Crosswater MPRO US-PRO416 User manual

Installation Instructions
7-1/4" 9-3/8"
5-1/4" dia.
44"
38-3/4"
Adjustable
wrench
Channel
locks
Plumbers’ putty
or caulking
Flat head
screwdriver
Cross head
screwdriver
Hexagonal
key
Introduction
Installation notes
Dimensions
Tools required
The installation must comply with all plumbing codes including local
codes and be installed by a licensed plumbing contractor.
Anti-scald protection is the responsibility of the installer and
according to applicable codes.
Install US-418ROUGH first using the instructions provided with it.
IMPORTANT! Before installing a new faucet it is essential that the
supply pipes are thoroughly flushed in order to remove any remaining
debris, solder or other impurities. Failure to carry out this simple
procedure can cause problems or damage to the working of the
faucet.
Installing shut-off valves on incoming supply lines is recommended
for ease of maintenance.
Turn off the main water supply before connecting to any existing
pipework or doing any maintenance.
WARNING! Please check for any hidden pipes and cables, electric
or otherwise,before drilling holes in a wall or floor.
MPRO Floor-mount Tub Filler
US-PRO416
The faucets in this range are single flow (hot and cold water mix in
the body) and should therefore be supplied with hot and cold
water at balanced pressures. If the faucets are not supplied at
balanced pressures then the mixer will not function correctly. The
minimum water pressure required for these faucets is 20 psi. The
maximum water pressure is 60 psi beyond which pressure-
reducing valves must be installed.
The faucets are fitted with quarter-turn ceramic disc cartridges
which provide a good flow rate with very smooth movement.
IMPORTANT: Please read these instructions carefully before
you begin and retain for future reference. These instructions
have been prepared for your guidance, you must exercise due
care at all times.
Before beginning installation, check for any damage that may have
occurred during transport.
Note: Damage claims cannot be made during or after
installation.
We do not accept responsibility for any problems that may
occur through incorrect installation.

PLASTIC
PLATE
SCREWS x4
(Retain for
future use)
VALVE
BODY
COVER
PLATE
VALVE
BODY
UPSTAND
PIPE
740mm
LENGTH
SCREWS x4
(Retained)
HANDSET
FAUCET
BODY
HOSE
NUT
HOSE
CONE
HANDLE
PIN
COVER
CARTRIDGE
RETAINING
NUT
FAUCET
BODY
HEXAGONAL
KEY
Cleaning the cartridge
The concealed cartridge should give trouble-free service, however
servicing is a straightforward process.
To remove the cartridge
With the water supply , unscrew the pin on the handle
taking care not to mark the finish.
Using a hexagonal key loosen the set screw but do not remove.
the retaining nut and remove the cartridge.
Wash the cartridge with clean running water, dry and lightly grease
the seal, (only use silicone grease).
Replace the cartridge followed by the nut, cover and handle.
IMPORTANT:
US-418ROUGH
before following the trim installation detailed below.
With the main water supply turned off, remove the 4 screws
securing the plastic plate. Remove the plastic plate with the two
plugs. Keep the 4 screws in a safe place for future use.
Installation
Slide the cover plate up the upstand pipe, taking care not to mark
the surface.
Turn the body so that the spout is facing the correct direction.
Push the faucet body down into the valve body.
This is a pre-tested product so care should be taken not to put
undue stress on the tails as this could damage the seals within
the body of the faucet.
Fix the faucet body onto the valve body using the 4 screws.
At this point the water supply can be switched on and the unit
tested for leaks.
Extra care and time should be taken to check for leaks as the
valve body will be concealed once installation is complete.
Position the cover plate and use a suitable sealant to seal.
Connect the hose cone to the handshower.
Connect the hose nut to the faucet body.
ATTENTION:Check all new connections for leaks.
Installation
Maintenance

4 Cleaning Instructions
Rinse away any traces of soap and gently dry with a clean, soft cloth after each use. Rinse completely with water and dry any overspray. This
will maintain the finish and avoid water spotting.
To remove mineral deposits, use a 50/50 solution of white vinegar and water. Do not allow the solution to soak on the product.
Simichrome Polish® contains a protective film to enhance maintenance and is helpful in preventing water spot buildup. Follow instructions to
ensure optimum results.
Never use an abrasive material such as a brush or scouring pad to clean the surface. The use of abrasive cleaners, cleansers or disinfectants
will alter the surface finish and void the warranty.
Do not allow certain materials such as toothpaste, cologne, shaving cream, nail polish remover, vinegar, wine, drain and glass cleaners to
remain on the surface. Prolonged contact will alter surface finishes and void the warranty.
We DO NOT recommend using any household cleaners as many can cause damage to the finish.
Please see the website for care instructions for specific finishes.
Issue date: 18112019
For further information contact: Crosswater London , 393 Fortune Blvd., Milford, MA 01757
Toll free number: 844-XWATER-1 (844-992-8371) tel: [phone] fax: [phone]
www.crosswaterlondon.com
[email protected]
Warranty - This Crosswater London product is covered by a limited lifetime warranty. For full details, terms and conditions please visit our website.