Creek Company ODC SPORT LT OUTDOOR DISCOVERY CRAFT User manual

ODC SPORT LT TM
ASSEMBLY INSTRUCTIONS
THIS BOX CONTAINS:
STEEL FRAME
(1) Left Frame Member (1) Right Frame Member
(1) Seat Support Frame Member (1) Plastic Seat Back
(1) Plastic Seat Bottom (2) Seat Assembly Pins
(4) Seat Screws (2) Foot Bars
(1) Rear Frame Member (1) Mesh Cargo Deck
(1) Stripping Apron (8) Snap Pins
OARS & OARLOCKS
(1) Pair 6-foot 2 piece Oars
(1) Pair Clamp-on Oarlocks
(2) Oarlock Bushings
PONTOONS
(1) Left Pontoon
(1) Right Pontoon
Each Pontoon consists of Nylon Cover with PVC bottom featuring integral Side Storage
Pockets, Straps and Cam-lock Buckles to secure the Frame; and Main Bladder
with Valve Insert and Valve Plate all preassembled.
PATCH KIT
WARRANTY CARD
OUTDOOR DISCOVERY CRAFTTM

ODC SPORT LT TM
ASSEMBLY INSTRUCTIONS
OUTDOOR DISCOVERY CRAFTTM
I. PLASTIC SEAT ASSEMBLY
1. Assemble Seat Back to Seat Bottom using Seat Assembly Pins (see gure 1a).
II. ASSEMBLE FRAME
NOTE: Your Frame Assembles using (8) Snap Pins. Please follow instructions accordingly.
1. Assemble Cargo Deck by sliding Mesh Cargo Deck over Rear Frame Member (see gure 1) and secure using attached Hook and
Loop and Ladder Lock/ Strap Fasteners.
2. Assemble Seat to Seat Support Frame Member using (4) Seat Screws. (See Figure 1a)
3. Assemble Seat Support Frame Member to Left and Right Frame Members using (4) of the Short Pins. (see gure 1)
4. Assemble Cargo Deck to Left and Right Frame Members using (2) Snap Pins (see gure 1).
5. Assemble Foot Bars to Left and Right Frame Members using (2) Snap Pins (see gures 1).
III. PONTOON INFLATION
NOTE: Use double action pump with Boston Valve adapters (Not Included), available from the Creek Company. Or use any
standard double action pump.
1. Inate each Pontoon. The Valve is located inside the Storage Pocket of each Pontoon.(see gure 3).
Inate until rm (do not over inate).
2. Be sure top Valve Cap and Valve Assembly are fully seated.
PONTOON DEFLATION: Unscrew entire Valve Assembly from Pontoon.
IV. ATTACH PONTOONS TO FRAME
NOTE: Always inate the Pontoons rst, before attaching to Frame.
1. Position inated Pontoons under the Left and Right Frame Members with ODC SPORT LTTM logos oriented to the
outside.The Frame Members t around the Storage Pockets.
2. Attach Pontoons to Frame as illustrated in gures 3 and 3a. Note: Be sure the Straps are pulled tight through the
Cam-lock Buckles. Frame should be positioned forward or aft on the Pontoons to achieve center of gravity for an even
ride when fully loaded on the water.
V. OAR & OARLOCK ASSEMBLY
1. Loosen the wingnut on the Oarlock and slide the Oarlock onto the handle end of the Oar Shaft.
2. Attach Blade end of Oar to end of Oar Handle.
3. Place Oarlock Shafts into Frame.
4. With the Oarlocks installed on the Frame, the oars should be equally adjusted left and right allowing at least two
thumbs’ distance between the Oars, to avoid pinching your thumbs when rowing. With the blades perpendicular to
the water, tighten the wingnuts.
VI. ATTACH STRIPPING APRON TO FRAME
1. Snap front two Straps around the Frame underneath the Oarlocks, and snap the back two straps to the Right and Left
Frame Members just behind the Storage Pockets

b
e
Fig. 1
Frame assembly
a. Cargo Deck (Rear Frame
Member with Mesh
Cargo Deck)
(assembly required)
b. Left Frame Member
c. Right Frame Member
d. Seat Support Frame Member
e. Foot Bars
a
b
Seat
Assembly
Pins
c
Fig. 1a
Seat Frame assembly
a. Plastic Seat Back
b. Plastic Seat Bottom
c. Seat Support Member Fig. 3
Pontoon-to-Frame attachment
Frame slips over two Storage Pockets
Fig. 2
Detail of Snap Pin
installation
All Frame parts attach with Snap Pins.
Your Frame assembles using (8) Snap
Pins. Please follow instructions
accordingly.
Strap
D-Ring
Frame
d
c
HIN
HIN
Accessories are available
for your ODC Sport LTTM
Visit
www.CreekCompany.com
for details or call
970-879-5221 x 300
a
Valve inside
storage pockets
Fig. 3b
Valve insert
detail
Top Valve Cap
Valve Assembly
Valve Plate
Bladder
D-Ring

ODC SPORT LT
TM
OUTDOOR DISCOVERY CRAFT TM
Your ODC Outdoor Discovery CraftTM is designed to give you many years of service.
Please follow ination instructions and warnings carefully.
IF YOU EVER HAVE ANY QUESTIONS OR PROBLEMS WITH YOUR ODC SPORT LTTM PLEASE DO NOT
RETURN IT TO THE DEALER YOU BOUGHT IT FROM. PLEASE CONTACT THE CREEK COMPANY
DIRECTLY AT 970-879-5221.
WE ARE OPEN M-F 9AM-5PM MOUNTAIN TIME. OR CONTACT US VIA E-MAIL AT [e-mail].
HIN is located on square tubing of seat support frame member and on right main frame member (See Figure 1)
Your Creek Company Sport LTTM is guaranteed against defects in material and workmanship for the life of the product to the
original owner. This does not cover damage due to misuse or normal wear and tear.
Warning:
Please read and follow carefully.
1. Always wear a US Coast Guard approved personal otation device when in your ODC SPORT LTTM.
2. Never oat alone.
3. Always check your ODC SPORT LTTM Air Bladders, Frame, Oar Components and Pontoon Covers for possible damage before
you use your craft.
4. Never use your craft if you suspect the Air Bladders, Frame, Oar Components or Pontoon Covers have been damaged.
5. Never overinate your ODC SPORT LTTM.
6. Never use your ODC SPORT LTTM without the Air Bladders fully inated.
7. Your ODC Sport LTTM is not designed for use in salt water.
CARE AND MAINTENANCE:
1. If your Pontoon Bladder is losing air, please check that Valve Assembly and Top Valve Cap are fully seated. Reseat valve
assembly and repeat pontoon ination instructions.
2. Do not store your ODC SPORT LTTM in direct sunlight.
3. If you are leaving your ODC SPORT LTTM out in the sun for any amount of time, be aware that the heat can increase the
pressure inside the Pontoons to a dangerous level. Let some of the air out of the pontoons if the craft will be out of the water in the
sun for any length of time, or if it is stored in a vehicle, etc.
4. A gain in altitude will increase the pressure in the Pontoons also. If you are taking your inated ODC SPORT LTTM from a
low elevation to a high elevation, be sure to let some of the air out of it.
5. For short term storage, we recommend you let some air out of your pontoons.
6. For long term storage, we recommend you make sure your ODC SPORT LTTM is completely dry, deated and stored out
of the sunlight in a cool dry area.. Do not store your wet ODC SPORT LTTM in freezing temperatures as this may result in
Frame and other component damage.
7. Repairing Bladder, use enclosed patch kit. Identify puncture. Fully deate Bladder. Clean and dry area around puncture. Apply
glue to puncture area and patch using applicator straw. Press patch over puncture area. Allow 24 hours to dry, before inating.
8. Note: Metal parts may rust and are not covered under warranty.
9. We recommend the use of electric trolling motors only on your SPORT LTTM
10. Do not use the Cargo Deck as a Standing Platform. It is not designed for this and may break if used in this capacity.
View instructional video at www.creekcompany.com
Accessories are available for your ODC SPORT LTTM .
Ask for them where you bought your ODC SPORT LTTM, or visit the
Creek Company Store at www.CreekCompany.com
Creek Company, PO Box 773892, Steamboat Springs, CO 80477
email: [email protected]
Made in China
Specications and other details subject to change without notice.