Creative Playthings NORTHBRIDGE WITH TENT User manual

NORTHBRIDGE W/ TENT
ASSEMBLY MANUAL Creative Playthings®
Please read the owner’s manual before the
assembly of your play set. It provides
additional information on the care and use of
your play set.
You must carefully read the entire instruction
manual before proceeding with the assembly
or use of your new play set.
Creative Playthings takes great care to design
its products with your child’s safety in mind.
However, only with careful supervision
and proper safety instructions, can you be
assured of safe play time on any product
designed for children.
This product is intended for single
family home/residential use only and
not intended for use in any public
setting. Placement in any public
setting constitutes a misuse of this
product.
All hardware on this set is specially coated
for corrosion resistance.
If non-Creative Playthings hardware is used,
it must be galvanized or stainless steel.

© Copyright 2016, Creative Playthings
NORTHBRIDGE WITH TENT
19949-200 Rev D (03-22) Page 2
PLAYSET SAFETY
Observing the following statements & warnings reduces the likelihood of serious or fatal injury:
• Children should use equipment only in its intended manner.
• Children should not wear loose or stringed clothing while using playground equipment.
• Children should not play on equipment in wet weather conditions due to potentially slippery surfaces.
• Children should NOT walk too closely in front of, behind, or between moving swings and trapezes.
• Children should NOT swing empty swing seats.
• Children should NOT jump off swings and/or trapeze while they are in motion.
• Children should NOT twist swing chains because this will reduce the strength of the chains.
• Children should sit in the center of the swings with their full weight on the seats.
• Children should NOT be on the top surface of the swing beam.
• Children should NOT use the equipment in a manner other than intended.
• Children should NOT get off the equipment while it is in motion.
• On-site adult supervision is required at all times for children of all ages.
• Until assembly is complete, DO NOT let your children use the Play Set.
• Never fasten anything not approved by Creative Playthings to your Play Set. Accessories or items not ap-
proved by Creative Playthings include; Dog runs, clothes lines, electrical devices, or bird feeders etc.
• Suspended ropes, chains, and cables must be secured at both ends.
• Suspended ropes, chains, and cables must not be capable of looping back on themselves.
• Do not allow more than 120 lbs. on Single occupancy swing accessories such as the Sling Swing and Trapeze.
• Do NOT allow more than 175 lbs. on multiple use swing accessories such as the Back-to-Back Plastic Glider.
• Do NOT allow more children on the Play Set than can simultaneously use all the swing stations at one time.
• Children MUST NEVER wear bicycle helmets while playing on the play-set.
Assembly Safety:
• Adult assembly required
• Face slide away from the sun.
• Keep the work area clean and clear of obstructions.
• Children should stay out of the work area until the safe play area is cleared of obstacles, the Play Set has been
completely assembled, all hardware has been tightened and checked, and all tools have been picked up.
• Keep children off the Play Set until it has been completely assembled.
• Parts of the assembly process may require help from another competent adult.
• Do not stand on the platform until the Play Set has been completely assembled, use a step ladder if you can
not reach high enough.
• Follow the manufacturers' safety recommendations for the tools and equipment you use.
• Avoid assembling your Play Set in poor weather conditions.
• Wear proper clothing and safety equipment (safety glasses, boots, and gloves) while assembling your Play Set.
FOR SAFETY SAKE, PLEASE TAKE TIME TO READ ALL INSTRUCTIONS COMPLETELY AND
CAUTION YOUR CHILDREN APPROPRIATELY.

Assembly
NORTHBRIDGE WITH TENT
19949-200 Rev D (03-22)
© Copyright 2016, Creative Playthings Page 3
SAFE PLAY AREA
SELECTING THE CORRECT LOCATION FOR YOUR PLAY PRODUCT IS IMPORTANT FOR
YOUR CHILDREN’S SAFETY AND THE PRODUCT’S LONGEVITY.
Playset Dimensions:
• All Northbridge gyms have ground dimensions of 11'-6" x 21'-3".
• Each Northbridge play set requires a level ground surface of 28'-2" x 33'-3' for a Safe Play Area
• Additional accessories may increase the size of the Safe Play Area.
• The maximum fall height for your play set is 87-1/2" as measured from the top of the Swing Beam.
Safe Play Area:
• The Safe Play Area refers to a zone extending 6' (2 meters) beyond the Playset on all sides, including the slide
and the space above the Playset. Because children may deliberately jump from a moving swing, the Safe Play
Area must be extended to 14' (4.27 meters) in front of and behind a swinging Accessory.
• The ground surface must be level. Installing your Playset on sloping ground can cause it to lean or “rack”. This
leaning puts additional stress on all connections and joints and in time will cause those connections to loosen
and fail.
• The Safe Play Area must be free of all structures, landscaping, trees and branches, rocks, wires, and other
obstacles to safe play. Children can be seriously injured running, or swinging into these obstacles.
• Remove all tripping hazards from the Safe Play Area. Tripping hazards include; roots, stumps, rocks, landscap-
ing, sprinkler heads, railroad ties, plumbing and electrical connections.
• Do not install your Playset over concrete, gravel, asphalt, packed earth, or any other hard surface. The follow-
ing is a list of recommended ground covers from the Consumer Product Safety Commission.
RECOMMENDED GROUND COVER
Suggested Material Uncompressed Depth
Double Shredded Bark Mulch 9"
Uniform Wood Chips 12"
Fine Gravel 12"
Fine Sand 12"
• Any edging used to contain the ground cover must be beyond the Safe Play Area. (i.e.. Landscape Timbers)
A FALL ONTO A HARD SURFACE COULD RESULT IN SERIOUS
INJURY.
Safe play area using
recommended ground cover.
Whichever is greater
Landscape Timbers 6' from
play structure.
6'
(2 M)
6'
(2 M)
6'
(2 M)
6'
(2 M)
14'
(4.27 M)
14'
(4.27 M)

© Copyright 2016, Creative Playthings
NORTHBRIDGE WITH TENT
19949-200 Rev D (03-22) Page 4
FASTENERS
We have packaged more hardware than is required for assembly.
Truncated to t on page
1/4 x 3" Truss Head Bolt
#10 x 4-1/2" Screw
#10 x 1-5/8" Screw
#10 x 2-1/2" Screw
#10 x 2-1/2" Self-Drill Screw
8mm Flat Washer
1/4 x 1-1/2" Lag Screw
1/4" Lock
Washer
1/4" Weld
Nut
1/4 x 1-1/2" Hex Bolt
5/16" Flat Washer
5/16" Lock
Washer
5/16" Weld
Nut
5/16 x 3-1/2" Lag Screw
5/16 x 4-1/2" Lag Screw
3/8 x 5-1/2" Lag Screw
3/8 x 8" Lag Screw
5/16 x 4" Lag Screw
5/16 x 3" Hex Bolt
5/16 x 4-1/2" Hex Bolt
5/16 x 6" Hex Bolt
3/8" Flat Washer
3/8" Lock
Washer
3/8" Weld
Nut
Hex Bolt 3/8 x 4-1/2"
Hex Bolt 3/8 x 6"
5/16 x 2-1/2" Hex Bolt
#10 x 2-1/2" T25 Screw

Assembly
NORTHBRIDGE WITH TENT
19949-200 Rev D (03-22)
© Copyright 2016, Creative Playthings Page 5
FASTENERS
50559-700 Northbridge Hardware
77 12002-206 Flat Washer 5/16"
61 12017-206 Lock Washer 5/16"
61 17001-105 Weld Nut 5/16"
4 17003-1011 Hex Bolt 5/16 x 2-1/2"
13 17003-1211 Hex Bolt 5/16 x 3"
33 17003-1811 Hex Bolt 5/16 x 4-1/2"
8 17003-2411 Hex Bolt 5/16 x 6"
2 17036-1402 Lag Screw 5/16 x 3-1/2"
4 17036-1602 Lag Screw 5/16 x 4"
8 17036-1802 Lag Screw 5/16 x 4-1/2"
26 12002-207 Flat Washer 3/8"
17 12017-207 Lock Washer 3/8"
17 17001-103 Weld Nut 3/8"
13 17003-1813 Hex Bolt 3/8 x 4-1/2"
4 17003-2413 Hex Bolt 3/8 x 6"
4 17036-2203 Lag Screw 3/8 x 5-1/2"
4 17036-3203 Lag Screw 3/8 x 8"
152 17020-115 Screw #10 x 1-5/8"
50 17138-1025 T25 Screw #10 x 2-1/2"
16 17020-113 Screw #10 x 2-1/2"
11 17020-120 Screw #10 x 4-1/2"
13 17120-902 Self-Drilling Screw #10 x 2-1/2"
34 12002-203 Flat Washer 8mm
26 12017-205 Lock Washer 1/4"
28 17001-104 Weld Nut 1/4"
26 17003-609 Hex Bolt 1/4 x 1-1/2"
8 17036-601 Lag Screw 1/4 x 1-1/2"
2 17119-1209 Truss Head Bolt 1/4 x 3"
CREATIVE PLAYTHINGS PLAY SETS USE A FEW STANDARD CONNECTIONS. BECOME FAMILIAR WITH
THESE CONNECTIONS TO EASE ASSEMBLY AND ENSURE A SAFER PLAY PRODUCT FOR YOUR CHILDREN.
Hex Bolt & Weld Nut Assembly Procedure:
Assembly Layout:
Align the holes in the parts to be fastened. Start
preliminary tightening of bolt into weld nut by
hand. Tighten each bolt with a wrench until the
lock washer is fully compressed between the
head of the bolt and the at washer.
Correct Assembly:
Bolt has been screwed securely into weld nut
and the connection is tight. Check connec-
tions periodically for tightness during the life
of the Playset . Do not over tighten.
Incorrect Assembly:
During assembly or maintenance the bolt pro-
trudes 1/8" past the weld nut. Call customer
service or replace the bolt at a local hardware
store. You may be overtightening or using the
wrong size bolt.
Failure to replace this bolt with a shorter
one could result in serious injury.
Typical Installation - Lag Screws:
• Pilot drill with the appropriate
diameter drill bit and then use
a socket to tighten.
• DO NOT over tighten
Typical Installation - Wood Screws:
• Use an electric drill or screw gun to drive screws.
• Drill 1/8" pilot holes where required.
• We recommend that you lubricate the
threads of the screws with beeswax or
soap to ease installation and minimize
breaking screws.
• It is very important to make certain
that the tops of all screws are ush
with the surface of the wood and
there are no protruding sharp edges.
Lag Screw
Flat Washer
Hardware Bags
We have packaged more hardware than is required for
assembly.

© Copyright 2016, Creative Playthings
NORTHBRIDGE WITH TENT
19949-200 Rev D (03-22) Page 6
PLAYSET VIEW
A
B
C
D F
G
H
AJ
J K U M
N AB
AB
AC AD
AE
AI
I
AM AL
AK AS
AT
S V W Y Z
AA
AH
O
L

Assembly
NORTHBRIDGE WITH TENT
19949-200 Rev D (03-22)
© Copyright 2016, Creative Playthings Page 7
COMPONENT VIEW
AA 2 35321-102 Leg 4 x 4 x 80"
AB 1 35322-102 Rung Leg 4 x 4 x 80"
AC 1 35323-102 Step Leg 4 x 4 x 80"
AD 2 35324-102 Main Beam 2 x 10 x 76"
AE 2 35327-102 Side Support 2 x 4 x 27-7/8"
AF* 1 35335-102 Stringer 2 x 4 x 66-7/8"
AG* 1 35336-102 Swivel Stringer 2 x 4 x 66-7/8"
AH 1 40508-100 Cargo Net
Northbridge Tent With Posts
AI 2 35288-102 End Tent Support 2 x 6 x 83-1/2"
AJ 4 35344-102 Short Corner Post 4 x 4 x 40"
AK 2 40607-102 Tent Post Assembly
AL 3 14235-400 Tent Pipe 1-3/8" Dia. x 48-3/4"
AM 1 40606-400 Tent, Green
J 6 35246-102 Rock Board 5/4 x 6 x 27-1/4"
K 1 35247-102 Rope Board 5/4 x 6 x 27-1/4"
L 4 35248-102 Spacer Board 5/4 x 6 x 27-1/4"
M 1 35538-102 Rock Base Rail 2 x 6 x 59-3/4"
N 1 35539-102 Rope Base Rail 2 x 6 x 59-3/4"
O 1 35328-102 Step Support 2 x 4 x 64-7/8"
P* 1 35329-102 Rung Support 2 x 4 x 64-7/8"
Q* 2 35330-102 Center Block 4 x 4 x 5"
R* 2 35331-102 Inside Beam 2 x 6 x 66-7/8"
S 1 35332-102 Ladder Plat End 2 x 6 x 40-1/2"
T* 1 35333-102 Stair Platform End 2 x 6 x 40-1/2"
U 1 35449-102 Narrow Spacer 54 x 4 x 27-1/4"
V 1 50277-100 Rock Pack (12), Green
W 1 40400-100 Climbing Rope
X* 1 15133-400 Slide Mount, Green
Y 5 14203-400 Steel Rung, Green 1" Dia x 18"
Z 10 15154-400 Rung Collar, Green, 1" Dia x 7/8"
A 1 33978-102 Ladder Slat 5/4 x 4 x 18-3/4"
B 9 35202-102 Wall Slat 5/4 x 6 x 29-1/2"
C 5 35334-102 Ladder Step 2 x 6 x 15-1/2"
D 8 35337-102 Deck Board 5/4 x 6 x 47"
E* 1 35338-102 Ctr Deck Board 5/4 x 6 x 46-7/8"
F 4 35339-102 End Deck Board 5/4 x 6 x 40-3/8"
G 1 35340-102 Upper Support 2 x 6 x 47"
H 1 35341-102 Upper Rope Support 2 x 6 x 47"
I 4 15034-100 Plastic Handgrip, Yellow
1 50559-700 Northbridge Hardware
Component Part Identication:
Take inventory of all parts, making sure nothing is missing or
defective. If you nd that parts are missing or defective call
the Creative Playthings Customer Service Department at
1-800-598-4997. * Not visible in illustration on Page 6
NORTHBRIDGE BOX 1 - 63085-641
NORTHBRIDGE BOX 2 - 63085-652
NORTHBRIDGE BX 3 - 63085-603
63085-654
Boxes for Northbridge with Tent
63085-641 Northbridge Box 1
63085-652 Northbridge Box 2
63085-603 Northbridge Box 3
63085-654 Northbridge Tent w/ Posts
63045-505 Tire Swing & Swivel
8570-202 10 Ft. Green Wave Slide
63080-101 3 Position Swing Beam
AA934-204 2 Swings, 1 Trapeze
Other Parts
AS 1 8570-202 10 Ft. Green Wave Slide
63080-101 Classic Pine 3 Position Swing Beam (Swing
Mount included with Swing Beam)
AT 63045-505 Tire Swing and Swivel

© Copyright 2016, Creative Playthings
NORTHBRIDGE WITH TENT
19949-200 Rev D (03-22) Page 8
MAINTENANCE INSTRUCTIONS
YOUR CREATIVE PLAYTHINGS PLAY SET IS STAINED AT OUR FACTORY.
STAINING IS NOT NEEDED AT THE TIME OF INITIAL ASSEMBLY.
Re-staining Information:
• Pigmented, exterior, water repellent stains are recommended and will provide an excellent barrier against moisture
without hiding the natural wood grain or leaving a lm that may later crack or peel.
• We recommend that you apply stain according to the instructions and precautions recommended by the stain manufacturer.
• It should take three or more quarts to cover your set.
• Contact your local dealer or call Creative Playthings for our staining products.
• All rungs are pre-nished at the factory and do not require any nishing at the time of initial assembly.
• Do not paint, or varnish rungs or steps.
• Avoid using nishes that create slippery surfaces.
Maintenance:
• Wooden playground equipment will last for years with proper maintenance. Maintenance of the Playset nish will vary
depending on weather climate.
• As a safety precaution, check all hardware, such as nuts and bolts, for tightness twice a month during use and at the
beginning of each play season. Tighten as required and specied in these instructions. Do not over-tighten.
• Check structure twice monthly during usage for any evidence of deterioration. If upon inspection, hardware has sharp edges,
rusted or structural pieces have signs of premature failure; replace them through Creative Playthings Customer Service.
• Oil all metallic moving parts monthly during the usage season.
• The swings, trapeze, tent, rope ladders, and any other removable plastic accessories should be removed and taken
indoors when outside temperatures drop below 32° F (0° C).
• Wood will expand and contract as it adjusts to temperature changes and varying moisture conditions. Checks or cracks
are a natural characteristic of all wood and will not affect the strength or durability of the wooden components.
• To maintain the nish of your set, a light sanding and an application of an exterior stain will repair scratches and prevent
wood from aging prematurely.
• Finishes applied to ladder rungs must not create a slippery surface.
• The wood parts of your Playset should never be disposed of by burning.
• Dispose of all parts so as not to create a hazard.
• "Check all coverings for bolts and sharp edges and replace when required."
• "Check swing seats, chains, ropes, and other means of of attachments for evidence of deterioration". Replace through
Creative Playthings Customer Service.
Tools & Materials Suggested for Finishing & Assembly:
• Claw Hammer
• Carpenter’s Level
• Electric Drill
• 1/8", 3/16", 1/4", 5/16", 3/8", 7/16" Drill Bits (High Speed)
• Driver drill (Medium Phillips and T-25 Torx bits)
• Box Wrench or Sockets (7/16", 1/2", & 9/16)
• Pliers
• 10 ft. Tape Measure
• Framing Square
• 6 ft. Step Ladder
• Beeswax or Soap (Used to lubricate screw threads)

Assembly
NORTHBRIDGE WITH TENT
19949-200 Rev D (03-22)
© Copyright 2016, Creative Playthings Page 9
ASSEMBLY INSTRUCTIONS
STEP 1 – Platform Frame:
Locate the Ladder Platform End (S),
Stair Platform End (T), and the two In-
side Beams (R). Lay them out as shown
at right. Orient the Inside Beams with the
larger holes nearer the bottom. Orient the
Platform Ends so the holes in the ends of
the boards are near the top. Make sure
the other holes in the Platform Ends are
aligned as shown.
Use four 5/16 x 4-1/2" Lag Screws with
four 5/16" Flat Washers to fasten each
Platform End to the end of the Inside
Beams.
STEP 2 – Main Beam & Posts:
Fasten the center of one Main Beam (AD) and Center Block (Q) to the front of the Inside Beam using two 5/16 x 6" Hex Bolt
Assemblies*. Repeat with the other Main Beam and Center Block at the back of the platform frame. Wait to fully tighten the
fasteners until the posts are in place.
Fasten one Post (AJ) to the Main Beam and platform frame at all four corners. Use 3/8 x 6" Hex Bolt Assemblies in the
lowest holes, 5/16 x 6" Hex Bolt Assemblies in the middle holes and 3/8 x 4-1/2" Hex Bolt Assemblies in the top holes. Do
not fully tighten these fasteners until after installing the legs of the tower in later steps.
Larger hole
on bottom
Align with end
hole at the top
Larger hole
on bottom
Tent Roof Version
5/16 x 6" Hex Bolt
5/16 x 6" Hex Bolt
3/8 x 4-1/2" Hex Bolt
5/16 x 4-1/2"
Lag Screw
3/8 x 6" Hex Bolt
R
R
T
S
AD
AJ
AJ
AD
Q
* Note: a Hex Bolt Assembly consists of one Hex
Bolt passing through one Lock Washer and one
Flat Washer, threaded into one Weld Nut.
Hint: Before tapping weld nuts in place with a hammer,
clear any wood fragments from the holes with a pocket
knife. Weld nuts work best when the t is tight.
Back of the Gym
Back of the Gym
Right side of the Gym
Right side of the Gym
Center

© Copyright 2016, Creative Playthings
NORTHBRIDGE WITH TENT
19949-200 Rev D (03-22) Page 10
ASSEMBLY INSTRUCTIONS
STEP 3 – Upper Supports:
Fasten the Upper Support (G) to the Posts on the
left side of the gym using four 5/16 x 4-1/2" Hex Bolt
Assemblies.
Fasten the Upper Rope Support (H) to the Posts on
the right side of the gym using four 5/16 x 4-1/2" Hex
Bolt Assemblies. Note the position of the rope hole in
the Upper Rope Support. The hole should be closest
to the front of the gym.
STEP 5 – Weld Nuts on Back:
Insert four 3/8" Weld Nuts into the Main Beam at
the back of the tower in the positions shown. Make
sure the threads inside the Weld Nuts are clear as
it may be hard to access the Weld Nuts later.
STEP 4 – End Tent Supports:
Fasten one End Tent Support (AI) to the front Posts
using four 5/16 x 4-1/2" Hex Bolt Assemblies. Arrange
the End Tent Support so the holes at the center are
closest to the top of the board. Repeat with the other
End Tent Support at the back of the tower.
AI
H
G
Back of the Gym
Right Side of the Gym
Front of the Gym
Right side of the Gym
Right side of the Gym
Back of the Gym
5/16 x 4-1/2" Hex Bolt
3/8" Weld Nut
5/16 x 4-1/2"
Hex Bolt
Align these holes
closer to the top

Assembly
NORTHBRIDGE WITH TENT
19949-200 Rev D (03-22)
© Copyright 2016, Creative Playthings Page 11
ASSEMBLY INSTRUCTIONS
AB
STEP 6 – Tip onto Back:
With the help of another person, gently tip the assembly
onto its back, with the Weld Nuts facing the ground.
STEP 7 – Rung Leg:
Slide the Rung Leg (AB) into place between the back
Main Beam and the back Inside Beam as shown. Place
the angled face of the leg ush to the back right Post
and align the holes with the holes in the Main Beam.
Fasten the Rung Leg to the back Main Beam with 3/8
x 4-1/2" Hex Bolt Assemblies using the Weld Nuts in-
serted previously.
Right side of the Gym
3/8 x 4-1/2" Hex Bolt
STEP 8 – Rock Base Rail:
Fasten the Rock Base Rail (M) to the Rung
Leg as shown, using two 5/16 x 4-1/2" Hex
Bolt Assemblies.
M
5/16 x 4-1/2" Hex Bolt
Note: Many of the illustrations on the next pages
show a different model of the gym with taller posts.
Assembly is the same.
Left side of
the Gym
Right side of
the Gym

© Copyright 2016, Creative Playthings
NORTHBRIDGE WITH TENT
19949-200 Rev D (03-22) Page 12
ASSEMBLY INSTRUCTIONS
STEP 9 – Right Front Leg:
Slide one Leg (AA) into place between the
front Main Beam and the front Inside Beam
as shown. Place the angled face of the leg
ush to the front right Post and align the holes
with the holes in the Main Beam.
Fasten the Leg to the front Main Beam with
3/8 x 4-1/2" Hex Bolt Assemblies.
Fasten the Leg to the Rock Base Rail as
shown, using two 5/16 x 4-1/2" Hex Bolt
Assemblies. Be sure to note the position of
the weld nuts.
STEP 11 – Rope Base Rail:
Fasten the Rope Base Rail (N) to the back
left Leg as shown, using two 5/16 x 4-1/2"
Hex Bolt Assemblies.
STEP 10 – Left Back Leg:
Slide one Leg (AA) into place between the
back Main Beam and the back Inside Beam
as shown. Place the angled face of the leg
ush to the back left Post and align the holes
with the holes in the Main Beam.
Fasten the Leg to the back Main Beam with
3/8 x 4-1/2" Hex Bolt Assemblies using the
Weld Nuts inserted previously.
N
AA
AA
3/8 x 4-1/2" Hex Bolt
3/8 x 4-1/2" Hex Bolt
5/16 x 4-1/2" Hex Bolt
5/16 x 4-1/2" Hex Bolt
Left Side of the Gym
The weld nuts
are in the normal
orientation.
Note the orientation of the weld
nuts. Tighten the bolts and
hammer the weld nuts at to
the surface so the rock climber
will t better.

Assembly
NORTHBRIDGE WITH TENT
19949-200 Rev D (03-22)
© Copyright 2016, Creative Playthings Page 13
ASSEMBLY INSTRUCTIONS
STEP 13 – Lift Upright:
With the help of others, gently lift the assembly
upright onto its legs. Move the tower to the
nal placement.
STEP 12 – Step Leg:
Slide the Step Leg (AC) into place between
the front Main Beam and the front Inside
Beam as shown. Place the angled face of the
leg ush to the front left Post and align the
holes with the holes in the Main Beam.
Fasten the Step Leg to the front Main Beam
with 3/8 x 4-1/2" Hex Bolt Assemblies.
Fasten the Leg to the Rope Base Rail as
shown, using two 5/16 x 4-1/2" Hex Bolt
Assemblies.
Front of the Gym
Front of the Gym
AC
3/8 x 4-1/2" Hex Bolt
5/16 x 4-1/2" Hex Bolt
STEP 14 – Fasten Beam to Platform Frame:
Make sure the tower is in place, solidly set into the ground.
Check to make sure the Posts are plumb and the platform is
level. Make sure the angled ends of the legs rest at against
the posts.
Fasten the each end of the Main Beams to the Platform Ends
using 3/8 x 8" Lag Screws and 3/8" Flat Washers.
Tighten all fasteners securing the
Beams to the Posts
3/8 x 8" Lag Screw
Right side of the
Gym

© Copyright 2016, Creative Playthings
NORTHBRIDGE WITH TENT
19949-200 Rev D (03-22) Page 14
ASSEMBLY INSTRUCTIONS
STEP 17 – Rung Support:
Slide the holes in the Rung Support (P) over the ends of the
Rung Assemblies.
Fasten the top of the Rung Support to the Ladder Platform
End using one 5/16 x 3" Hex Bolt Assembly.
Fasten the bottom of the Rung Support to the Rock Base
Rail using one 5/16 x 5" Hex Bolt Assembly.
Important Note: Reverse the Hex Bolt Assembly
so the Weld Nut is on the outside of the gym.
Tighten and hammer the weld nut at to ease
installation of the rock wall
STEP 16 – Rungs:
Place one Rung Collar (Z) over each end of all ve Rungs
(Y). Insert the Rung Assemblies into the holes in the Rung
Leg.
Back of
the Gym
STEP 15 – Legs to Posts:
Use a 5/16" diameter drill to bore pilot holes into the
Posts where the holes in the legs meet the posts. Fasten
the Legs to the Posts using 3/8 x 5-1/2" Lag Screws and 3/8"
Flat Washers.
Z
Y
3/8 x 5-1/2" Lag Screw
P
Back of the Gym
5/16 x 3" Hex Bolt
5/16 x 4-1/2" Hex Bolt
Front of the Gym
Right side of the
Gym
Note: Due to slight varia-
tions in angle, it may be
difcult to make the fastener
connections shown here. It is
allowable to increase the diameter of
the bolt holes involved in this step.

Assembly
NORTHBRIDGE WITH TENT
19949-200 Rev D (03-22)
© Copyright 2016, Creative Playthings Page 15
ASSEMBLY INSTRUCTIONS
Front of
the Gym
Back of
the Gym
Back of
the Gym
Front of
the Gym
STEP 18 – Secure Rungs:
Secure the Rungs using #10 x 2-1/2" Self-Drilling Screws
through the pre-drilled holes from below. Drill the Screws up
through the steel pipe until the head of the screw is ush with
the surface of the wood.
Aim the screw toward the center of the pipe and press rm-
ly while sinking the screw. If you have difculty getting the
screw to pierce the rung, use a 1/8" drill to create a hole for
the screw.
STEP 19 – Step Support:
Fasten the top of the Step Support (O) to the Rope Platform
End using one 5/16 x 3" Hex Bolt Assembly.
Fasten the bottom of the Step Support to the Rope Base Rail
using one 5/16 x 4-1/2" Hex Bolt Assembly.
Leave the fasteners very loose to ease insertion of the Steps.
O
C
Lower corner of
step ush with rail.
5/16 x 3" Hex Bolt
#10 x 4-1/2" Screw
#10 x 2-1/2" Screw
STEP 20 – Steps:
Slide the Ladder Steps (C) into the Slots in the Step Support
and the Step Leg. Make the bottom front edge of each Step
even with the face of the Step Support and Step Leg.
Fasten the Steps to the Step Support using two #10 x 2-1/2"
Screws each. Fasten the Steps to the Step Leg using two
#10 x 4-1/2" Screws each.
Tighten the fasteners connecting the Step Support to the
Platform End and Base Rail.
#10 x 2-1/2" Self-
Drilling Screw
Note: Due to slight variations in angle, it may
be difcult to make the fastener connections
shown here. It is allowable to increase the
diameter of the holes involved in this step.
This view is from
the back left corner
of the tower 5/16 x 4-1/2" Hex Bolt

© Copyright 2016, Creative Playthings
NORTHBRIDGE WITH TENT
19949-200 Rev D (03-22) Page 16
ASSEMBLY INSTRUCTIONS
STEP 23 – Platform Boards:
Lay the Deck Boards (D) and Center Deck Board (E) across
the Stringers and Inside Beams in the pattern shown at
right. Push the outer-most Deck Boards tight against the
Posts. Space the other Boards evenly between the outer-
most Boards. Make sure the holes in the Center Deck Board
align with the holes in the Swivel Stringer. Secure the Boards
using #10 x 1-5/8" Screws in each small hole. Do not use
screws in the larger holes in the Center Deck Board.
Place one End Deck Board (F) so it overhangs the Stair
Platform End by 1/4". Evenly space another End Deck
Board between the rst and the adjacent Deck Board. Se-
cure the End Deck Boards using #10 x 1-5/8" Screws in each
small hole.
Repeat with the remaining End Deck Boards at the other
end of the platform, overhanging the Ladder Platform End
1/4".
STEP 21 – Side Supports:
Loosely fasten one Side Support (AE) to the
Rock Base Rail using one 5/16 x 3" Hex Bolt
Assembly through one hole.
Swing the Side Support to rest against the
side of the Leg. Mark and drill a 1/4" diameter
pilot hole into the Leg.
Add another 5/16 x 3" Hex Bolt Assembly to
the Side Support and Base Rail. Use a 5/16 x
3-1/2" Lag Screw with a 5/16" Flat Washer to
secure the Side Support to the Leg. Tighten
all fasteners.
Repeat with the other Side Support on the
other side of the gym.
STEP 22 – Stringers:
Fasten the Stringer (AF) to each Platform End in the position
shown using one 5/16 x 4" Lag Screw and Flat Washer in
each end. The wide surface of the Stringer should be ush
with the top of the Platform Ends.
Fasten the Swivel Stringer (AG) to each Platform End in
the position shown using one 5/16 x 4" Lag Screw and Flat
Washer in each end. The wide surface of the Stringer should
be ush with the top of the Platform Ends.
AF
AG
E DD DD DD DD FF FF
Front of
the Gym
Parts omitted
for clarity.
1/4" Overhang
5/16 x 4" Lag Screw
AE
5/16 x 3-1/2" Lag Screw
5/16 x 3" Hex Bolt

Assembly
NORTHBRIDGE WITH TENT
19949-200 Rev D (03-22)
© Copyright 2016, Creative Playthings Page 17
ASSEMBLY INSTRUCTIONS
STEP 24 – Climber Boards:
Sort the Rock Boards (J). Find the best surface of each and
lay it face down. Note how the larger holes are positioned.
Align the boards so three have the holes closer to the left and
three closer to the right. Tap 1/4" weld nuts into the pairs of
larger holes on each rock board. Flip the boards so the weld
nuts face down.
Align the top edge of a Rock Board with the top edge of the
Rung Support. Secure the Rock Board to the Rung Support
and front right Leg using four #10 x 2-1/2" T25 Screws. Use
1/8" diameter pilot holes to ensure the screws do not split
the Rung Support and Leg.
Align the bottom edge of the Rope Board (K) with the bottom
edge of the Rung Support and Leg. Make sure the Large hole
in the Rope Board is aligned closest to the ground. Secure
the Rope Board to the Rung Support and front right Leg
using four #10 x 2-1/2" T25 Screws. Use 1/8" diameter pilot
holes to ensure the screws do not split the Rung Support
and Leg.
Place the four Spacer Boards (L), Narrow Spacer (U), and
remaining ve Rock Boards as shown at right. Secure the
Spacer and Rock Boards spaced evenly between the top
Rock Board and Rope Board using four #10 x 2-1/2" T25
Screws. Use 1/8" diameter pilot holes to ensure the screws
do not split the Rung Support and Leg. The gap between
boards will be approximately 3/8".
STEP 25 – Rocks:
Fasten a Climbing Rock (V) to each pair of holes in the Rock
Boards. Use 1/4 x 1-1/2" Hex Bolts, 1/4" Lock Washers, 8mm
Flat Washers and 1/4" Weld Nuts. Do not over-tighten the
fasteners. The bolt must seat completely into the Climbing
Rock, and not protrude more than a 1/8" past the end of the
weld nut. Protruding bolts can be a hazard to users, replace
any protruding bolts.
V
K
U
L
J
Typical gap: 3/8"
1/4 x 1-1/2" Hex Bolt
#10 x 2" Screw
STEP 26 – Hand Grips:
Place one Hand Grip (I) at against the outside face of the front
right Post as shown. The bottom hole of the Hand Grip should
be approximately 1-1/2" above the top of the angled Leg.
With the Hand Grip centered on the face of the Post, mark the
positions of the holes in the Hand Grip. Drill 1/8" diameter pilot
holes 1" deep at the marks. Fasten the Hand Grip using two
1/4" x 1-1/2" Lag Screws and two 8mm Flat Washers.
Place one Hand Grip at against the outside face of the back
right Leg as shown. The top hole of the Hand Grip should be
approximately 5-1/2" below the top of the angled Leg.
With the Hand Grip centered on the surface of the Leg, mark
the positions of the holes in the Grip. Drill and fasten the Hand
Grip as above.
Repeat with the remaining Grips on the other end of the gym on
the front left Post and back left Leg.
I
1/4 x 1-1/2"
Lag Screw
1-1/2"
5-1/2"
Insert Weld Nuts before
installing Rock boards.
#10 x 2-1/2" T25 Screws

© Copyright 2016, Creative Playthings
NORTHBRIDGE WITH TENT
19949-200 Rev D (03-22) Page 18
ASSEMBLY INSTRUCTIONS
STEP 28 – End Tent Pipes & Tent:
Slide one tent Pipe (AL) through the hem at
one end of the Tent (AM).
Loosen the fasteners that secure the left
end of the Front Tent Support. Fit one end
of the Tent Pipe into the large hole in the
back End Tent Support. Fit the other end of
the Pipe into the hole in the front End Tent
Support. Retighten the fasteners.
Drape the Tent over the center Tent Pipe.
Slide the nal Tent Pipe through the hem at
the other end of the Tent.
Loosen the fasteners that secure the right
end of the Front Tent Support. Fit one end
of the Tent Pipe into the large hole
in the back End Tent Sup-
port. Fit the other end of
the Pipe into the hole in
the front End Tent Sup-
port. Retighten the fasteners.
Straighten the Tent.
Use a 1/8" diameter drill to bore a pilot hole
up through the bottom of a End Tent Sup-
port and one wall of the steel Tent Pipe, as
shown. Secure the Tent Pipe to the End
Tent Support using one #10 x 2-1/2" Screw.
Repeat with the three other ends of the Tent
Pipes.
Drill a 1/8" diameter pilot hole through one
side of a Tent Post and one wall of the
center Tent Pipe. Secure the Tent Pipe
to the Tent Post using one #10 x
1-5/8" Screw. Repeat with the other
Tent Post.
STEP 27 – Tent Posts & Center Pipe:
Fasten one Tent Post Assembly (AK) to the back End
Tent Support using two 5/16 x 3" Hex Bolt Assemblies, as
shown. Make sure Weld Nuts are used on the outside
of the gym as Bolt heads can interfere with the Swing
Beam in a later step.
Slide one Tent Pipe (AL) into the large hole at the top of
the Tent Post Assembly. Slide the Other Tent Post Assem-
bly over the opposite end of the pipe.
Fasten the Tent Post Assembly to the front End Tent Sup-
AK
AM
AL
port using two 5/16 x 3" Hex Bolt Assem-
blies. Make sure each Tent Post is plumb
before tightening the fasteners.
Use Weld Nuts on
the back of the gym
5/16 x 3" Hex Bolt
#10 x 1-5/8"
Screw
#10 x 2-1/2" Screw

Assembly
NORTHBRIDGE WITH TENT
19949-200 Rev D (03-22)
© Copyright 2016, Creative Playthings Page 19
ASSEMBLY INSTRUCTIONS
STEP 31 – Climbing Rope:
The Climbing Rope Assembly comes pre-knotted on approxi-
mately 12" centers. This is done to prevent the rope from sep-
arating and it provides a better grip. DO NOT MODIFY THE
DESIGN OF THIS ROPE. IF THE ROPE IS REPLACED, IT
IS EXTREMELY IMPORTANT THAT YOU MAINTAIN THE
SAME DESIGN AND CONSTRUCTION.
Insert the Climbing Rope (W) though the hole in the Upper
Rope Support. Tie a gure eight knot at the end of the rope,
inside the gym. Leave at least 2" of rope beyond the end of
the knot.
Pre-stretch the rope before tieing the bottom end. The bot-
tom end of the Rope MUST pass through the hole in the
Rope Board and Rock Base Rail. Pull the Rope through the
hole until it is tight and tie a knot in the end. A gure-eight
knot is preferred, but an overhand knot can be used in the
lower position. Overhand
Knot
Figure 8
Knot W
Check the rope periodically to ensure that it has not loos-
ened. Tighten the rope when necessary.
WARNING: AT NO TIME SHOULD THE BOTTOM END OF
THE ROPE BE UNTIED OR LOOSE ENOUGH TO FORM
A LOOP. THIS PRESENTS EXTREME DANGER TO YOUR
CHILDREN.
STEP 29 – Swing Mount & Swing Beam:
Find the center of the Main Beam on the back of the tower. (The Bolts securing the Center Block are at the center of the Main
Beam). Mark the Main Beam 3" from the center of the Beam and 1-1/2" from the top edge of the Beam. Drill a 3/8" diameter
hole through the Main Beam at the mark.
Find the Swing Mount in the Classic Pine Swing Beam box.(See below right for an illustration of the part). Hold the Swing
Mount against the Back of the Main Beam and End Support/End Tent Support. Align the hole near the bottom with the newly
drilled hole in the Main Beam. Use a level to make sure the Swing Mount is plumb.
3"
1-1/2"
Center line of
Main Beam
Outline of
Swing Mount
Back of tented gym is
shown; wood roof gym
is similar.
End Tent Support
Main Beam
Mark the position of the up-
per hole on the End Tent
Support. Drill a 3/8" diam-
eter hole through the board
at the mark.
Fasten the Swing Mount to
the Main Beam and End Tent
Support using two 5/16 x
4-1/2" Hex Bolt Assemblies
as shown at right.
5/16 x 4-1/2" Hex Bolt
Install the Swing Beam as
instructed by the assembly
guide included with the Beam.
Swing Mount

© Copyright 2016, Creative Playthings
NORTHBRIDGE WITH TENT
19949-200 Rev D (03-22) Page 20
ASSEMBLY INSTRUCTIONS
STEP 33 – Tire Swivel & Tire Swing:
The Tire Swivel can be found in the Tire Swing box. Fasten
the Tire Swivel to the Bottom of the Swivel Stringer using
four 5/16 x 2-1/2" Hex Bolt Assemblies through the Swivel
Stringer and Center Deck Board as shown. Be sure to use
Weld Nuts at the top, set into the Center Deck Board.
Locate the Tire Swing Assembly (AT) and place it be-
neath the Gym Platform. Make sure that the hard-
ware is fastened rmly to the Tire and that the
chains are not tangled.
Using the included quick-links, fasten each chain
to the Tire Swivel, as shown. The height of the
Tire Swing should be adjusted by putting the
quick-link through a lower link in the chain. The
standard installation is to loop the quick links to
the third link from the End of the Chain.
Tighten the quick-links using a C-wrench.
STEP 32 – Ladder Slat:
Place the Ladder Slat (A) against the underside of the Rung
Leg and Rung Support. The top of the Ladder Slat should be
up against the bottom of the Platform End.
Secure the Ladder Slat using four #10 x 1-5/8" Screws.
A
AH
STEP 34 – Cargo Net:
Fasten the Cargo Net (AH) to the Stair Platform End by pass-
ing the end of each rope through a hole and tying a gure
eight or overhand knot. Approximately 1" of rope should ex-
tend beyond the knot when fully tightened. Pull down on the
cargo net to tighten the knots.
Fasten the bottom of the Cargo Net to the Rope Base Rail by
passing the end of each rope through a hole and tying a knot.
At least 1" of rope should extend beyond the knot.
It is important that the Cargo Net is as taut as possible. Peri-
odically check the knots are secure.
Be sure there is a space of at least 9" between the top
horizontal rope and the bottom of the Stair Platform End.
Deck Boards shown cut-
away for clarity. Do not
cut Deck Boards when
assembling
Use the 3rd link
on each chain.
Overhand
Knot
Figure 8
Knot
≥ 9"
#10 x 1-5/8"
Screw
5/16 x 2-1/2"
Hex Bolt