Cuisinart DGB900BCU User manual

Grind & Brew Plus
DGB900BCU

Congratulations on your purchase of the Cuisinart Grind & Brew Plus
For over 30 years Cuisinart’s aim has been to produce the very nest kitchen equipment so that cooks
at home as well as professional chefs have the tools to express their creativity.
All Cuisinart products are engineered for exceptionally long life, and designed to be easy to use as
well as to give excellent performance day after day. That is why they have come to be regarded as the
dening machines in their eld by chefs across the world.
Whatever you cook, cook it better with Cuisinart.

4
CONTENTS
Product Description 5
Safety Cautions 6
Instructions for Use 9
A Control panel 9
B Programming 11
Setting the Clock 11
Setting the Programme Time 12
C Inserting the Charcoal Water Filter 13
D Preparing to Brew 14
Inserting the Filter 14
Adding Water & Coffee Beans 15
Locking the Bean Hopper 16
Preparing the Carafe 17
E Grinding & Brewing Coffee 18
Immediate Brewing 18
Programmed Brewing 18
Brewed Coffee 18
F Brew Coffee with Pre-ground Beans 20
Cleaning & Maintenance 21
Descaling 23
Troubleshooting 24
UK Guarantee 26
UK After Sales Service 27

5
Product Description
Bean Hopper Lid
Bean Hopper
Water Reservoir (not shown)
Control Panel
Filter Compartment
Filter Compartment Release Button
12 Cup Thermal Carafe
Housing Unit

6
Safety Cautions
Carefully read all the instructions thoroughly before using the appliance and keep in a safe place for
future reference.
Always follow these safety cautions when using this appliance to avoid personal injury or damage to
the appliance. This appliance should be used only as described within this instruction book.
ßAlways inspect the appliance before use for noticeable signs of damage. Do not use if damaged,
or if the appliance has been dropped. In the event of damage, remove the plug from the mains then
contact the Cuisinart Helpline (see “UK After Sales Service” section).
ßDo not use this appliance if the lead is damaged. In the event of a damaged lead discontinue use
immediately. Contact the Cuisinart Helpline. (See “UK After Sales Service”).
ßUnplug from the mains when not in use and before cleaning. Allow to cool before cleaning the
appliance. To disconnect, push the ‘On/Off’ button, and then remove the plug from the mains. Never
pull the plug out of the mains socket by its lead.
ßThis appliance should not be used by adults or children whose lack of experience, product knowledge
or disability might cause a hazard, unless they have been correctly instructed and are adequately
supervised.
ßChildren should always be supervised to ensure that they do not play with this product.
ßDo not use any accessory or attachments with this appliance other than those recommended by
Cuisinart.
ßDo not place the appliance on or near a hot gas or electric burner or in a heated oven.
ßTo protect against re, electric shock or personal injury, do not immerse cord, plug or unit in water
or other liquids.
ßDo not leave the lead hanging over the edge of a kitchen table or worktop. Avoid contact between
the lead and hot surfaces.
ßFor indoor use only.
ßFor domestic use only.

7
ßDo not exceed the maximum capacity of this appliance. (See page 15)
ßThis appliance should be used only for grinding coffee beans and brewing coffee as described within
the Instructions for Use. Please retain these instructions for further use.
ßAlways ensure that your hands are dry before removing the plug from the mains socket.
ßThis appliance complies with the requirements of Directives 04/108/EEC (Electromagnetic
Compatibility) and 06/95/CE (Electrical Safety of Domestic Appliances) amended by Directive
93/68/EEC (CE marketing).
ßNo repair should be carried out by the user. In case of fault, contact the Cuisinart Helpline, (See ‘UK
After Sales Service’ section).
WARNING: A cut off plug inserted into a 13 amp socket is a serious safety (shock) hazard. Ensure
the cut off plug is disposed of safely.
The symbol on the product or on its packaging indicates that this product may not be treated as
household waste. Instead it should be handed over to an appropriate collection point for the recycling
of electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences
for the environment and human health, which could otherwise be caused by inappropriate waste
handling of this product. For more detailed information about the recycling of this product, please
contact your local council ofce or your household waste disposal service.

8
Safety during use
ßDo not touch hot surfaces. Use handles and knobs
ßAlways ll water reservoir rst, then plug into a suitable power outlet. To disconnect, push the ‘On/
Off’ button to switch off the appliance, then remove the plug from the wall outlet.
ßEnsure lid is securely attached to the carafe before serving any beverages.
ßLiquids will reach to approximately 90˚C. Be careful when pouring beverages.
ßThe thermal carafe is designed for use with this appliance only.
ßDo not use the carafe if cracked or if the handle is loose.
ßDo not clean carafe or resting plate with cleansers, steel wool pads, or other abrasive materials.
ßAvoid contact with moving parts.
ßCheck grinder basket before use for presence of foreign objects.
ßUse the coffee grinder to grind roasted coffee beans only. Do not use to grind other substances, e.g
nuts, spices or un-roasted beans as this may damage the plates or cause injury.
ßDo not place cloth or otherwise restrict airow beneath coffeemaker.
ßUse only the Cuisinart Gold Tone® Commercial Style Filter with this unit. Other Gold Tone®
permanent lters or normal paper lters may cause the unit to overow.
ßDo not place the hot carafe on a cold or wet surface.
WARNING: Scalding may occur if the lid is removed during the brewing cycle.
WARNING Polythene bags over the product or packaging may be dangerous. To avoid danger of
suffocation, keep away from babies and children. These bags are not toys.

9
Instructions For Use
Before use, check the appliance for presence of foreign objects.
A Control Panel
1. On/Off button with LED Indicator
Featuring an audible tone (not shown) which beeps 5 times after the coffee has nished brewing.
Unit will automatically shut off.
2. Grind Off Button with LED Indicator
Use to turn off the grinder when using pre-ground coffee.
3 & 6. Hour and Minute Buttons
Press and hold either Hour or Min for approximately 2 seconds to enter Time Set Mode.
4. Cup Quantity Knob
Turn the Cup Quantity to choose the desired amount of coffee beans to grind (up to 12 cups).
1 2 3 4 5 6 7 8
Programme

10
5. Clock/LCD Display
Displays time of day (and programme setting when Programme button is pressed). Displays Strength
Control setting (MILD, MED or STRONG)
7. Strength Control Button
Press to select the required coffee strength: (MILD, MED or STRONG). Selected coffee strength will
show on the Clock Display.
8. Programme Button with LED Indicator
Press to display or set Auto On time.

11
B Programming
Setting the Clock
When the Grind & Brew Plus is plugged in, “12:00” will appear until you set the time.
Entering “Time Set” mode:
To set the time, press and hold either the “Hours” or “Minutes” button until the clock begins to ash
(approx. 2 seconds). This signals that you have entered the “Time set” mode. The desired time can be
set by pressing the “Hours” and “Minutes” buttons to scroll forward through the digits. The buttons
can be held down to scroll through the digits, or pressed and released lightly to advance one digit at
a time.
N.B. Be careful to make sure that the “PM” indicator is on if a “PM” time is desired.
Exiting “Time Set” mode:
There are 2 ways to exit the “Time Set Mode”:
ßPress any button besides the “Hours” or “Minutes” button. This will exit the “Time Set” mode and
activated the selected function.
ßDo not press any of the buttons on the control panel. If neither “Hours” nor “Minutes” button is
pressed for a period of 5 seconds, the “Time Set” mode will be exited automatically.

12
Setting the Programme Time
This feature allows you to pre-programme brewing for the desired time. By pressing the ’Programme’
button the digital display shows the current programme time. This default setting is 12:00pm.
Entering “Set Programme Time” mode:
Press and hold the “Programme Set” button until the green light and LCD display begin to ash,
this signals that you have entered the “Set Programme Time” mode. The desired time can be set by
pressing the “Hours” and “Minutes” buttons to scroll forward through the digits. The buttons can be
held down to scroll through the digits or pressed and released lightly to advance one digit at a time.
The coffee maker will start to brew at the programmed time.
N.B. The “Programme” mode cannot be entered if the coffeemaker is in a “brew” cycle.
N.B. When setting the programme time, ensure coffee and water are placed in the machine before
the automatic start (see “Preparing to Brew”)
Exiting “Set Programme Time” mode:
There are 3 ways to exit the “Set Programme Time”:
ßPress the “Programme” button, this acts as a “cancel” button and will cause the coffeemaker to
revert to its previous state. If it was OFF, it will return to the OFF position. If “Programmed” it will
revert to this state, and so on. This is a safety feature.
ßPress any other button (except “Hours” or “Minutes”). “Set Programme Time” mode will be exited
and the function of that button will be activated.
ßLeave the control. If neither “Hours” nor “Minutes” button is pressed for a period of 5 seconds, the
“Set Programme Time” mode will be exited automatically and the programmed setting will be in
effect.

13
C Inserting the Charcoal water filter
N.B. Your appliance is supplied with two charcoal water lters.
It is strongly recommended that the water lter is replaced after 90 days or 90 uses; more often if you
have hard water. Failure to do so can lead to a build-up of lime scale and affect the performance of
your appliance. Replacement lters can be purchased directly from the manufacturer, (see “UK After
Sales Service” section for further details).
ßRemove the lter from its packaging and soak in cold tap water for 15 minutes.
ßTo remove the water lter holder, simply lift it out from its opening on the inner wall of the
reservoir.
ßHold stem in one hand. With your other hand, gently press the compartment door down and pull
outwards to ip open.
ßPlace the lter in the holder and close the compartment cover; you will hear a snap indicating lter
is in place.
N.B. Caution must be used when inserting the charcoal lter. Improper placement in the holder can
cause tearing of the lter skin.
ßHold the lter under cold running tap water for 10 seconds to ush. Hold the water lter holder hori-
zontally, directly under the water stream so that the water ows through the lter compartment.
ßAllow the lter to drain completely.
ßReplace the water lter holder into its opening on the inner wall of the reservoir, pushing it all the way
down to the base of the unit.

14
D Preparing to Brew
N.B. Before making coffee for the rst time, we recommend operating the appliance once, using only
water, to remove any dust or residue that may remain in the system from the manufacturing process.
Ensure the burr grinder operates without beans for rst use.
Inserting the Filter
ßPress the lter basket door release button and remove the lter basket cover. When removing the
lter basket cover (especially after brewing) use the tab with the marking “lift” to do so as parts may
be hot after use. Ensure the Gold Tone® lter is positioned with the handle facing away from main
body of the appliance.
N.B. If the handle is not facing away, it may interfere with the ow of ground coffee into the lter
basket. Place the lter basket cover in place, ensuring that the “GRIND” arrow is matching the “LIFT”
arrow and then close the lter compartment door.
N.B. If the lter basket cover is not in place or the lter door is not shut properly, a safety interlock
system will prevent operation. If you try to turn the unit on when parts are not in place, the appliance
will beep continuously until the missing parts are installed and the lter door is closed. (The door will
click when closed properly)
1. Filter Basket Cover
2. Gold Tone®Filter
3. Filter Basket Door
4. Filter Basket

15
Adding Water & Coffee Beans
ßOpen the reservoir lid of the Grind & Brew Plus, pour the desired amount of water into the reservoir
using the water level indicator. Close the reservoir lid ensuring not to exceed the 12-cup line as this
may cause the carafe to over ow.
ßLift the Bean Hopper Lid and ll with desired quantity of beans. We recommend keeping the hopper
at least half full and ensuring there is a sufcient amount of beans in the hopper for the amount of
coffee that is intended for brewing.
WARNING: Maximum capacity for the hopper is 225g. Do not over fill or you may damage the
burr grinder and/or the unit may overflow.
ßFor easy lling or cleaning, the hopper can be completely removed by turning the hopper release
knob to the “un-lock” position (picture 1 below)
IMPORTANT: Take extra care not to spill water around the grind chamber. In the event that some
water is spilled in the chamber, dry thoroughly before use.
ßReplace the hopper lid
1
2
1. Bean Hopper release knob
2. Bean Hopper
3. Bean Hopper Lid
3

16
Locking the Bean Hopper
ßWhen replacing the hopper back onto the unit, ensure the hopper container release knob is in the
un-lock position. Once in place, turn the knob back into the locked position
N.B. If the hopper is not locked into place, the appliance will not operate. If you try to turn the unit on
with the hopper is not locked into place the appliance will beep continuously until the missing parts
are installed and you close the lid.
N.B. The Channel Cover must be in place before grinding otherwise the appliance will not function.
(see diagram below)
Restarting the process will not affect coffee results. If you do not want the grinder to restart, press
the “Grind off” button before pressing the ‘On/Off’ button. Once the hopper is locked back into pla-
ce, the beeping will stop. Press the ‘On/Off’ button and the grind and brew process will start again
from the beginning.

17
Preparing the Carafe
ßRemove thermal carafe lid by turning in the direction of the “unlock” arrow. Pre-warm the carafe by
rinsing it out with hot water. N.B. This will help keep the coffee hotter.
ßReturn the carafe lid to the carafe. To lock, align the arrows on the lid and the carafe and turn in a
clockwise direction until the lid ts tightly on carafe and the arrow lines up in the centre of the spout.
This ensures the lid is locked into place and in the correct position for brewing and pouring.
ßReplace the thermal carafe in its position on the resting plate. Plug the appliance into the mains.
1. Water Reservoir Cover
2. Water Filter Holder
3. Burr Grinder
4. Coffee Channel Assembly
a. Channel Cover (must be in
place before grinding)
b. Coffee Chute
c. Grind Chute Lever
5. Filter basket door release button
1 2 3 4a 4b 4c
5

18
E Grinding and Brewing Coffee
Now the coffee machine is ready to grind and brew.
Immediate Brewing
ßTurn the “Cup Quantity” knob to set the number of cups you want to brew, this will grind enough
coffee beans to suit your requirement
ßPress the “Strength Control” button to set the strength (MILD, MED, or STRONG) this will show on
the LCD display.
ßTo start the grinding and brewing process, press the ‘On/Off’ button. The indicator light will illuminate
and the process will begin.
Programmed Brewing
ßTo set the appliance to start at a programmed time, refer to “Set Programme Time” section B.
ßTurn the “Cup Quantity” knob to set the number of cups you want to brew, this will grind enough
coffee beans to suit your requirement.
ßPress the “Strength Control” button to set the strength (MILD, MED, or STRONG) this will show on
the LCD display.
ßThe Grind & Brew Plus will begin brewing at the programmed time
Brewed Coffee
ßWhen the brewing cycle has completed, 5 beeps will sound. Coffee will continue to stream from the
lter for several seconds afterwards.
ßWhen the coffee is ready, stir before serving, to blend the avours. The coffee at the bottom of the
carafe will be stronger than that at the top.

19
ßThe brew-through, pour-through lid allows coffee to drip from appliance through the closed lid.
When brewing is complete, the lid seals itself so air stays out and coffee freshness and temperature
are maintained. No need to turn or adjust the lid before pouring.
ßAfter brewing, the appliance will automatically shut off. The thermal carafe will keep the coffee hot
for hours.
ßThe ‘Automatic Brew Pause’ feature allows you to remove the carafe during mid-brew. The brewing
process does not stop during this period, only the ow of coffee from the basket to the carafe stops.
WARNING: do not remove the carafe for longer than 20 second or the coffee may overflow the
basket.
N.B. Whilst we offer this feature for your convenience, we do not recommend that you pour coffee
before the cycle has reached completion, since the coffee brewed at the beginning of the cycle has
a very different avour prole to that made at the end of the cycle. Removing a cup during the cycle
will alter the avour of the nished pot.
CAUTION: The bottom of the thermal carafe is hot to touch for several minutes after
brewing.

20
F Brewing Coffee with Pre-ground Beans
This appliance can also brew coffee using pre-ground beans. We recommend using 1 level scoop of
ground coffee per cup.
N.B The maximum basket capacity for ground coffee is 16 scoops. Exceeding this may cause the
appliance to overow.
ßOpen the lter door by pushing the release button and remove the lter basket lid.
ßScoop the ground coffee into the Gold Tone® lter. Place the lter basket lid in place and close the
lter door.
ßAdd the water as described previously in section “Preparing to Brew”
ßPrepare the carafe as previously described in “Preparing the carafe” section.
ßTurn off the grinding function, by pressing the “Grind Off” button, an amber light will illuminate, then
press the ‘On/Off’ button.
ßPlug the appliance into a suitable mains socket and press the ‘On/Off’ button, the indicator will light
and the brewing process will begin.
ßFor programmed brewing, set the timer as described in “setting the timer” section.
N.B. If the lter basket cover is not in place or the lter door is not shut properly, a safety interlock
system will prevent operation. If you try to turn the unit on when parts are not in place, the appliance
will beep continuously until the missing parts are installed and the lter door is closed. (The door will
click when closed properly)