Creative Playthings Lexington Premium Pack 18 User manual

LEXINGTON PREMIUM PACK 18
LEXI9WPP18-100 Rev C (05-20)
© Copyright 2018, Creative Playthings
CHILDHOOD STARTS HERE
LEXI9WPP18
L P P 
• Start by assembling the Lexington tower. Instructions and hard-
ware are in the cartons noted at left. The gym is rotated 90° from
the position shown in the instructions.
The components of this gym can be combined with others to
create different play sets. This is the best order of assembly
to create this specic set.
Read this sheet and all instructions included with the
different parts before assembly.
See the Instructions and Owner's Manual included in carton
63007-445 for important safety information.
Dimensions of assembled package:
24' 4" wide x 20' 7" deep x 12' 9" tall
Cartons for this Play Set:
1 63007-421 Lexington Gym 1 (Hardware)
1 63007-422 Lexington Gym 2
1 63007-423 Lexington Gym 3
1 63007-445 Lexington Roof (Hdwre & Instr)
1 SH946-102 Access Ladder, 5ft
1 AG942-400 Access Ladder Handles (Hdwre & Instr)
1 63058-202 4 Position Swing Beam
1 63060-222 9ft Swing Beam Legs (Hdwre & Instr)
1 50546-777 3 Swings, 1 Trapeze
1 SM964-402 Gable Fans (Hdwre & Instr)
2 SM963-402 Dormer (Hdwre & Instr)
1 SH922-800Q Ramp (Hdwre & Instr)
1 AH201-102Q Rock Climbing Wall (Hdwre & Instr)
1 63081-102 Ice Cream Stand (Hdwre & Instr)
1 SC910-800Q Lexington Play Floor (Hdwre & Instr)
63008-221 Skybox 1 (Hdwre & Instr)
1 63008-222 Skybox 2
1 SJ926-810 Skybox Wood Roof (Hdwre & Instr)
1 SC904-800Q Skybox Play Floor (Hdwre & Instr)
1 15140-400 14ft Swoosh Slide
1 50398-700 Swoosh Skybox Kit (Hdwre & Instr)
1 8400-202 Spiral Slide, Green (Hardware)
1 63033-102 Spiral Mount (Hdwre & Instr)
2 40456-402 End Panel
1 40459-402 Double Window Panel
1 40460-402 Door & Window Panel (Hardware)
1 63073-101 Clubhouse Window Pk (Hdwre & Instr)
1 AP970-104 Bubble Panel (Hdwre & Instr)
1 AG943-400 Slide Handle (Hdwre & Instr)
15 1/2"
7 1/4"
3"
0"
• Wait to install the Access Ladder, Slide, and
Wall Slats until after the rest of the play set is
complete.
• Lex step 2. Omit the sandbox end from the end
of the gym adjacent to the Skybox. It will be
altered to t the Skybox and play oors.
• Lex step 7. Do not install the safety rail.
• Lex step 8. Do not install the angle braces.
• Lex step 14. Do not install the end wall support
on the Skybox end of the tower.
• Lex step 15. The swing mount isn't needed.
• Lex step 25. Before installing the roof, nd the
post where the swing beam will mount. Drill
7/16" diameter holes through the post at 3",
7-1/4" and 15-1/2" below the top of the post as
Dormers
shown at right.The beam will be mounted to the front of the post
using these holes. Insert one 5/16" weld nut into the top hole on
the inside face of the post. Be sure the threads on the weld nut are
clear, it will be captured by the roof support. Install the roof.
• Mount the Swing Beam using instructions and hardware included
in 63060-222. Mount the beam to the previously drilled holes at
right rather than the way shown in the instructions. You may need
to temporarily disconnect the roof from the post to put the beam in
place.

© Copyright 2018, Creative Playthings
LEXINGTON PREMIUM PACK 18
LEXI9WPP18-100 Rev C (05-20) Page 2
• Once the roof, roof supports, ridge cap and swing beam
are installed, proceed with the Skybox tower.
• Skybox step 2. Alter the Lex sandbox end and the skybox
sandbox sides as shown on page 5 of the skybox Play
Floor instructions found in SC904-800Q.
• Skybox step 11. Use the front posts from The Skybox Roof
(SJ926-810) in place of the post extensions.
• Skybox Step 17. Wait to install the wall slats until after
installing the bubble and slides.
• Skybox Step 21 & 22. Install the slats in reverse orienta-
tion so the opening is on the opposite side. Install the lad-
der aligned with the opening.
• Install the Skybox Wood Roof (SJ926-810).
• Install the Skybox Play Floor (SC904-800Q) using the
method found in the Skybox Play Floor instructions on
Page 6. Some parts of the Skybox Play Floor will be cut
to t. Do not install the platform boards until the after the
Lexington play oor stringers are installed.
• Install the Lexington Play Floor (SC910-800Q) and com-
plete the skybox play oor.
• Install the Clubhouse Panels (40456-402, 40459-402, &
40460-402), using the instructions and hardwarre atached
to the Door Panel.
• Install the Gable Fans (SM964-402).
• Using a ladder, install the Dormers (SM963-402) in the
positions shown on the front page of this guide. Ladder
access will be obstructed by later installations.
• Install the Ice Cream Stand (63081-102).
• Mount the 14ft Swoosh Slide (15140-400) to the front of
the Skybox using the instructions from 50398-700.
• Install the Bubble Panel (AP970-104) above the Ice Cream
Stand.
• Install the Spiral Slide using the instructions in 63033-102.
If the lower support bracket can be mounted to the adja-
cent gym corner post, do it. Otherwise use the included
support rail.
• The Rock Climber (AH201-102Q) on the back of the tower.
• Lean the Access Ladder, Wave Slide, and Ramp as shown
on the rst page of this guide. Check spacing.
• Secure the access ladder using the method shown in step
17 of the Lexington instructions.
• Fasten Access Ladder Handles (AG942-400) to the ac-
cess aadder.
• Secure the ramp.
• Install the slide mount and slide using the method shown
in steps 23 and 24 of the Lexington instructions.
• Install wall slats in the postions shown in images, using
the methods from the Lexington and Skybox instructions.
Gaps must be narrower than 3-1/2" or wider than 9" to
prevent potential head entrapment.
• Mount the hand grips to the entrance wall slats.
• Mount the Slide Handles (AG943-400) above the wave
and swoosh slides.
• Install the ower box and shutters from the Window Pack
(63073-101) on the window panel below the skybox.
• Double-check all fasteners are secure and all recessed
hardware is covered by hole caps.
Swing Beam
Bubble Panel
Gable Fan
Rock Climber
Spiral Slide Ramp
Ice
Cream
Stand