CuddleCo NOLA User manual

NOLA COT BED
Assembly instructions
IMPORTANT, RETAIN FOR FUTURE REFERENCE:
READ CAREFULLY

1
·Your child's safety is your responsibility
·Furniture can be dangerous if incorrectly installed, assembly should be carried out by a competent person
·Follow the instructions in detail to ensure the safety features of the cot are not compromised
·Take care when handling or moving furniture. Careless handling can cause damage
·Keep children away during assembly as pack contains small parts which may present a choking hazard
·Remove all parts from packaging and check against the parts list
·Do not discard any packaging until you are sure you have all parts and the fittings pack
·Assembly of the furniture will be easier with 2 people
WARNING: Be aware of the risk of open fire and other sources of strong heat, such as electric bar fires, gas fires, etc. in the near
vicinity of the cot
WARNING: Do not place this child's bed near heat sources, windows and other furniture
WARNING: Do not use the cot if any part is broken, torn or missing and use only spare parts approved by the manufacturer
WARNING: Do not leave anything in the cot or place the cot close to another product, which could provide a foothold or present
a danger of suffocation or strangulation, e.g. strings, blind/curtain cords
WARNING: Do not use more than one mattress in the cot bed
·The lowest bed base position is the safest. To prevent falls the mattress base of this cot should be adjusted to the lowest
position before the child can sit up
·The thickness of the mattress shall be such that the internal height (surface of the mattress to the upper edge of the cot
frame) is at least 500 mm in the lowest position of the cot base and at least 200mm in the highest position of the cot base.
There is a mark on the inside of the cot which shows the maximum thickness of the mattress to be used with the cot
·The cot bed is designed to be used with a mattress measuring 1400mm long by 700mm wide and 100mm tall
·The minimum size of the mattress to be used with the cot is 1370mm long by 670mm wide. There shall be no gap more than
30 mm between the mattress and the sides end ends in any position of the mattress.
·To prevent injury from falls; when the child is able to climb out of the cot, the cot shall no longer be used by the child.
·When converted into a toddler bed the product can be used from 18 months to 4 years
·Children are likely to play, bounce, jump and climb on beds, therefore the child's bed should not be placed too close to other
furniture or windows, blind cords, curtain pulls or other strings or cords, and should be placed either tight to any wall or have a
gap of 300 mm between the wall and the side of the bed
·All assembly fittings should always be tightened properly and fittings should be checked regularly and retightened as
necessary
·The bed is designed to be dismantled for transportation and storage
·Your furniture may be cleaned by wiping down with a damp cloth and dried with a soft, clean cloth. Do not use abrasives,
bleach, alcohol or ammonia based household polishes.
·The Cot bed is made to conform to safety regulations: BS EN 716-1&2: 2017 and BS 8509: 2008+A1: 2011
For questions and advice regarding this product please contact CuddleCo Customer services at:
[email protected] or go to www.cuddleco.co.uk
CuddleCo Ltd, M16 9HQ, UK
CuddleCo Baby Products Europe Ltd, 22 Northumberland Road, Ballsbridge, Dublin 4, Ireland
Safety Warnings

GETTING TO KNOW YOUR PRODUCT
Ref Dimensions Qty
Visual
1
2
3
2
2
1
Ctn
1
1
1
87 x 75 cm
140 x 65 cm
140 x 70 cm
1
1
2
2
3
Ref Dimensions Qty
6 x 60 mmA 8
10 x 13 mmB 16
N/A
D1
6 x 80 mm
C8

6 x 60 mm
10 x 13 mm
B x 4
A x 4
AB
3
6 x 80 mm
10 x 13 mm
B x 8
C x 8
B
3
C
C
C
1
A
A
A
BB
B
C
B
BB
B
B
C
C
1
6 x 60 mm
10 x 13 mm
B x 4
A x 4
AB
A
A
A
B
2
2
B
A
2
B
B
B
A
C
C
C
C
B
B
B
B
1
2
3
!
Warning, there are 3 base positions,
the lowest postion is the safest
To convert to Toddler bed remove
1 x side panel (2) using allen key (D)