CTM LYNG MICROSAFE mKomfy 16R400V-D Guide

Installation and User Instructions
SAVE THESE INSTRUCTIONS
mKomfy Hybrid 16R400V-D

2
Practical information
The mKomfy cooker is a safety product developed to
minimise the risk of fire when cooking. The product provides
normal safety when using a cooker and associated cookware.
Thecooker must not be left unattended while in use even if
safety equipment such as the mKomfy is installed.
The product must be installed and maintained correctly
as described, and may only be fitted by an authorised
electrician.
Accessories
Skins for the front panel
The accessories for the mKomfy include
several products that increase the level of
safety. Compatible with wireless accessories
labelled "v2".
External
reset button*
External
master switch
Smoke
shut-off
* Recommended for ceiling mounting – performs the same function as the
control button
On our website, you can find dimensioned sketches
for making your own skins, which you can cut to
size and position under the sensor’s front panel.
See www.ctmlyng.no/hybrid

3
Safety functions
Hotplate temperature
The cooker guard monitors the temperature of the hotplates and
sounds the alarm if it exceeds the upper limit. The temperature alarm
beeps 3 times every 5 seconds for 20 seconds and a red light comes on
in the sensor. Reduce the temperature of the hotplates immediately
to prevent them being turned off or press the control button on the
sensor to approve the higher temperature for a set time.
Anti-tamper function
If the sensor is removed from the bracket, a security function will
be activated and beep 5 times in 5 seconds before the hotplates
are turned off. Put the sensor back and press the control button to
continue using the cooker.
Optional timer function (see page 12 for activation)
When the cooker guard detects that the cooker has been turned
on, itcan start a built-in timer (countdown clock). When the timer
reaches zero, the cooker is turned off. The cooker guard will alert the
user for the last 5 minutes. Press the control button on the sensor
once to restart the timer.
Hold the control button in for 10 seconds to extend the time
(seepage 5).
Things to remember when cooking:
Moving a hot pan to another hotplate will expose a very hot surface.
The cooker guard may register this as overheating and sound the
alarm. To reduce the risk of unwanted temperature alarms, only use
pans that cover the entire hotplate.

4
Everyday use
Batteries (does not apply if an external power supply is used)
We recommend replacing the batteries once a year or when there is a
low battery warning.
1. Remove the sensor from the bracket.
2. Replace the batteries (3 x “AA”).
3. Put the sensor back in the bracket.
4. Give the control button a quick press.
The sensor will beep if the new batteries are in properly.
Control button
• Reset alarm
• Extend cooking time
• Reset cut-out
Light
See page 2 for optional
design/colour using skins
Taking the sensor off/putting the sensor on the sensor bracket
(battery cover)

5
Everyday use
Temporarily extended time
(Only applies if timer function is activated, see page 3)
The timer (countdown clock) can temporarily be extended to
12hours by holding the control button in for 10 seconds.
The sensor beeps twice to confirm that the extended cooking time
has been activated. The timer returns to normal operation when
thecountdown ends or the cooker is turned off.
Hold the control button in for 10 seconds to end the extended
cooking time. The sensor beeps once to confirm.
Alarms
Alarm signal: One (1) beep every 15 seconds for 5 minutes.
Cause: Cooker guard warning that timer will run out in
5minutes.
Action: Press control button to restart timer.
Alarm signal: Five (5) beeps in 5 seconds.
Cause: Anti-tamper function detects that sensor is not
positioned correctly in wall bracket.
Action: Position sensor properly in bracket and press
control button.
Alarm signal: Two (2) beeps every five minutes.
Cause: Batteries are nearly flat.
Action: Replace batteries. Remember to check that you
have new batteries before taking the old ones out
of the sensor (3 x AA).
Alarm signal: Three (3) beeps every 5 seconds and red light.
Cause: Hotplates overheating.
Action: Turn temperature down or press control button to
temporarily approve high temperature.

6
B
tak høyde
C
tak høyde
D
A
sensor
kjøkkenøy
a - framkanten av
platetopp
b - bakkanten av
platetopp
b - bakkanten av
platetopp
kjøkkenøy
sensor
benkventilator
takintegrert ventilator
Sensor installasjonsinstruks til kjøkkenøy med fritthengende ventilator over platetopp. Tegning fig.1-1
Sensor installasjonsinstruks til kjøkkenøy med benkventilator eller takintegrert ventilator. Tegning fig. 1-2
fritthengende ventilator
figur 1-1
figur 1-2
Kjøkkenøy med :
Fritthengende
ventilator,
benkventilator eller
takintegrert ventilator
Ventilator
monteringshøyde fra
platetopp
Sensor plassering på
ventilator - avstand
målt fra framkanten
(a) av platetopp
Sensor plassering på
tak, høyde = 2,4 m
- avstand målt fra
bakkanten (b) av
platetopp
Sensor plassering på
tak, høyde = 2,7 m
- avstand målt fra
bakkanten (b) av
platetopp
Sensor plassering på
tak, høyde = 3,0 m
- avstand målt fra
bakkanten (b) av
platetopp
A B C
C
C
Fritthengende
ventilator
70 cm - 80 cm 8,5 cm
ikke anbefalt ikke anbefalt ikke anbefalt
80 cm - 99 cm 5,5 cm - 8,5 cm
ikke anbefalt ikke anbefalt ikke anbefalt
100 cm - 115cm
0 cm - 4 cm
ikke anbefalt ikke anbefalt ikke anbefalt
≥
115 cm
0 cm 80 cm 95 cm 110 cm
Kjøkkenøy med:
benkventilator eller
takintegrert ventilator
Sensor plassering på
tak, høyde = 2,4 m
- avstand målt fra
bakkanten (b) av
platetopp
Sensor plassering på
tak, høyde = 2,7 m
- avstand målt fra
bakkanten (b) av
platetopp
Sensor plassering på
tak, høyde = 3,0 m
- avstand målt fra
bakkanten (b) av
platetopp
D
D
D
Benkventilator eller
takintegrert ventilator
70 cm - 80 cm 70 cm- 95 cm 70 cm - 110 cm
kjøkkenøy
PART NUMBER:
edit
DATE: DRAWN BY:
editedit
TOLERANCES:
edit
kjøkkenøy
edit
SHEET 1 OF 2 SCALE:1:20 (A3)
DRAWING NAME:
PART NAME:
REVISION:
DO NOT SCALE DRAWING
MATERIAL:
DEBURR AND BREAK SHARP EDGES
FINISH:
UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE IN MILLIMETERS
Sensor installation
Kitchen island with suspended cooker hood
Cooker hood Sensor
mounted on
cooker hood
Sensor
mounted
on ceiling,
height = 2.4 m
Sensor
mounted
on ceiling,
height = 2.7 m
Sensor
mounted
on ceiling,
height = 3.0 m
A
Mounting
height above
hob
B
Distance
measured from
front edge
(a) of hob
C
Distance measured from back edge (b)
of hob
70-80cm 8.5 cm not recommended not recommended not recommended
80-99cm 5.5-8.5cm not recommended not recommended not recommended
100-115cm 0-4cm not recommended not recommended not recommended
≥ 115 cm 0 cm 80 cm 95 cm 110 cm
Fig. 1-1
Table for Fig. 1-1
suspended cooker hood
sensor
kitchen island
ceiling height
a – front edge
of hob
b – back edge
of hob

7
Sensor installation
Kitchen island with worktop/ceiling-mounted cooker hood
Sensor mounted
on ceiling,
height = 2.4 m
Sensor mounted
on ceiling,
height = 2.7 m
Sensor mounted
on ceiling,
height = 3.0 m
D
Distance measured from back edge (b)
of hob
70-80cm 70-95cm 70-110cm
B
tak høyde
C
tak høyde
D
A
sensor
kjøkkenøy
a - framkanten av
platetopp
b - bakkanten av
platetopp
b - bakkanten av
platetopp
kjøkkenøy
sensor
benkventilator
takintegrert ventilator
Sensor installasjonsinstruks til kjøkkenøy med fritthengende ventilator over platetopp. Tegning fig.1-1
Sensor installasjonsinstruks til kjøkkenøy med benkventilator eller takintegrert ventilator. Tegning fig. 1-2
fritthengende ventilator
figur 1-1
figur 1-2
Kjøkkenøy med :
Fritthengende
ventilator,
benkventilator eller
takintegrert ventilator
Ventilator
monteringshøyde fra
platetopp
Sensor plassering på
ventilator - avstand
målt fra framkanten
(a) av platetopp
Sensor plassering på
tak, høyde = 2,4 m
- avstand målt fra
bakkanten (b) av
platetopp
Sensor plassering på
tak, høyde = 2,7 m
- avstand målt fra
bakkanten (b) av
platetopp
Sensor plassering på
tak, høyde = 3,0 m
- avstand målt fra
bakkanten (b) av
platetopp
A B C
C
C
Fritthengende
ventilator
70 cm - 80 cm 8,5 cm
ikke anbefalt ikke anbefalt ikke anbefalt
80 cm - 99 cm 5,5 cm - 8,5 cm
ikke anbefalt ikke anbefalt ikke anbefalt
100 cm - 115cm
0 cm - 4 cm
ikke anbefalt ikke anbefalt ikke anbefalt
≥
115 cm
0 cm 80 cm 95 cm 110 cm
Kjøkkenøy med:
benkventilator eller
takintegrert ventilator
Sensor plassering på
tak, høyde = 2,4 m
- avstand målt fra
bakkanten (b) av
platetopp
Sensor plassering på
tak, høyde = 2,7 m
- avstand målt fra
bakkanten (b) av
platetopp
Sensor plassering på
tak, høyde = 3,0 m
- avstand målt fra
bakkanten (b) av
platetopp
D
D
D
Benkventilator eller
takintegrert ventilator
70 cm - 80 cm 70 cm- 95 cm 70 cm - 110 cm
kjøkkenøy
PART NUMBER:
edit
DATE: DRAWN BY:
editedit
TOLERANCES:
edit
kjøkkenøy
edit
SHEET 1 OF 2 SCALE:1:20 (A3)
DRAWING NAME:
PART NAME:
REVISION:
DO NOT SCALE DRAWING
MATERIAL:
DEBURR AND BREAK SHARP EDGES
FINISH:
UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE IN MILLIMETERS
Table for Fig. 1-2
Fig. 1-2
cooker hood
integrated in ceiling
sensor
kitchen island
worktop-mounted
cooker hood
ceiling height
b – back edge
of hob

8
Sensor installation
Wall-mounted hob/cooker hood
Cooker hood Cooker hood
Sensor mounted on
ceiling,
height H = 2.4 m (3.0 m)
A
depth
B
mounting height
above hob
C
distance
from wall
< 50cm min. 50 cm 88 cm (119 cm)
≥ 50cm min. 70 cm 88 cm (119 cm)
Table for Fig. 1-3
Fig. 1-3
10 cm
B
H = tak høyde
A
C
ca. 10 cm fra vegg
sensor
ved vegg
Veggplassert platetopp med vegg/skap montert ventilator. Tegning fig.1-3
figur 1-3
Sensor Installasjonsinstruks til
vegg/skap montert ventilator
Ventilator
monteringshøyde fra
platetopp
Plassering av sensoren-
avstand fra vegg for tak
høyde H = 2,4 m (3,0 m)
A B C
Ventilator dybde
<
50cm
min. 50 cm 88 cm (119 cm)
Ventilator dybde
≥
50cm
min. 70 cm 88 cm (119 cm)
ved veggen
PART NUMBER:
edit
DATE: DRAWN BY:
editedit
TOLERANCES:
edit
ved veggen
edit
SHEET 1 OF 1 SCALE:1:20 (A3)
DRAWING NAME:
PART NAME:
REVISION:
DO NOT SCALE DRAWING
MATERIAL:
DEBURR AND BREAK SHARP EDGES
FINISH:
UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE IN MILLIMETERS
sensor
H = ceiling height
approx. 10 cm from wall

9
Sensor installation
Coverage
Orientation
Arrow points towards hob
DISTANCE
HOB
2
SENSOR
MAX.
WIDTH
HOB
MAX.
DEPTH
HOB
70 73 44
75 78 47
85 88 54
95 99 60
105 109 66
110 115 69
115 120 73
120 125 76
125 130 79
130 135 82
135 141 85
140 146 88
145 151 91
150 156 95
155 161 98
160 167 101
165 172 104
170 177 107
175 182 110
180 187 114
185 193 117
190 198 120
195 203 123
200 208 126
205 213 129
210 219 132
Dimensions in cm

10
Installation
Green lights up when relay is on.
Blue flashes when data is received from
paired unit (excluding sensor)
Blue +
Green
flash
alternately
if connection with sensor is
lost (emergency mode*)
Red flashes if relay overheats – power
must be turned off.
Red flashes +
beeping,
if error in external units
interrupts pairing before
sensor is paired
Yellow lights up
when cooker’s electricity
consumption is too high,
1.2 A **
Yellow flashes in pairing mode
* Emergency mode = all safety functions deactivated
** 1.2 A is the factory default. After calibration, the LED lights up if the new
calibration level is exceeded.
1. Connecting wires in the relay (must be carried out by an authorised
electrician)
1. Connect the input wires to the terminals.
2. Connect the output wires to the terminals.
3. Turn on the power.
The sensor and relay are configured at the factory and ready to install.
See page 15 if re-pairing is necessary.
L1 in
L2 in
L3 in
N
L1 out
L2 out
L3 out
N
2. Fitting the sensor
• The sensor must be fitted at least 70 cm above the hob on either the
cooker hood or the ceiling.
• Take note of the coverage (page 9) when fitting the sensor at different heights.
• The mounting hole is suitable for mounting on a standard wall box.
1. Find a suitable location, see drawings on pages 6-8.
2. Mount the bracket.
3. Set the DIP switch to the chosen height and angle (pages 11-12).
4. Insert the batteries (2 beeps = OK) or connect an external power supply (page 11).
5. Put the sensor in the bracket and press the control button on the
sensor once. A short beep confirms that the sensor is in communication
with the socket and working.
6. Make sure that only the green LED on the socket lights up when the oven
is connected and turned off. If the yellow LED lights up, the cooker’s
standby electricity consumption is higher than the default setting.
Thelevel in the mKomfy can then be calibrated to the cooker’s actual
electricity consumption, see pages 10 and 11.
Status LED (Troubleshooting must be
carried out by an authorised electrician)