Creative Playthings 50545-555 User manual

 4 14186-400 GliderBracket
  
 8 12002-207 FlatWasher,3/8"
 4 12017-207 LockWasher,3/8"
 4 17003-1413 HexBolt,3/8x3-1/2"
 4 17003-1813 HexBolt,3/8x4-1/2"
 4 12052-107 NylockNut,3/8"
 8 12002-206 FlatWasher,5/16"
 8 17036-602 LagScrew,5/16x1-1/2"











HexBolt3/8x4-1/2"
HexBolt3/8x3-1/2"
LagScrew5/16x1-1/2"
FlatWasher3/8"
LockNut3/8"LockWasher3/8"
FlatWasher5/16"

Ifthisisanewinstallation,donotinstallthepair
of Swing Hangers closest to the Legs of the
SwingBeam.IftheSwingHangersarealready
installed,removethem.
Find the two pair of Bolts above the Swing
Hanger positions nearest the Legs. Remove
thefourHexBoltsandassociatedwashersand
weldnuts.
Seeinstructionforthegym
towhichtheSwingBeamis
mountedforspecialsafety
informationregardingrequired
space,resilientgroundcover,
etc.
ThispackageisforusewithPremiumPineand
ClassicPineswingbeams.ThePremiumPine
beamisshownintheillustrations.
GliderBrackets
RemoveBolts

 ©Copyright2014,CreativePlaythings.PrintedinU.S.A.
19919-100RevA(09-14)
GliderBracketPack


Ononesideofthebeam,alignthetopholes
of a Glider Bracket with two of the holes
where Bolts were removed in the previous
step.Markthepositionofthelowerholesof
theGliderBracketontheBeam.Dothesame
withanotherGliderBracketandtheotherpair
ofholes.
Drill 3/16" diameter holes 1-1/2" into the
Beamatthemarks.
TurntheBeamover.Markanddrillthebeam
inthesamemanner.

FastentheGlidersBracketstotheBeamAs-
sembly using two 3/8 x 4-1/2" Hex Bolts*,
four3/8FlatWashers,andtwoNylockNuts
foreachpairofBrackets,intheupperholes
asshown.Useone5/16x1-1/2"LagScrew
with one 5/16 Flat Washer for each of the
eightremaininglowerholes.
*Use3/8x3-1/2"BoltsfortheClassicPine
Beam.

HangtheBack-to-BackGliderbyhookingthe
chaininthesnaphooksontheGliderHang-
ers.Followthespecialassemblyinstructions
includedfortheBack-to-BackGlider.
U.S. safety standards require a minimum
clearance of 8" from the bottom of each
SwingAccessorytotheground.U.K.(&E.U.)
safety standards require a minimum clear-
anceof350mm(13-3/4")betweenthebottom
ofeachSwingAccessoryandtheground.
The height of each SwingAccessory is ad-
justed by using a different link in the chain.
BesuretohangtheSwingsAccessorieswith
groundclearancegreaterthanorequaltothe
safetystandardforyourregion.
Drill3/16"
Dia.Holes