Well FCT-EL-WHIPPY-WL User manual

INSTRUCTION MANUAL
INSTANT HEATING ELECTRIC FAUCET
Thank you for choosing WELL. Please read carefully the following instructions and keep them
within reach.
Reorder No: FCT-EL-WHIPPY-WL

Important note
➢This product is strictly forbidden to be used outdoors and frozen area.
➢For the first time use, please run water, then plug the power.
➢The outlet water temperature should be less than 60˚.
➢The nozzle should be cleaned regularly, must disconnect the power when cleaning.
➢If water freezes in faucet, strictly prohibited to connect to electricity power.
➢Ensure this faucet connect with earth line, otherwise not use this faucet.
➢The faucet need water pressure is 0.04MPa-0.5Mpa.
➢Please turn the knob to cold water area for 5 seconds after each using, to avoid scalding
hands when next time use, which also extend service life of the heating element.
➢If the supply cord is damaged, it must be replaced by the manufacturer or its service
agent or a similarly qualified person in order to avoid a hazard.
➢When using the electric faucet, do not use other high-power electric appliances (such as
air conditioning, induction cooker, electric kettle, etc.)
➢This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
➢Children should be supervised to ensure that they do not play with the appliance.
➢The outlet must not be connected to any tap or fitting other than those specified.
➢These appliances are not intended for showering purposes.
➢This appliance can be used by children aged from 3 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved. Cleaning and user maintenance shall not be
made by children without supervision.
➢The water inlet of this appliance shall not connected to inlet water obtained from any
other water heating system.
➢This appliance is not to be used for a potable water supply.
Preparation work before installation
Because this faucet power is larger, please check electricity meter, electric brake, fuse,
whether there is a switch on the electric circuit. The capacity of these devices should
satisfy the need of rated current of faucet.
Make sure there is earth line in the plug base. That is the actual existence of earth line in
the plug base.
Before use, please check whether the actual voltage correspond with voltage marked on
the faucet. If the user is not understand, please contact the local dealer.
Installation method
1.Remove the previous faucet, side installation method as shown picture 1
Stand installation method as shown in picture 2
According to the picture shown, please fix and connect with the corresponding waterway,
install the safety valve between the city water pipe and faucet water inlet.
2.Turn the knob and let the water out, check various components whether water leakage,
if normal then continue in the next step --- installation of circuit.

3.As picture shown, connect the faucet to the power supply, fix the faucet power line on
the wall by the cable clip (Do not damage the power line).
4. Turn the knob to hot water area, digital display working and show temperature, heating
start. Turn the knob to cold water area, display darkens and stop heating.
Rated voltage
220V –240V
Rated frequency
50 / 60 Hz
Rated power
3000 –3600 W
Waterproof
IPX4
Water pressure
0.04-0. 5 MPa
Picture 1

Picture 2
Usage method
1.Handle switch using method:
As shown picture, the handle of the rotation range is 150˚, hot water area 60˚, cold water area
60˚, middle 30° area no water.
2. Temperature display
The display shows the heating temperature, also indicate the working state of the faucet, when
the display is on the faucet is in heating mode, if the display turn off the faucet stops heating.
3.Nozzle regular cleaning method
Open the nozzle, flush it under the high pressure tap, if cannot clean dirty inside of the nozzle,
please poke using needle, as shown below.

Cause analysis and troubleshooting
Troubles
Trouble cause
Solution
Not heating water
No power or water pressure is too
low.
Check the power supply, the
minimum pressure not less than
0.04Mpa.
Water temperature low
The water pressure is too high or
the voltage too low.
Reduce outlet water, check the
voltage.
Water temperature high, outlet
water little
Inlet blocking or water pressure low
Check and remove the dirt at the
inlet strainer, if still problem,
means water pressure too low.
Temperature display is not bright
Water pressure too low, circuit fault
or tap fault.
Let water pressure normal, check
the circuit, contact the local dealer.
Waste electrical and electronic equipment are a special waste category,
collection, storage, transport, treatment and recycling are important
because they can avoid environmental pollution and are harmful to
health. Submitting waste electrical and electronic equipment to special
collection centers makes the waste to be recycled properly and
protecting the environment. Do not forget! Each electric appliance that
arrives at the landfill, the field, pollutes the environment!
Importer & distributor:
SC VITACOM ELECTRONICS SRL
CIF: RO 214527
Tel. [phone]*
[email protected], www.vitacom.ro