Crane DEPA Nopped E4 Series User manual

www.cranecpe.com
ASSEMBLY INSTRUCTIONS
DEPA® Closed Surface Diaphragms
Series Nopped E4®
brands you trust.

www.cranecpe.com
2
Replacing the diaphragms
In addition to the following assembly steps, please also
refer to the information contained within the DEPA®
Installation, Operation and Maintenance Manual (IOM).
1. Disassembling the old diaphragms
Disassemble suction- and discharge manifolds.
Pic. 1: Disassembling of the manifolds
Disassemble pump chambers. For DH pump series
untighten the screws and bolts, for the DL pump series
release the clamp bands.
Pic. 2: DH pump series
Pic. 3: DL pump series
Afterdisassemblingofthepump chambers,thediaphragms
can be disassembled. First pump side: Disassemble the
outer piston (diaphragm with piston fixture).The piston rod
features a wrench attachment point. Hold it in place with
a wrench (pic. 4 and 5). Remove the assembly consisting
of outer piston, diaphragm and inner piston (piston rod
is exposed). On the opposite side take out the assembly
consisting of the diaphragm, inner piston, outer piston
and piston rod, from the center block (w/o picture). Detach
piston rod from the second diaphragm by clamping in an
exposed side of the piston rod in a bench vise. Disassemble
the outer piston and remove from piston rod. Diaphragm
and inner piston can be disassembled.
Pic. 4: Diaphragm disassembly Pic. 5: Hold it in place with wrench
Pic. 6: Diaphragm with piston fixture
2. Assembling the nopped E4® diaphragms
Screw threaded pin with hex wrench into the nopped E4®
diaphragm.
Pic. 7
Outer piston Inner pistonDiaphragm

3
www.cranecpe.com
Replacing the diaphragms
Place switch disc on top. The radius or the chamfer is
mounted in the direction of the diaphragm´s air side.
(Pic. 8)
Pic. 8
Screw piston rod onto set screw and tighten by hand
(nopped E4® assembly unit including the piston rod, see
Pic. 9)
Pic. 9
Pic. 10
Before assembling the diaphragm unit, check whether
other parts of the center block need to be exchanged
(e.g. defective or dirty seals, piston rod bearings, defect
air valve, pilot rod or silencer). If required, exchange these
accordingly.
Slide in the nopped E4® assembly unit into the center block
(picture 11) and fix the second diaphragm with switch disc
on the opposite side (mount the threaded pin in the second
nopped E4® diaphragm as shown in picture 7). Tighten the
second diaphragm by hand (picture 12). At the same time,
lock the piston rod with a wrench.
Install pump chambers, insert valve seats and balls (check
for any damages and if required replace), mount suction
and discharge manifolds as per the DEPA® IOM.
Pic. 11 Pic. 12: Tighten by hand
The DEPA® nopped E4® starter kit contains
• 2 diaphragms
• 2 switch discs
• 2 set screws
• Sealings for air control area of pump
Note: The DEPA® nopped E4® starter kit includes switch discs
and set screws in the matching sizes. Switch disc material for
sizes 15, 50 and 80 is POM, for the sizes 25 and 40 aluminium.
Each switch disc has a different thickness. The set screws are
available in three sizes (15, 25 & 40 and 50 & 80)
Pic. 13: Switch discs and set screws
Note: For DEPA® pumps with nopped E4® diaphragms a new
pump coding system is used. To recognize a retrofitted DEPA®
pump, please use the sticker enclosed in this manual and
attach it, next to the nameplate area. Upon request we can
supply you with a new nameplate.
Chamfer radius
Aluminium switch disc POM switch disc
15 25 40 50 80

Crane ChemPharma & Energy
Crane Process Flow Technologies GmbH
Heerdter Lohweg 63-71
40549 Düsseldorf, Germany
Phone: [phone]
E-mail: [email protected]om
www.cranecpe.com
www.depapumps.com
Crane Co., and its subsidiaries cannot accept responsibility for possible errors in catalogues, brochures, other printed materials, and website
information. Crane Co. reserves the right to alter its products without prior notice, including products already on order provided that such
alteration can be made without changes being necessary to specifications already agreed. All trademarks in this material are property of
the Crane Co. or its subsidiaries. The Crane and Crane brands logotypes (in alphabetical order), (ALOYCO®, CENTER LINE®, COMPAC-NOZ®,
CRANE®, DEPA® DUO-CHEK®, ELRO®, FLOWSEAL®, JENKINS®, KROMBACH®, NOZ-CHEK®, PACIFICVALVES®, RESISTOFLEX®, REVO®, SAUNDERS®,
STOCKHAM®, TRIANGLE®, UNI-CHEK®, WTA®, and XOMOX®) are registered trademarks of Crane Co. All rights reserved.
brands you trust.
CCPE-DEPA-CSD-IM-EN-A4-2019_02_01
®
®
Connect with DEPA®
linkedin.com/company/crane-depa
@depa_pumps
[email protected]