Crosley BTD-3M11-5 User manual

1
BTD-3M11-5 Dongle Specification
v
<Product Descriptions>
• The dongle fits for Motorola APX radios
(e.x. DP3441e).
• The dongle is com atible with many
Bluetooth headsets on the aftermarket.
• Just one-time airing with wireless
headset/accessory
• O tional PTT-Z wireless PTT
<Specification>
Ty e: Bluetooth Dongle for Portable Radio
Tem : -20℃±2℃ ~ 50℃±2℃
A rox. Weight: 30g
• Fully Qualified Bluetooth v5.0
• Echo cancellation, noise reduction, also
extended features
• High-Quality DAC, Qualcomm CVC built-in
• 80MHz RISC MCU and 80MIPS Kalimba
DSP
• No battery, no need charging.
• RoHS com liant
• HSP / HFP / BLE rofile su ort
• PTT function: built-in
• Talking Range: Bluetooth class 2, 10 meters
• Dis lay LED: Blue
• TX Current: 16 mA (Average)

2
Federal Communication Commission nterference Statement
This equi ment has been tested and found to com ly with the limits for a Class B digital
device, ursuant to Part 15 of the FCC Rules. These limits are designed to rovide
reasonable rotection against harmful interference in a residential installation. This
equi ment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
articular installation. If this equi ment does cause harmful interference to radio or
television rece tion, which can be determined by turning the equi ment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the se aration between the equi ment and receiver.
- Connect the equi ment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an ex erienced radio/TV technician for hel .
FCC Caution: Any changes or modifications not ex ressly a roved by the arty
res onsible for com liance could void the user's authority to o erate this equi ment.
This device com lies with Part 15 of the FCC Rules. O eration is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must acce t any interference received, including interference that
may cause undesired o eration.
This equi ment com lies with FCC RF radiation ex osure limits set forth for an
uncontrolled environment. To maintain com liance with FCC RF ex osure com liance
requirements, lease avoid direct contact to the transmitting antenna during
transmitting.
Please kee roduct 20cm away from your body or bystander during the radio
o eration. The ty ical handheld two-way radios were certified under mobile usage
condition (i.e. kee 20cm away from the user body) and use of such radio closer than
20cm may exceed the US RF ex osure limit and shall be avoided.

3
BTD-2M11-5
vvv
Slide the switch from 0 to 1
Blue LED
Lock Switch
PTT Button

4
BT Dongle User Manual
<Pair Bluetooth headset>
1. Make sure that the Bluetooth device (headset/PTT button) aired with is off,
and there is no nearby Bluetooth device in airing mode.
2. Connect a BT dongle to the radio, ress and hold the PTT button on BT dongle
while ower on the radio until the blue LED flashes twice er second.
Then the BT dongle will enter the airing mode.
3. Power on the Bluetooth headset and lease check how to enter the airing
mode in the user manual.
Then the Bluetooth headset will be aired and connected to the BT dongle
automatically.
The blue LED on the BT dongle will flash once every 4 seconds.
< Pair Bluetooth PTT button>
1. Make sure that the Bluetooth device (headset/PTT button) aired with is off,
and there is no nearby Bluetooth device in airing mode.
2. Connect a BT dongle to the radio, ress and hold the PTT button on BT dongle
while ower on the radio until the blue LED flashes twice er second.
Then short ress the PTT button on BT dongle, the blue LED will flash 3 times
er second.
The BT dongle will enter the airing mode.
3. Power on the Bluetooth PTT button, and lease check how to enter the airing
mode in the user manual.
Then the Bluetooth PTT button will be aired and connected to the BT dongle
automatically.
The blue LED on the dongle will flash once every 4 seconds.
Note: If you only connect the BT PTT button to the BT dongle, BT PTT button will not
work. Until the BT headset is connected.
0