1: INPUT: Connect your guitar to this jack by means of a shielded instrument cable.
2: OD LEVEL: Use this control to adjust the volume and intensity of the Overdrive
channel. This control is only active when the OD/Clean switch (#3) is depressed.
3. OD/CLEAN: Use this switch to select the OD channel (switch depressed) or the
Clean channel (switch in the out position). The OD channel gives you sounds rang-
ing from crunchy rhythm to screaming leads, while the Clean channel gives you
sounds from sparkling clean to slightly crunchy.
4: CLEAN LEVEL: Use this control to adjust the volume of the Clean channel. This
control is only active when the OD/Clean switch (#3) is in the out position.
5: HIGH: Use this control to adjust the output level of the high frequencies. Rotating
this control counter clockwise reduces the high frequency output; rotating it clock-
wise increases it.
6: LOW: Use this control to adjust the output level of the low frequencies. Rotating
this control counter clockwise reduces the low frequency output; rotating it clock-
wise increases it.
7. REV LEVEL: Use this control to adjust the amount of reverberation added to the
signal. With the control in the fully counter clockwise position the signal is “dry” (no
reverb). As you rotate the control clockwise the amount of reverb increases.
8. CD INPUT: Use these RCA jacks to connect an external source (such as a CD
player, tape player or rhythm machine) to the amplifier. The signal at these jacks is
summed into a mono signal which is sent to the internal power amp circuit. Use the
external source’s output level control to adjust the signal for the proper mix with
your instrument.
9: HEADPHONES: Use this jack to connect a pair of stereo headphones for private
listening. The external speaker is disconnected when headphones are in use.
10: POWER LED: This LED illuminates when power is applied to the amplifier.
11: POWER SWITCH: Use this switch to turn the amplifier on (top of the switch
depressed) and off (bottom of the switch depressed).
12: AC LINE IN: (Rear panel, not shown) The grounded power cord should only
be plugged into a grounded power outlet that meets all applicable electrical codes
and is compatible with the voltage, power, and frequency requirements stated on
the rear panel. Do not attempt to defeat the safety ground connection.
Congratulations and thank you for choosing the Crate TG10R GuitarAmplifier.
This rugged amplifier provides you with serious clean and distorted sounds and fea-
tures two bands of equalization, reverb, CD Input jacks, and a jack for headphones.
In order to get the most out of your new amplifier, we strongly urge you to read this
user’s guide before you begin playing.
IMPORTANT SAFETY INSTRUCTIONS
•READ, FOLLOW, HEED, AND KEEPALL INSTRUCTIONS AND WARNINGS.
•DO NOT OPERATE NEAR ANY HEAT SOURCE AND DO NOT BLOCK ANY VENTILATION OPENINGS ON THIS APPARATUS. FOR
PROPER OPERATION, THIS UNIT REQUIRES 3” (75mm) OF WELL VENTILATED SPACEAROUND HEATSINKS AND OTHERAIR
FLOW PROVISIONS IN THE CABINET.
•DO NOT USE THIS APPARATUS NEAR SPLASHING, FALLING, SPRAYING, OR STANDING LIQUIDS.
•CLEAN ONLY WITH LINT-FREE DAMP CLOTHAND DO NOT USE CLEANINGAGENTS.
•ONLY CONNECT POWER CORD TO A POLARIZED, SAFETY GROUNDED OUTLET WIRED TO CURRENT ELECTRICAL CODES AND
COMPATIBLE WITH VOLTAGE, POWER,AND FREQUENCY REQUIREMENTS STATED ON THE REAR PANEL OF THEAPPARATUS.
•PROTECT THE POWER CORD FROM DAMAGE DUE TO BEING WALKED ON, PINCHED, OR STRAINED.
•UNPLUG THE APPARATUS DURING LIGHTNING STORMS OR WHEN UNUSED FOR LONG PERIODS OF TIME.
•ONLY USE ATTACHMENTS,ACCESSORIES, STANDS, OR BRACKETS SPECIFIED BY THE MANUFACTURER FOR
SAFE OPERATION AND TOAVOID INJURY.
•WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK OR FIRE, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
•SERVICE MUST BE PERFORMED BY QUALIFIED PERSONNEL.
•OUR AMPLIFIERS ARE CAPABLE OF PRODUCING HIGH SOUND PRESSURE LEVELS. CONTINUED EXPOSURE TO HIGH SOUND
PRESSURE LEVELS CAN CAUSE PERMANENT HEARING IMPAIRMENT OR LOSS. USER CAUTION IS ADVISEDAND EAR PRO-
TECTION IS RECOMMENDED IF UNIT IS OPERATED AT HIGH VOLUME.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOIS-
TURE. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
"IT IS NECESSARY FOR THE USER TO REFER TO THE INSTRUCTION MANUAL"
“ES NECESARIO QUE EL USUARIO SE REFIERA AL MANUAL DE INSTRUCCIONES.”
"REFERREZ-VOUS AU MANUAL D'UTILISATION"
EXPLANATION OF GRAPHICAL SYMBOLS:
EXPLICACION DE SIMBOLOS GRAFICOS:
EXPLICATION DES SYMBÔLES GRAPHIQUES:
"DANGEROUS VOLTAGE"
“VOLTAJE PELIGROSO”
"DANGER HAUTE TENSION"
==
PRECAUCION
RIESGO DE CORRIENTAZO
NO ABRA
PRECAUCION: PARA REDUCIR EL RIESGO DE INCENDIOS O DESCARGAS
ELECTRICAS, NO PERMITA QUE ESTE APARATO QUEDE EXPUESTO A LA
LLUVIA O LA HUMEDAD. PARA DISMINUOIR EL RIESGO DE CORRIENTAZO.
NO ABRA LA CUBIERTA. NO HAY PIEZAS ADENTRO QUE EL USARIO PUEDO
REPARAR DEJE TODO MANTENIMIENTO A LOS TECHNICOS CALIFICADOS.
ATTENTION
RISQUE D'ELECTROCUTION
NE PAS OUVRIR
ATTENTION: PROTÉGEZ CET APPAREIL DE LA PLUIE ET DE L'HUMIDITÉ
AFIN D'ÉVITER TOUT RISQUE D'INCENDIE OU D'ÉLECTROCUTION. POUR
REDUIRE D'ELECTROCUTION NE PAS ENLEVER LE COUVERCLE. AUCUNE
PIECE INTERNE N'EST REPRABLE PAR L'UTILISATEUR. POUR TOUTE
REPARATION, S'ADRESSER A UN TECHNICIEN QUALIFIE.
