Creek Company ODC CLASSIC XL User manual

ODC CLASSIC XL
TM
ASSEMBLY INSTRUCTIONS
THIS BOX CONTAINS:
STEEL FRAME
(1) Left Frame Member
(1) Right Frame Member
(1) Plastic Seat Back
(1) Plastic Seat Bottom
(4) Seat Screws
(2) Foot Bars
(1) Rear Frame Member
(1) Mesh Cargo Deck
(1) Stripping Apron
(8) Short Snap Pins
OARS & OARLOCKS
(1) Pair 6-foot 2 piece Oars
(1) Pair Clamp-on Oarlocks
(2) Oarlock Bushings
PONTOONS
(1) Left Pontoon
(1) Right Pontoon
Each Pontoon consists of Nylon Cover with PVC bottom featuring integral Side Storage Pockets,
Straps and Cam-lock Buckles to secure the Frame and Main Bladder with Pro Series Valves
PUMP
Complete with a set of Adaptors
PATCH KIT
OUTDOOR DISCOVERY CRAFTTM

ODC CLASSIC XL
TM
ASSEMBLY INSTRUCTIONS
OUTDOOR DISCOVERY CRAFTTM
I. PLASTIC SEAT ASSEMBLY
1. Assemble Seat Back to Seat Bottom using Seat Assembly Pins (see gure 1a).
II. ASSEMBLE FRAME
NOTE: Your Frame Assembles using (8) Short Snap Pins. Please follow instructions accordingly.
1. Assemble Cargo Deck by sling Mesh Cargo Deck over Frame Member (see gure 1) and secure using attached Hook and
Loop and Ladder Lock / Strap Fastners.
2. Assemble Seat to Seat Support Frame Member using (4) Seat Screws. (See Figure 1a)
3. Assemble Seat Support Frame Member to Left and Right Frame Members using (4) of the Short Snap Pins. (see gure 1)
4. Assemble Cargo Deck to Left and Right Frame Members using (2) Short Snap Pins (see gure 1).
5 Assemble Foot Bars to Left and Right Frame Members using (2) Short Snap Pins (see gures 1).
II. PONTOON INFLATION
NOTE: Use double action pumpwith adapters (included), available from the Creek Company
1. Inate each Pontoon. The Valve is located inside the Storage Pocket of each Pontoon.(see gure 3).
Inate until rm (do not over inate).
PONTOON DEFLATION: Depress center valve butoon and turn clockwise 1/4 turn to lock open. Depress and turn 1/4 turn counter
clockwise to close the valve.
III. ATTACH PONTOONS TO FRAME
NOTE: Always inate the Pontoons rst, before attaching to Frame.
1. Position inated Pontoons under the Left and Right Frame Members with ODC CLASSIC XLTM logos oriented to the
outside.The Frame Members t around the Storage Pockets.
2. Attach Pontoons to Frame as illustrated in gures 3 and 3a. Note: Be sure the Straps are pulled tight through the
Cam-lock Buckles. Frame should be positioned forward or aft on the Pontoons to achieve center of gravity for an even
ride when fully loaded on the water.
IV. OAR & OARLOCK ASSEMBLY
1. Loosen the wingnut on the Oarlock and slide the Oarlock onto the handle end of the Oar Shaft.
2. Attach blade end of Oar Handle to end of Oar.
3. Place Oarlock Shafts into Frame.
4. With the Oarlocks installed on the Frame, the oars should be equally adjusted left and right allowing at least two
thumbs’ distance between the Oars, to avoid pinching your thumbs when rowing. With the blades perpendicular to
the water, tighten the wingnuts.
V. ATTACH STRIPPING APRON TO FRAME
1. Snap front two Straps around the Frame underneath the Oarlocks, and snap the back two Straps to the Right and Left
Frame Members just behind Storage Pockets.

b
Valve inside
Storsge Pocket
e
Fig. 1
Frame assembly
a. Cargo Deck Rear Member
with Mesh Cargo Deck
(assembly required)
b. Left Frame Member
c. Right Frame Member
d. Seat Support Frame Member
e. Foot Bars
a
b
Seat
Assembly
Pins
c
Fig. 1a
Seat Frame assembly
a. Plastic Seat Back
b. Plastic Seat Bottom
c. Seat Support Member Fig. 3
Pontoon-to-Frame attachment
Frame slips over two Storage Pockets
Slide through Oarlocks and 6 1/2
foot Oars are available
for your
ODC Classix XLTM
Visit
www.CreekCompany.com
for details or call
970-879-5221x 300
Fig. 2
Detail of Snap Pin
installation
All Frame parts attach with Snap
Pins.
Your Frame assembles using
(2) Long Snap Pins and (12) Short
Snap Pins. Please follow
instructions accordingly.
Fig. 3a
Pontoon-to-frame attachment
Detail of Camlock Strap
Strap
D-Ring
Frame
d
c
HIN
HIN
Motor Mount / Anchor Drop /
Rod Holder Kit is available
for your
ODC Classix XLTM
Visit
www.CreekCompany.com
for details or call
970-879-5221x 300
a

ODC CLASSIC XL TM
OUTDOOR DISCOVERY CRAFT TM
Your ODC Outdoor Discovery CraftTM is designed to give you many years of service.
Please follow ination instructions and warnings carefully.
IF YOU EVER HAVE ANY QUESTIONS OR PROBLEMS WITH YOUR ODC CLASSIC XLTM PLEASE DO NOT RE-
TURN IT TO THE DEALER YOU BOUGHT IT FROM. PLEASE CONTACT THE CREEK COMPANY
DIRECTLY TOLL FREE AT 1-800-843-8454. WE ARE OPEN M-F 9AM-5PM MOUNTAIN TIME. OR CONTACT US VIA
E-MAIL AT [e-mail].
HIN is located on square tubing of seat support frame member and on right main frame member (See Figure 1)
Warning:
Please read and follow carefully.
1. Always wear a US Coast Guard approved personal otation device when in your ODC CLASSIC XLTM.
2. Never oat alone.
3. Always check your ODC CLASSIC XLTM Air Bladders, outer skin and stitching for possible damage before you use your craft.
4. Never use your craft if you suspect the Air Bladders, outer skin or stitching has been damaged.
5. Never overinate your ODC CLASSIC XLTM.
6. Never use your ODC CLASSIC XLTM without the Pontoons fully inated.
7. Your ODC CLASSIC XLTM is not designed for use in salt water.
CARE AND MAINTENANCE:
1. If your Pontoon Bladder is losing air, please check that Valve Assembly and Top Valve Cap are fully seated. Reseat valve
assembly and repeat pontoon ination instructions.
2. Do not store your ODC CLASSIC TM in direct sunlight.
3. If you are leaving your ODC CLASSIC XLTM out in the sun for any amount of time, be aware that the heat can increase the
pressure inside the Pontoons to a dangerous level. Let some of the air out of the pontoons if the craft will be out of the water in the
sun for any length of time, or if it is stored in a vehicle, etc.
4. A gain in altitude will increase the pressure in the Pontoons also. If you are taking your inated ODC CLASSIC XLTM from a
low elevation to a high elevation, be sure to let some of the air out of it.
5. For short term storage, we recommend you let some air out of your pontoons.
6. For long term storage, we recommend you make sure your ODC CLASSIC XLTM is completely dry, deated and stored out
of the sunlight in a cool dry area.. Do not store your wet ODC CLASSIC XLTM in freezing temperatures as this may result in
Frame and other component damage.
7. Repairing Bladder, use enclosed patch kit. Identify puncture. Fully deate Bladder. Clean and dry area around puncture. Apply
glue to puncture area and patch using applicator straw. Press patch over puncture area. Allow 24 hours to dry, before inating.
8. Note: Metal parts may rust and are not covered under warranty.
Accessories are available for your ODC CLASSIC XLTM .
Ask for them where you bought your ODC SUPERSPORT XR 1™, or visit the Creek Company Store at www.CreekCompany.com
The Creek Company Ltd. , PO Box 773892, Steamboat Springs, CO 80477
email: [email protected] • Made in China
Specications and other details subject to change without notice. All Creek Company
products are guaranteed against defects in material and workmanship for the
life of theproduct to the original owner.
This does not cover damage due to misuse or normal wear and tear.