Crest Audio MFP3FM User manual

SAFETY FIRST
1. Installation of this TV Wall Mount will be easier with two people.
2. Some images in this guide may vary slightly from the actual
components supplied.
3. Ensure this instruction manual is completely read and
understood before attempting installation.
4. This TV Wall Mount MUST NOT be installed solely in
plasterboard, fibre cement and similar surfaces.
5. This TV Wall Mount MUST be installed in sound supporting
structures such as those made of timber, steel or masonry
using appropriate fasteners.
6. The supporting structure must be capable of sustaining
the combined weight of the TV Wall Mount and the display
otherwise the structure must be reinforced.
7. The fasteners supplied in this hardware pack allow for fixing
into timber and masonry only. If installing into a supporting
structure made of steel, appropriate fasteners must be used
and sourced from an appropriate supplier.
8. Use appropriate tools and safety equipment and ensure
adequate ventilation during installation.
9. If uncertain about any aspect of installation, contact
The Crest Company or an installation professional.
Please retain these instructions for future reference.
Hardware Kit Contents
ITEM DESCRIPTION QTY ITEM DESCRIPTION QTY
M-A M5 x 14mm Bolt 4 W-A Lag Bolt ST6.3 x 55mm 6
M-B M6 x 14mm Bolt 4 W-B Concrete Anchor 6
M-C M8 x 20mm Bolt 4 W-C D6 Washer 6
M-D M6 x 30mm Bolt 4 A Wall Mount 1
M-E M8 x 30mm Bolt 4
M-F Washer 4 B Mounting Arm 2
M-G Small Spacer 8 C Stud Finder with Spirit Level 1
M-H Large Spacer 4
Tools Required
DRYWALL INSTALLATION (TIMBER SUPPORTS):
• Adjustable spanner/socket set
• Philips head screwdriver
• Power drill
• High speed 4.5mm drill bit
• Pencil
MASONRY INSTALLATION:
• Adjustable spanner/socket set
• Philips head screwdriver
• Power drill with hammer function
• 10mm masonry drill bit
• Pencil
• Hammer
MFP3FM
TV Wall Mount
Compatible TV Size
This TV Wall Mount fits 37-70”
(94-178cm) TV Screens
37-70”
Maximum TV Weight
This TV Wall Mount supports TVs
weighing up to 60kg
HOLDS
60kg
Maximum Mounting Pattern
This TV Wall Mount has a mounting
hole pattern up to 400x800mm (HxW)
400x800mm
Full Motion
This TV WallMount allows you to move
your TV at all angles and extends out
up to 39cm from your wall
10.

Step 1: Attach Wall Plate to Wall
A. INSTALLING IN DRYWALL (TIMBER FRAME)
WARNING: If attaching this TV Wall Mount using this method, you MUST spread the wall plate across 2 wall studs.
Wall studs can be 450mm or 600mm apart depending upon the position of the wall and the geographical state
you live in. The Crest Company will not accept any damages that may occur if only 1 stud is used.
The Crest Company holds no responsibility for incorrectly installed TV Wall Mounts.
1. Locate the centre of 2 adjacent timber studs using the supplied stud finder with spirit level.
(NOTE: You must use the centre of the stud to avoid cracking or splitting the timber during installation).
2. Mark a minimum of 4 fixing holes over stud centres using the wall plate as a guide - position 2 at either end of the wall
plate (see Figure 1). Ensure plate is level.
3. Pre-drill holes to a minimum depth of 50mm using a high speed 4.5mm drill bit. If installing in hardwood, larger diameter
and deeper holes may be required.
4. Attach the wall plate using the lag bolts (W-A) through the washers (W-C). Do not over tighten.
B. INSTALLING IN MASONRY
WARNING: Ensure you have a minimum of 35mm of actual concrete/brick thickness in the hole for the anchors.
Do not drill into mortar joints. Installer must verify that the supporting surface will safely support the combinedweight of
the TV Wall Mount and TV. The Crest Company holds no responsibility for incorrectly installed TV Wall Mounts.
1. Mark a minimum of four fixing holes (preferably 6) using wall plate as a guide - position 2 at either end of the wall plate (see
Figure 2). Ensure plate is level.
2. Pre-drill holes to a minimum depth of 60mm using 10mm masonry drill bit. Clean out holes.
3. Fully insert concrete anchors (W-B). Tap in with hammer if required.
4. Attach wall plate by inserting the lag bolts (W-A) through the washers (W-C) into each concrete anchor (W-B)
(see Figure 2). Do not over tighten.
Using the Stud Finder with Spirit Level
HOW IT WORKS:
• Use this stud finder on drywall (timber supports) only
• The stud finder accurately locates metal pipes, AC wires,
studs and wooden frames
• The stud finder LED indicator flashes GREEN when an
object is detected
• The stud finder can detect the depth of:
WOOD: up to 20mm, wood should be detected based
on the thickness of the drywall less than 20mm
METAL: up to 50mm, metal should be detected based
on the thickness of the drywall less than 50mm
VOLTAGE: up to 70mm, AC wires should be detected
based on the thickness of drywall less than 70mm
INSTRUCTIONS:
1. Keep the stud finder in touch with the drywall.
2. Press the ON/OFF button until the LED indicator turns
RED. Do not move the stud finder.
3. Wait 3 to 10 seconds until the LED indicator turns GREEN,
then start moving the stud finder on the drywall.
4. The GREEN LED indicator will start flashing when an
object is detected.
5. Mark a point on the wall using your pencil, then continue
moving the stud finder until the GREEN LED indicator
stops flashing, mark another point on your wall.
6. The midpoint between the two marks on your wall
is the centre of the stud.
Use the supplied stud finder
with spirit level to level
your TV Wall Mount
before installation
Find the wood stud, metal or
voltage before TV Wall Mount
installation
STUD

Step 2: Attach Mounting Arm to TV
1. Using a second person for assistance, lay your TV face down on something soft so as not to scratch the TV screen.
2. Check the back of your TV to find the appropriate mounting pattern.
3. Sort through theprovided bolts (M-A to M-E)until you find the correct size that easily fits into the back of your TV and fits snugly
(the bolt must turn at least 3 full turns. If you feel resistance stop immediately and select a smaller bolt.
The Crest Company is not responsible for any damage caused by screwing the bolt too far into the back of the TV.
Once you have selected the correct bolts, use the corresponding washer (M-F). If no bolts fit you will need to go to your
local hardware supplier to find the correct bolt and washer sizes.
4. Gently put your Mounting Arms (B) on the back of the TV and align to the correct holes (see Figure 3).
5. Using the correct mountingbolt size and length, insert these through the corresponding washer to attach the Mounting Arms to
the rear of the TV (seeFigure 3). If one of the larger bolts is selected then usethe hole spacers (M-C or M-E)
to fill out the WallPlate holeand reduce its size for asnugger fit. To avoid damaging TV, do not overtighten bolts.
Figure 1 Figure 2
Figure 3
W-C
W-A
W-C
W-A
W-B
M-C
M-F
M-G
M-C
M-D
M-E
M-F
M-G
M-G
M-D
M-E
M-F
M-H
M-D
M-E
M-F
M-H
M-G

5 YEAR WARRANTY
Olbertz Holdings Pty Ltd ACN 010 003 933 trading as The Crest Company of 165 South Pine Road, Brendale, Queensland, 4500, Ph: 1800 812 261,
www.crest.com.au, warrants that if this Crest product purchased by you from The Crest Company or a retail outlet is found by The Crest Company to be defective
in workmanship or materials within 5 years of the date of purchase, The Crest Company will (at its election) either repair that product, replace the product, supply
an equivalent product or pay the costs of repairing or replacing the product or acquiring an equivalent product.
This limited warranty will not extend to or cover any expenses associated with removing, demounting the original product or installing the repaired, replaced or
equivalent product or all or any of its components, you must bear these expenses. It also does not cover damage or loss resulting from intentional or unintentional
misuse of, tampering with, alterations to or incorrect installation of this product or use of this product for purposes other than that for which it is designed or in a
manner inconsistent with the product’s instructions. This limited warranty also does not apply to damage or loss resulting from fair wear and tear or events beyond
The Crest Company control including but not limited to natural disasters.
In order to claim under this warranty, you must contact The Crest Company and return to The Crest Company (via our nominated reply paid address) the product
and its components and proof of purchase (including the date and location of purchase) so that The Crest Company can verify the defect and your purchase.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure
and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of
acceptable quality and the failure does not amount to a major failure. The benefits given by this warranty are in addition to other rights and remedies which you
may have under a law in relation to the goods or services to which the warranty relates.
1440
PO Box 5658 Brendale
QLD Australia 4500
Customer Support
1800 812 261
www.crest.com.au
AUSTRALIAN OWNED
Proudly brought to you by:
Step 4: Full Motion Adjustment & Maintenance
1. You can now adjust your TV to the desired viewing angle.
2. If your Wall Mount is too loose and moves around too easily or vice versa (too tight) please tighten or loosen as required.
WARNING: Do not loosen too much as the Wall Mount may fallapart.
Check your TV Wall Mount is secure and safe to use at regular intervals (at least every three months).
Step 3: Hook Arms over Wall Plate
1. Using a second person for assistance, carefully lift the TV and hook it over the top of the wall plate (see Figure 4).
2. Tighten the two Safety bolts by using a Philips head screwdriver to secure the bracket (see Figure 5).
Figure 4 Figure 5
Safety bolts