Place one flat washer onto each of the four hex
head screws and insert them into each of the
mounting holes. Be sure the screws go through
the saw base holes and the leg set mounting
holes
5. Install a flat washer, Iockwasher. and a hex nut on
each of the four screws and tighten securely.
6. Level the saw to your requirements by adjusting
the leveling feet. Lock leveling feet into position.
7. Securely tighten all leg set screws and nuts.
SAW BASE 1_
TRUSS HEAD SCREW _""'_1 I
#FENER--,
II
U
8

mNSTALLING BEVEL POINTER AND
HANDWHEELS
Locate the following parts
Bevel Pointer ............................... 1
Screw, 8-32 x3/8 ........................... 1
Handwheels ................................ 2
Screw, Phillips 10-32 x 3/4 .................. 2
Lockwashers, 3/16 I.D. External ............. 2
1. Fasten bevel pointer to cradae assembly with 8-32
x 3/4 in screw, as shown. Adjustment of the
pointer may be necessary later.
2. Push handwheels onto shafts as shown and
fasten each with a10-32 x 3/4 in. screw and
Iockwasher.
LOCKWASHER
SCREW _
TILT HANDWHEEL
LOCKWASHER
SCREW T
BEVEL POINTER // SCREW
/
ELEVATION HANDWHEEL
CHECKING AND ADJUSTmNG
THE TABLE iNSERT
The table insert must be flush with the surface of the
saw table to keep the workpiece from hanging up or
binding with the sawblade as the workpiece is cut by
the sawb ade.
1. Lower sawblade beneath the table insert and
check to be sure the screw fastening the insert in
place is snug.
2. Use a straight edge to check near each of the
eight leveling tab positions to determine if the
insert is flush with the surface of the saw table at
all eight beveling tab positions.
3. If insert is not flush with table surface loosen
insert fastening screw and pull insert forward to
lift from saw table.
STRAIGHT EDGE
4. Bend tabs with pliers or tap with a hammer as
required to make the insert flush with the table
top.
\\
HEEUNG ADJUSTMENT OR PARALLEL-
iSM OF THE SAWBLADE TO THE
MITER GAUGE GROOVE
The workpiece being cut must always move in a
straight line parallel to the sawblade. Therefore.
both the miter gauge groove and the rip fence must
always be parallel with the sawblade.
If the sawblade is NOT parallel with the miter gauge
groove and the rip fence, the workpiece will bind at
one end of the cut. This is known as "heeling".
WARNING: For your own safety, turn switch "OFF"
and remove plug from power source outlet.
1. Raise blade to highest elevation.
2. Lift blade guard, if already installed, to highest
position.
3. Use chalk or another suitable marker to mark an
"X" on one of the teeth of the sawblade which is
naturally bent to the left.
MARK "X" ON TOOTH
,/
9

4. Using an accurate combination square, placethe
head of the square in the miter gauge groove and
adjust the ruler blade of the square so that the end
of the blade just touches the side of thetooth you
marked on the sawblade. Remember to keep the
head of the square flush against the miter gauge
groove.
5. Rotate the sawblade so that the "X" on the tooth
is now visible at the rear of the saw.
6. Move the combination square to the rear of the
saw and the end of the square blade should just
touch the marked tooth the same as it did at the
front of the sawblade.
7. If sawblade does not appear to be parallel with
the miter gauge groove you must adjust the
position of the sawblade by loosening the four
adjustment locking screws about 1/2 turn.
8. Loosen two pan head screws, 10-32, on the rear
skirt of the table about 1/2 turn.
9. The mechanism under the table can now be
moved sideways from above by covering the
sawblade with a piece of cardboard and shifting
the blade to the right or left as required.
10. After shifting the sawblade mechanism slightly,
recheck the position of the marked tooth of the
sawblade at both front and rear.
11. The tooth marked on the sawblade should be
parallel to the miter gauge groove after
adjustment is made.
12. Tighten all screws carefully so as not to move
sawblade out of alignment.
13. Recheck parallelism of marked sawblade tooth
to the miter gauge groove. Repeat the steps for
heeling adjustment if necessary.
1, ]SETSCREW
BLADE TILT, OR SQUARENESS
OF BLADE TO TABLE
90 ° (SQUARE) and 45 ° (BEVEL) STOP COLLARS.
When the bevel pointei _ is pointing directly to the
"O" mark on the bevel scale, the sawblade should
makea SQUARE cut 90 ° to the table.
To check for SQUARENESS:
WARNING: FOR YOUR OWN SAFETY, TURN
SWITCH "OFF" AND REMOVE PLUG FROM
POWER SOURCE OUTLET.
1. Raise blade all the way UP... raise blade guard.
2. TILT blade a few degrees to the LEFT... nowtilt
blade back to the RIGHT as far as it will go.
3. Place the square against blade. Make sure square
is not touching the TIP of one of the saw TEETH.
BEND POINTER TO "O"
/
If blade IS SQUARE to table: Check pointer
tf POINTER DOES NOT pointto the "O" mark onthe
bevel scale; Bend pointer to read "O".
POINTER
BEVEL
I" SCALE
/
ELEVATION
HANDWHEEL
1(}

if blade is NOT SQUARE to table.., the 90 ° LIMIT
STOP must be ADJUSTED.
CAUTION: Cover blade with piece of cardboard to
protect your hand.
1. Using a small size screwdriver, reach
UNDERNEATH saw and loosen BOTH setscrews
in 90 ° STOP COLLAR.
NOTE: If you can't reach the setscrews, turn the
TILT HANDWHEEL slightly,
2. ROTATE the STOP COLLAR mowng it away from
pivot nut.
3. TILT blade RIGHT or LEFT . . .checking with your
square until blade is square to table.
4. ROTATE STOP COLLAR moving it toward
PIVOT NUT until it TOUCHES the PIVOT NUT..
TIGHTEN the setscrews.
5. Check POINTER. if it DOES NOTpointtothe"O
mark on the bevel scale, bend pointer to read "O.
BLADE COVERED
WgTH PIECE OF
CARDBOARD
/
\I
SETSCREWS (2)
PIVOT NUT \\
90 °STOP COLLAR
TILT blade to LEFT as far as it will go It will stop
when the PIVOT NUT is against the 45° STOP
COLLAR.
Place an ACCURATE square against blade. Make
sure square is not touching the TIP of one of the saw
TEETH.
//
If blade is NOT 45 ° to table . . . the 45 ° STOP
COLLAR must be ADJUSTED
1. Remove Elevation Handwheel,
2. Using a small size screwdriver, reach thru curved
slot in front trip panel and loosen BOTH
setscrews in 45 ° STOP COLLAR.
NOTE: If you can't reach the setscrews, turn the
TILT HANDWHEEL slightly.
3. ROTATE the STOP COLLAR moving it IN or OUT
and TILT blade RIGHT or LEFT...checking with
your square until blade is 45 ° to table.
4. TIGHTEN the setscrews.
NOTE: If you can't reach the setscrews, turn TILT
HANDWHEEL slightly
5. Install Elevation Handwheet.
45°
STOP COLLAR
\
TiLT SCREW
l
BACK OF SAW
I!

BLADE ELEVATION
When the elevation handwheel is turned CLOCK-
WISE, until itstops, the blade must not be more than
two and five eigths (2-5/8) inches above the table. If
the blade extends more than 2-5/8 inches, the motor
could interfere with the underside of the table
causing misalignment.
With the blade extending two and five eigths (2-5/8)
inches above the table, the STOP COLLAR and
SPACER must be against the ELEVATION SCREW
PIVOT NUT. If the blade extends more than 2-5/8
inches, loosen two screws in STOP COLLAR, and
readjust it.
ELEVATION SCREW
/
f
!
/
ELEVATION SCREW
PIVOT NUT
1
\
STOP COLLAF_
TILT SCREW
\,
TILT SCREW
PIVOT NUT
TILT AND ELEVATION MECHANISM
TILT
The HANDWHEELS should turn freely without HANDWHEEI
binding, The turning action can be adjusted by 1
tiqhtening or loosening the screws in the bearing
retainer. Both handwheels must be removed to
reach the adjusting screws. _
NOTE: When adjusting the screws on the TILT
bearing retainer, hold the nut inside using a3/8 in.
wrench. The screws for the ELEVATION bearina
retainer can be reached with a small screwdrive_r
through the curved slot on the front of the saw.
ADJUST THESE
TWO SCREWS
ADJUST THESE
TWO SCREWS
ELEVATION
HANDWHEEL
1
ATTACHING AND ASSEMBLING
TABLE EXTENSIONS
From among the loose parts find the followin
hardware: (Quantity indicated is for 2 extef
Ref.
No, Description Qty.
1 Corner Support Bracket ............ 4\\ 3
2 Corner Stiffener Bracket ............ 4
3 Truss Hd. Screw, 1/4-20 x 1 ........ 16 /
_f
4 External Lockwasher, 1/4 ........... 16
5 Hex Nut, 1/4-20 .................... 16
6 Flat Washer (Dia. of Hole 17/64) .... 4
HARDWARE FOR INSTALLING
EXTENSIONS TO SAW TABLE
7 Hex Hd. Screw, 5/16-18 x 1-1/4 ..... 6
8 External Lockwasher, 5/16 .......... 6
9 Hex Nut. 5/16-18 ................... 6
10 Flat Washer (Dia. of Hole 11/32) .... 6
Assemble brackets with hardware as shown.
.TABLE EXTENSION
MOUNT TO TABLE
EXTENSION USING
)N
OPPOSITE SIDE.
__ UNDERSIDE VIEW OF
ASSEMBLED TABLE EXTENSION
12

Insertthree (3)5/16-18x 1-1/4in. long screws
throughholesin each EXTENSION then through
table, tnstall flat washer, Iockwashers, and nuts on
the screws... DO NOT TIGHTEN.
Align front edge of extension with front edge of saw
table. Pull Extension UPWARDS above table
surface . . . SLIGHTLY TIGHTEN SCREWS using
1/2 in. wrench.
Using small block of hardwood and hammer, tap
extension DOWNWARDS at front, center and rear,
until it is EVEN with table surface . . .TIGHTEN
SCREWS.
BLOCK OF WOOD
.,? ,2
ALiGNiNG EXTENSIONS
Lay REAR FENCE GUIDE BAR on table to act as a
straightedge. If outer edge of extension is higher or
lower than table surface:
1, Slightly loosen nut holding the corner support
bracket to extension using 7/16 in. wrench.
2. Move end of extension up or down until outer
edge is even with table surface . . . check with
GUIDE BAR ... tighten nuts.
3. Recheck INNERedge of extension to make sure it
has not moved .. readjust, if necessary.
4. Adjust right extension in same manner.
CHECK AT FRONT AND
REAR OF EXTENSION
/
INSTALLING RDP FENCE GUIDE BARS
AND SWITCH
1. Locate the following loose parts:
Hex head screws 5/16-18 x 3/4 ............ 2
External Iockwashers. 5/16 ................. 2
Hex Nuts 5/16-18 ......................... 4
Hex head screws, 5/16-18 x 1-1/2 ........... 2
Hex head screws 5/16-18 x 1 .............. 2
External Lockwashers 5/16 ................ 4
Spacers, 3/4 x 1/2 ......................... 2
Self threading nuts ........................ 2
Washers, 21/64 ........................... 4
Switch Assembly .......................... 1
2. Insert a 1-1/2 inch long screw, external lock-
washer, and flat washer through the sixth hole in
the front fence bar.
3. Place 1/2 inch long spacer over screw threads and
position screw through first hole on the right side
of the cast iron table skirt.
4. Use fingers to thread screw into tapped hole until
finger tight. Guide bar should be in a vertical
position.
FLAT WASHER _/1-3/4"' SCREW
_'_C_ FRONT FENCE eAR
LOCKWASHER ",-.-,___',_ 1
SPACER _6TH HOLE
r_ L.; J
13

1-t/2" HEX LOCKWASHER
HD. SCREW
5. Mount switch to guide bar with 2 hex head screws,
5/16-18 x 3/4 Iockwashers, and nuts, Securely
tighten both nuts.
6. insert 1-1/2 inch long screw through externa!
Iockwashers, fiat washer and through the second
ho_e in the guide bar. Place t/2 inch long spacer
over screw thread& Swing g uide bar to horizontal
position and screw the hex head screw into the
center hole of the table skirt. Finger tighten both
guide bar mounting screws.
FLAT WASHER
3/4" HE× HD.
SCREW .......
LOCKWASHER
LOCKWASHER
7. Insert one inch Ion.q. screws in first and third
t_oles of the rear guide bar and attach to tame
the same wav as the front bar
8inset[ ends of FENCE GUIDE BAR ROO
through holes _n bars as illustrated
NOTE: The ends of the RODare not threaded o
the SELF THREADING NUTS wdl cut threads
on the rod as they are screwed on. Just start nuts
onto ends of rod,
1 HEX HD.
SCREW
WASHER
\
LOCKWASHER \ ._;;_
'%" '_d"
SELF.THREADING NUT NUT _,__ X_-_r
BAR aOO --_/' {
REMOVE 3 SCREWS FROM
REAR OF TABLE EXTENSION
BEFORE 0NSTALLING GUIDE
9. Hold rod with one hand and with a 1/2 in, wrench
or phers start screwing on ONE of the nuts only
A TURN OR TWO screw on other nut the
same way
t0. Using TWO !/2 in. wrenches or pl_ers tighten
both of the nuts.
14

1t. Stidethe bars so that screws are r_theMIDD_E
,of the " _ -_o_ted holes
t2. Positio_ r_p fence over miler gauge groove
hoiding up the _ear end while engaging front
end with bar , • _ower fer_ce on_o tab!e
NOTE: It may be necessary to toosen fence
knob to at_ow _ence to be ir_staIled on rip raft
,J
"--::: i[
13, Move FRON"f ba_ upwards unfi! fer_ce is
approxmate!y 1,32 i_. above tab!e . , tighten
screw at left end of bar.
NOTE: Fold a piece of newsp_:_per making 8
thicknesses and p_ace betwee_ rip fence and
tab{e to act as a spacer. This wiit hold the fence
off of the table approx. IJ32 in.
!4. Adjust rear bar so that the fence is
approximately 1/32 ir_, above tabte . . .tighten
sc_ew at end of bar.
15, Replace screws in rear of table extension __. be
sure top surface of exter_sion is PARALLEL to
top surface of rea_ guide bar
8 THICKNESSES
OF PAPER
\
8 THICKNESSES
OF PAPER
16, Move fence to RIGHT edge of _ab_e . ,, make
sure it is approximately t/32 ino above table at
front and rear and tighten screws. !
_5

ALiGNiNG RiP FENCE \
The fence should slide easily along the bars and
always remain in alignment (parallel to sawblade
and miter gauge grooves).
The alignment is maintained by a spring underneath
the rip fence which bears against the front guide
bar.
To move the fence, loosen the lock handle and
grasp the fence with one hand at the front.
\
For very close adjustments, grasp the guide bar with
both hands and move the fence with your thumbs.
Place fence on saw but DO NOT LOCK IT. _--_
Move the REAR END of the fence slightly to the right
or left . ..when you release it, the fence should
"spring" back to its original position.
If it does not, the spring pressure must be
INCREASED.

1.Loosenthescrews.
2.MoveSpringslightlytowardfrontoffence.
NOTE:Applyingacoatofpastewaxtotherailswill
allowfenceto bemovedmoreeasily.
Ifthefencedoesnotslideeasilyalongthebars,the
pressureofthespringcanbeREDUCED.
1.Loosenthescrews.
2.Movespringslightlytowardrearof fence.. .
tighten screws.
SPRING
SCREWS
SLIDE SPR_NG TO
ADJUST PRESSURE
The r_p fence must be PARALLEL with the sawblade
and miter gauge grooves.. Move fence until it is
along side of groove. Do NOT LOCK IT. It should be
parallel to groove. If it is not:
1. Loosen the two "Hex Head Screws.
2. Hold fence head tightly against bar.., move end
of fence so that it is parallel with groove.
3. Alternately tighten the screws.
\\
FENCE HEA_
ADJUSTING RiP SCALE INDICATOR
1. Turn ELEVATION HANDWHEEL clockwise until
blade is up as high as (t will go.
IMPORTANT: BLADE must be SQUARE (90 °) to
TABLE, in order to ALIGN rip fence.
2. Using a rule, position fence on right side of
sawblade 2 in. from the sides of the teeth . . .
tighten lock handle.
3. Loosen screw holding the indicator.., adjust so
that it points to "2" on the r{p scale.., tighten
screw.
NOTE: If you cannot adjust indicator so that it
points to "2", loosen the screws holding the front
guide bar and move the guide bar. \\
LOCK HANDi
_7

iNSTALLiNG BLADE GUARD
1. From among the loose parts find the hardware
as sh own.
SQUARE NUT K_FSPREADER SUPPORT
_ __.r-- SPREADER BRACKET
TRUSS HEAD--.._ "-" ---'
SCREW _ __._._"'__ /SPREADER CLAMP
SOCKET HEAD I_l _. If J WING NUT 1/4-20
SETSCREW _ _J_ o_ /
7/8 IN, LONG _ _,,_ _ /
FLAT WASHER _J_ /(_
17/64 iN. HOLE _ _
HEX NUT---_ LOCKWASHER
EXT. 1/4 IN,
2. Position SPREADER SUPPORTon rod until it is
even with the end of the rod.
\
BLADE
WITH TABLE
\_RE NUT _
SPREADER _ --
BRACKET
soc
HEAD
SETSCREW-_
FLAT R _
WASHE (_
LOCKWASHER
HEX NUT_
18

5.Layapieceofflatstraightwoodandasquareon
sawtableandrotatetheSPREADERSUPPORT
unti thebracketis alignedwithsquare.
6.MAKESUREENDOFSUPPORT,BRACKET
AND RODAREEVEN. . . usingan 1/8in.
setscrewwrench,TIGHTENTHESETSCREWS
ONLY.
/
TIGHTEN
SETSCREW ONLY
ENDS OF SUPPORT
AND BRACKET TO
BE EVEN WITH
END OF ROD
SPACE EQUAL TO APPROX.
KERF OD3 THICKNESSES OF PAPER
the heS re derr ustcut the C|,
PARALLEL to the sawblade and in the MIDDLE of . , ADE
NOTE: The spreader is thinner than the width of the
KERF by approxirnately six thic knesses of paper. SPREADE/_/'_[ . . _'ii i
SPACE'EQUAL TO APPROX.
3 THICKNESSES OF PAPER
LOOKING DOWN ON SAW
7. Make two folds in a small piece (6 x 6 in.) of
ordinary NEWSPAPER making three
thicknesses. The folded paper will be used as a
"spacing gauge". /I
J
8. Raise blade to max mum height and make sure
blade is square to the saw table.
9. Install the SPREADER CLAMP. Place spreader
between spreader clamp and bracket, Move
forward until all three are in line, TIGHTEN
WINGSCREWS,
10. Lift up both ANTIKICKBACK PAWLS ... insert
one of the setscrew wrenches or a pencil in the
notches to hold the pawls out of the way.
11. Lay a piece of straight flat wood against the
sawblade. Insert folded paper between spreader
and strip of wood.
12. MAKE SURE THE HEX NUTS UNDERNEATH
ARE LOOSE.
13. Hold the spreader tightly against the wood and
make sure the wood is against the saw blade.
TIGHTEN THE HEX NUTS.
This will align the spreader in the middle of the
cut (KERF) made by sawblade.
THREE
THICKNESSES
OF PAPER
NUT.J
SPREADER
CLAMP
ANTIKICKBACK PIECE OF
PAWLS STRAIGHT WOOD
/HOLD WOOD !
TIGHTLY AGAINST
BLADE
SPREADER
BRACKET
HOLD SPREADER
TIGHTLY AGAINST WOOD

ADJUSTING MITER GAUGE __ (_, ._..WARNING: FOR YOUR OWN SAFETY, TURN "_._, _._ PG
SWITCH "OFF" AND REMOVE PLUG FROM SQUARE__
POWER SOURCE OUTLET BEFORE MAKING ANY
ADJUSTMENTS,
MITER GAUGE
NOTE: The graduations on the miter gauge provide
accuracy for average woodworking. In some cases
where extreme accuracy is required when making
angle cuts, for example, make a trial cut and then
recheck it with an accurate square or protractor.
If necessary, the miter gauge head can be swiveled
slightly to compensate for any inaccuracy.
The HEAD should be SQUARE (90°) with the bar
when the pointer points to "O".
To check for squareness, place an accurate square
on the miter gauge. If the head is NOT SQUARE with
the bar:
1. Loosen the ock knob
.=---LOCK KNOB
_INTER
2. Position the head square with the bar .tighten
the lock knob.
3. Loosen the screw and adjust the pointer, so it
points to zero.
The swiveling movement of the head can be
adjusted by tightening or loosening the set screw
located in side of the head using the 1/8 in. setscrew
wrench.
GETTmNG TO KNOW YOUR SAW
ANTIKICKBACK
MITER GAUGE 6BLADE GUARD 8 PAWLS
LOCK KNOB SAW RLAD 4
\SPREADER RIP FENCE
5 MITER GAUGE //
INSERT HOLES FOR
ATTACHING
FACING
9 E_
3 TILT HANDWHEEL
\
2 RIP FENCE
HANDWHEEL LOCK KNOB
/
/
/]
ON-OFF
SWITCH
1ON-OFF SWITCH
CAUTION: Before turning switch on, make sure the
blade guard is correctly installed and operating
properly.
The On-Off Switch has a locking feature. THIS
FEATURE IS INTENDED TO PREVENT
UNAUTHORIZED AND POSSIBLE HAZARDOUS
USE BY CHILDREN AND OTHERS.
A. TO turn saw ON... stand to either side ofthe
blade never in line with it... insert finger
under switch lever and pull END of lever out.
@
KEY
(YELLOW PLASTIC)
2O