Creative Play ALLOTMENT Digging Planter User manual

ALLOTMENT
Digging Planter
Assembly Instructions
REF: CP068/DPA - ALLOTMENT DIGGING PLANTER
pg 1 of 12

REF: CP068/DPA - ALLOTMENT DIGGING PLANTER
pg 2 of 12
PARTS required
x8 (angle cleats/brackets)
x20 (80mm brass screws)
x38 (40mm brass screws)
x44 (120mm brass screws)
QTY 6 (147mm x 47mm)
QTY 2 (147mm x 47mm)
QTY 4 (47mm x 47mm)
QTY 2 (47mm x 47mm)
QTY 4 (90mm x 90mm)
QTY 2 (Hex board base)
T1
T1A
T2
T3
T4
H1

REF: CP068/DPA - ALLOTMENT DIGGING PLANTER
pg 3 of 12
PARTS required
TOOLS required
QTY 2 DIVIDER ASSEMBLIES
(consists of T5 / T6 timbers and 4 angle cleats)
T5
T6

REF: CP068/DPA - ALLOTMENT DIGGING PLANTER
SOIL
TIMBER SUPPORT POST
CONCRETE
pg 4 of 12
Foundation Details

Digging Planter to be pre-assembled UP TO STEP
Installation on site jump to this step
Assembly the first RING
Using 4 x T1 timbers
REF: CP068/DPA - ALLOTMENT DIGGING PLANTER
pg 5 of 12
Assembly Instructions
18
2
T1 T1A
T1
T1
T1
T1
T2
T2
T2
T3
T3
T4
T4
T4
T4
T1A
T1
Dividers shown in BLACK above

REF: CP068/DPA - ALLOTMENT DIGGING PLANTER
pg 6 of 12
Assembly Instructions
3
4
Assemble the second ring
Using the remaining T1 timbers & T1A timbers
The 2 ring are to be positioned as shown below
T1
T1
T1A
T1A

One side will be butted up
against the adjacent T1 timber
REF: CP068/DPA - ALLOTMENT DIGGING PLANTER
pg 7 of 12
Assembly Instructions
5
6
Screw T2 timbers (floor support) to the lower T1 ring
Using 80mm brass screws (5 per T2 timber)
Attach the remaining T2 timbers
Using 80mm brass screws
T1
T2
T2 T2

REF: CP068/DPA - ALLOTMENT DIGGING PLANTER
pg 8 of 12
Assembly Instructions
7Screw T3 timbers to the T2 timbers & T1 lower ring
Using 40mm / 120mm brass screws & angle cleats (use 40mm brass screws to attach angle cleats to T3 timbers
T3
T3

REF: CP068/DPA - ALLOTMENT DIGGING PLANTER
pg 9 of 12
Assembly Instructions
8
9
Screw H1 (floor section) to the T2 timbers
Using 11 x 40mm brass screws
Attach the Assembly with floor & upper ring to the T4
timbers
Using 120mm brass screws
...Repeat for the second floor section
Be careful that screws do
not ‘cross’ screws used for
the T2 support timbers

REF: CP064/BSP - BASIC SANDPIT REF: CP068/DPA - ALLOTMENT DIGGING PLANTER
pg 10 of 12
Assembly Instructions
10 Screw the T1 ‘rings to the T4 timbers as shown
SCREWING INTO FLAT FACE
OF T4 timbers
- use 4 x 120mm brass screws
- Screw in the centre as shown
SCREWING INTO GROOVED FACE
OF T4 timbers
- use 4 x 120mm brass screws
- Offset screws as shown
dashed line shows screws
going into the flat side
(screws into grooved side
sit ‘inside)

REF: CP068/DPA - ALLOTMENT DIGGING PLANTER
pg 11 of 12
Assembly Instructions
11
12
Main assembly complete
Attach the divider
Using 40mm brass screws for angle cleats & 120mm
brass screws for T5 to T1A timber
T5 T1A
T6

REF: CP068/DPA - ALLOTMENT DIGGING PLANTER
pg 12 of 12
Assembly Instructions
13 Repeat for the second divider