Creative Playthings Playtime PS18EAS User manual

MODEL PS18EAS
ASSEMBLY MANUAL
If you have problems or questions about your Creative Playthings play set,
DO NOT CALL THE RETAILER.
Contact Creative Playthings Customer Service at 1-800-598-4997 or
[email protected]
Please read the owner’s manual before the
assembly of your Play Set. it provides additional
information on the care and use of your Play Set.
You must carefully read the entire instruction man-
ual before proceeding with the assembly or use
of your new Play Set.
Creative Playthings takes great care to design its
products with your child’s safety in mind. How-
ever, only with careful supervision and proper
safety instructions, can you be assured of safe
play time on any product designed for children.
Save these instructions for reference in case you
need to contact customer service.
By
This product is intended for single
family home/residential use only and
not intended for use in any public
setting. Placement in any public
setting constitutes a misuse of this
product.
All hardware on this set is specially coated
for corrosion resistance.
If non-Creative Playthings hardware is used,
it must be galvanized or stainless steel.
™

© Copyright 2014, Creative Playthings
MODEL PS18EAS
19862-700 Rev A (07-20) Page 2
PLAY SET SAFETY
Observing the following statements & warnings reduces the likelihood of serious or fatal injury:
• Children should use equipment only in its intended manner.
• Children should not wear loose or stringed clothing while using playground equipment.
• Children should not play on equipment in wet weather conditions due to potentially slippery surfaces.
• Children should NOT walk too closely in front of, behind, or between moving swings and trapezes.
• Children should NOT swing empty swing seats.
• Children should NOT jump off swings and/or trapeze while they are in motion.
• Children should NOT twist swing chains because this will reduce the strength of the chains.
• Children should sit in the center of the swings with their full weight on the seats.
• Children should NOT be on the top surface of the swing beam.
• Children should NOT use the equipment in a manner other than intended.
• Children should NOT get off the equipment while it is in motion.
• On-site adult supervision is required at all times for children of all ages.
• Until assembly is complete, DO NOT let your children use the Play Set.
• Never fasten anything not approved by Creative Playthings to your Play Set. Accessories or items not ap-
proved by Creative Playthings include; Dog runs, clothes lines, electrical devices, or bird feeders etc.
• Suspended ropes, chains, and cables must be secured at both ends.
• Suspended ropes, chains, and cables must not be capable of looping back on themselves.
• Do not allow more than 120 lbs. on Single occupancy swing accessories such as the Sling Swing and Trapeze.
• Do NOT allow more than 175 lbs. on multiple use swing accessories such as the Back-to-Back Plastic Glider.
• Do NOT allow more children on the Play Set than can simultaneously use all the swing stations at one time.
• Children MUST NEVER wear bicycle helmets while playing on the play-set.
Assembly Safety:
• Adult assembly required
• Face slide away from the sun.
• Keep the work area clean and clear of obstructions.
• Children should stay out of the work area until the safe play area is cleared of obstacles, the Play Set has been
completely assembled, all hardware has been tightened and checked, and all tools have been picked up.
• Keep children off the Play Set until it has been completely assembled.
• Parts of the assembly process may require help from another competent adult.
• Do not stand on the platform until the Play Set has been completely assembled, use a step ladder if you can
not reach high enough.
• Follow the manufacturers' safety recommendations for the tools and equipment you use.
• Avoid assembling your Play Set in poor weather conditions.
• Wear proper clothing and safety equipment (safety glasses, boots, and gloves) while assembling your Play Set.
FOR SAFETY SAKE, PLEASE TAKE TIME TO READ ALL INSTRUCTIONS COMPLETELY AND
CAUTION YOUR CHILDREN APPROPRIATELY.

MODEL PS18EAS
19862-700 Rev A (07-20)
© Copyright 2014, Creative Playthings Page 3
SAFE PLAY AREA
SELECTING THE CORRECT LOCATION FOR YOUR PLAY PRODUCT IS IMPORTANT FOR
YOUR CHILDREN’S SAFETY AND THE PRODUCT’S LONGEVITY.
Play Set Dimensions:
• The MODEL PS18EAS Play Set has ground dimensions of 14'-10" x 12'-4".
• The MODEL PS18EAS Play Set requires a level ground surface of 26'-10" x 29'-0" for a Safe Play Area.
• Additional accessories may increase the size of the Safe Play Area.
• The maximum fall height for your MODEL PS18EAS is 87" as measured from the top of the swing beam.
Safe Play Area:
• The Safe Play Area refers to a zone extending 6' (2 meters) beyond the Play Set on all sides, including the slide
and the space above the Play Set. Because children may deliberately jump from a moving swing, the Safe Play
Area must be extended to 14' (4.27 meters) in front of and behind a swinging Accessory.
• The ground surface must be level. Installing your Play Set on sloping ground can cause it to lean or “rack”.
This leaning puts additional stress on all connections and joints and in time will cause those connections to
loosen and fail.
• The Safe Play Area must be free of all structures, landscaping, trees and branches, rocks, wires, and other
obstacles to safe play. Children can be seriously injured running, or swinging into these obstacles.
• Remove all tripping hazards from the Safe Play Area. Tripping hazards include; roots, stumps, rocks, landscap-
ing, sprinkler heads, railroad ties, plumbing and electrical connections.
• Do not install your Play Set over concrete, gravel, asphalt, packed earth, or any other hard surface. The follow-
ing is a list of recommended ground covers from the Consumer Product Safety Commission.
RECOMMENDED GROUND COVER
Suggested Material Uncompressed Depth
Double Shredded Bark Mulch 9"
Uniform Wood Chips 12"
Fine Gravel 12"
Fine Sand 12"
• Any edging used to contain the ground cover must be beyond the Safe Play Area. (i.e. Landscape Timbers)
A FALL ONTO A HARD SURFACE COULD RESULT IN SERIOUS
INJURY.
Safe play area using
recommended ground cover.
Whichever is greater
Landscape Timbers 6' from
play structure.
6'
(2 M)
6'
(2 M)
6'
(2 M)
6'
(2 M)
14'
(4.27 M)
14'
(4.27 M)

© Copyright 2014, Creative Playthings
MODEL PS18EAS
19862-700 Rev A (07-20) Page 4
HARDWARE BAG CONTENTS
50568-701 PT Hardware
89 17001-104 Weld Nut 1/4"
12 12002-203 Flat Washer 8MM
112 12002-205 Flat Washer 1/4"
85 12017-205 Lock Washer 1/4"
8 17120-502 Self-Drill Screw #10 x 1-1/2"
8 17003-409 Hex Bolt 1/4 x 1"
16 17003-609 Hex Bolt 1/4 x 1-1/2"
15 17003-809 Hex Bolt 1/4 x 2"
12 17003-1209 Hex Bolt 1/4 x 3"
18 17003-1409 Hex Bolt 1/4 x 3-1/2"
12 17003-1609 Hex Bolt 1/4 x 4"
4 17003-1809 Hex Bolt 1/4 x 4-1/2"
ASSEMBLY HARDWARE:
More hardware is included than is required for assembly.
1/4 x 1" Hex Bolt
1/4 x 1" Truss Head Bolt
1/4 x 1-1/2" Hex Bolt
1/4 x 2-1/2" Hex Bolt
1/4 x 3-1/2" Hex Bolt
1/4 x 4-1/2" Hex Bolt
1/4 x 2" Hex Bolt
1/4 x 3" Hex Bolt
1/4 x 4" Hex Bolt
Illustrations are representative of hardware.
Slight variation of appearance may occur.
1/4" Flat Washer 8mm Flat
Washer
#10 x 1-1/2" Self-Drill Screw
#8 x 1-1/4" Screw
#10 x 1-5/8" Screw
#10 x 2-1/2" Screw
#10 x 2" Screw
1/4 x 1-1/2" Lag Screw
1/4 x 2" Lag Screw
1/4 x 3" Lag Screw
1/4 x 3-1/2" Lag Screw
1/4" Lock
Washer
Access. Bracket
(Not to Scale)
1/4" Weld
Nut
3 17119-409 Truss Head Bolt 1/4 x 1"
2 17036-601 Lag Screw 1/4 x 1-1/2"
31 17036-801 Lag Screw 1/4 x 2"
6 17036-1201 Lag Screw 1/4 x 3"
2 17036-1401 Lag Screw 1/4 x 3-1/2"
4 14161-400 Access Bracket, Green
50568-702 PT Screws
60 17025-104 Screw #8 x 1-1/4"
126 17020-115 Screw #10 x 1-5/8"
44 17020-107 Screw #10 x 2"
4 17020-113 Screw #10 x 2-1/2"

MODEL PS18EAS
19862-700 Rev A (07-20)
© Copyright 2014, Creative Playthings Page 5
PRE ASSEMBLY INFORMATION
CREATIVE PLAYTHINGS PLAY SETS USE A FEW STANDARD CONNECTIONS.
BECOMING FAMILIAR WITH THESE CONNECTIONS WILL SIMPLIFY ASSEMBLY AND
INSURE A SAFER PLAY PRODUCT FOR YOUR CHILDREN.
Hex Bolt & Weld Nut Assembly Procedure:
Assembly Layout:
Align the holes in the parts to be fastened. Start
preliminary tightening of bolt into weld nut by
hand. Tighten each bolt with a wrench until the
lock washer is fully compressed between the
head of the bolt and the at washer.
Correct Assembly:
Bolt has been screwed securely into weld nut
and the connection is tight. Check connec-
tions periodically for tightness during the life
of the Play Set . Do not over tighten.
Incorrect Assembly:
If during assembly or maintenance the bolt pro-
trudes 1/8" past the weld nut, use additional at
washers, call customer service or replace the
bolt at a local hardware store. You may be over-
tightening or using the wrong size bolt.
Failure to replace this bolt with a shorter one
could result in serious injury.
Typical Installation - Lag Screws:
• Pilot drill with the appropriate
diameter drill bit and then use
a socket to tighten.
• DO NOT over tighten
Typical Installation - Wood Screws:
• Use an electric drill or screw gun to drive screws.
• Drill 1/8" pilot holes where required.
• We recommend that you lubricate the
threads of the screws with beeswax or
soap to ease installation and minimize
breaking screws.
• It is very important to make cer-
tain that the tops of all screws are
ush with the surface of the wood
and there are no protruding sharp
edges.
Lag Screw
Flat Washer
Hex Bolt
Lock Washer
Flat Washer
Weld Nut

© Copyright 2014, Creative Playthings
MODEL PS18EAS
19862-700 Rev A (07-20) Page 6
PLAY SET VIEW
AA
K
AG
M
C
AJ
F
AE
AO
AP
AN
B
V
AD
W
E
X
Y
I
Z
AL
O
J
R
AT
S
AF
AB
AC
AH
A
AR
AM
AK
L
N
P
Q
G
60081-102 Playtime Swing Beam
AA934-204 2 Swings, 1 Trapeze*
(2 Sling Swings & 1 Ring Trapeze)
8515-202 8 Ft. Wave Slide, Green
Items Packaged Separately:
*Alternative swing features may
be included with your set. Use the
instructions packed with the swing
equipment for assembly.

MODEL PS18EAS
19862-700 Rev A (07-20)
© Copyright 2014, Creative Playthings Page 7
COMPONENT VIEW
X 9 33953-102 Deck Board 5/4 x 6 x 41-1/2"
Y 3 33954-102 Narrow Deck Board 5/4 x 4 x 38-5/8"
Z 2 33956-102 End Joist 5/4 x 6 x 22"
AA 1 33972-102 Ladder Slat 1 x 4 x 15-3/4"
AB 1 35664-102 Lower Wall Supp. 5/4 x 4 x 59-1/2"
AC 1 35665-102 Short Wall Supp. 5/4 x 4 x 23-1/4"
AD 12 33745-402 Roof Board 1 x 6 x 39-1/2"
AE 4 14202-400 1" Dia. X 15" Rung, Green
AF 2 32526-102 Climber Upright 2 x 3 x 52-3/4"
AG 12 33741-102 Short Wall Slat 1 x 4 x 19-1/2"
AH 5 33920-102 Rock Board 5/4 x 6 x 27"
AI* 2 33923-102 Swing Mount 2 x 3 x 34"
AJ 1 33924-102 Safety Rail 2 x 3 x 59-3/8"
AK 6 33962-102 Narrow Wall Slat 1 x 4 x 24-1/2"
AL 2 33963-102 Entrance Slat 5/4 x 6 x 24-1/2"
AM 1 35440-102 Rock & Rope Board 5/4 x 6 x 27"
AN 5 35449-102 Spacer Board 5/4 x 4 x 27"
AO 3 15034-100 Hand Grips
AP 1 18008-138 Climbing Rope
AQ* 5 36515-102 Ground Stake
AR 1 50428-400 Climbing Rocks (6)
AS 1 50469-100 Small CP Name Plate Pack
AT 1 8515-202 8 Ft. Wave Slide, Green
A 4 32561-102 Angle Brace 2 x 3 x 17-1/4"
B 2 35663-102 Mid Post 2 x 4 x 32-1/2"
C 1 33760-102 Platform Right 2 x 4 x 59-3/8"
D* 1 33761-102 Platform Left 2 x 4 x 59-3/8"
E 2 33949-102 Sandbox End 5/4 x 6 x 41-1/4"
F 2 33950-102 Sandbox Side 5/4 x 6 x 59-1/2"
G 1 33951-102 Platform Front 5/4 x 6 x 41-1/2"
H* 1 33952-102 Platform Back 5/4 x 6 x 41-1/2"
I 1 33955-102 End Support 5/4 x 6 x 41-1/2"
J 1 33968-102 Front Arch 5/4 x 6 x 41-1/2"
K 1 35441-102 Left Wall Support 5/4 x 6 x 59-1/2"
L 1 35442-102 Right Top Support 5/4 x 6 x 59-1/2"
M 4 35443-102 Roof Upright 2 x 4 x 20-3/4"
N 1 40653-102 Post, Back Left
O 1 40654-102 Post, Back Right
P 1 40655-102 Post, Front Left
Q 1 40656-102 Post, Front Right
1 50568-701 PT Hardware Bag
1 50568-702 PT Screw Bag
1 50540-304 Instruction Pack, Eastport
R 1 33702-102 Ladder Rail Left 2 x 3 x 47-1/2"
S 1 33703-102 Ladder Rail Right 2 x 3 x 47-1/2"
T* 1 33732-102 Stringer 2 x 3 x 59-1/2"
U* 1 33742-102 Ceiling Joist 1 x 4 x 14-5/8"
V 6 33744-102 Rafter 2 x 3 x 31"
W 1 33922-102 Rock Wall Mount 5/4 x 6 x 39-1/2"
Take inventory of all parts, making sure nothing is missing or defec-
tive. If you nd that parts are missing or defective call the Creative
Playthings Customer Service Department at 1-800-598-4997.
BOX 2 (CONT'D)
BOX 2 - 60083-342
BOX 3 - 60083-343
* Not marked on Play Set View page.
BOX 1 - 60083-341

© Copyright 2014, Creative Playthings
MODEL PS18EAS
19862-700 Rev A (07-20) Page 8
MAINTENANCE INSTRUCTIONS
YOUR CREATIVE PLAYTHINGS PLAY SET IS STAINED AT OUR FACTORY.
STAINING IS NOT NEEDED AT THE TIME OF INITIAL ASSEMBLY.
Re-staining Information:
• Pigmented, exterior, water repellent stains are recommended and will provide an excellent barrier against moisture
without hiding the natural wood grain or leaving a lm that may later crack or peel.
• We recommend that you apply stain according to the instructions and precautions recommended by the stain manufacturer.
• It should take three or more quarts to cover your set.
• Contact your local dealer or call Creative Playthings for our staining products.
• All rungs are pre-nished at the factory and do not require any nishing at the time of initial assembly.
• Do not paint, or varnish rungs or steps.
• Avoid using nishes that create slippery surfaces.
Maintenance:
• Wooden playground equipment will last for years with proper maintenance. Maintenance of the Play Set nish will vary
depending on weather and climate.
• As a safety precaution, check all hardware, such as nuts and bolts, for tightness twice a month during use and at the
beginning of each play season. Tighten as required and specied in these instructions. Do not over-tighten.
• Check structure twice monthly during usage for any evidence of deterioration. If upon inspection, hardware has sharp edges,
rusted or structural pieces have signs of premature failure; replace them through Creative Playthings Customer Service.
• Oil all metallic moving parts monthly during the usage season.
• The swings, trapeze, tent, rope ladders, and any other removable plastic accessories should be removed and taken
indoors when outside temperatures drop below 32° F (0° C).
• Wood will expand and contract as it adjusts to temperature changes and varying moisture conditions. Checks or cracks
are a natural characteristic of all wood and will not affect the strength or durability of the wooden components.
• To maintain the nish of your set, a light sanding and an application of an exterior stain will repair scratches and prevent
wood from aging prematurely.
• Finishes applied to ladder rungs must not create a slippery surface. Never varnish.
• The wood parts of your Play Set should never be disposed of by burning.
• Dispose of all parts so as not to create a hazard.
• "Check all coverings for bolts and sharp edges and replace when required."
• "Check swing seats, chains, ropes, and other means of of attachments for evidence of deterioration". Replace through
Creative Playthings Customer Service.
• Twice a month during play season rake and check depth of loose ll protective surfacing materials to prevent compac-
tion and to maintain appropriate depth. Replace as necessary.
Tools & Materials Suggested for Finishing & Assembly:
• Claw Hammer
• Carpenter’s Level
• Box Wrench or Sockets (7/16" & 1/2")
• Electric Drill
• 1/8", 3/16", 5/16" diameter Drill Bits
• Screwdriver or driver drill (Medium Phillips)
• Locking Pliers
• 10 ft. Tape Measure
• Framing Square
• 6 ft. Step Ladder

MODEL PS18EAS
19862-700 Rev A (07-20)
© Copyright 2014, Creative Playthings Page 9
ASSEMBLY INSTRUCTIONS
STEP 1 — Assemble Posts:
Locate Back Left Post (N), Back Right Post (O), Front Left
Post (P), and Front Right Post (Q).
Secure each post using two 1/4 x 3" Hex Bolt Assemblies
through the three central holes as shown at left. If the tip of
a Hex Bolt protrudes, add a second Flat Washer next to the
rst.
N
PO
Q
1) These holes are
higher on back posts.
3) These holes face
opposite on the left
& right front posts
Note orientation
of holes
2) No holes here
on Back Right Post
Hint: The posts can be difcult to tell apart. There are three
clues at left.
1) The holes for the Platform Ends are higher on the back
Posts.
2) There are no holes for a Lower Wall Support on the Back
Right Post.
3) Look at the holes on the narrow edge of the post to tell the
Left Front Post from the Right Front Post.
STEP 2 — Front of Tower:
Fasten one Sandbox End (E) to the front of the Front Left
Post (P) and Front Right Post (Q) as shown. Use 1/4 x 4"
Hex Bolt Assemblies in the top holes and 1/4" x 2" Lag
Screws with 1/4" Flat Washers in the bottom holes.
Repeat the process with the Platform Front (G) and Front
Arch (J). Align the hole at the center of the Platform Front
closer to the upper end of the tower.
Front of
tower
The posts are shown in the positions
they will be in the nal assembly.
The parts required to start assembly are in box 1, subse-
quent parts are in box 2 and box 3.
Hex Bolt Assembly:
Throughout this guide a Hex Bolt Assembly consists of one Hex
Bolt, one Lock Washer, one Flat Washer and one Weld Nut.
1/4 x 4" Hex Bolts in
top holes, 1/4 x 2" Lag
Screws in bottom holes.
P
E
G
J
Q

© Copyright 2014, Creative Playthings
MODEL PS18EAS
19862-700 Rev A (07-20) Page 10
ASSEMBLY INSTRUCTIONS
STEP 4 — Left Sandbox Side:
Arrange the back tower assembly and front tower assembly
next to each other on edge as shown at right.
Fasten one Sandbox Side (F) to the Front Left and Back Left
Posts as shown at right. Use 1/4 x 3-1/2" Hex Bolt Assemblies
in the top holes and 1/4" x 2" Lag Screws with 1/4" Flat
Washers in the bottom holes.
STEP 5 — Left Platform Side:
Fasten the Platform Left (D) to the Back Left Post and Front
Left Post in the orientation shown using 1/4 x 3" Hex Bolt As-
semblies. Note the hole positions along the board.
O
E
H
I
N
1/4 x 4" Hex Bolts in
top holes, 1/4 x 2" Lag
Screws in bottom holes.
P
Q
STEP 3 — Back of Tower:
Fasten one Sandbox End (E) to the front of the Back Left
Post (N) and Back Right Post (O) as shown. Use 1/4 x 4"
Hex Bolt Assemblies in the top holes and 1/4" x 2" Lag
Screws with 1/4" Flat Washers in the bottom holes.
Repeat the process with the Platform Back (H) and End
Support (I). Align the hole circled in the illustration closer
to the bottom end of the tower.
O
N
1/4 x 3-1/2" Hex Bolts in
top holes, 1/4 x 2" Lag
Screws in bottom holes.
P
Q
F
Back of
tower
Front of
tower
1/4 x 3" Hex Bolts.
D
N
P
Back of
tower
Front of
tower
Note orientation
of holes

MODEL PS18EAS
19862-700 Rev A (07-20)
© Copyright 2014, Creative Playthings Page 11
ASSEMBLY INSTRUCTIONS
STEP 6 — Raise the Tower:
Lift the top of the tower and walk it up until it stands
vertical on the base.
STEP 7 — Platform and Sandbox Side:
Fasten one Sandbox Side (F) near the base of the
Front Right and Back Right Posts as shown at right.
Use 1/4 x 3-1/2" Hex Bolt Assemblies in the top holes
and 1/4" x 2" Lag Screws with 1/4" Flat Washers in
the bottom holes.
Fasten the Platform Right (C) to the Front Right
Post using one 1/4 x 3" Hex Bolt Assembly. Rest
the other end of the Platform Side on the Back Right
Post with the holes aligned as shown.
STEP 8 — Midposts & Rock Wall Mount:
Align one Midpost (B) as shown at right. Fasten
it to the Platform Left using one 1/4 x 3" Hex Bolt
Assembly.
Fasten the Rock Wall Mount (W) to the Back Right
Post and the Platform Right using one 1/4 x 3-1/2"
Hex Bolt Assembly in the lower right hole.
Fasten the other end of the Rock Wall Mount to the
right Midpost (B) and the Platform Right using one
1/4 x 3-1/2" Hex Bolt Assembly in the lower left hole.
Fasten one 1/4 x 2" Lag Screw and Flat Washer
through the top right hole of the Rock Wall Mount
and into the Back Right Post
Use a level to assure the right Midpost is plumb. Se-
cure using one 1/4 x 2" Lag Screw and Flat Washer.
N
O
1/4 x 3-1/2" Hex Bolts in
top holes, 1/4 x 2" Lag
Screws in bottom holes.
Back of
tower
Front of
tower
F
C
Q
P
1/4 x 3"
Hex Bolt
align
3-1/2" Hex Bolt
Assembly
3" Hex Bolt
Assembly
B
W
2" Lag
Screw
N
P
Q
O
W
Before Step 8, insert 1/4" Weld Nuts into the
two central holes from the back of
the Rock Wall Mount (W).

© Copyright 2014, Creative Playthings
MODEL PS18EAS
19862-700 Rev A (07-20) Page 12
ASSEMBLY INSTRUCTIONS
STEP 9 — Left Wall Support & Roof Uprights:
Orient the Left Wall Support (K) as shown at right. Fasten
the Left Wall Support to the Left Front Post using a 1/4 x 2"
Hex Bolt Assembly though the top hole and a 1/4 x 2" Lag
Screw with Flat Washer in the bottom hole.
Fasten the Left Wall Support to the Back Left Post and one
Roof Upright (M) using two 1/4 x 3-1/2" Hex Bolt Assemblies
as shown.
Fasten the Left Wall Support to the left Midpost and one
Roof Upright (M) using two 1/4 x 3-1/2" Hex Bolt Assemblies
as shown.
STEP 10 — Right Wall Support & Roof Uprights:
Secure the Right Wall Support (L) to the Front Right Post,
then the Back Left Post and Roof Upright (M), then the Mid-
post and Roof Upright (M) as in the previous step.
STEP 11 — Angle Braces:
Ensure the structure is in the place it will be used. Make
any needed ground adjustments before proceeding.
Use a level to determine that all horizontals are level and
posts are plumb. Make sure the tower stands solidly on the
ground.
Fasten two Angle Braces (A) to the Platform Left using two
1/4 x 3" Hex Bolt Assemblies as shown. Fasten the bottom of
the braces to the adjacent posts using 1/4 x 3" Lag Screws
with Flat Washers. Be sure to drill 3/16" diameter pilot
holes in the posts before using the Lag Screws.
Fasten two Angle Braces (A) to the front and back of the
lower platform using two 1/4 x 2" Hex Bolt Assemblies as
shown. Fasten the bottom of the braces to the adjacent
posts using 1/4 x 3" Lag Screws with Flat Washers. Be sure
to drill 3/16" diameter pilot holes before using the Lag
Screws.
K
M
M
M
A
A
A
B
3-1/2" Hex Bolts
2" Hex
Bolt
2" Lag
Screw
M
L
B
3-1/2" Hex
Bolts
2" Hex
Bolt
2" Hex
Bolt
2" Hex
Bolt
3" Hex
Bolts
All lag
screws 3"
2" Lag
Screw
Front of
Tower

MODEL PS18EAS
19862-700 Rev A (07-20)
© Copyright 2014, Creative Playthings Page 13
ASSEMBLY INSTRUCTIONS
STEP 12 — Stringer:
Fasten the Stringer (T) to the Platform Front and Platform
Back using two 1/4 x 3" Lag Screws and Flat Washers as
shown.
STEP 13 — Deck Boards:
Locate the nine Deck Boards (X) and three Narrow Deck
Boards (Y). Lay them across the platform supports and
stringer in the arrangement shown at right. Align the ends of
the Deck Boards. The Narrow Deck Boards t between the
uprights.
Starting at the front of the gym fasten each board using #10
x 1-5/8" Screws. For the rst four boards, leave a gap of 1/8"
or less to limit the possibility of clothing being snagged when
children use the slide. Space the rest of the boards evenly.
Note that the Narrow Deck Board between the Midposts
need not align exactly with the Midposts.
STEP 14 — Assemble Roof Panels:
Assembly of the Roof Panels will be easiest on a work table
or other at surface.
Lay Out Roof Rafters:
Butt the square-cut end of two Rafters (V) against a straight
at surface. Align the Rafters so they are parallel and the
ends aligned and square. The distance between the Rafters
should be 30". Measure from corner to corner both ways.
When the two diagonal measurements are the same, the
rafters are square.
30"
30" V
V
3" Lag
Screw
3" Lag
Screw
T
X
X
Y#10 x 1-5/8"
Screws
< 1/8" gap between
1st four boards
Evenly space the
back eight boards

© Copyright 2014, Creative Playthings
MODEL PS18EAS
19862-700 Rev A (07-20) Page 14
ASSEMBLY INSTRUCTIONS
Fasten Roof Boards:
Start at the angled end of the Roof Rafters. Rest one Roof
Board (AD) on top of the Rafters ush to the angled end.
Use a 1/8" diameter drill to make pilot holes before fastening
the Roof Board to the Rafter using four #10 x 1-5/8" Screws.
Drill and screw the rst hole at an angle, as shown, to avoid
the angled cut of the rafter.
Continue with the next three Roof Boards, setting each
against the previous Roof Board and fastening them. Once
the position of the Rafters is stable, lay the rest of the Roof
Boards in place. The sixth Roof Board should overhang the
end of the Rafters by approximately 1/2". If the overhang
is less than 1/2", evenly space the Roof Boards to achieve
an overhang. If the overhang is greater, alternative holes
should be made in the nal Roof Board. Fasten the Roof
Boards using #10 x 1-5/8" Screws.
Center Roof Rafter:
Find the center of the Roof Panel Assembly, halfway be-
tween the Rafters. Align the a Roof Rafter (U) to the center
of the Roof Panel and fasten it in place using 1/8" pilot holes
and #10 x 1-5/8" Screws as with the other Rafters.
Assemble Second Roof Panel:
Flip the rst Roof Panel to use as a template to assemble
the remaining Roof Panel. Place the remaining Rafters tight
against the Rafters on the assembled panel. Align the ends.
Fasten Roof Boards to the Roof Rafters using 1/8" diameter
pilot holes and #10 x 1-5/8" Screws, as with the rst Roof
Panel.
STEP 15 — Roof Panels to Roof Uprights:
Fasten one Roof Panel assembly to the left Roof Uprights
using 1/4 x 4-1/2" Hex Bolt Assemblies.
Repeat with the other Roof Panel on the right uprights. Rest
the angled ends of the Roof Panels against each other.
Hint: If you are having trouble making this connection, loos-
en the connection between one Roof Upright and the Wall
Support. The Roof Upright can now be moved to allow better
access. Be sure to re-secure the connection after the Roof
Panels are in place.
AD
1/4 x 4-1/2"
Hex Bolt
1/2"

MODEL PS18EAS
19862-700 Rev A (07-20)
© Copyright 2014, Creative Playthings Page 15
ASSEMBLY INSTRUCTIONS
STEP 16 — Ceiling Joists:
Adjust the Roof Panels so the angled ends are even with
each other. Fasten an End Joist (Z) to the outside of the
Rafters on each end. Use two 1/4 x 2" Hex Bolt Assemblies
through the upper holes of each End Joist.
Fasten the Ceiling Joist (U) to the center Rafters using two
1/4 x 2" Hex Bolt Assemblies.
Adjust the Roof so it looks even. Adjust the End Rafters to
look straight and centered in place. Use a 3/16" diameter
drill to make pilot holes in the Rafters through the lower
holes in the End Joists. Secure the End Joists to the Rafters
using 1/4 x 2" Lag Screws and Flat Washers through the
bottom holes.
STEP 17 — Lower and Short Wall Supports:
Fasten the Lower Wall Support (AB) to the Back Left Post,
left Midpost and Front Left Post using 1/4 x 2" Hex Bolt As-
semblies through the upper holes. Secure the three lower
holes in the Lower Wall Support using 1/4 x 2" Lag Screws
and Flat Washers.
Fasten the Short Wall Support (AC) to the right Midpost and
Front Right Post using 1/4 x 2" Hex Bolt Assemblies through
the upper holes. Secure the lower holes using 1/4 x 2" Lag
Screws and Flat Washers.
Drill 3/16" diam-
eter pilot holes. U
Z
STEP 18 — Swing Mounts:
Fasten the two Swing Mounts (AI) to the Left Wall Support
and Lower Wall Support using two 1/4 x 3-1/2" Hex Bolts
each. Be sure to orient the Swing Mounts so the holes on the
sides are closer to the top.
3-1/2" Hex Bolts
AI
Parts omitted
for clarity
AB
AC
1/4 x 2" Hex Bolts
top, 1/4 x 2" Lag
Screws bottom
1/4 x 2" Lag
Screw
1/4 x 2" Lag
Screw
1/4 x 2"
Hex Bolts

© Copyright 2014, Creative Playthings
MODEL PS18EAS
19862-700 Rev A (07-20) Page 16
ASSEMBLY INSTRUCTIONS
STEP 19 — Short Wall Slats & Entrance Slats:
Fasten three Short Wall Slats (AG) to the Left Wall Support and
Lower Wall Support using four #8 x 1-1/4" Screws each. Even-
ly space the Slats between the front left post and the left Mid
Post. The gap between the Slats will be approximately 1-5/8".
Fasten six Short Wall Slats (AG) to the Left Wall Support and
Lower Wall Support using four #8 x 1-1/4" Screws each. Even-
ly space the Slats between the back left post and the left Mid
Post. The gap between the Slats will be approximately 1-7/8".
Fasten three Short Wall Slats (AG) to the Right Top Support
and Short Wall Support using four #8 x 1-1/4" Screws each.
Evenly space the Slats between the front left post and the left
Mid Post. The gap between the Slats will be approximately
1-5/8".
Fasten the Entrance Slats (AL) to the inside of the Right Wall
Support and Rock Wall Mount using #10 x 1-5/8" Screws. Leave
a gap of 19" between the Entrance Slats.
STEP 20 — Narrow Wall Slats:
Fasten six Narrow Wall Slats (AK) to the Platform Back and
End Support using four #8 x 1-1/4" Screws each. Evenly space
the Slats between the Back Left Post and Back Right Post. The
gap between the Slats will be approximately 2-3/4".
Parts omitted
for clarity
AG
AG
AK
AL
19"
AJ
STEP 21 — Safety Rail:
Hold the Safety Rail (AJ) in place against the left posts, un-
der the Swing Mounts, approximately 23" above the ground.
Fasten the Safety Rail to the posts with two 1/4 x 3-1/2" Lag
Screws and Flat Washers using the pre-drilled pilot holes.

MODEL PS18EAS
19862-700 Rev A (07-20)
© Copyright 2014, Creative Playthings Page 17
ASSEMBLY INSTRUCTIONS
STEP 23 — Rock & Spacer Boards:
Fasten one Rock Board (AH) to the top of the Climber Rails
using two #10 x 2" Screws. Drill 1/8" diameter pilot holes for
the screws to prevent splitting of the Climber Rails.
Evenly space Rock Boards and Spacer Boards (AN) be-
tween the top Rock Board and Bottom Rope Board in the
pattern shown at left. Secure each board to the Climber
Rails using four #10 x 2" Screws with 1/8" pilot holes. The
gap between boards will be approximately 7/8". Use a Rock
Board or Spacer Board on edge to gauge the gap.
STEP 24 — Climbing Rocks:
Fasten one Climbing Rock (AR) to each Rock Board using
two 1/4 x 1-1/2" Hex Bolts, 1/4 Lock Washers, 8mm Flat
Washers and 1/4" Weld Nuts.
1/4 x 1-1/2"
Hex Bolt
1/4" Lock
Washer
8mm Flat
Washer
1/4 x 1" Hex Bolt
AR
#10 x 2"
Screws
AF
AM
1/4 x 1-1/2" Hex Bolt
AN
AH
AH
AN
Use a Rock Board or
Spacer Board on edge to
gauge the gap.
Drill 1/8" diameter
pilot holes for the
screws to prevent
splitting.
STEP 22 — Climber Uprights, Rope Board:
Fasten one Access Bracket to the top of each Climber
Upright (AF) using one 1/4 x 1-1/2" Hex Bolt Assembly.
Fasten each Bracket and Rail assembly to the Rock Wall
Mount using one 1/4 x 1" Hex Bolt Assembly.
Fasten the Rock & Rope Board (AM) to the bottom
of the Climber Rails using two #10 x 2" Screws, in
the bottom corner holes only. Use a 1/8" diameter
drill to create pilot holes for the screws to prevent
splitting of the Climber Rails.
Measure the diagonal distance
from the top left corner of the
Climber Rail to the bottom right
corner of the Rock & Rope Board. Measure the opposite
diagonal. Adjust the position of the Climber Rails until the di-
agonal measurements are equal. Finish securing the board.
Layout the Rock Boards and Spacer Boards as shown. De-
termine which boards look best on which side.
#10 x 2"
Screws
Gaps approx. 7/8"
AH
AH
AH
AH
AH Drill 1/8" diameter pilot
holes for the screws to
prevent splitting.
AM
AN
AN
AN
AN

© Copyright 2014, Creative Playthings
MODEL PS18EAS
19862-700 Rev A (07-20) Page 18
ASSEMBLY INSTRUCTIONS
STEP 26 — Access Ladder:
Fasten one Access Bracket to inside of each Ladder Rail
using 1/4 x 1-1/2" Hex Bolt Assemblies as shown at right.
Note: Temporarily place the Slide into position to help judge
the best placement for the Access Ladder. Make sure that all
hardware has room to t before drilling.
See the standard placement below right.
Lean the Access Ladder against the gym with the Access
Brackets at against the Platform Front and the lower edge
of the Brackets ush with the lower edge of the Platform
Front.
Drill 5/16" diameter holes through the holes in the Brackets
and through the Platform Front. Secure the Brackets using
1/4 x 1" Hex Bolt Assemblies.
1/4 x 1-1/2"
Hex Bolt
1/4 x 1" Hex Bolts1/4 x 1" Hex Bolts
Drill 5/16" dia. holes
1-3/8"
STEP 25 — Access Ladder Rungs & Slat:
Fit four 15" Rungs (AE) into the holes in the Left Ladder Rail
(R) and the Right Ladder Rail (S). Set the assembly at on a
solid surface. Make sure the rungs are completely inserted
with the ends of the rungs snug against the bottom of the
holes.
Use #10 x 1-1/2" Self-Drilling Screws, through the holes
provided, to fasten the rungs in place. (The Self-Drilling
Screws have a drill-bit tip. Point the screw toward the center
of rung diameter and press rmly. Do not sink the head of the
screw beyond ush with the surface of the wood.
Use four #10 x 1-5/8" Screws to fasten the Ladder Slat (AA)
to the Ladder Rails. The top edge of the Ladder Slat should
be about 2-1/4" below the top of the Ladder Rails as shown.
Make sure the gap between the top Rung and the Ladder
slat is less than 3-1/2"; adjust if necessary. Drill 1/8" diam-
eter pilot holes 1" deep for each #10 x 1-5/8" Screw.
AA
S
R
AE
The top of the ladder is
the end with holes in the
rails for brackets
2-1/4"

MODEL PS18EAS
19862-700 Rev A (07-20)
© Copyright 2014, Creative Playthings Page 19
ASSEMBLY INSTRUCTIONS
STEP 29 — Climbing Rope:
Push one end of the Climbing Rope (AP) through the hole in
the Right Wall Support. Tie a gure-eight knot at the end of
the rope, inside the gym. Leave at least 3" of rope extending
beyond the knot inside the gym.
From the outside of the gym, tie an overhand knot approxi-
mately every 11" along the length of the rope. Make sure
each knot is tight.
Push the loose end of the rope through the hole in the Bot-
tom Rope Support. Pull the rope taut and tie a gure-eight
knot to secure it.
Set the Climber Rails into the playground surface to en-
sure that the bottom rope connection is as close to the
ground as possible.
IMPORTANT: Check the rope often. At no time should
the bottom end of the rope be untied or the rope loose
enough to form a loop. This presents extreme danger to
your children.
STEP 27 — Hand Grips to Entrance Slats:
Fasten one Hand Grip (AO) to each Entrance Slat above
the Rock Climber using two 1/4 x 1" Hex Bolt Assemblies
for each.
1/4 x 1"
Hex Bolt
AO
8"
1/4" x 1-1/2" Lag Screws
AO
Figure Eight
Knot
Overhand
Knot
If the rope is too
long you can tie
extra knots along
the length of the
rope. If too short,
remove knots.
AP
STEP 28 — Hand Grip to Front Post:
Hold one Hand Grip (AO) against the front face of the front
right post above the Access Ladder. The lower hole should
be 8" above the top of the platform.
Fasten with 1/4 x 1-1/2" Lag Screws and Flat Washers using
the holes provided.

© Copyright 2014, Creative Playthings
MODEL PS18EAS
19862-700 Rev A (07-20) Page 20
ASSEMBLY INSTRUCTIONS
STEP 31 — Swing Beam & Swings:
Install the Swing Beam as instructed by the assembly
guide included with the Beam.
Hang the Swings and Ring Trapeze in the positions
shown at right.
U.S. safety standards require a minimum clearance
of 8" from the bottom of each Swing Accessory to
the ground. U.K. (& E.U.) safety standards re-
quire a minimum clearance of 350mm (13-3/4")
between the bottom of each Swing Accessory
and the ground.
The height of each Swing Accessory is ad-
justed by using a different link in the chain.
Be sure to hang the Swings Accessories
with ground clearance greater than or
equal to the safety standard for your
region.
STEP 30 — Slide:
Place your Slide in the opening in the tower front as shown.
Check that the Slide extends out perpendicular from the play
set.
Using the holes in the slide for guides, drill 5/16" diameter
holes through the Platform Boards and secure the Slide us-
ing 1/4" x 1" Truss Head Bolts from the top and 1/4" Weld
Nuts from below.
Note: Depending on the Slide, you may nd the holes you
drill encounter a framing member. If so, stop drilling after
piercing the Deck Board. Loosen the Deck Board and insert
the Weld Nuts from the underside. If desired, a 1" spade drill
bit can be used to clear a space for the base of the Weld Nut
in the Framing Member. Re-attach the Platform Board and
continue securing the Slide.
STEP 32 — Ground Stakes:
Hammer two Ground Stakes next to the Front Left Post and Back Right Post as shown.
The top of the Ground Stake should be minimum of 1/8" below the top of the Sandbox Sides.
Secure each stake to the adjacent Sandbox Side using two #10 x 2" Screws through the
pre-drilled holes.
Hammer Ground Stakes next to the Access Ladder and Cargo Upright as shown. Secure
each stake with two #10 x 2-1/2" Screws through the pre-drilled holes. Secure the Beam
Legs in the same manner.
Note: Do NOT use concrete to set Ground Stakes. Pound a metal spike or rod into the
ground to start a hole in hard or rocky ground.
Inspect your work; make sure all fasteners are secured properly and the
area is clear of hazards before allowing children on the Swing Set.
#10 x 2-1/2"
Screw
U
Save all instruction sheets and receipts in case it becomes necessary to contact
Creative Playthings for warranty service and/or part replacement. The warranty
can be found in your Owner’s Manual.
AT