Creative Playthings Playtime PS10CLASB User manual

MODEL PS10CLASB & PTCLASB
ASSEMBLY MANUAL
If you have problems or questions about your Creative Playthings Play Set,
DO NOT CALL THE RETAILER.
Contact Creative Playthings Customer Service at 1-800-598-4997 or
[email protected]
Please read the owner’s manual before assem-
bling your Play Set, it provides additional
information on the care and use of your Play
Set.
You must carefully read the entire instruction
manual before proceeding with the assembly
or use of your new Play Set.
Creative Playthings takes great care to design
its products with your child’s safety in mind.
However, only with careful supervision
and proper safety instructions, can you be
assured of safe play time on any product
designed for children.
By
This product is intended for single
family home/residential use only and
not intended for use in any public
setting. Placement in any public
setting constitutes a misuse of this
product.
All hardware on this set is specially coated
for corrosion resistance.
If non-Creative Playthings hardware is used,
it must be galvanized or stainless steel.
™
The swing accessories provided with your set
may be different than those shown above.

Assembly
© Copyright 2010, Creative Playthings. Printed in U.S.A.
MODEL PS10CLASB & PTCLASB
19771-100 Rev H (05-20) Page 2
PLAY SET SAFETY
Observing the following statements & warnings reduces the likelihood of serious or fatal injury:
• Children should use equipment only in its intended manner.
• Children should not wear loose or stringed clothing while using playground equipment.
• Children should not play on equipment in wet weather conditions due to potentially slippery surfaces.
• Children should NOT walk too closely in front of, behind, or between moving swings and trapezes.
• Children should NOT swing empty swing seats.
• Children should NOT jump off swings and/or trapeze while they are in motion.
• Children should NOT twist swing ropes or chains because this will reduce the strength of the ropes, connectors & chains.
• Children should sit in the center of the swings with their full weight on the seats.
• Children should NOT be on the top surface of the swing beam.
• Children should NOT use the equipment in a manner other than intended.
• Children should NOT get off the equipment while it is in motion.
• On-site adult supervision is required at all times for children of all ages.
• Until assembly is complete, DO NOT let your children use the Play Set.
• Never fasten anything not approved by Creative Playthings to your Play Set. Accessories or items not ap-
proved by Creative Playthings include; Dog runs, clothes lines, electrical devices, or bird feeders etc.
• Suspended ropes, chains, and cables must be secured at both ends.
• Suspended ropes, chains, and cables must not be capable of looping back on themselves.
• Do not allow more than 120 lbs. on Single occupancy swing accessories such as the Sling Swing and Trapeze.
• Do NOT allow more than 175 lbs. on multiple use swing accessories such as the Back-to-Back Plastic Glider.
• Do NOT allow more children on the Play Set than can simultaneously use all the swing stations at one time.
• Children MUST NEVER wear bicycle helmets while playing on the play-set.
Assembly Safety:
• Adult assembly required
• Face slide away from the sun.
• Keep the work area clean and clear of obstructions.
• Children should stay out of the work area until the safe play area is cleared of obstacles, the Play Set has been
completely assembled, all hardware has been tightened and checked, and all tools have been picked up.
• Keep children off the Play Set until it has been completely assembled.
• Parts of the assembly process may require help from another competent adult.
• Do not stand on the platform until the Play Set has been completely assembled, use a step ladder if you can
not reach high enough.
• Follow the manufacturers' safety recommendations for the tools and equipment you use.
• Avoid assembling your Play Set in poor weather conditions.
• Wear proper clothing and safety equipment (safety glasses, boots, and gloves) while assembling your Play Set.
FOR SAFETY SAKE, PLEASE TAKE TIME TO READ ALL INSTRUCTIONS COMPLETELY AND
CAUTION YOUR CHILDREN APPROPRIATELY.

Assembly
MODEL PS10CLASB & PTCLASB
19771-100 Rev H (05-20)
© Copyright 2010, Creative Playthings. Printed in U.S.A. Page 3
SAFE PLAY AREA
SELECTING THE CORRECT LOCATION FOR YOUR PLAY PRODUCT IS IMPORTANT FOR
YOUR CHILDREN’S SAFETY AND THE PRODUCT’S LONGEVITY.
Play Set Dimensions:
• The MODELS PS10CLASB and PTCLASB Swing Sets have ground dimensions of 9'-0" x 10'-0".
• The Swing Set requires a level ground surface of 21'-0" x 28'-3' for a Safe Play Area
• Additional accessories may increase the size of the Safe Play Area.
• The maximum fall height for your Swing Set is 87" as measured from the top of the Top Ladder.
Safe Play Area:
• The Safe Play Area refers to a zone extending 6' (2 meters) beyond the Play Set on all sides, including the slide
and the space above the Play Set. Because children may deliberately jump from a moving swing, the Safe Play
Area must be extended to 14' (4.27 meters) in front of and behind a swinging Accessory.
• The ground surface must be level. Installing your Play Set on sloping ground can cause it to lean or “rack”.
This leaning puts additional stress on all connections and joints and in time will cause those connections to
loosen and fail.
• The Safe Play Area must be free of all structures, landscaping, trees and branches, rocks, wires, and other
obstacles to safe play. Children can be seriously injured running, or swinging into these obstacles.
• Remove all tripping hazards from the Safe Play Area. Tripping hazards include; roots, stumps, rocks, landscap-
ing, sprinkler heads, railroad ties, plumbing and electrical connections.
• Do not install your Play Set over concrete, gravel, asphalt, packed earth, or any other hard surface. The follow-
ing is a list of recommended ground covers from the Consumer Product Safety Commission.
RECOMMENDED GROUND COVER
Suggested Material Uncompressed Depth
Double Shredded Bark Mulch 9"
Uniform Wood Chips 12"
Fine Gravel 12"
Fine Sand 12"
• Any edging used to contain the ground cover must be beyond the Safe Play Area. (i.e.. Landscape Timbers)
A FALL ONTO A HARD SURFACE COULD RESULT IN SERIOUS
INJURY.
Safe play area using
recommended ground cover.
Landscape Timbers 6' from
play structure.
6'
(2 M)
6'
(2 M)
14'
(4.27 M)
14'
(4.27 M)

Assembly
© Copyright 2010, Creative Playthings. Printed in U.S.A.
MODEL PS10CLASB & PTCLASB
19771-100 Rev H (05-20) Page 4
COMPONENTS
A
B
H
D
F
G
C
J
I
60057-101 Playtime Classic Swing Beam
A 2 32797-102 Swing Beam Leg Brace 2 x 4 x 71"
B 4 33123-102 Swing Beam Leg 4 x 4 x 102-3/8"
C 1 40517-102 Classic Beam Assembly
50465-100 Accessories, Playtime Classic Swing Beam
D 4 14022-101 Safe-T-Connect Bracket, Right
E 4 14022-201 Safe-T-Connect Bracket, Left
F 5 36515-102 Ground Stake
1/4" Lock
Washer
1/4" Flat
Washer
5/16" Flat
Washer
5/16" Lock
Nut
1/4" Weld
Nut
#6 x 1/2" Pan
Head Screw
#10 x 2-1/2" Screw
1/4 x 4-1/2" Hex Bolt
5/16 x 4" Hex Bolt
5/16 x 3-1/2" Hex Bolt
1/4 x 3" Hex Bolt
1 50105-700 NyGlide Swing Hanger 6 Pack
6 12002-206 Flat Washer 5/16"
G 6 17004-100 NyGlide Swing Hanger, Screw Type
1 50465-701 1/4" Hardware Bag
22 12002-205 Flat Washer 1/4"
14 12017-205 Lock Washer 1/4"
13 17001-104 Weld Nut-Long Barrel 1/4
8 17003-1209 Hex Bolt 1/4 x 3"
4 17003-1809 Hex Bolt 1/4 x 4-1/2"
10 17020-113 Screw #10 x 2-1/2"
1 50465-702 5/16" Hardware Bag
48 12002-206 Flat Washer 5/16"
8 17003-1411 Hex Bolt 5/16-18 x 3-1/2"
16 17003-1611 Hex Bolt 5/16-18 x 4"
25 12052-106 Lock Nut 5/16"
1 50469-100 Playtime Name Plate Bag
H 1 14208-100 Playtime Name Plate
4 17128-202 Stainless Pan Head Screw #6 x 1/2"
Swing Options:
1 50453-400 2 Swing 1 Trap Acc Pack, Rope
I 2 40009-400 Sling Swing, Green w/Rope
J 1 40381-100 Plastic Ring Trap. Combo, Yellow
(or 40535-100 Ring Trapeze Assembly w/Rope)
OR
1 AA934-204 2 Swing 1 Trap Pack, Vinyl Chain
2 40321-400 Sling Swing, Vinyl Coated Chain
1 40311-402 Ring Trapeze, Vinyl Coated Chain

Assembly
MODEL PS10CLASB & PTCLASB
19771-100 Rev H (05-20)
© Copyright 2010, Creative Playthings. Printed in U.S.A. Page 5
MAINTENANCE INSTRUCTIONS
Re-staining Information: (Your Play Set is stained at our factory. No stain is needed at initial assembly.)
• Pigmented, exterior, water repellent stains are recommended and will provide an excellent barrier against moisture
without hiding the natural wood grain or leaving a lm that may later crack or peel.
• We recommend that you apply stain according to the instructions and precautions provided by the stain manufacturer.
• It should take one or more quarts to cover your set.
• Contact your local dealer or call Creative Playthings for our staining products.
• Do not paint, or varnish rungs or steps.
• Avoid using nishes that create slippery surfaces.
Maintenance:
• Wooden playground equipment will last for years with proper maintenance. Maintenance of the Play Set nish will
vary depending on weather climate.
• As a safety precaution, check all hardware, such as nuts and bolts, for tightness twice a month during use and at the
beginning of each play season. Tighten as required and specied in these instructions. Do not over-tighten.
• Check structure twice monthly during usage for any evidence of deterioration. If upon inspection, hardware has sharp edges,
rusted or structural pieces have signs of premature failure; replace them through Creative Playthings Customer Service.
• Oil all metallic moving parts monthly during the usage season.
• The swings, trapeze, tent, rope ladders, and any other removable plastic accessories should be removed and taken
indoors when outside temperatures drop below 32° F (0° C).
• Wood will expand and contract as it adjusts to temperature changes and varying moisture conditions. Checks or cracks
are a natural characteristic of all wood and will not affect the strength or durability of the wooden components.
• To maintain the nish of your set, a light sanding and an application of an exterior stain will repair scratches and prevent
wood from aging prematurely.
• The wood parts of your Play Set should never be disposed of by burning.
• Dispose of all parts so as not to create a hazard.
• "Check all coverings for bolts and sharp edges and replace when required."
• "Check swing seats, chains, ropes, and other means of of attachments for evidence of deterioration". Replace through
Creative Playthings Customer Service.
Tools & Materials Suggested for Assembly:
• Claw Hammer
• Carpenter’s Level
• Box Wrench or Sockets (7/16" & 1/2")
• Driver Drill (Medium Phillips)
• Locking Pliers
• 10 ft. Tape Measure
• 6 ft. Step Ladder
• Beeswax or Soap (Used to lubricate screw threads)
Hex Bolt & Weld Nut Assembly:
Align the holes in the parts to be fas-
tened. Start preliminary tightening of
bolt into weld nut by hand. Tighten each
bolt with a wrench until the lock washer
is fully compressed between the head
of the bolt and the at washer.
Correct Assembly:
Bolt has been screwed securely into
weld nut and the connection is tight.
Check connections periodically for
tightness during the life of the Play Set
. Do not over tighten.
Incorrect Assembly:
During assembly or maintenance the bolt
protrudes 1/8" past the weld nut. Call cus-
tomer service or replace the bolt at a local
hardware store. You may be overtighten-
ing or using the wrong size bolt. Failure
to replace this bolt with a shorter one
could result in serious injury.

Assembly
© Copyright 2010, Creative Playthings. Printed in U.S.A.
MODEL PS10CLASB & PTCLASB
19771-100 Rev H (05-20) Page 6
ASSEMBLY INSTRUCTIONS
STEP 1 – Secure Beam Assembly:
Lay out the Swing Beam in the play area. The holes for the
swing connectors should face upward.
Secure the two rails of the Beam Assembly (C) using eight
1/4" x 3" Hex bolts, 1/4" Lock Washers, 1/4" Flat Washers
and 1/4" Weld Nuts, as shown.
ASSEMBLY INSTRUCTIONS
STEP 3 – Safe-T-Connect Brackets:
Fasten one Left Hand Safe-T-Connect Bracket (E) and one
Right Hand Safe-T-Connect Bracket (D) to each Leg (B) as
shown. Use four 5/16 x 4" Hex Bolts with Flat Washers and
four NyLock Nuts for each leg.
The Flat Washers are used to make sure that the tips of
the bolts do not extend too far beyond the nuts. If the bolts
do not extend through the nut when tightened, the washers
should be omitted.
Leave the fasteners loose until the legs are fastened to the
Beam.
STEP 2 – NyGlide Swing Connectors:
Insert the screw end of a NyGlide Swing Hanger through
a 5/16" at washer and into one of the holes in the bottom
of the Beam. Use a screwdriver for leverage while turning
the NyGlide into the wood. The connector must be screwed
into the wood fully, with the bend of the shaft resting rmly
against the 5/16" at washer. Repeat with the other NyGlide
Swing Hangers.
It is extremely important that you align each NyGlide Swing
Connector in the proper position as shown in the illustration.
The swing motion must be perpendicular to the Beam.
CAUTION: If these installation instructions are not explicitly
followed, the NyGlide shaft will break or pull out of the wood
and injuries will result.
ED
B
C

Assembly
MODEL PS10CLASB & PTCLASB
19771-100 Rev H (05-20)
© Copyright 2010, Creative Playthings. Printed in U.S.A. Page 7
ASSEMBLY INSTRUCTIONS
STEP 4 – Legs to Beam:
An assistant is recommended for attaching the Legs to the
Beam.
Prop up one end of the Beam Assembly (C); the Swing Beam
Leg Brace (A) can be used.
Fasten two Legs (B) to the Beam Assembly using four 5/16 x
3-1/2" Hex Bolts with Flat Washers and four NyLock Nuts.
Leave fasteners loose until after installing the Swing Beam
Leg Brace.
STEP 5 – Leg Brace:
Fasten the Swing Beam Leg Brace (A) to the two Legs using
two 1/4 x 4-1/2" Hex Bolt Assemblies*, as shown.
Tighten all fasteners on the Beam and Leg Assembly.
* A Hex Bolt Assembly consists of one Hex Bolt, one Lock
Washer, one Flat Washer, and one Weld Nut.
C
A
A
B
STEP 6 – Repeat at Other End:
Repeat the last two steps with the remaining
Legs and Leg Brace at the other end of the
Beam.

Assembly
© Copyright 2010, Creative Playthings. Printed in U.S.A.
MODEL PS10CLASB & PTCLASB
19771-100 Rev H (05-20) Page 8
ASSEMBLY INSTRUCTIONS
STEP 7 – Flip Assembly:
Flip the complete Assembly so that it stands on the legs.
Move the Assembly into the place where it will be used.
STEP 8 – Name Plate:
It is important to fasten the Playtime name plate to the Swing
Beam. Federal safety regulations require that the name of
the manufacturer be permanently fastened to the gym, for
identication in case of warranty claim.
Center the name plate between the hex bolts near the mid-
dle of the Beam Assembly. Use the included #6 x 1/2" pan
head screws to attach the name plate to the Beam. Make
sure that the screws are slightly loose. This will keep the
nameplate from bending due to temperature and moisture
changes in the wood.
STEP 9 – Ground Stakes:
Hammer Ground Stakes (F) into the ground at the ends
of each Leg (B). Secure each stake with two #10 x 2-1/2"
Screws through the pre-drilled holes.
Note: Do NOT use concrete to set Ground Stakes. Pound a
metal spike or rod into the ground to start a hole in hard or
rocky ground.
47" to end of Beam
47" to end of Beam
Center Line
STEP 10 – Hang Swings:
Hang the Swings from the NyGlide Swing Hangers.
U.S. safety standards require a minimum clearance of 8"
from the bottom of each Swing Accessory to the ground.
U.K. (& E.U.) safety standards require a minimum clearance
of 350mm (13-3/4") between the bottom of each Swing Ac-
cessory and the ground.
The height of each Swing Accessory is adjusted by using a
different link in the chain. Be sure to hang the Swings Ac-
cessories with ground clearance greater than or equal to the
safety standard for your region.
F