manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Crest Audio
  6. •
  7. Rack & Stand
  8. •
  9. Crest Audio BRBFMXL User manual

Crest Audio BRBFMXL User manual

5 YEAR WARRANTY
Olbertz Holdings Pty Ltd ACN 010 003 933 trading as The Crest Company of 165 South Pine Road, Brendale, Queensland, 4500, Ph: 1800 812 261,
www.crest.com.au, warrants that if this Crest product purchased by you from The Crest Company or a retail outlet is found by The Crest Company to be
defective in workmanship or materials within 5 years of the date of purchase, The Crest Company will (at its election) either repair that product, replace the
product, supply an equivalent product or pay the costs of repairing or replacing the product or acquiring an equivalent product.
This limited warranty will not extend to or cover any expenses associated with removing, demounting the original product or installing the repaired, replaced
or equivalent product or all or any of its components, you must bear these expenses. It also does not cover damage or loss resulting from intentional or
unintentional misuse of, tampering with, alterations to or incorrect installation of this product or use of this product for purposes other than that for which it
is designed or in a manner inconsistent with the product’s instructions. This limited warranty also does not apply to damage or loss resulting from fair wear
and tear or events beyond The Crest Company control including but not limited to natural disasters.
In order to claim under this warranty, you must contact The Crest Company and return to The Crest Company (via our nominated reply paid address) the
product and its components and proof of purchase (including the date and location of purchase) so that The Crest Company can verify the defect and
your purchase.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major
failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods
fail to be of acceptable quality and the failure does not amount to a major failure. The benets given by this warranty are in addition to other rights and
remedies which you may have under a law in relation to the goods or services to which the warranty relates.
SAFETY FIRST
1. Installation of this TV Wall Mount will be easier with
two people.
2. Some images in this guide may vary slightly from
the actual components supplied.
3. Ensure this instruction manual is completely read
and understood before attempting installation.
4. This TV Wall Mount MUST NOT be installed
solely in plasterboard, bre cement and similar
surfaces.
5. This TV Wall Mount MUST be installed in sound
supporting structures such as those made of
timber, steel or masonry using appropriate
fasteners.
6. The supporting structure must be capable of
sustaining the combined weight of the TV Wall
Mount and the display otherwise the structure
must be reinforced.
7. The fasteners supplied in this hardware pack
allow for xing into timber and masonry only. If
installing into a supporting structure made of
steel, appropriate fasteners must be used and
sourced from an appropriate supplier.
8. Use appropriate tools and safety equipment and
ensure adequate ventilation during installation.
9. If uncertain about any aspect of installation,
contact The Crest Company or an installation
professional.
10. Please retain these instructions for future reference.
v2
PO Box 5658 Brendale
QLD Australia 4500
Customer Support
1800 812 261
www.crest.com.au
AUSTRALIAN OWNED
Proudly brought to you by:
Hardware Kit Contents
Tools Required
DRYWALL INSTALLATION (TIMBER SUPPORTS):
• Adjustable spanner/socket set
• Philips head screwdriver
• Power drill
• High speed 4.5mm drill bit
• Stud nder
• Spirit level and pencil
MASONRY INSTALLATION:
• Adjustable spanner/socket set
• Philips head screwdriver
• Power drill with hammer function
• 10mm Masonry drill bit
• Spirit level and pencil
• Hammer
BRBFMXL
FULL MOTION Extra Strong
37"-90"
TV WALL MOUNT
MEDIUM-LARGE
600 x 400 MAX
VESA COMPATIBILITY
200x200,300x300,400x200,400x400,
600x400
60kg MAX
TV WEIGHT
The maximum supported
weight is up to 60kg
-60° TO 60°
PAN
EXTEND
Step 5: Level Adjustment
1. In some instances a slight adjustment might be required to level the
TV.
2. Using a second person to help, extend the bracket out as far as it will go
as shown in gure 5 and have the second person hold the TV.
3. Loosen the tension of the 4 bolts directly behind the mounting plate
(as shown in gure 6) enough so you can carefully adjust the left and
right level of the TV.
4. Once the correct position has been reached tighten the bolts back up
again to lock the levels position. It is important not to over tighten the
bolts.
Step 6: Arm Tightening
1. In some instances the arms might require a slight tightening at the joins to prevent any downward dipping from loose arms.
2. Extend the bracket out about half way as shown in gure 7.
3. Check each of the Screws and Bolts along the arm of the bracket both top and bottom and tighten is required.
4. Once you are happy with the tightness of the arms move the bracket back into position.
E
E
6
7
5
6.3 x 55mm Lag Bolt
10 x 6 x 50mm Anchor
6 x 16 x 1.5mm Washer
Step 2: Attach Mounting Arms to TV
1. Using a second person for assistance, lay your TV face down on something soft so as not to scratch the TV screen.
Check the back of your TV to nd the appropriate mounting pattern.
2. Sort through the provided bolts (M-A to M-E) until you nd the correct size that easily ts into the back of your TV and ts snugly (the
bolt must turn at least 3 full turns, do not tighten). If you feel resistance stop immediately and select a smaller bolt.
Once you have selected the correct bolt size, use the multi-sized washer (M-F). If no bolts t you will need to go to your local
hardware supplier to nd the correct bolt and washer sizes.
3. Gently put your mounting arms (B) on the back of the TV so that the mounting holes are showing through the holes of the mounting
arms.
Step 1: Attach Wall Plate to Wall
A. INSTALLING IN DRYWALL (TIMBER SUPPORTS)
WARNING: If attaching this TV Wall Mount using this method, you MUST spread the wall plate across 2 wall studs. Wall studs can be 450mm or
600mm apart depending upon the position of the wall and the geographical state you live in. The Crest Company will not accept any damages
that may occur if only 1 stud is used.
The Crest Company holds no responsibility for incorrectly installed TV Wall Mounts.
1. Locate the centre of two adjacent timber studs using a stud nder.
(NOTE: You must use the centre of the stud to avoid cracking or splitting the timber during installation).
2. Mark a minimum of 4 xing holes over stud centres using the wall plate as a guide - position 2 at either end of the Wall Plate.
Ensure plate is level.
3. Pre-drill holes to a minimum depth of 55mm using a high speed 4.5mm drill bit. If installing in hardwood, larger diameter and
deeper holes may be required.
4. Attach the wall plate using the lag bolts (W-A) through the washers (W-C). Do not over tighten.
B. INSTALLING IN MASONRY
WARNING: Ensure you have a minimum of 35mm of actual concrete/brick thickness in the hole for the anchors. Do not drill into mortar joints.
Installer must verify that the supporting surface will safely support the combined weight of the TV Wall Mount and TV.
The Crest Company holds no responsibility for incorrectly installed TV Wall Mounts.
1. Mark a minimum of four xing holes using the Wall Plate as a guide - position 2 at either end of the Wall Plate.
Ensure plate is level.
2. Pre-drill holes to a minimum depth of 60mm using 10mm masonry drill bit. Clean out holes.
3. Fully insert concrete anchors (W-B). Tap in with hammer if required.
4. Attach wall plate by inserting the lag bolts (W-A) through the washers (W-C) into each concrete anchor (W-B). Do not over tighten.
If the back of your TV is curved or recessed you will also need to use a spacer (M-G or M-H) depending upon the amount of space
you are trying to clear. If using a spacer you will also need to use longer screws. Remember that the bolt needs to turn at least 3 full
turns.
4. Using the correct mounting bolt size and length, insert these through the corresponding hole on the multi-sized washer (M-F) to
attach mounting arms to the rear of the TV. To avoid damaging TV, do not over tighten bolts.
The Crest Company is not responsible for any damage caused by screwing the bolt too far into the back of the TV.
1a
2
Step 3: Hook Arms over Wall Plate
1. Using a second person for assistance, carefully lift the TV and hook arms over the top of the wall plate.
2. Slowly lower the bottom of the TV until the bottom of the mounting arm locks into the bottom of the wall plate.
3. Once your TV is in place tighten the screws at the bottom of the mounting arms. This will help ensure that your TV does not fall off
your wall plate during use.
4. To remove the TV from the wall plate, loosen the screws at the bottom of the mounting arms this will release the mounting arms.
Pull the bottom of the TV slightly towards you and then lift the TV from the wall plate.
5. Tighten hex screws at tilt point as required using the Hexagon Wrench (E).
Check your TV Wall Mount is secure and safe to use at regular intervals (at least every three months).
Step 4: Tilt Adjustment
1. Using a second person to help, extend the bracket out as far as it will go as shown in gure 5.
2. Loosen the tension of the bolts at the tilting mechanism using the provided Hexagon Wrench (E) enough so you can carefully
adjust the tilt angle of your TV to the desired angle.
3. Once the correct position has been reached tighten the bolts back up again to lock the angle is position. It is important not to over
tighten the bolts.
34
1b

Other Crest Audio Rack & Stand manuals

Crest Audio BRBMW User manual

Crest Audio

Crest Audio BRBMW User manual

Crest Audio BRBMON1 User manual

Crest Audio

Crest Audio BRBMON1 User manual

Crest Audio EDL II User manual

Crest Audio

Crest Audio EDL II User manual

Crest Audio BRBFML User manual

Crest Audio

Crest Audio BRBFML User manual

Crest Audio MFP5FM User manual

Crest Audio

Crest Audio MFP5FM User manual

Crest Audio BRBTAB User manual

Crest Audio

Crest Audio BRBTAB User manual

Crest Audio MFP3FM User manual

Crest Audio

Crest Audio MFP3FM User manual

Crest Audio BRBSB User manual

Crest Audio

Crest Audio BRBSB User manual

Crest Audio CSBM User manual

Crest Audio

Crest Audio CSBM User manual

Crest Audio MFPLFM User manual

Crest Audio

Crest Audio MFPLFM User manual

Crest Audio BRBFMS User manual

Crest Audio

Crest Audio BRBFMS User manual

Popular Rack & Stand manuals by other brands

Rowe Scan 450i Floorstand installation instructions

Rowe

Rowe Scan 450i Floorstand installation instructions

ErGear EGDS15B instruction manual

ErGear

ErGear EGDS15B instruction manual

Stell SHO 8050 Universal Mounting Instructions

Stell

Stell SHO 8050 Universal Mounting Instructions

Novopro PS1XXL instruction manual

Novopro

Novopro PS1XXL instruction manual

BiGDUG 200SB Guide to Assembly & Usage

BiGDUG

BiGDUG 200SB Guide to Assembly & Usage

HP 245161-B22 - 10642 42U Rack Shock Pallet reference guide

HP

HP 245161-B22 - 10642 42U Rack Shock Pallet reference guide

ICW UL182 OHAP Installation

ICW

ICW UL182 OHAP Installation

Atdec AV Cart 75 installation guide

Atdec

Atdec AV Cart 75 installation guide

ricoo CZ0200 quick start guide

ricoo

ricoo CZ0200 quick start guide

NCR 7409-K361 Kit instructions

NCR

NCR 7409-K361 Kit instructions

New Star Computer Products CPU-D075BLACK/LK instruction manual

New Star Computer Products

New Star Computer Products CPU-D075BLACK/LK instruction manual

PARK WAREHOUSE 605wf100-2 Installation

PARK WAREHOUSE

PARK WAREHOUSE 605wf100-2 Installation

CHIEF PSM-2230 installation instructions

CHIEF

CHIEF PSM-2230 installation instructions

NavePoint 00301316 owner's manual

NavePoint

NavePoint 00301316 owner's manual

Logic AV Products LG-VW70 installation manual

Logic AV Products

Logic AV Products LG-VW70 installation manual

e2 E2WM quick start guide

e2

e2 E2WM quick start guide

Konig & Meyer 21302 manual

Konig & Meyer

Konig & Meyer 21302 manual

Vac-Rac QUAD RAC instructions

Vac-Rac

Vac-Rac QUAD RAC instructions

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.