Craftwell CUT'N'BOSS User manual

TM automatic
embosser & die cutter
USER MANUAL
TM
CREATE A BEAUTIFUL LIFE

D
C
A
B
IN THE BOX
GETTING STARTED
Cut’n’Boss machine
(7) Embossing Folders
(12) Cutting Dies
Platforms
(2) Platform A
(1) Platform B
(1) Platform D
Magnetic Shim
Metal Adapter Plate
User Manual
Power Adaptor
Position the Cut’n’Boss on a at & dry surface.
Connect the power adaptor to the power cord (A).
Connect the power cord to the Cut’n’Boss (B).
Connect the power plug to a grounded power outlet (C).
Press the power button to turn on (D).

OPERATING YOUR CUT’N’BOSSTM
Press the power button to turn on; the power button
will light up.
Guide the correct platform combination into the front of
the machine.
It will automatically activate and the platform
combination will feed through.
The machine will stop automatically when it reaches
the end of the platform combination.
Remove the platforms once the motor stops running.

USING EMBOSSING FOLDERS
Platform A
Embossing Folder
+ Material
Platform A
Platform D
Position material inside the embossing folder.
Position the embossing folder between platforms ‘A’ & ‘A’.
Stack the combination onto platform ‘D’.
Keeping the platform combination straight, guide it into
the Cut’n’Boss with a steady forward motion.
Release the platforms when the rollers begin pulling
them into the machine.
Remove the platforms once the motor stops running.
Tips: For best results, experiment with scrap paper rst.
For greater pressure, insert a piece of paper between
platforms ‘A’ & ‘D’.

USING CRAFTWELLTM CUTTING DIES
Platform A
Platform B
Platform A
Material
Cutting Die
Platform D
Position the cutting die, blade side up, smooth side
sitting on platform ‘D’.
Position the material over the cutting die then place
platform combination ’A’,‘B’,‘A’ on top of the material.
Keeping the platform combination straight, guide it into
the Cut‘n’Boss with a steady forward motion.
Release the platforms when the rollers begin pulling
them into the machine.
Remove the platforms once the motor stops running.
Optional: Place the magnetic shim between platform
‘D’ & the cutting die if more pressure is needed.
Important: Never place the magnetic shim or platform
‘B’ as the top or bottom layer of the platform combination

USING CRAFTWELLTM CUTTING DIES
WITH METAL ADAPTER PLATE
Platform A
Platform B
Platform A
Metal Adapter Plate
Materials
Cutting Die
Platform D
When cutting multiple layers of material, you may use the
metal adapter plate to increase cutting pressure.
Position the cutting die , blade side up, smooth side sitting on
platform ‘D’.
Position the multiple layers of material over the cutting die
then place platform combination ’A’,‘B’,‘A’ & metal adapter
plate on top of the material.
Keeping the platform combination straight, guide it into the
Cut‘n’Boss with a steady forward motion.
Release the platforms when the rollers begin pulling them
into the machine.
Remove the platforms once the motor stops running.
Optional: Place the magnetic shim between platform ‘D’ &
the cutting die if more pressure is needed.
Important: Never place the magnetic shim or platform
‘B’ as the top or bottom layer of the platform combination

USING OTHER BRANDS
Platform A
Platform B
Platform A
Material
Cutting Die
Magnetic Shim
Platform D
Spellbinders
Cutting Dies
AccuQuilt
Go Dies
Platform A
Platform A
Material
Cutting Die
Sizzix
Cutting Dies
Platform A
Platform B
Platform A
Material
Cutting Die
Visit craftwellusa.com to view more platform combinations for other brands
Important: When using AccuQuilt Go dies or Sizzix cutting dies,
do not have fabric hang over the dies or risk jamming the machine.

TROUBLESHOOTING
If the machine does not turn on, check that the power cord is securely
connected to the power adapter and that the adapter light is on.
To remove jammed platforms, press and hold the power button until
the reverse feature engages and the platforms are released.
If the emboss or cut is not deep enough, try adding a shim.
To minimize warping of platforms, periodically rotate and turn the platforms over.
If the platforms are rejected from the device, check if too much material
has been placed for cutting or embossing.
If the material has not been cut properly, check that the cutting die
has not been damaged.
CAUTION
Do not remove platforms until the motor has automatically shut off.
Do not allow children to operate the Cut’n’Boss machine unsupervised.
Keep hands away from platforms & parts in motion.
Forcing platforms & materials through the Cut’n’Boss will cause damage to
your machine and may void the warranty.
Do not leave objects inside the Cut’n’Boss machine when not in use.
Do not disable the safety sensors to override the motor control.
Do not use the Cut’n’Boss for 60 minutes of continuous use without
proper cool down.
Always power off you machine when not in use.
Allow the Cut’n’Boss to cool down for 15 minutes before re-using.
The Cut’n’Boss is designed for home and recreation use.
Only clean the Cut’n’Boss with a soft, dry cloth. Do not use abrasive cleaners,
spray cleaners, or chemical cleaners on the machine.

LIMITED WARRANTY
Craftwell Inc warrants that the Cut’n’Boss and any Cut’n’Boss parts and consumables (”Products”) will be free
from defects in material and workmanship.
This one year warranty is expressly limited to manufacturing defects. Craftwell will repair or replace a defective Product
without charge with proof of purchase within the warranty period. If the Product is damaged due to misuse or neglect,
the warranty is null and void.
This limited warranty excludes professional or commercial use, and applies only to Products purchased from Craftwell or
an authorized Craftwell distributor.
TO THE FULLEST EXTENT PERMITTED BY LAW,THESE WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO,THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE AND NON-INFRINGEMENT. SOME STATES DO NOT ALLOW LIMITATIONS ON IMPLIED WARRANTIES,
SO THE ABOVE LIMITATION MAY NOT APPLY TO ALL PURCHASERS. IN SUCH EVENT, THE TERM OF SUCH IMPLIED
WARRANTIES ARE LIMITED TO THE LIMITED WARRANTY PERIOD IDENTIFIED IN THE ABOVE PARAGRAPH. THIS LIMITED
WARRANTY IS VOID IF THE LABEL BEARING THE PRODUCT’S SERIAL NUMBER IS REMOVED OR ALTERED. ANY TECHNICAL
OR OTHER SUPPORT PROVIDED BY CRAFTWELL IS “AS IS” AND WITHOUT WARRANTIES OF ANY KIND. SOME STATES DO
NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO
ALL PURCHASERS.
Exclusive Remedies
Remedies under this limited warranty are limited, at Craftwell’s sole discretion, to replacement or repair of
defective Product/parts at Craftwell’s expense. All defective Products/parts replaced under this limited warranty
become the property of Craftwell. Craftwell will repair or replace defective Product/parts with new Product/parts,
or used Product/parts that are at least functionally equivalent to the replaced Product/parts. If a Product/part is
determined not to be defective, Craftwell will return the Product/part to purchaser without replacement or repair.
Unless otherwise required by law, this is purchaser’s sole and exclusive remedy for breach of this limited warranty.
Exceptions
Craftwell does not warrant that the Products will meet specic requirements of purchaser or end user or that it will
operate error-free or uninterrupted.This limited warranty does not cover Product defects or failure resulting from:
(1) improper or unreasonable use or maintenance; (2) failure to follow operating instructions; (3) business or
commercial use; (4) accident; (5) improper storage or operating conditions, including, but not limited to, excess
moisture, lightning, power surges and connections to improper voltage supply; (6) unauthorized alteration or
modication of original condition; (7) inadequate packing or shipping by purchaser; (8) alteration, loss of,
damage to, or corruption of stored data; or (9) use with non-Craftwell products that cause damage to the
Products.
Limitation of Liability
CRAFTWELL IS NOT LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, CONSEQUENTIAL, OR PUNITIVE DAMAGES,
INCLUDING, BUT NOT LIMITED TO, LOST PROFITS, LOST REVENUES OR LOST SAVINGS, REGARDLESS OF CAUSE OR LEGAL
THEORY, EVEN IF IT HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN ANY EVENT OF LIABILITY,
CRAFTWELL’S LIABILITY WILL NOT EXCEED THE AMOUNT OF THE PRICE PAID BY PURCHASER FOR PRODUCT. SOME STATES
DO NOT ALLOW EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION MAY NOT APPLY TO ALL PURCHASERS.
Governing Law and Venue
The laws of the State of New York will govern the validity, interpretation and enforcement of this limited warranty
and any claims between the parties, without regard to conicts of law principles. Venue for any dispute arising
under this limited warranty or any claims between the parties will exclusively be a state or federal court of
competent jurisdiction located in Queens, New York. The United Nations Convention on Contracts for the
International Sale of Goods is specically excluded and will not apply.All claims against Craftwell will be brought
within two (2) years from purchaser’s date of purchase, or one (1) year from the date of the occurrence,
whichever is shorter.
Obtaining Warranty Service
To obtain warranty service, the purchaser shall contact Craftwell Customer Service at [phone] or by visiting
www.craftwellusa.com, and adhere to the instructions provided by Craftwell Customer Service. Purchaser shall
return or ship the defective Product/parts to Craftwell, freight and all fees, including, but not limited to, duty, tax
and freight (“Shipping Fees”), prepaid by purchaser. Purchaser remains responsible for Product/parts while in
transit to and from Craftwell. Product/parts shall be accompanied, to the extent possible, by: (1) proof of
purchase; (2) Return Merchandise Authorization number (RMA #), which must be clearly displayed on the outside
of the shipping carton or a similar package affording an equal degree of protection; and (3) written document
with (i) clear explanation of problem, (ii) date of purchase, (iii) name and address of Craftwell Seller, and (iv)
model and serial number of Product. Craftwell will ship repaired or replaced Product/parts to purchaser, freight
prepaid, unless Product/parts are determined not to be defective by Craftwell, or purchaser is outside of the US,
in which case purchaser is responsible for all Shipping Fees. Repair or replacement of Product/part does not
extend the original limited warranty period.

See our full selection of embossing folders
at www.craftwellusa.com
embossing folder
collection

Introducing...
pocket die
collections
Visit www.craftwellusa.com for the
full selection of Teresa CollinsTM pocket dies!

TM automatic
embosser & die cutter
TM
Embossing folders
Cutting Dies &
Die Sets
Extra Platforms
Featured Craft
Project Ideas
...and more!
Look for our...
Visit us at www.craftwellusa.com
for exciting new products & ideas!
Follow us!
The Cut’n’Boss logo & mark are trademarks of Craftwell Inc.
Designed in the USA •Manufactured in China
888-315-8885
129-09 26th Avenue, Suite 405
College Point, NY 11354