CTM LYNG Mkomfy R-T 25A User manual

Installation instructions/User instructions
Mkomfy R-T 25A
SAVE THESE INSTRUCTIONS
Panel-installed cooker guard relay
Mkomfy set with sensor and relay
is supplied ready paired and ready for use
Fulfils the requirements
of NEK 400:2014

2
User information
Microsafe Mkomfy is a safety product from CTM Lyng AS.
The product is mandatory for new installations and major
renovation projects and is intended as extra safety for avoiding
uncontrolled fire breakout and damage to property.
The product assumes normal care in the use of the cooker and
associated cooking implements. In normal use the cooker should
be kept under frequent observation, even if safety equipment
such as Mkomfy is installed.
Time function
When Mkomfy detects heat on the hob, an integral timer starts up.
After 2 hours, the power supply is turned off, even if no overheating
isdetected.
5 minutes before the time expires, Mkomfy will emit a sound signal once
every 15 seconds. If you need to continue cooking, a short press on the
function button within the last five minutes will extend user time by an extra
30 minutes. This can be repeated if a new warning is given and your cooking
is still not finished.
Anti-tamper function
If the sensor is removed from its bracket, a safety function is activated which
cuts off the power to the cooker. On activation, the sensor will beep once
asecond for 5 seconds, before disconnecting the cooker. To start the cooker,
replace the sensor in the bracket and press the function button (short press).
Overheating
An absolute limit has been set for the maximum temperature on the hob.
Therule is that a frying pan with fat must not get so hot that it catches
fire. In the case of overheating, Mkomfy will emit an alarm of 3 short sound
signals every 5 seconds. Normally, if you operate the function button within
40seconds of hearing the alarm, you will have 5 minutes more user time,
oryou can take steps to reduce the temperature and continue as normal.
Ifthefunction button is not pressed, the cooker will turn off after 40 seconds.
Please remember that if you slide a frying pan or saucepan over onto another
cooker element, you will be uncovering a very hot element as well as the hot
frying pan/saucepan. Mkomfy may detect this as overheating and shut down
the cooker after an overheating warning.
The product requires correct installation and maintenance as described.

3
Do visit us on
www.ctmlyng.no/komfyrvakt
or scan the QR code on the right
with your smart phone for more
information and documentation
regarding the cooker guard.
Sound alarm
1 sound signal: Timer function,
timeexpired.
2 short sound signals:
Batteryneedschanging.
3 short sound signals: Over-heating.
Function button
One press will extend the
time by 30 min, orturn
the cooker on after
disconnection.
Temperature sensor
Must be cleaned regularly with
a cloth dampened with slightly
soapy water.
Light
Changing the timer function
The timer function can be temporarily changed from 2 hours
operating time to 12 hours operating time.
This is done by pressing the function button for 10 seconds.
The sensor acknowledges this with two sound signals. During the
last five minutes of the twelve hour period, the sound emitter
will produce a sound signal every 30 seconds. If cooking is to
proceed for more than 12 hours, pressing the function button
within the last 5 minutes will extend user time by 30minutes.
This can be repeated if cooking is still not finished and a new
warning is given. If it is wished to reset Mkomfy to 2hours
operating time, press the function button for 10 seconds,
andthesensor will acknowledge this with a single sound signal.
User information

4
Battery change
Recommended every three years or when the battery warning
signal is given. The sensor will warn about battery change when
necessary. This is done by 2 short sound signals every 5minutes.
1. Flip the cooker guard away from the wall.
2. Loosen two screws on the rear and remove the cover.
3. The batteries can then be turned out and replaced.
Battery type AAA (ordinary remote control batteries)
Make sure the batteries are correctly installed.
User information

5
Quick instructions
1. Mount the relay.
2. Mount the sensor.
3. Brief press on button (sensor BEEP = relay response OK)
Installation information for sensor
Carefully clean the wall and make sure it is dry before pressing the
cooker guard into place at the correct height (remove the backing
tape). The adhesive foot must be fixed to the cooker guard.
Installation information
40 to 50 cm
30 cm
60 cm
60 cm
30 cm
Centre cooker guard
Centre cooker
NB: If a screw is used to fix the foot, the screw head may not be greater
than 6.9 mm in diameter or protrude more than 2.5 mm.

6
To test for function, run a “forehead test”
4.
You have now tested all functions.
Remember to set switch 4 back
to OFF position and remount
thesensor.
1.
Unscrew the rear cover of the
sensor and set slide switch 4 to
position ON.
Slide switch
2.
Point the sensor eye marked ①
towards your own face/forehead
and check that the cooker turns
off (the temperature of your
forehead is over 30°C).
Sensor
①
3.
Point the sensor eye marked ①
to a cold surface (at normal room
temperature) and the cooker will
turn on again (the surface is colder
than 30°C).
Sensor
①
Function test
Installation information

7
Function button
DipSW
Rear
Front
Dip 1 Not in use
Dip 2 ON: *Extra-high temperature
Dip 3 ON: **Induction
Dip 4 ON: Function test and pairing mode. See pages 6 and 8.
**Induction
When using a powerful induction cooker, safety can be
increased by shortening the alarm period so that the cooker
cuts out after 20 seconds in the event of overheating, rather
than the standard 40 seconds.
* Extra-high temperature (To be carried out only by an
authorisedinstaller)
In certain locations or with certain types of hob, the sensor
may be slightly over-sensitive. In such cases, the overheating
temperature may be raised by 15 degrees. This function
should be used with great care, as it may affect the safety
of the product. We recommend that the sensor is used as
supplied, in off-position.
Sensor
Installation information

8
Pairing of Sensor and Cooker Guard Relay
The Mkomfy set with sensor and cooker guard relay in the same pack are
already paired. If you have bought a separate sensor, this must be paired
with the cooker guard relay. This can be done in two different ways.
Read through the whole instruction for both alternatives before performing pairing!
Alternative 1:
Pairing of Sensor without physical intervention on cooker guard relay.
1. Activate Sensor in pairing mode by setting DipSW 4 to active [ON].
2. Disconnect the power to the cooker guard relay for 5 seconds by
turning the relevant fuse circuit off and on.
- Within 20 seconds of turning the fuse circuit on:
Hold in the function button on the sensor for 6 seconds.
The sensor will emit a sound signal every 2 seconds, if pairing
hassucceeded.
3. Once again, disconnect the power to the cooker guard relay
for5seconds by turning the relevant fuse circuit off and on.
NB! This must be done within one minute of connecting the
relay under Point 2, or the pairing will not be saved
4. Set DipSW 4 back to inactive [OFF].
Pairing is now complete.
Alternative 2:
Pairing of Sensor by activation of programming button on cooker guard relay.
1. Activate Sensor in pairing mode by setting DipSW 4 to active [ON].
2. Briefly press the programming button on the cooker guard relay.
Yellow diode will now begin to flash. The cooker guard relay will
now be in pairing mode for 30 seconds.
3. Hold in the function button on the sensor for 6 seconds while
the yellow LED flashes. The sensor will emit a sound signal every
2 seconds, if pairing has succeeded.
4. Set DipSW 4 back to inactive [OFF].
NB: It is not possible to have more than 1 Mkomfy Sensor connected to the
Cooker Guard Relay at the same time. Pairing a new sensor will automatically
delete the sensor already paired with the cooker guard relay.
Installation information

9
Overview of cooker guard relay
R-T 25A
Prog.
Blue
Yellow
Red
Green
Programming button
Installation information
Green Lights up continuously while the relay is connected.
Flashes if there is no communication with the sensor *
Red Flashes when paired units are deleted or
if the command from the sensor is rejected.
Yellow Flashes when the relay is set to pairing mode.
Blue Indicates radio communication. Flashes when
button on sensor is pressed. *
* Green and blue flash simultaneously when relay is in emergency mode.
Explanation of LEDs

10
Installation is not complete until the radio connection has been
checked by pressing the function button on the Sensor and noting
that the red diode on the relay responds with a flash and that the
Sensor acknowledges this with a sound signal and red flash.
R-T 25A
Prog.
N N
L L
IN LOAD/CONTACTOR*
*Can also control a contactor. This is recommended when
the RC circuit is mounted in parallel with the coil on
thecontactor.
Installation information
Deletion of connected units on Socket
Hold the programming button in for 8 s until the Red diode begins
to light up. Do not release the button until this diode starts to flash.
Allconnected units are now deleted.