Crux CFD-03F User manual

FORD
2004- UP F-Series 150/250/350
PARTS INCLUDED
(1) Black Plastic Handle
(1) 18mm Bullet Camera
(1) 19ft RCA Video Cable
(1)
Instruction Sheet
TECH SERVICES
F-SERIESTAILGATE
HANDLE
WI CAMERA
SAFETY PRECAUTIONS
CFD-03F
1. Please read through the entire instruction manual before starting any of the installation procedures.
2. This product is under Crux's 1 year manufacturer's warranty. Warranty may be voided in the case where
the device shows proof of being opened or improper extreme force.
All
our products are manufactured under strict quality control. Each device is being tested before shipment. If nevertheless do occur problems
if you have technical questions, contact us directly: Crux Interfacing Solutions Tech Support
1 [phone] (Mon- Fri- 9:00AM-5:00PM) Pacific Time
INSTALLATION OVERVIEW
CAMERA
INPUT
19FT
====!mmrr . !: ·· D c::qJi]! i iiUmi----E-XT_E_NS_IO_N_,
SPECIFICATIONS:
CAMERA:
Sensor: CCD
Size: 18mm
Viewing Angle (H): 170°
Viewing Angle
(V): 90°
TV System: NTSC I PAL
Guide Lines: Yes
Invert Image: No
Resolution: 480
TV Lines
Illumination: 0.4 Lux I F1.2
Power Supply: 12v
Waterproof: IP67
Rev.040815
RED/
TO REVERSE
BLACK I .!. I
GROUND
BLACK BARREL I
CAM POWER
!!!!
i
I
I
~
iii
CAMERA
LOCATION
'
..
~
i
YELLOW RCA/
VIDEO SIGNAL
F-SERIES T AILGA TE
HANDLE
KEY CYLINDER
LOCATION
www.cruxinterfacing.com

CRUX
ll~iij;Jfdil~tCJ1elliiittl~b4-
INSTALLING
THE
TAILGATE
HANDLE
Follow these steps
to
properly install the Tailgate Handle.
F-SERIES
TAILGATE
HANDLE
W/CAMERA
Step
1
Remove
Tailgate
Cover-
Start by lowering the tailgate
of
the truck. Remove the tailgate cover by using a
T-30
torx bit,
rem
.ove (8-13 depending on the model) torx bolts
that
secure the tailgate cover.
CFD-03F
Step
2
Remove
Tailgate
Handle
-After
removing
the
tailgate cover you will have
access
to
the backside
of
the factory tailgate handle.
Using a 1
Omm
socket, remove the
(2)
nuts holding the tailgate handle in place. Lift up on the latch
to
release the
(2)
tailgate handle studs and
remove the tailgate handle.
Step
3 Set
Up
New
Handle-
On
the lock cylinder, remove the metal clip that holds the locking mechanism in place. Re-Install the locking
mechanism onto the new tailgate handle.
Take
the included camera and insert
into
the new tailgate handle
..
Tip : Insert the Video
RCA
and Power wires
through the camera hole first.
F-SERIES
TAILGATE
HANDLE
Step
4 Re-Install
New
Tailgate
Handle-
Re-assemble the new tailgate handle
into
the tailgate in reverse order.
Route the wiring
to
power the camera towards
the
bottom
of
the tailgate and through
an
access
port
to
reach underneath the truck.
Step
5
Routing
The
Video
and
Power
Cables
-Route
the Video and Power cables from the tailgate
of
the truck towards the radio
location where the rest
of
the installation
of
the camera will take place.
You
will need
to
connect
the
RED
power wire
to
REVERSE
and the
BLACK
wire
to
ground.
Tip: There should
be
an
opening between
the cabin and the bed
of
the truck
where you
can
insert the cables
into the cabin
area.
Rev.
040815
2
www.cruxinterfacing.com

CFD-03F