Creative Playthings Lexington Premium Pack 15 User manual

LEXINGTON PREMIUM PACK 15
LEXI9WPP15-100 Rev A (04-18)
© Copyright 2018, Creative Playthings
CHILDHOOD STARTS HERE
LEXI9WPP15
L P P 
• Start by assembling the Lexington tower. Instructions and hard-
ware are in the cartons noted at left. The gym is rotated 90° from
the position shown in the instructions.
The components of this gym can be combined with
others to create different play sets. This is the best
order of assembly to create this specic set.
Read this sheet and all instructions included with the
different parts before assembly.
See the Instructions and Owner's Manual included in
carton 63007-445 for important safety information.
Dimensions of assembled package:
24' 0" wide x 13' 7" deep x 11' 6" tall
Cartons for this Play Set:
1 63007-421 Lexington Gym 1 (Hardware)
1 63007-422 Lexington Gym 2
1 63007-423 Lexington Gym 3
1 63007-445 Lexington Roof (Hdwre & Instr)
1 SH946-102 Access Ladder, 5ft
1 AG942-400 Access Ladder Handles (Hdwre & Instr)
1 63058-202 4 Position Swing Beam
1 63060-222 9ft Swing Beam Legs (Hdwre & Instr)
1 50546-777 3 Swings, 1 Trapeze
1 15166-400 10 ft. Super Wave Slide
1 SM964-402 Gable Fans (Hdwre & Instr)
1 SM963-402 Dormer (Hdwre & Instr)
1 63073-101 Clubhouse Window Pk (Hdwre & Instr)
2 40456-402 End Panel
1 40459-402 Double Window Panel
1 40460-402 Door & Window Panel (Hardware)
1 SC910-800Q Lexington Play Floor (Hdwre & Instr)
1 63091-111 Direct Connect Adapter (Hdwre & Instr)
1 8400-202 Spiral Slide, Green (Hardware)
1 AA917-603 Fireman's Pole (Hdwre & Instr)
1 AG943-400 Slide Handle (Hdwre & Instr)
15 1/2"
7 1/4"
3"
0"
• Wait to install the Access Ladder, Slide, and
Wall Slats until after the rest of the play set is
complete.
• Lex step 7. Do not install the safety rail.
• Lex step 8. Do not install the angle braces.
They conict with the clubhouse panels.
• Lex step 14. Do not install the end wall support
on the spiral slide end of the tower. The direct
connect adapter will take the place.
• Lex step 15. The swing mount isn't needed.
• Lex step 25. Before installing the roof, nd the
post where the swing beam will mount. Drill
7/16" diameter holes through the post at 3",
7-1/4" and 15-1/2" below the top of the post as
shown at right.The beam will be mounted to the
front of the post using these holes. Insert one
5/16" weld nut into the top hole on the inside
face of the post. Be sure the threads on the
weld nut are clear, it will be captured by the roof
support. Install the roof.
Dormer
• Mount the Swing Beam using instructions and hardware included
in 63060-222. Mount the beam to the previously drilled holes at
right rather than the way shown in the instructions. You may need
to temporarily disconnect the roof from the post to put the beam in
place.

© Copyright 2018, Creative Playthings
LEXINGTON PREMIUM PACK 15
LEXI9WPP15-100 Rev A (04-18) Page 2
• Install the Play Floor (SC910-800Q).
• Install the Clubhouse Panels arranged as shown in the im-
ages in this guide. Instructions and hardware are attached
to the door panel (40460-402).
• Install the Direct Connect Adapter (63091-111) and the
Spiral Slide (8400-202) to the end opposite the swings.
• Install the Gable Fans (SM964-402).
• Using a ladder, install the Dormer (SM963-402) in the po-
sition shown. Ladder access may be obstructed by later
installations.
• Install the shutters and ower box from the Clubhouse
Window Pack (63073-101) in the position shown above.
• Install the Fireman's Pole to the front post nearest the spi-
ral slide as shown on the rst page of this guide.
• Set the Access Ladder and Slide as shown on the rst
page of this guide. Check spacing.
• Secure the access ladder using the method shown in step
17 of the Lexington instructions.
• Fasten the Access Ladder Handles (AG942-400) to the
Access Ladder.
• Install the slide mount and slide using the method shown
in steps 23 and 24 of the Lexington instructions.
• Install wall slats in the postions shown in images, using the
methods from the Lexington Instructions. Gaps must be
narrower than 3-1/2" or wider than 9" to prevent potential
head entrapment.
• Mount the hand grips to the entrance wall slats.
• Mount the Slide Handle (AG943-400) above the slide.
• Double-check all fasteners are secure and all recessed
hardware is covered by hole caps.
Swing Beam
Spiral Slide
Gable Fan
Window Pack
Clubhouse