AllSportSystems DIY Bay User manual
DIY Bay Installation Guide
1
Connector Kit:
●6 x 3-Way Connectors
●2 x 90° Connector
●3 x Couplers (only if wider than 10ft)
EMT Pole Kit (optional upgrade):
●8 x Height EMT Poles + 4 x couplers
●6 x Width EMT Poles + 3 x couplers
●4 x Depth EMT Poles
DIY Bay Parts List
Fabric Parts:
●1 x Black Fabric Wrapper
●2 x Black Pole Sleeves
●1 x Impact Screen
●4 x Screen/Foam Trim Panels
●8 x Foam Inserts (optional upgrade)
Additional Hardware:
●36 x Connector Bolts
●Ball Bungee Straps
2
Prepare Poles & Connectors
●Mark each pole 4-½” from
end.
●Insert poles 4-½” into
connectors.
●For best results, remove
eye-bolts and replace with
connector bolts for all
connectors and couplers.
3
Bay Size 10’ Poles
Needed Height Width Width
Extension Depth
8’H x 10’W x 5’D 9 QTY 4 Poles
7’-9”
QTY 3 Poles
9’-9” None needed QTY 2 Poles to
4 pieces 4’-9”
9’H x 10’W x 5’D 9 QTY 4 Poles
8’-9”
QTY 3 Poles
9’-9” None needed QTY 2 Poles to
4 pieces 4’-9”
9’H x 12’W x 5’D 10 QTY 4 Poles
8’-9”
QTY 3 Poles 10’
(no cuts)
QTY 1 pole to
3 pieces 1’9”
QTY 2 Poles to
4 pieces 4’-9”
9’H x 14’W x 5’D 11 QTY 4 Poles
8’-9”
QTY 3 Poles 10’
(no cuts)
QTY 2 poles to
3 pieces 3’9”
QTY 2 Poles to
4 pieces 4’-9”
9’H x 16’W x 5’D 12 QTY 4 Poles
8’-9”
QTY 3 Poles 10’
(no cuts)
QTY 3 poles to
3 pieces 5’9”
QTY 2 Poles to
4 pieces 4’-9”
DIY Bay 1” EMT Pole Cutting Chart
For customers who did not purchase the 1” EMT Pole Kit
4
1) BUILD
BOTTOM
2x 3-Ways
2x 90°
2x Depth poles
1x Width pole
1x Coupler + extender*
2) BUILD
REAR
2x 3-Ways
2x Height poles
1x Width pole
1x Coupler + extender*
3) BUILD
DEPTH 2x Depth poles
4) BUILD
FRONT
2x 3-Ways
2x Height poles
1x Width pole
1x Coupler + extender*
Cage assembly for EMT’s Purchased Locally
For pole count and lengths see
DIY Bay 1” EMT Pole Cutting Chart
*Couplers + extender poles only
needed for bays larger than 10ft wide.
●SkyRailPlus customers see page 8 for cage modifications.
●Insert poles 4 ½” into connectors as noted on page 3.
5
Bay Size Height Poles Width Poles Depth Poles
8’H x 10’W x 5’D QTY 8 Poles
3’-11 ½”
QTY 6 Poles
4’-10 ½”
QTY 4 Poles
4’-9”
9’H x 10’W x 5’D QTY 8 Poles
4’-4 ½”
QTY 6 Poles
4’-10 ½”
QTY 4 Poles
4’-9”
9’H x 12’W x 5’D QTY 8 Poles
4’-4 ½”
QTY 6 Poles
5’-10 ½”
QTY 4 Poles
4’-9”
9’H x 14’W x 5’D QTY 8 Poles
4’-4 ½”
QTY 6 Poles
6’-10 ½”
QTY 4 Poles
4’-9”
9’H x 16’W x 5’D QTY 8 Poles
4’-4 ½”
QTY 6 Poles
7’-10 ½”
QTY 4 Poles
4’-9”
DIY Bay 1” EMT Pole Kit Chart
For customers who purchased the 1” EMT Pole Kit
6
1) BUILD
BOTTOM
2x 3-Ways
2x 90°
2x Depth poles
2x Width pole + coupler
2) BUILD
REAR
2x 3-Ways
4x Height poles + couplers
2x Width poles + coupler
3) BUILD
DEPTH 2x Depth poles
4) BUILD
FRONT
2x 3-Ways
4x Height poles + couplers
2x Width poles + couplers
Cage assembly for EMT Pole Kit
●SkyRailPlus customers see page 8 for cage modifications.
●See page 5 if you did not purchase the EMT Pole kit.
●Insert poles 4 ½” into connectors as noted on page 3.
7
For precut pole count and lengths see
DIY Bay 1” EMT Pole Kit Chart
IMPORTANT: BEFORE PROCEEDING
Verify that the outer dimensions match the
expected size. If not, adjust connection depths
as needed.
Depth
Width
Height
Confirm Cage Size
9
Add Blackout Sleeves
●2x Blackout Velcro sleeves
(top depth poles only)
10
Install the Wrapper
●Drape wrapper over the
cage with grommets at
the back.
●Wrap sides under bottom
depth poles connecting to
velcro.
●Wrap front edge around
front height and width
poles last connecting to
velcro.
11
Wrapper continued…
●Bungee wrapper to rear
poles.
Bungee balls face toward inside
of the cage.
Rear of cage
12
Install the Screen
●AllSportSystems Logo should
face to the front. Velcro is
sewn along all edges of screen
front.
●Starting at the corners, bungee
the screen to top and bottom
poles.
●Bungee to side poles last.
Close wrapper flaps
●Close Flaps on wrapper and
bungee to rear poles.
Bungee balls for screen installation should
face outside the cage.
Rear of cage
screen
13
Install Baffle net (optional)
●If you purchased baffle net, use
cable ties to attach the net to
the rear of of the cage.
Close wrapper flaps
●Close flaps on wrapper and
bungee to rear poles.
14
Install trim fabric
and optional foam inserts
1. Attach long edge of trim
fabric to side wall velcro.
2. Position optional foam
wedges as shown.
Wrap trim fabric around
foam and attach to screen
velcro.
Bungee balls may need to be adjusted when attaching fabric
trim to main wrapper.
●Complete both sides
and top in the same
manner.
12
15
Install bottom trim
and optional foam inserts
1. Attach trim fabric to
bottom pole using
ball bungees
2. Place foam wedges
on trim fabric.
3. Wrap fabric around
foam and velcro to
bottom of screen.
1
3
2
16
Trim panels will overlap each other.
Finished Trim
17
Other manuals for DIY Bay
1
Other AllSportSystems Sport & Outdoor manuals
