CrazyFly Hexa Binding User manual

USER MANUAL
© CrazyFly Kiteboarding 2015.
WWW.CRAZYFLYKITES.COM
kiteboardingforchildren.com crazyflykites.com/register
REGISTER
YOUR GEAR
crazyflykites.com/extend
YEARS EXTENDED
WARRANTY
2

2. 3.
PACKAGE CONTENTS OPTIONAL PACKAGE CONTENT
IF BOUGHT TOGETHER WITH A CRAZYFLY KITEBOARD
1 x Hexa bag
1 x Manual
4 x Quattro Stix Long
4 x Quattro Stix Short
4 x Screw M6 x 20
4 x Hexa washer
1 x Hexa footstrap Left – L
1 x Hexa footstrap Right – R
1 x Hexa footpad Left – L
1 x Hexa footpad Right – R
4 x Razor fin
8 x Razor fin screw 4.5 x 16
2 x Handle screw M6 x 10
1 x Handle

4. 5.
1. Take 1 pc Quattro Stix Short and 1 pc Hexa footpad Right. Place the
Quattro Stix Short in the front position of the Hexa footpad frame on
the left and on the right side.
3. Adjust all Quattro Stix to the desired position. Make sure there is
one empty position between Quatrro Stix Short and Quattro Stix Long.
4. Place the Hexa footpad Right on the board and select desired insert
position. This determines your stance width.
2. Take 1 pc Quattro Stix Long and continue on the Hexa footpad Right.
Place the Quattro Stix Long in the back position of the Hexa footpad
frame on the left and on the right side.
HOW TO MOUNT

6. 7.
5. Put 2 pcs Hexa washers in place, one to the left and the other one to
the right side of the Hexa footpad. Make sure the holes in the washer are
aligned with the inserts on the board. Tighten 2 pcs screws slightly - left
and right side of the Hexa footpad.
6. Adjust the Hexa footpad angle to the desired position.
7. Fully tighten the screws. Please check the footpad screws after the
first few rides, as they may come loose. If loose, make sure to fully
tighten the screws.

8. 9.
8. Take the Hexa footstrap Right and open the velcro. Thread the velcro
through the Quattro Stix. It is best to start on the Quattro Stix Long in the
left side of the Hexa footpad right (inside of the foot). Then continue with
threading the velcro through the Quattro Stix Short on the same side.
10. Thread the Velcro through the Quattro Stix on the right side (outside
of the foot) on the Hexa footpad Right.
9. Slide the Quattro Stix inside the footstrap. Slightly tighten and close
the threaded velcros. Leave the velcros a bit loose and close the top
velcro. Leaving the velcro loose will make threading the velcro on the
other side of the footpad easier.
11. Slide the Quattro Stix inside the footstrap.
Tighten and close the velcro.

10. 11.
12. Step inside the Hexa Binding.
13. Adjust the Hexa footstrap with the velcros for the best fit.
14. If further adjustments for the angle of the binding is needed, loosen
the screws a little until the Hexa Binding is able to spin. Adjust the angle
again to the desired position and fully tighten the screws.
16. Enjoy the ride
15. If further adjustments for the footstrap position and footpad
position are needed, undo the screws completely. Lift up the Hexa
Binding, push the Quttro Stix down so they pop out of the Fusion Frame.
Adjust the Quattro Stix to the desired position and pop them back in the
Fusion Frame. Mount the Hexa Binding back on the board to the
desired position and fully tighten your screws.

USER MANUAL
© CrazyFly Kiteboarding 2015.
WWW.CRAZYFLYKITES.COM
kiteboardingforchildren.com crazyflykites.com/register
REGISTER
YOUR GEAR
crazyflykites.com/extend
YEARS EXTENDED
WARRANTY
2